Detection and Localization of Disconnections in a Large-Scale String of Photovoltaics Using SSTDR
Not provided.
Energy & Fuels↗
SEARCH · Engineering Papers
Results for “Soft materials”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Collagen Fibril Orientation in Tissue Specimens From Atherosclerotic Plaque Explored Using Small Angle X-Ray Scattering
Atherosclerotic plaques can gradually develop in certain arteries. Disruption of fibrous tissue in plaques can result in plaque rupture and thromboembolism, leading to heart attacks and strokes. Collagen fibrils are important tissue building blocks and tissue strength depends on how fibrils are oriented. Fibril orientation in plaque tissue may potentially influence vulnerability to disruption. While X-ray scattering has previously been used to characterize fibril orientations in soft tissues and bones, it has never been used for characterization of human atherosclerotic plaque tissue. This study served to explore fibril orientation in specimens from human plaques using small angle X-ray scattering (SAXS). Additionally, plaque tissue was extracted from human femoral and carotid arteries, and each tissue specimen contained a region of calcified material. Three-dimensional (3D) collagen fibril orientation was determined along scan lines that started away from and then extended toward a given calcification. Fibrils were found to be oriented mainly in the circumferential direction of the plaque tissue at the majority of locations away from calcifications. However, in a number of cases, the dominant fibril direction differed near a calcification, changing from circumferential to longitudinal or thickness (radial) directions. Further study is needed to elucidate how these fibril orientations may influence plaque tissue stress–strain behavior and vulnerability to rupture.
60 APPLIED LIFE SCIENCES↗
Long-Term Thermal Aging of Modified Sylgard 184 Formulations
Primarily used as an encapsulant and soft adhesive, Sylgard 184 is an engineered, high-performance silicone polymer that has applications spanning microfluidics, microelectromechanical systems, mechanobiology, and protecting electronic and non-electronic devices and equipment. Despite its ubiquity, there are improvements to be considered, namely, decreasing its gel point at room temperature, understanding volatile gas products upon aging, and determining how material properties change over its lifespan. In this work, these aspects were investigated by incorporating well-defined compounds (the Ashby–Karstedt catalyst and tetrakis (dimethylsiloxy) silane) into Sylgard 184 to make modified formulations. As a result of these additions, the curing time at room temperature was accelerated, which allowed for Sylgard 184 to be useful within a much shorter time frame. Additionally, long-term thermal accelerated aging was performed on Sylgard 184 and its modifications in order to create predictive lifetime models for its volatile gas generation and material properties.
36 MATERIALS SCIENCE↗
Microscopic Origins of the Nonlinear Behavior of Particle-Filled Rubber Probed with Dynamic Strain XPCS
The underlying microscopic response of filler networks in reinforced rubber to dynamic strain is not well understood due to the experimental difficulty of directly measuring filler network behavior in samples undergoing dynamic strain. This difficulty can be overcome with in situ X-ray photon correlation spectroscopy (XPCS) measurements. The contrast between the silica filler and the rubber matrix for X-ray scattering allows us to isolate the filler network behavior from the overall response of the rubber. This in situ XPCS technique probes the microscopic breakdown and reforming of the filler network structure, which are responsible for the nonlinear dependence of modulus on strain, known in the rubber science community as the Payne effect. These microscopic changes in the filler network structure have consequences for the macroscopic material performance, especially for the fuel efficiency of tire tread compounds. In this work, we elucidate the behavior with in situ dynamic strain XPCS experiments on industrially relevant, vulcanized rubbers filled (13 vol %) with novel air-milled silica of ultrahigh-surface area (UHSA) (250 m 2 /g). The addition of a silane coupling agent to rubber containing this silica causes an unexpected and counterintuitive increase in the Payne effect and decrease in energy dissipation. For this rubber, we observe a nearly two-fold enhancement of the storage modulus and virtually equivalent loss tangent compared to a rubber containing a coupling agent and conventional silica. Interpretation of our in situ XPCS results simultaneously with interpretation of traditional dynamic mechanical analysis (DMA) strain sweep experiments reveals that the debonding or yielding of bridged bound rubber layers is key to understanding the behavior of rubber formulations containing the silane coupling agent and high-surface area silica. These results demonstrate that the combination of XPCS and DMA is a powerful method for unraveling the microscale filler response to strain which dictates the dynamic mechanical properties of reinforced soft matter composites. With this combination of techniques, we have elucidated the great promise of UHSA silica when used in concert with a silane coupling agent in filled rubber. Such composites simultaneously exhibit large moduli and low hysteresis under dynamic strain.
36 MATERIALS SCIENCE↗
Twists and Puckers: Tuning Crystal Chemistry in the La(Au x Ge 1– x ) 2 Compositional Series
The physical properties of solid-state materials are closely tied to their crystal structure, yet our understanding of how competing structural arrangements energetically compare is limited. In this work, we explore how small differences in composition affect structure in the La(Au x Ge 1-x ) 2 series of compounds, comprising four unique structure types between LaGe 2 and LaAu 2 . This family includes the previously unknown AlB2-type compound with the stoichiometry La(Au 0.375 Ge 0.625 ) 2 , as well as La(Au 0.25 Ge 0.75 ) 2 , an intergrowth of the AlB 2 and ThSi 2 structure types. We then study the chemical forces driving the structure changes, including using phonon band structure calculations and DFT Chemical Pressure to evaluate atomic size effects. These calculations show that the parent AlB 2 structure type is disfavored in Au-rich compounds due to soft atomic motions along the c axis. The instability of AlB 2 -type LaAuGe is confirmed by the presence of imaginary modes in the phonon band structure that correspond to a ‘puckering’ of the hexagonal AlB 2 -type lattice, resulting in the experimentally observed LiGaGe structure type. The impact of size effects is less clear for Au-poor compositions; instead, ‘twisting’ the AlB 2 structure type to form the ThSi 2 type opens a pseudogap at the Fermi level in the electronic density of states. Here, this investigation demonstrates how crystal structure in solid-state materials can be compositionally tuned based on balancing size and electronics when multiple structure types are in close thermodynamic competition.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Effects of particle inclusions on cracking in ultrathin barrier films
Here, the effects of particle inclusions with different mechanical properties on the development of cracks in ultra-thin barrier films have been studied. Two types of particles, alumina and poly(styrene-b-methyl methacrylate) with large differences in their elastic modulus were used, representing both hard and soft inclusions. Particles were seeded onto polyethylene naphthalate substrates and subsequently coated with atomic layer deposited Al 2 O 3 as a barrier film. Ca corrosion tests used to determine the performance of the barrier films revealed that soft polymer particle inclusions severely affect the development of cracking in barrier films as compared to stiff ceramic particles. Tensile tests also confirmed that the barrier films with polymer particle inclusions have the lowest value of critical onset strain. Parametric simulations, conducted by varying the elastic modulus of the particle inclusions over a wide range, resulted in a larger strain energy release rate near particle inclusions which promotes crack formation and negatively impacts the performance of barrier films with softer particle inclusions. Thus, the combination of high residual stresses in the barrier films with the presence of soft particle inclusions is found the most detrimental for the development of high-performance ultrathin barrier films.
36 MATERIALS SCIENCE↗
Bayesian inference of anisotropic 2D small-angle scattering from sparse measurement
Here, we present a Bayesian inference framework for reconstructing anisotropic two-dimensional small-angle scattering (2D SAS) patterns from sparse, noisy, or partially missing data. The method combines a symmetry-aware angular basis with radial Gaussian process priors to enable accurate, training-free interpolation and denoising. Computational benchmarks demonstrate reliable recovery of both isotropic and high-order anisotropic features under severe data reduction. Experimental validations on stretched polymers, sheared wormlike micelles, and carbon fibers show improved fidelity and resolution compared to raw measurements, achieving comparable accuracy with up to 50-fold fewer detected neutrons. This approach enables quantitative structural analysis under low-flux, time-limited, or single-shot conditions, extending the applicability of 2D SAS techniques to compact neutron sources and mechanically driven soft matter systems undergoing transient structural changes.
Tung, Chi-Huan [Oak Ridge National Laboratory (ORN↗
Antiferromagnetic real-space configuration probed by dichroism in scattered x-ray beams with orbital angular momentum
X-ray beams with orbital angular momentum (OAM) are a promising tool for x-ray characterization techniques. Beams with OAM have a helicity - an azimuthally varying phase - which leads to a gradient of the light field. New material properties can be probed by utilizing the helicity of an OAM beam. Here, we demonstrate a dichroic effect in resonant diffraction from an artificial antiferromagnet with a topological defect. We found that the scattered OAM beam has circular dichroism at the antiferromagnetic Bragg peak whose sign is coupled to its helicity, which reveals the real-space configuration of the antiferromagnetic ground state. Thermal cycling of the artificial antiferromagnet can change the ground state, as indicated by reversal of the sign of circular dichroism. This result is one of the first demonstrations of a soft x-ray spectroscopy characterization technique utilizing the OAM of x rays. In conclusion, this helicity-dependent circular dichroism exemplifies the potential to utilize OAM beams to probe matter in a way that is inaccessible using currently available x-ray techniques.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Tailored Silicone Network Architecture for Ultimate Mechanical Reinforcement
Hydrosilylation cured silicone elastomers are subject to reaction inefficiency, leading to incomplete and non-uniform crosslink networks, restricting the potential of mechanical reinforcement. This work investigates pre-synthesized, functional PDMS architectures as additives to improve ultimate mechanical performance relative to conventional single-step curing. Three custom, functional structures were prepared: a partially crosslinked PDMS scaffold (Structure A), a bottle-brush PDMS (Structure B), and a star-shaped PDMS derived from an MQ resin (Structure C). Rheological characterization was used to identify the ultimate design space and proper stoichiometric ratio for Structure A, and confirm successful formation of all structures for suitable incorporation into a base silicone formulation at 30wt%. Mechanical tests indicated that all three structures increased in ultimate tensile strength relative to their single-step counterparts, with Structure A providing additional improvements to toughness (432 vs. 258 kJ/m3) and ultimate elongation (158 vs. 115%). Furthermore, Structure B remained very soft in the unfilled state, while Structure C provided hardness (23 vs. 18 Shore A) and stiffness (780 vs. 420 kPa Young’s modulus) increases. In silica filled systems, Structure A retained increased strength but reduced elongation, while Structure B indicated strong reinforcement in terms of strength, toughness, and stiffness. Thermal analysis on the cure profiles of these materials suggested that pre-formation of network architectures enable a more complete reaction than a single-step process (15.9 vs. 15.1 J/g). Ultimately, these results indicate that tailoring PDMS architecture before the final cure can improve ultimate mechanical properties via improved network development in silicone elastomers. Furthermore, this work offers a promising strategy for designing higher-performance, more tunable silicone formulations.
36 MATERIALS SCIENCE↗
Raman Fingerprints of Phase Transitions and Ferroic Couplings in van der Waals Multiferroic CuCrP 2 S 6
CuCrP 2 S 6 (CCPS), a type-II multiferroic material, exhibits unique phase transitions involving ferroelectric, antiferroelectric, and antiferromagnetic ordering. Here, in this study, we conduct a comprehensive investigation on the intricate phase transitions and their multiferroic couplings in CCPS across a wide temperature range from 4 to 345 K through Raman spectroscopic measurements down to 5 cm –1 . We first assign the observed Raman modes with the support of theoretical calculations and angle-resolved polarized Raman measurements. We further present clear signatures of phase transitions from the analyses of temperature-dependent Raman spectral parameters. Particularly, two low-frequency soft modes are observed at 36.1 cm –1 and 70.5 cm –1 below 145 K, indicating the antiferroelectric to quasi-antiferroelectric transition. Moreover, phonon mode hardening is observed when the temperature increases from 4 to 65 K, suggesting negative thermal expansion (NTE) and strong magnetoelastic coupling below 65 K. These findings advance the understanding of vdW multiferroic CCPS, paving the way for future design and engineering of multiferroicity in cutting-edge technologies, such as spintronics and quantum devices.
37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
Optimization of echo-enabled harmonic generation toward coherent EUV and soft X-ray free-electron laser at NSLS-II
Prebunching via echo-enabled harmonic generation (EEHG) is an efficient way to reduce the radiator length and improve the longitudinal coherence as well as output stability in storage-ring-based free-electron lasers. We propose a conceptual design, which uses two straight sections to seed coherent extreme-ultraviolet (EUV) and soft X-ray emission with nearly MHz repetition rate. To take the large energy spread (10 –3 ) of a storage ring into account and utilize the existing bending magnets between the two straight sections as the first chicane, we implement a special modeling tool, named EEHG optimizer. This tool has been successfully applied to maximize the prebunching with a reasonably low energy modulation, thereby generating intense coherent X-ray pulses within a short undulator length (a few meters) limited by the available space of a storage ring. Numerical simulations confirm that the optimized EEHG parameters can be directly applied to generate a 10 MW scale peak power with fully coherent ultrafast EUV to soft X-ray pulses based on the NSLS-II parameters. This method can be easily extended to other types of diffraction-limited storage rings.
36 MATERIALS SCIENCE↗
Spin-phonon resonances in nearly polar metals with spin-orbit coupling
In metals in the vicinity of a polar transition, interactions between electrons and soft phonon modes remain to be determined. Here we explore the consequences of spin-orbit assisted electron-phonon coupling on the collective modes of such nearly polar metals in the presence of magnetic field. We find that the soft polar phonon hybridizes with spin-flip electronic excitations of the Zeeman-split bands leading to an anticrossing. The associated energy splitting allows for an unambiguous determination of the strength of the spin-orbit mediated coupling to soft modes in polar metals by spectroscopic experiments. Here, the approach to the polar transition is reflected by the softening of the effective g factor of the hybridized spin-flip mode. Analyzing the static limit, we find that the polar order parameter can be oriented by magnetic field. This provides possibilities for alternative switching protocols in polar metallic materials. We demonstrate that the effects we predict can be observed with current experimental techniques and discuss promising material candidates.
75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
Design of a Single Layer Metamaterial for Pressure Offloading of Transtibial Amputees
While using a prosthesis, transtibial amputees may experience pain and discomfort brought on by large pressure gradients at the interface between the residual limb and prosthetic socket. Current prosthetic interface solutions attempt to alleviate these pressure gradients by using soft homogenous liners to reduce and distribute pressures. This research investigates an additively manufactured metamaterial inlay with a tailored mechanical response to reduce peak pressure gradients around the limb. The inlay uses a hyperelastic behaving metamaterial (US10244818) comprised of triangular pattern unit cells which can be 3D printed with walls of various thicknesses controlled by draft angles. The hyperelastic material properties are modeled using a Yeoh 3rd order model. The 3rd order coefficients can be adjusted and optimized, which corresponds to a change in the unit cell wall thickness to create an inlay that can meet the unique offloading needs of an amputee. Finite element analysis simulations evaluated the pressure gradient reduction from: 1) a common homogenous silicone liner, 2) a prosthetist's inlay prescription that utilizes three variations of the metamaterial, and 3) a metamaterial solution with optimized Yeoh 3rd order coefficients. When compared to a traditional homogenous silicone liner for two unique limb loading scenarios, the prosthetist prescribed inlay and the optimized material inlay can achieve equal or greater pressure gradient reduction capabilities. These results show the potential feasibility of implementing this metamaterial as a method of personalized medicine for transtibial amputees by creating a customizable interface solution to meet the unique performance needs of an individual patient.
60 APPLIED LIFE SCIENCES↗
High Pressure and Two-Sided Mold Surface Solutions (CRADA Final Report)
This project provided surface solutions for highly loaded precision tooling relevant to the automotive industry. Previous development work in coatings for Big Area Additive Manufacturing (BAAM) has produced commercialized coatings for low temperature Acrylonitrile Butadiene Styrene (ABS) tools (TD Coat RT) as well as a soft coating for high temperature applications (TD Seal HT). The team developed these coatings and commercialized them during a prior Manufacturing Demonstration Facility (MDF) technical collaboration (NFE-15-05793). During the prior collaboration, commercialization testing was successfully performed by the Boeing and NAVAIR and resulted in an Awards for Composites Excellence (ACE), award at CAMX – The Composites and Advanced Materials Expo 2016. While this work was clearly successful, gaps in the technology were identified, that prevent widespread adoption of large-scale additive manufacturing in high pressure tooling applications prevalent in the automotive industry. In this project we focused on development of surface solutions for two-sided, compression molding tooling printed on a large-scale polymer AM system in an arbitrary build orientation. We have printed a single cavity extrusion compression molding mold using Polyphenylene sulfide/carbon fiber (PPS/CF) materials, 50% by weight CF samples. These processes are commonly used by Original Equipment Manufacturers (OEM) and Tier 1 suppliers for high volume automotive applications. Several OEMs have identified the need for such technology, indicating significant time and monetary savings could be possible if commercially available surface solutions for high pressure Additive Manufacturing (AM) tooling existed.
36 MATERIALS SCIENCE↗
Metal–Ligand Based Mechanophores Enhance Both Mechanical Robustness and Electronic Performance of Polymer Semiconductors
The backbone of diketopyrrolopyrrole-thiophene-vinylene-thiophene-based polymer semiconductors (PSCs) is modified with pyridine (Py) or bipyridine ligands to complex Fe(II) metal centers, allowing the metal–ligand complexes to act as mechanophores and dynamically crosslink the polymer chains. Here, mono- and bi-dentate ligands are observed to exhibit different degrees of bond strengths, which subsequently affect the mechanical properties of these Wolf-type-II metallopolymers. The counter ion also plays a crucial role, as it is observed that Py-Fe mechanophores with non-coordinating BPh 4 – counter ions (Py-FeB) exhibit better thin film ductility with lower elastic modulus, as compared to the coordinating chloro ligands (Py-FeC). Interestingly, besides mechanical robustness, the electrical charge carrier mobility can also be enhanced concurrently when incorporating Py-FeB mechanophores in PSCs. This is a unique observation among stretchable PSCs, especially that most reports to date describe a decreased mobility when the stretchability is improved. Next, it is determined that improvements to both mobility and stretchability are correlated to the solid-state molecular ordering and dynamics of coordination bonds under strain, as elucidated via techniques of grazing-incidence X-ray diffraction and X-ray absorption spectroscopy techniques, respectively. This study provides a viable approach to enhance both the mechanical and the electronic performance of polymer-based soft devices.
36 MATERIALS SCIENCE↗
Identifying Topological Defects in Lamellar Phases through Contour Analysis of Complex Wave Fields
Lamellar phases frequently contain structural imperfections that significantly affect their behaviors and properties. Our previous research successfully reconstructed real-space configurations of defective lamellar phases from diffuse scattering patterns, indicating the presence of phase vortices as a potential method for identifying topological defects disrupting the smectic ordering. Here, this report presents a mathematical framework using regularized wave fields to represent defective lamellar structures in real space. Phase singularities, resulting from the interference of random waves and indicating lamellar order disruption, are identified through a contour integral. These wave fields, derived from coherent scattering in reciprocal space, were validated via computational benchmarks analyzing small-angle neutron scattering data from AOT surfactant solutions, facilitating further statistical analysis of the defects. Our study highlights the potential to extract meaningful information about topological defects in lyotropic phases by inversely analyzing experimentally measured two-point static correlations. Our method allows for detailed structural analysis of various lyotropic phases, both particulate and nonparticulate, in their quiescent states and facilitates quantitative investigation of defects’ role in phase transitions. By integrating small-angle scattering, deep learning, and vortex tangle analysis, our comprehensive approach shows promise in addressing complex challenges in the structural analysis of soft matter systems.
36 MATERIALS SCIENCE↗
Sensitive Thermochromic Behavior of InSeI, a Highly Anisotropic and Tubular 1D van der Waals Crystal
Thermochromism, the change in color of a material with temperature, is the fundamental basis of optical thermometry. A longstanding challenge in realizing sensitive optical thermometers for widespread use is identifying materials with pronounced thermometric optical performance in the visible range. Herein, it is demonstrated that single crystals of indium selenium iodide (InSeI), a 1D van der Waals (vdW) solid consisting of weakly bound helical chains, exhibit considerable visible range thermochromism. A strong temperature-dependent optical band edge absorption shift ranging from 450 to 530 nm (2.8 to 2.3 eV) over a 380 K temperature range with an experimental (dE g /dT) max value extracted to be 1.26 × 10 −3 eV K −1 is shown. This value lies appreciably above most dense conventional semiconductors in the visible range and is comparable to soft lattice solids. The authors further seek to understand the origin of this unusually sensitive thermochromic behavior and find that it arises from strong electron–phonon interactions and anharmonic phonons that significantly broaden band edges and lower the E g with increasing temperature. The identification of structural signatures resulting in sensitive thermochromism in 1D vdW crystals opens avenues in discovering low-dimensional solids with strong temperature-dependent optical responses across broad spectral windows, dimensionalities, and size regimes.
36 MATERIALS SCIENCE↗