Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Solar cell”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Peeled film GaAs solar cell development

Thin-film, single-crystal gallium arsenide (GaAs) solar cells could exhibit a specific power approaching 700 W/kg including coverglass. A simple process has been described whereby epitaxial GaAs layers are peeled from a reusable substrate. This process takes advantage of the extreme selectivity of the etching rate of aluminum arsenide (AlAs) over GaAs in dilute hydrofluoric acid. The feasibility of using the peeled film technique to fabricate high-efficiency, low-mass GaAs solar cells is presently demonstrated. A peeled film GaAs solar cell was successfully produced. The device, although fractured and missing the aluminum gallium arsenide window and antireflective coating, had a Voc of 874 mV and a fill factor of 68 percent under AM0 illumination.

Wilt, D. M.↗
NASA NTRS1994

Development of a lightweight, light-trapped, thin GaAs solar cell for spacecraft applications

This paper describes ultra-lightweight, high performance, thin, light trapping GaAs solar cells for advanced space power systems. The device designs can achieve 24.5 percent efficiency at AMO and 1X conditions, corresponding to a power density of 330 W/m2. A significant breakthrough lies in the potential for a specific power of 2906 W/kg because the entire device is less than 1.5 microns thick. This represents a 440 percent improvement over conventional 4-mil silicon solar cells. In addition to being lightweight, this thin device design can result in increased radiation tolerance. The attachment of the cover glass support to the front surface has been demonstrated by both silicone and electrostatic bonding techniques. Device parameters of 1.002 volts open-circuit voltage, 80 percent fill factor, and a short-circuit current of 24.3 mA/sq cm have been obtained. This demonstrates a conversion efficiency of 14.4 percent resulting in a specific power of 2240 W/kg. Additionally, this new technology offers an alternative approach for enabling multi-bandgap solar cells and high output space solar power devices. The thin device structure can be applied to any 3-5 based solar cell application, yielding both an increase in specific power and radiation tolerance.

Hannon, Margaret H.↗
DOE OSTI2023

Effects of Residual DMSO Adduct on Photonically Cured MAPbI 3 Solar Cells

Defects and impurities in halide perovskite solar cells can negatively impact device performance and long-term stability. In this study, we identify photonically cured methylammonium (MA) lead iodide films contain a residual adduct, MA 2 Pb 3 I 8 (dimethyl sulfoxide) 2 (MA 2 Pb 3 I 8 (DMSO) 2 ), that reduces photocurrent generation in perovskite solar cells (PSCs). This is evidenced by a decrease in the external quantum efficiency (EQE) near 400 nm. Similar EQE reductions were observed in PSCs produced using high-speed processes but have not been thoroughly examined. Through X-ray diffraction patterns and Fourier transform infrared spectroscopy, we establish the photo-inactive MA 2 Pb 3 I 8 (DMSO) 2 as the culprit for the EQE reduction. Combined experimental and simulation results reveal that the MA 2 Pb 3 I 8 (DMSO) 2 phase is located at the hole transport layer/ interface, not on the surface, resulting in lower quantum efficiency and surface photovoltage in the short wavelength region. The residual adduct is kinetically trapped due to the short processing time (20 ms) and crystallization direction but can be removed by an additional photonic pulse. Furthermore, this study highlights the need for careful examination of resulting materials beyond device efficiency when transitioning from laboratory processing to industrial high-speed methods.

14 SOLAR ENERGY↗
NASA NTRS1980

Updating the limit efficiency of silicon solar cells

The limit efficiency of a silicon solar cell is investigated using an analytical approach. The analytical model is based on the solution of a transport equation for minority carriers derived from the Shockley equations. On the basis of the computations, a 'narrow-region' design approach is suggested for both the front and the back regions of the solar cell. The design relies on low effective surface-recombination velocities, a textured front surface, and an optical internally reflecting back surface. With this approach, the limit efficiency is near 25%, and the optimum cell is 50 to 150 microns thick.

Wolf, M.↗
NASA NTRS2002

Ozone Correction for AM0 Calibrated Solar Cells for the Aircraft Method

The aircraft solar cell calibration method has provided cells calibrated to space conditions for 37 years. However, it is susceptible to systematic errors due to ozone concentrations in the stratosphere. The present correction procedure applies a 1 percent increase to the measured I(sub SC) values. High band-gap cells are more sensitive to ozone absorbed wavelengths (0.4 to 0.8 microns) so it becomes important to reassess the correction technique. This paper evaluates the ozone correction to be 1+O3xFo, where O3 is the total ozone along the optical path, and Fo is 29.8 x 10(exp -6)/du for a Silicon solar cell, 42.6 x 10(exp -6)/du for a GaAs cell and 57.2 x 10(exp -6)/du for an InGaP cell. These correction factors work best to correct data points obtained during the flight rather than as a correction to the final result.

Snyder, David B.↗
NASA NTRS1984

Advances in large area polycrystalline solar cells

Polycrystaline silicon is presently routinely processed into low cost 10 cm by 10 cm solar cells. However assuming minimal handling difficulties, only minor equipment modifications and no increase in processing complexity, the fabrication of even larger geometries would be economically advantageous. This investigation addressed the feasibility of developing 10 cm by 15 cm solar cells from research through pilot line production stages. The major thrust was to minimize costing by using existing production equipment and proven techniques wherever possible. Accordingly methods were developed to section larger substrates from existing cast ingots, a simple solar cell was designed and low cost processes implemented. After numerous preliminary experiments, pilot line production of 1500 cells was completed. Of these approximately 62 percent exhibited efficiencies greater than 7.0 percent, 53 percent were greater than 8.0 percent and 15 percent were greater than 9.0 percent. Based on this study, the regular production of 10 cm by 15 cm solar cells was determined to be both feasible and cost effective using existing processing methods.

Vendura, G. J., Jr.↗
NASA NTRS1977

Solar-cell array design handbook

Twelve-chapter two-volume compilation of solar cell design data is written from industrial, university, and governmental sources. Volumes contain tutorial descriptions of analytical methods, solar-cell characteristics, and cell material properties widely used in specifying solar-cell array performance and hardware design, as well as analysis, fabrication, and test methods.

Rauschenbach, H. S.↗
DOE OSTI2023

First of Their Kind: Solar Cells with a Dry-Processed Perovskite Absorber Layer via Powder Aerosol Deposition and Hot-Pressing

Preparing halide perovskite films by solvent-free, powder-based processing approaches currently attracts more and more attention. However, working solar cells employing dry, powder-based halide perovskite thin films, have not been demonstrated so far. Herein, perovskite solar cells are presented where the absorber layer is prepared by transferring readily synthesized perovskite powders into a compact thin film using a fully dry-powder-processing concept. Compact thin films are deposited via an optimized powder aerosol deposition (PAD) process. Pressing at 120 °C further improves the morphology and the optoelectronic film properties. Integrating the perovskite films in a solar cell configuration results in fully working devices, with champion power conversion efficiencies of >6%. While the (optoelectronic) properties of the PAD-processed films are found to be comparable with their solution-processed counterparts, investigations of the solar cell stack suggest deterioration of the electron-transport layer properties due to the PAD process, and the presence of hydrates at the perovskite surface to be important factors that contribute to the limited solar cell efficiency. Herein, perspectives to overcome the identified limitations are outlined, emphasizing the high potential and realizability of efficient perovskite solar cells based on dry-powder-processing approaches in the future.

14 SOLAR ENERGY↗
NASA NTRS1992

The effect of the low Earth orbit environment on space solar cells: Results of the advanced photovoltaic experiment (S0014)

The Advanced Photovoltaic Experiment (APEX), containing over 150 solar cells and sensors, was designed to generate laboratory reference standards as well as to explore the durability of a wide variety of space solar cells. Located on the leading edge of the Long Duration Exposure Facility (LDEF), APEX received the maximum possible dosage of atomic oxygen and ultraviolet radiation, as well as enormous numbers of impacts from micrometeoroids and debris. The effect of the low earth orbital (LEO) environment on the solar cells and materials of APEX will be discussed in this paper. The on-orbit performance of the solar cells, as well as a comparison of pre- and postflight laboratory performance measurements, will be presented.

Brinker, David J.↗
DOE OSTI2021

Long-Term Degradation of Passivated Emitter and Rear Contact Silicon Solar Cell under Light and Heat

Advanced designs enable high-efficiency solar cells; however, more complex structures create new long-term stability concerns. Herein, the long-term degradation processes affecting advanced silicon solar cells using laboratory-based illumination and heating over hundreds of hours are investigated. The activation energy for the degradation of voltage is estimated and the degradation rates to normal solar cell operating temperature ranges are extrapolated. The cell degradation observed at high temperatures in the lab is kinetically similar to the process affecting field-deployed modules contributing to 0.37% year-1 of annualized degradation. Electroluminescence and photoluminescence mapping show that the degradation is dominated by minority carrier lifetime reduction. Suns-open-circuit voltage and light beam-induced current results indicate that the degradation could result from passivation degradation at the surface or defect formation in the near-subsurface region, leading to increased minority carrier recombination. This work highlights a long-term degradation process under elevated temperature and illumination that may continue to affect cells in an irreversible manner that is separate from recoverable light-induced degradation and light- and elevated temperature-induced degradation.

14 SOLAR ENERGY↗
NASA NTRS1985

Some practical considerations for economical back contact formation on high efficiency solar cells

The back contact can detract from solar cell performance in a number of ways: high recombination, barrier, photovoltaic, minority carrier collection, resistance. These effects may act in a nonuniform fashion over the cell area, and complicate the analysis of photovoltaic performance aimed at a better understanding of the effects of device geometry and material and/or processing parameters. The back contact is tested by reproducing it on both sides of a substrate. The objective is to find a back contact which performs well as a back contact, can be applied cheaply to large area solar cells, fits well into a practical process sequence, does not introduce structural damage or undesirable impurities into the silicon substrate, is compatible with an effective front contact technology, permits low temperature solder contacting, adheres well to silicon, and is reliable.

Lesk, I. A.↗
DOE OSTI2020

Damp Heat Induced Degradation of Silicon Heterojunction Solar Cells With Cu-Plated Contacts

Damp heat exposure is one of the most stringent environments for testing the durability of solar cells in packaged modules. Damp heat stresses and induces a variety of degradation modes in solar cells and modules: for example, moisture-induced corrosion of electrodes and interconnections, deterioration of polymeric materials, and/or thermally activated diffusion processes. To screen for these and other potential degradation modes, we subject one-cell modules containing silicon heterojunction (SHJ) solar cells with Cu-plated contacts to extended damp heat tests at 85 °C/85% relative humidity. SHJ cells were laminated with two common encapsulants: ethylene vinyl acetate (EVA) and polyolefin elastomer (POE), and two constructions: glass-backsheet and glass-glass. We observe degradation in all components of solar cell maximum power (PMP): current, voltage, and fill factor, and find evidence of increased carrier recombination and nonideal diode behavior with increasing stress. For glass-backsheet constructions, EVA samples generally degrade more than POE by a factor of approximately 1.5x PMP, and the different encapsulants produce different degradation patterns. Similar trends are observed in glass-glass modules, but to a lesser degree. In a different experiment, we observe a decrease in effective minority carrier lifetime of nonmetallized SHJ precursors measured after damp heat. This implies that some degradation unrelated to the contacts is to be expected and confirms the observation of increasing recombination.

14 SOLAR ENERGY↗
NASA NTRS1976

Flexible, FEP-Teflon covered solar cell module development

Techniques and equipment were developed for the large scale, low-cost fabrication of lightweight, roll-up and fold-up, FEP-Teflon encapsulated solar cell modules. Modules were fabricated by interconnecting solderless single-crystal silicon solar cells and heat laminating them at approximately 300 C between layers of optically clear FEP and to a loadbearing Kapton substrate sheet. Modules were fabricated from both conventional and wraparound contact solar cells. A heat seal technique was developed for mechanically interconnecting modules into an array. The electrical interconnections for both roll-up and fold-up arrays were also developed. The use of parallel-gap resistance welding, ultrasonic bonding, and thermocompression bonding processes for attaching interconnects to solar cells were investigated. Parallel-gap welding was found to be best suited for interconnecting the solderless solar cells into modules. Details of the fabrication equipment, fabrication processes, module and interconnect designs, environmental test equipment, and test results are presented.

Rauschenbach, H. S.↗
NASA NTRS1977

Real-time and accelerated outdoor endurance testing of solar cells

Real-time and accelerated outdoor endurance testing was performed on a variety of samples of interest to the National Photovoltaic Conversion Program. The real-time tests were performed at seven different sites and the accelerated tests were performed at one of those sites in the southwestern United States. The purpose of the tests were to help evaluate the lifetime of photovoltaic systems. Three types of samples were tested; transmission samples of possible cover materials, sub-modules constructed using these materials attached to solar cells, and solar cell modules produced by the manufacturers for the ERDA program. Results indicate that suitable cover materials are glass, FEP-A and PFA. Dirt accumulation and cleanability are important factors in the selection of solar cell module covers and encapsulants.

Forestieri, A. F.↗
NASA NTRS1973

Development of a lightweight body-mounted solar cell array with a high power to weight ratio.

Three lightweight solar cell arrays have been fabricated with a high power-to-weight ratio. These arrays incorporate resistance welded interconnections, improved antireflection coating on the solar cell and lightweight substrates. Two of the substrates were constructed of magnesium with different structural geometry, while the third substrate was conventional aluminum honeycomb. All arrays utilized thin solar cells having a titanium-palladium-silver contact system and an antireflection coating of titanium oxide. The cells were welded with silver plated molybdenum interconnections. The two arrays having magnesium substrates exhibited a power/weight of 70.4 W/kg (32 W/lb.) and 81 W/kg (36.8 W/lb.), while the conventional array demonstrated a power/weight of 45.2 W/kg (20.6 W/lb.).

Somberg, H.↗
NASA NTRS2005

Recent Progress in CuInS2 Thin-Film Solar Cell Research at NASA Glenn

The National Aeronautics and Space Administration (NASA) is interested in developing low-cost highly efficient solar cells on light-weight flexible substrates, which will ultimately lower the mass-specific power (W/kg) of the cell allowing extra payload for missions in space as well as cost reduction. In addition, thin film cells are anticipated to have greater resistance to radiation damage in space, prolonging their lifetime. The flexibility of the substrate has the added benefit of enabling roll-to-roll processing. The first major thin film solar cell was the "CdS solar cell" - a heterojunction between p-type CuxS and n-type CdS. The research on CdS cells started in the late 1950s and the efficiency in the laboratory was up to about 10 % in the 1980s. Today, three different thin film materials are leading the field. They include amorphous Si, CdTe, and Cu(In,Ga)Se2 (CIGS). The best thin film solar cell efficiency of 19.2 % was recently set by CIGS on glass. Typical module efficiencies, however, remain below 15 %.

Jin, M. H.-C.↗
NASA NTRS1975

Efficiency of silicon solar cells as a function of base layer resistivity

This paper reports on a theoretical study of the limitations on silicon solar-cell efficiency for both n(+)-p and n(+)-p-p(+) type cells. Detailed calculations have been made of solar-cell operation using a general computer analysis program for semiconductor devices. The computer program, which simultaneously solves Poisson's equation and the electron and hole quasi-Fermi level equations, provides an accurate numerical solution of solar-cell operation without limiting assumptions or approximations. It is found that minority-carrier lifetime and heavy doping effects in the n(+) surface region present serious limitations to efficiency in low-resistivity silicon solar cells.

Dunbar, P. M.↗
NASA NTRS1982

Thickness dependences of solar cell performance

The significance of including factors such as the base resistivity loss for solar cells thicker than 100 microns and emitter and BSF layer recombination for thin cells in predicting the fill factor and efficiency of solar cells is demonstrated analytically. A model for a solar cell is devised with the inclusion of the dopant impurity concentration profile, variation of the electron and hole mobility with dopant concentration, the concentration and thermal capture and emission rates of the recombination center, device temperature, the AM1 spectra and the Si absorption coefficient. Device equations were solved by means of the transmission line technique. The analytical results were compared with those of low-level theory for cell performance. Significant differences in predictions of the fill factor resulted, and inaccuracies in the low-level approximations are discussed.

Sah, C. T.↗