Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “THROTTLING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

The Effects of Background Pressure on SPT-140 Hall Thruster Performance

NASA’s planned Psyche mission is scheduled to launch in 2022 and begin a 3.5-year cruise to the metallic asteroid Psyche, where it would examine this unique body. The baseline spacecraft design is a hybrid of JPL’s deep-space heritage subsystems with commercial partner SSL’s power, structure, and SPT-140 electric propulsion subsystems. Since the deepspace implementation of the SPT-140 differs from the commercial implementation, primarily in the need for deep power throttling, characterization of the system at lower powers is necessary. One specific area of interest is the sensitivity of thruster performance to background pressure in ground-based test facilities, which can have an impact on the prediction of in-space performance. Measurements of this pressure dependence were performed on a qualification-model SPT-140 thruster over the 0.9-4.5 kW range of interest for the Psyche mission. Thrust sensitivity to pressure, in an absolute sense, was largest at 4.5 kW and decreased with power until there was little-to-no measurable effect at 0.9 kW. In a relative sense, thrust sensitivity was similar at all powers above 0.9 kW with about 2-4% higher thrust measured at 10 µ µTorr than at the lowest operating pressure. Thruster magnetic field sensitivity, examined as a function of magnet current, did not have a strong dependence on facility pressure. Finally, an investigation of low-power operation at the lowest facility pressure showed that a combination of added cathode keeper current and additional cathode propellant flow significantly mitigated the larger negative cathode-to-ground voltages that were observed. These test results, combined with thruster life test results, inform the selection of proper low-power operating conditions for Psyche.

Mackey, Jonathan A.↗

SmallSat missions enabled by paired low-thrust hybrid rocket and low-power long-life Hall thruster

The capabilities of a SmallSat-class spacecraft targeting the outer solar system and using a combined chemical and electric propulsion system are explored. The development of compact hybrid rockets has enabled high-thrust engines to be packaged tightly enough to fit on cubesat and SmallSat spacecraft. These hybrid rockets provide 10’s-100 N of thrust depending on the propellant load & >300 s of specific impulse and have been demonstrated in both ambient and vacuum environments. Advancements in low-power long-life Hall thruster technologies have provided the potential for significantly greater propellant throughputs, enabling their use as a primary propulsion element on interplanetary spacecraft. In a recent characterization test campaign, the MaSMi-DM Hall thruster demonstrated power throttling from 150 – 1000 W with >1500 s of specific impulse available at >500 W and >40% total thrust efficiency available at >300 W; peak values of 1940 s and 53% were observed. A notional low-mass spacecraft employing a combined hybrid rocket and low-power electric propulsion system was designed and used for mission concept analysis targeting the outer solar system. Using an imposed wet mass limit of 400 kg, mission trajectories to Saturn and Uranus were generated. Orbit capture with >40% of the launch mass was shown to be possible at either target, with mission transfer times of 7.5 years and 13.5 years for Saturn and Uranus, respectively. Significant follow-on mission activities near Saturn (e.g. to Titan & Enceladus) were also possible by carrying extra propellant mass while remaining under the total wet mass limit.

Karp, Ashley C.↗

Performance of the 12.5-kW Advanced Electric Propulsion System Engineering Test Unit Hall Thruster

This work presents a summary of the performance test campaign of the 12.5 kW Advanced Electric Propulsion System (AEPS) Engineering Test Unit 2 (ETU-2) thruster produced by Aerojet Rocketdyne. This test campaign had three major goals: to assess design compliance with thruster requirements, provide a comparison to the previously-tested NASA Hall Effect Rocket with Magnet Shielding (HERMeS) Technology Demonstration Units (TDUs) from which the AEPS ETU design was derived, and support AEPS application on the Power and Propulsion Element (PPE). Assessments of ETU-2 performance were conducted at discharge powers of 2.6 to 13.1 kW, which encompasses the original AEPS throttle conditions as well as those most relevant for AEPS application on PPE. The results from the test campaign indicate that ETU-2 performance meets or exceeds all AEPS thruster performance requirements and matches the values and trends previously measured with the HERMeS TDUs. In addition, similar to the HERMeS TDUs, ETU-2 performance showed minimal variation over approximately 1636 h of operating time due to the incorporation of magnetic shielding. Taken together, these results show that the AEPS design is successfully replicating the performance of the HERMeS TDUs to within the empirical uncertainty and meeting its performance requirements as the design progresses to its Critical Design Review.

HERMeS↗

Performance of the 12.5-kW Advanced Electric Propulsion System Engineering Test Unit Hall Thruster

This work presents a summary of the performance test campaign of the 12.5 kW Advanced Electric Propulsion System (AEPS) Engineering Test Unit 2 (ETU-2) thruster produced by Aerojet Rocketdyne. This test campaign had three major goals: to assess design compliance with thruster requirements, provide a comparison to the previously-tested NASA Hall Effect Rocket with Magnet Shielding (HERMeS) Technology Demonstration Units (TDUs) from which the AEPS ETU design was derived, and support AEPS application on the Power and Propulsion Element (PPE). Assessments of ETU-2 performance were conducted at discharge powers of 2.6 to 13.1 kW, which encompasses the original AEPS throttle conditions as well as those most relevant for AEPS application on PPE. The results from the test campaign indicate that ETU-2 performance meets or exceeds all AEPS thruster performance requirements and matches the values and trends previously measured with the HERMeS TDUs. In addition, similar to the HERMeS TDUs, ETU-2 performance showed minimal variation over approximately 1636 h of operating time due to the incorporation of magnetic shielding. Taken together, these results show that the AEPS design is successfully replicating the performance of the HERMeS TDUs to within the empirical uncertainty and meeting its performance requirements as the design progresses to its Critical Design Review.

Jason D Frieman↗

Highlights of Aeroacoustic Tests of a Metal Spacecraft Cabin Ventilation Fan Prototype

A metal spacecraft cabin ventilation fan suitable for aerodynamic and acoustic ground tests was designed and tested in the NASA Glenn Research Center Acoustical Testing Laboratory. The fan design featured a low-noise blade-vane count that was chosen to reduce the rotor-stator interaction tone noise. The fan was throttled through its operating range, and results indicate that the measured aerodynamic and acoustic performance was in good agreement with predictions. Recommendations for further research of quiet high-performance fans intended to support long duration human space exploration missions are offered. This small fan aerodynamic and acoustic test rig and the NASA Glenn Acoustical Testing Laboratory are valuable resources available for supporting NASA’s aeronautics research and space exploration missions.

Fan↗

Fan Acoustic Flight Effects on the PAA & ASN Flight Test

Accurate and reliable prediction of noise emitted from turbofan aircraft engines is an ongoing challenge. For continued progress, it is necessary to assess the performance of the most recent prediction methods in the NASA Aircraft NOise Prediction Program (ANOPP), and to examine the effects of flight condition on fan noise. The assessment is based on an extensive acoustic dataset acquired as part of the Propulsion Airframe Aeroacoustics and Aircraft System Noise (PAA&ASN) Flight Test conducted on a Boeing 787-10 aircraft. Engine operating condition was varied to study the characteristics of fan noise in flight. In a subset of the flight test matrix, the influence of the aft duct acoustic liner was studied by covering the lined area with aluminum tape to simulate a hardwall duct. The combination of test data at different flight conditions, along with rigorous predictions of jet noise, is used in this paper to extract fan noise from the measured total aircraft noise levels. The measured fan noise levels are compared with those predicted using the latest methods for fan source noise, liner attenuation, and PAA effect prediction. Detailed analyses are undertaken to understand agreement between data and various aspects of the prediction models, including spectral shape, directivity, and response to throttle setting. An additional investigation was undertaken to study the effect of aircraft speed on fan noise, as current models do not directly account for this parameter.

Aircraft System Noise↗

Development of Slat-gap and Slat-cove Filler Treatments for Noise Reduction Assessment on the High Lift Common Research Model in the NASA LaRC 14x22

Airframe noise is an important issue during the approach and landing phases of flight because engines are throttled back, and airframe sources become an equal or greater contributor to environmental noise. The leading-edge slat component of the high-lift system for transport aircraft has been identified as a prominent source of airframe noise. Noise production mechanisms and potential treatments to mitigate airframe noise have been areas of active research for nearly three decades. Two promising technologies for slat noise reduction are the slat-gap filler (SGF) and slat-cove filler (SCF). Previous work was done using a 2D section of a transport class aircraft wing to demonstrate their feasibility via benchtop and computational models. A wind tunnel test campaign was recently undertaken to test the SGF and SCF technologies in a flight-like environment by installing dynamically scaled treatments on the 10%-scale High-Lift Common Research Model (CRM-HL), which is representative of a commercial twin-aisle transport aircraft. Advancement of the SGF and SCF technologies to overcome challenges of integration with 3D airframe structures, computational simulations of the CRM-HL predicting the aerodynamic and aeroacoustic performance and structural loads, and design of wind tunnel model hardware with features accommodating noise treatments were conducted in parallel. Details of innovations in the SGF and SCF technologies for 3D airframe feasibility will be described. The loads the treatments must sustain in flight and the influence of those loads on the design is also discussed. Finally, the design of wing leading-edge assemblies to treat the 10% CRM-HL with dynamically scaled SGF and SCF components is presented. The treatments were successfully tested in 2020/2021 providing a demonstration of leading-edge noise reduction using components that would allow slat articulation.

airframe noise reduction↗

Overview and Performance Characterization of Northrop Grumman’s 1 kW Hall Thruster String

Northrop Grumman (NG) Tactical Space SystemsDivisionhas embarked on the development and qualification of a high throughput, low power Hall Thruster String (HTS) using hardware designed and built in-house.Following the success of Mission Extension Vehicles 1 and 2, NG is currently developing the next generation in its lineupof satellite servicing capabilities, the Mission Robotics Vehicle(MRV)and Mission Extension Pod (MEP).MEP’s mission profile imposes highly demanding requirements upon the electric propulsion system. When surveying the industry for available systems, NGwas unable to identify any mature Hall thrustersystems that could satisfy the performance and lifetime requirements for MEP. Eventually, it was decided to vertically integrate the EP development process, partneringwith NASA Glenn Research Center to leverage ongoing development at GRC of a high throughput, low power Hall thruster. The components of the HTS have successfully passed PDR and are currently in the engineering development and test phase. Based on performancecharacterization testingof the development hardware,NG’s low power Hall thruster, dubbed the NGHT-1X, promises to deliver state-of-the-art performanceand lifetime for a sub-kW Hall thruster, achieving total efficiencies of 50-55% over a wide range of throttle conditions. Results of a seriesof characterization tests including integrated systems testingwith the PPUare presented.Qualification methodology andthruster lifetime verification is also discussed. Environmental qualification of the HTS components is expected to completein mid-2023 with a first flight in mid-2024.

Propulsion↗

Extended Wear Testing of the 12-kW Advanced Electric Propulsion System Engineering Test Unit Hall Thruster

This work presents a summary of the first wear test of the 12 kW Advanced Electric Propulsion System (AEPS) intended to isolate the impact of discharge current on component wear rates. Testing was led by Aerojet Rocketdyne and performed with the AEPS Engineering Test Unit 2 (ETU-2) thruster. In total, approximately 860 hours of operation were accumulated split between operating conditions of 600 V/9 kW, 600 V/11 kW, and 600 V/12 kW. Thruster performance and stability were invariant throughout the wear test for all thruster throttle conditions and shown to be equal to the values previously measured with ETU-2. Inner front pole cover erosion rates were found to be invariant to discharge current as the measurements at all three operating conditions were equal to within the empirical uncertainty. Outer front pole cover erosion rates were found to be equal for the 600 V/9 kW and 600 V/12 kW conditions with operation at 600 V/11 kW yielding elevated erosion rates. Overall, the data shows that the AEPS thruster design has a high probability of meeting lifetime and performance requirements as the design proceeds to flight production and qualification.

Jason D Frieman↗

Extended Wear Testing of the 12-kW Advanced Electric Propulsion System Engineering Test Unit Hall Thruster

This work presents a summary of the first wear test of the 12 kW Advanced Electric Propulsion System (AEPS) intended to isolate the impact of discharge current on component wear rates. Testing was led by Aerojet Rocketdyne and performed with the AEPS Engineering Test Unit 2 (ETU-2) thruster. In total, approximately 860 hours of operation were accumulated split between operating conditions of 600 V/9 kW, 600 V/11 kW, and 600 V/12 kW. Thruster performance and stability were invariant throughout the wear test for all thruster throttle conditions and shown to be equal to the values previously measured with ETU-2. Inner front pole cover erosion rates were found to be invariant to discharge current as the measurements at all three operating conditions were equal to within the empirical uncertainty. Outer front pole cover erosion rates were found to be equal for the 600 V/9 kW and 600 V/12 kW conditions with operation at 600 V/11 kW yielding rates that were comparable to those on the inner front pole cover. Overall, the data shows that the AEPS thruster design has a high probability of meeting lifetime and performance requirements as the design proceeds to flight production and qualification.

HERMeS↗

High Speed Inlet Distortion Test for the X 59 Low Boom Flight Demonstrator in the NASA Glenn 8-by 6-Foot Supersonic Wind Tunnel

The Low Boom Flight Demonstrator (LBFD) High Speed Inlet Distortion Test (HSIDT) was completed in the NASA Glenn Research Center 8- by 6-Foot Supersonic Wind Tunnel (8x6 SWT) using a 9.5 percent-scale propulsion model of the X–59 to evaluate the compatibility and operability of the inlet and engine integration, focusing on the inlet dynamic effects at the engine face. The model was instrumented with steady-state and high-response total pressure probes in the conventional 40-point, equal-area array at the aerodynamic interface plane (AIP). The HSIDT successfully collected high response distortion data points for the X–59 from Mach = 0 to 1.55 for a wide range of angle-of-attack, angle-of-sideslip, and inlet flow. Analyses showed that inlet dynamic distortion and inlet planar wave (or inlet buzz) were within engine limits through most of the flight envelope. The test data showed that inlet planar wave was present at Mach 1.35 and above, at airflows between idle and maximum engine airflow. Engine throttle back will need to be limited when decelerating from supersonic flight Mach to avoid these regions of inlet planar wave. The HSIDT data was also used to compare the metric SUM40, computed from the 40 high-response AIP total pressure probes, with the metric SUM4, computed from four high-response inlet static pressure probes. The data showed that SUM4 can be used as a surrogate for SUM40 during the X–59 flight test to detect inlet planar wave.

X-59↗

Highlights of Aeroacoustic Tests of a Metal Spacecraft Cabin Ventilation Fan Prototype

A metal spacecraft cabin ventilation fan suitable for aerodynamic and acoustic ground tests was designed and tested in the NASA Glenn Research Center Acoustical Testing Laboratory. The fan design featured a low-noise blade-vane count that was chosen to reduce the rotor-stator interaction tone noise. The fan was throttled through its operating range, and results indicated that the measured aerodynamic and acoustic performance was in good agreement with predictions. Recommendations for further research of quiet high-performance fans intended to support long duration human space exploration missions are offered. This small fan aerodynamic and acoustic test rig and the NASA Glenn Acoustical Testing Laboratory are valuable resources available for supporting NASA’s aeronautics research and space exploration missions.

Fan, Noise, Ventilation↗

Physics and Modeling of Quasi-Steady and Forced Shock Trains

The dual-mode scramjet is a propulsive concept for contemporary hypersonic vehicles promising flight cruise speeds upwards of Mach 5. Despite decades of development and a recent resurgence in interest, such engines are not routinely deployed for commercial or military purposes. Instead, they have been confined to the realm of ground-test research and limited one-off flight test missions. One of the key stumbling blocks on the critical path to deployment of a dual-mode scramjet is the optimal design and stable operation of the isolator, a typically constant area duct that separates the scramjet inlet from the combustor. During ramjet mode at Mach numbers from 3 to 5 and during the transition to scramjet mode at higher Mach numbers, the isolator contains the pseudo-shock. Necessary to meet the back-pressure in the combustor, the pseudo-shock is typically divided into a shock dominated shock train region followed by a turbulence driven mixing region. Fluctuations in combustor pressure due to vehicle maneuvering, throttling, or combustion instabilities drive the shock train to shift streamwise within the isolator. In response to sharp pressure fluctuations, the shock train is unable to stabilize within the isolator, and the scramjet unstarts by ejecting the shock train out the inlet. This work addresses three key gaps in understanding of the isolator pseudo-shock. The phenomenon is studied in three experimental facilities to investigate the quasi-steady and unsteady fluid dynamics of the shock train in fueled and un-fueled test conditions. The strong link between boundary layer morphology and shock train structure is studied in detail and used as a tool to evaluate the state-of-the-art definitions and models of the pseudo-shock. Identifying the limitations of these models, a new process driven flux-conserved pseudo-shock model is proposed. This provides a computationally efficient model grounded in the fluid dynamic mechanisms of the pseudo-shock with better predictive capability than the current state-of-the-art across all facilities tested. The unsteady behavior of the shock train is further investigated to identify and understand two distinct forced dynamic modes: mechanically induced, low-rate forcing and high-rate combustion driven unsteadiness that sheds upstream propagating shocks. The proposed process driven model is found to be effective in the the limiting case of high-rate combustion driven unsteadiness by evaluating the model in a shock stationary reference frame. Further analysis identifies the approximately rigid chain motion of the shock train structure to mechanically induced forcing. The time delay between the onset of forced dynamics is found to saturate to a constant value and maximum shock train speed along the isolator with respect to the perturbation rate of change. The result of this work provides dual-mode scramjet designers with improved tools and physical understanding to develop more efficient, robust, and capable propulsion systems for hypersonic vehicles.

JAXA↗

Hybrid-Electric Aero-Propulsion Controls Testbed Results

NASA is supporting the development of Electrified Aircraft Propulsion (EAP) technology due to its potential to reduce aircraft fuel burn, emissions, and noise as well as improving safety and performance. One focus of this research is the electrification of conventional turbomachinery propulsion systems, which offers ways to improve the performance and operability of turbine-engine powered aircraft through the addition of electro-mechanical systems. These hybrid-electric turbine engines provide additional actuation and energy management control opportunities for improving stability and transient response behavior. This paper summarizes the results of a Hardware-in-the-Loop (HIL) test performed at the NASA Electric Aircraft Testbed (NEAT) during the summer of 2022. The test demonstrates the feasibility and performance of an advanced energy management control strategy by integrating a simulated turbofan engine with scaled electro-mechanical hardware. A full-scale real-time reference model of a geared turbofan was run alongside a scaled electro-mechanical system representing the electrified turbofan components operating at a megawatt-scale power level. The model was interfaced with the hardware through a novel closed-loop control and scaling algorithm that emulated the dynamic speed and torque response of the turbofan shafts. The control strategy was implemented on the electrical machines connected to the emulated turbomachinery shafts. The results from the testbed are compared against simulations that predict the testbed and geared turbofan model operation. The energy management control strategy successfully changed the operating point of the engine model and improved its stability during throttle transients. These results also demonstrate the success of the novel closed loop control and scaling approach for emulating turbomachinery and elevate the Technology Readiness Level (TRL) of the energy management control strategy.

Aeronautics↗

Edge Wear of the Advanced Electric Propulsion System Pole Covers

This work summarizes a wear test focused on characterizing the erosion of the edges and side walls of the 12-kW Advanced Electric Propulsion System (AEPS) pole covers as well as the impact of magnetic field strength on component erosion for operation at a discharge voltage of 600 V. Testing was performed with the AEPS Engineering Test Unit 2 (ETU-2) thruster and accumulated approximately 325 hours of operation at the 600 V/12 kW condition with the magnetic field strength set to 75% of its nominal value. Thruster performance was invariant throughout the wear test for all thruster throttle conditions and matched previous measurements at the nominal magnetic field strength. Contrary to past results, inner front pole cover erosion rates were invariant to magnetic field strength at the 600 V/12 kW condition and no erosion was measured on the outer front pole cover. The erosion profile of the downstream inner front pole cover faces was continuous across the cover, indicating no significant change in erosion processes at the pole cover edges. Side wall erosion was only detected on the cathode-facing surfaces of the inner front pole cover and was equal in magnitude to the rates measured on the adjacent downstream edges. Taken together, these results suggest that erosion of the pole cover edges and sidewalls is driven by cathode-borne ions and will ultimately not impact AEPS life estimates.

Hall thrusters↗

Edge Wear of the Advanced Electric Propulsion System Pole Covers

This work presents a summary of the first wear test of the 12 kW Advanced Electric Propulsion System (AEPS) focused on characterizing the erosion of the edges and side walls of the thruster pole covers. Testing was performed with the AEPS Engineering Test Unit 2 (ETU-2) thruster and accumulated approximately 325 hours of operation at the 600 V/12 kW condition with the magnetic field strength set to 75% of its nominal value. Thruster performance was invariant throughout the wear test for all thruster throttle conditions and was found to be equal to previous measurements. Contrary to past results, inner front pole cover erosion rates were invariant to magnetic field strength at the 600 V/12 kW condition and no erosion was measured on the outer front pole cover. The erosion profile of the downstream inner front pole cover faces was continuous across the cover indicating no significant change in erosion process at the pole cover edges. Side wall erosion was only detected on the cathode-facing surfaces of the inner front pole cover and was equal in magnitude to the rates measured on the adjacent downstream edges. Taken together, these results suggest that erosion of the pole cover edges and sidewalls is driven by cathode-borne ions and will ultimately not impact AEPS life estimates.

Hall thrusters↗

Verification Testing and Veg-05 Tomato Crop Production on the International Space Station

Production of fresh, nutritious, and tasty produce for astronauts during spaceflight may provide health-promoting, bioavailable nutrients and enhance the dietary experience as we move into longer-duration missions. Growing and caring for plants may also reduce the psychological stresses associated with spaceflight and enhance connections to Earth. Requirements to consistently grow a diversity of crops under spaceflight environmental conditions remain poorly defined. The VEG-05 experiment is part of a series of experiments with pick-and-eat salad crops to better define best practices for crop production and handling in space. VEG-05 and predecessor experiments VEG-04A and VEG-04B, use the Veggie vegetable production facilities on the International Space Station to grow salad crops under different spectral compositions. In VEG-04A and B, mizuna mustard was cultivated with two different red: blue light treatments, and in VEG-05 we are cultivating ‘Red Robin’ dwarf cherry tomatoes under the same light spectra. Light can impact the growth habit, yield, nutritional composition, microbial levels, and even flavor attributes within crops, and our team will assess these characteristics for this crop during VEG-05. Prior to launch and installation on ISS in late 2022, both a science verification test (SVT), and an experiment verification test (EVT) were conducted at Kennedy Space Center in ISS Environment Simulator Chambers. Science verification testing, and a previous fertilizer test, grew plants in both plant pillows and PONDS (Passive Orbital Nutrient Delivery System) units and tested two different fertilizer treatments in both sets of hardware, with each test under only one of the light conditions. Because of challenges validating the PONDS hardware on ISS, and with good crop production in plant pillows, the EVT moved forward using only plant pillows with the highest fertilizer composition tested during SVT, and two Veggie units were utilized. One Veggie had light settings consisting of equal levels of red: blue light (150 µmol/m2/s for each color) plus green light (30 µmol/m2/s) while the second Veggie had a 90:10 ratio of red: blue light (270 µmol/m2/s red and 30 µmol/m2/s blue) plus green, so each unit provided 330 µmol/m2/s of photosynthetically active radiation to the tomato crops on average. Our original plan, based on prior ground testing, was to grow the crop for 104 days and harvest at 80, 90 and 104 days after initiation. For SVT, under the equal red: blue light treatment, fruit ripening in plant pillows was delayed and fruit were not ripe by day 80, so actual harvest days were days 90, 97, and 104. For EVT we saw fruit ripening earlier, especially in the high red treatment, and so we harvested at days 83, 90, and 99 days after initiation. In SVT we had mostly daily watering, and this led to excess water in plant pillows, which leaked out. This excess water also caused fungus to grow on one leaf and a couple of plant stems. To reduce this excess moisture, we throttled back the watering for EVT, and used the root mat reservoir more frequently. This led to watering only every other day, reducing crew time needed for plant care, however, two wilting events occurred during this EVT, at days 51 and 75. Plants recovered from these wilting events, but these events may have influenced the rate of fruit ripening and flower formation. Regardless, more than 10 fruit were produced from each plant on average, with the high red treatment producing slightly heavier fruit. Microbial testing from fruit during SVT indicated that fruit were safe for consumption with microbial levels below detection limits. VEG-05 flight and ground operations are expected to run between December 2022 and March 2023. This research was co-funded by the Human Research Program and Space Biology (MTL#1075) in the ILSRA 2015 NRA call.

Gioia D. Massa↗

Quiet Spacecraft Cabin Ventilation Fan: Vibration Measurements Results

Quiet, efficient fans with minimal vibrations are needed to maximize the mechanical life of atmospheric revitalization system fans used for human life support systems for long duration space exploration missions. Several metal spacecraft cabin ventilation fan prototypes have been designed, built, and tested at the NASA Glenn Research Center Acoustical Testing Laboratory. Tests performed in 2021 of the first prototype of the metal fan measured vibrations greater than desired at design point speed and backpressure conditions. To try to reduce those vibrations, a second prototype of the fan design was developed which included a new lighter rotor with a tighter balance tolerance, a new collet to attach the rotor to the motor shaft more securely and repeatably, and a new bracket to center and hold the motor in the fan centerbody more precisely. The second prototype of the fan was tested in 2023 and the vibrations were measured with the fan operating at design point speeds in isolation but not throttled to design point back pressure conditions since it was not installed with inlet and exhaust ducting. Peak vibration was reduced from 4 mm/s to 1 mm/s. This paper is part of a series of reports documenting the performance of the prototype fan.

Fan↗