Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Signal processing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Design guidelines for SAR digital receiver/exciter boards.

High resolution radar systems generally require combining fast analog to digital converters and digital to analog converters with very high performance digital signal processing logic. These mixed analog and digital printed circuit boards present special challenges with respect to electromagnetic interference. This document first describes the mechanisms of interference on such boards then follows up with a discussion of prevention techniques and finally provides a checklist for designers to help avoid common mistakes.

Dudley, Peter A.↗

Feasibility of antenna-to-antenna isolation measurements at S-band in the Facility for Antenna and Radar-cross-section Measurements (FARM)

Frequency-domain antenna-coupling measurements performed in the compact-range room of the FARM, will actually be dominated by reflected components from the ceiling, floor, walls, etc., not the direct freespace coupling. Consequently, signal processing must be applied to the frequency-domain data to extract the direct free-space coupling. The analysis presented above demonstrates that it is possible to do so successfully.

47 OTHER INSTRUMENTATION↗

Real-Time Wavelength Discrimination for Improved Neutron Discrimination in CLYC

We investigated the effects of optical filters on the pulse shape discrimination properties of Cs 2 LiYCl 6 :Ce (CLYC) scintillator crystals. By viewing the scintillation light through various optical filters, we attempted to better distinguish between neutron and gamma ray events in the crystal. We applied commercial interference and colored glass filters in addition to fabricating quantum dot (QD) filters by suspending QDs in plastic films and glass. QD filters ultimately failed because of instability of the QDs with respect to oxidation when exposed to ambient air, and the tendency of the QDs to aggregate in the plastic. Of the commercial filters, the best results were obtained with a bandpass interference filter covering the spectral region containing core-valence luminescence (CVL) light. However, the PSD response of filtered CLYC light was always poorer than the response exhibited by unfiltered light because filters always reduced the amount of light available for signal processing.

36 MATERIALS SCIENCE↗

Radiation-Hardened Circuitry Using Mask-Programmable Analog Arrays (September 2014 Milestone Report)

This is a report of the activities involving Task 2 of the NEET 2 project Radiation Hardened Circuitry Using Mask-Programmable Analog Arrays. Using the analog blocks available in our currently pre-configured Via-Configured Array (VCA), we will perform a detailed schematic design of our system to include the signal-processing blocks for temperature, radiation and pressure. Control and data acquisition will be implemented with the Spartan-6 Field-Programmable Gate Array (FPGA) as well as wired serial communications with a remote computer to be used with this project. In addition, batteries and associated voltage regulators will be selected for powering the system. Fabrication may include a polyimide, printed circuit board (PCB) for improved radiation and temperature tolerance. The PCB will go through a layout process by one of the organizations we utilize for this function and be fabricated by another external vendor. Population of the system board will be performed using one of our in-house technicians or an outside vendor we commonly use. Five prototype systems (sensors, electronics board, battery power supply, and personal computer (PC) serial communications port) will be constructed to support the testing objectives of this work. Quality assurance will be performed at each step by both the submitters and the vendors.

36 MATERIALS SCIENCE↗

Evaluating Moving Target Defense with PLADD

This project evaluates the effectiveness of moving target defense (MTD) techniques using a new game we have designed, called PLADD, inspired by the game FlipIt. PLADD extends FlipIt by incorporating what we believe are key MTD concepts. We have analyzed PLADD and proven the existence of a defender strategy that pushes a rational attacker out of the game, demonstrated how limited the strategies available to an attacker are in PLADD, and derived analytic expressions for the expected utility of the game’s players in multiple game variants. We have created an algorithm for finding a defender’s optimal PLADD strategy. We show that in the special case of achieving deterrence in PLADD, MTD is not always cost effective and that its optimal deployment may shift abruptly from not using MTD at all to using it as aggressively as possible. We believe our effort provides basic, fundamental insights into the use of MTD, but conclude that a truly practical analysis requires model selection and calibration based on real scenarios and empirical data. We propose several avenues for further inquiry, including (1) agents with adaptive capabilities more reflective of real world adversaries, (2) the presence of multiple, heterogeneous adversaries, (3) computational game theory-based approaches such as coevolution to allow scaling to the real world beyond the limitations of analytical analysis and classical game theory, (4) mapping the game to real-world scenarios, (5) taking player risk into account when designing a strategy (in addition to expected payoff), (6) improving our understanding of the dynamic nature of MTD-inspired games by using a martingale representation, defensive forecasting, and techniques from signal processing, and (7) using adversarial games to develop inherently resilient cyber systems.

45 MILITARY TECHNOLOGY, WEAPONRY, AND NATIONAL DEF↗

Load Control System Reliability

This report summarizes the results of the Load Control System Reliability project (DOE Award DE-FC26-06NT42750). The original grant was awarded to Montana Tech April 2006. Follow-on DOE awards and expansions to the project scope occurred August 2007, January 2009, April 2011, and April 2013. In addition to the DOE monies, the project also consisted of matching funds from the states of Montana and Wyoming. Project participants included Montana Tech; the University of Wyoming; Montana State University; NorthWestern Energy, Inc., and MSE. Research focused on two areas: real-time power-system load control methodologies; and, power-system measurement-based stability-assessment operation and control tools. The majority of effort was focused on area 2. Results from the research includes: development of fundamental power-system dynamic concepts, control schemes, and signal-processing algorithms; many papers (including two prize papers) in leading journals and conferences and leadership of IEEE activities; one patent; participation in major actual-system testing in the western North American power system; prototype power-system operation and control software installed and tested at three major North American control centers; and, the incubation of a new commercial-grade operation and control software tool. Work under this grant certainly supported the DOE-OE goals in the area of “Real Time Grid Reliability Management.”

29 ENERGY PLANNING, POLICY, AND ECONOMY↗

Video Analysis in Multi-Intelligence

This is a project which was performed by a graduated high school student at Los Alamos National Laboratory (LANL). The goal of the Multi-intelligence (MINT) project is to determine the state of a facility from multiple data streams. The data streams are indirect observations. The researcher is using DARHT (Dual-Axis Radiographic Hydrodynamic Test Facility) as a proof of concept. In summary, videos from the DARHT facility contain a rich amount of information. Distribution of car activity can inform us about the state of the facility. Counting large vehicles shows promise as another feature for identifying the state of operations. Signal processing techniques are limited by the low resolution and compression of the videos. We are working on integrating these features with features obtained from other data streams to contribute to the MINT project. Future work can pursue other observations, such as when the gate is functioning or non-functioning.

97 MATHEMATICS AND COMPUTING↗

Search for New Physics in Neutral Kaon Decays

This report will summarize contributions made by the ASU group during the grant period. Focus will be given to three areas: (1) Monte Carlo simulations; (2) signal processing in the electronics; and (3) data analysis software. For reference, a drawing of the KOTO detector is shown in Fig. 1. The production target for the neutral beam particles was about 20 meters upstream of the detector.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Detectability prediction for a thermoacoustic sensor in the breazeale nuclear reactor pool

Laboratory experiments have suggested that thermoacoustic engines can be in- corporated within nuclear fuel rods. Such engines would radiate sounds that could be used to measure and acoustically-telemeter information about the op- eration of the nuclear reactor (e.g., coolant temperature or uxes of neutrons or other energetic particles) or the physical condition of the nuclear fuel itself (e.g., changes in temperature, evolved gases) that are encoded as the frequency and/or amplitude of the radiated sound [IEEE Measurement and Instrumen- tation 16(3), 18-25 (2013)]. For such acoustic information to be detectable, it is important to characterize the vibroacoustical environments within reactors. Measurements will be presented of the background noise spectra (with and with- out coolant pumps) and reverberation times within the 70,000 gallon pool that cools and shields the fuel in the 1 MW research reactor on Penn State's campus using two hydrophones, a piezoelectric projector, and an accelerometer. Sev- eral signal-processing techniques will be demonstrated to enhance the measured results. Background vibrational measurement were also taken at the 250 MW Advanced Test Reactor, located at the Idaho National Laboratory, using ac- celerometers mounted outside the reactor's pressure vessel and on plumbing will also be presented. The detectability predictions made in the thesis were validated in September 2015 using a nuclear ssion-heated thermoacoustic sensor that was placed in the core of the Breazeale Nuclear Reactor on Penn State's campus. Some features of the thermoacoustic device used in that experiment will also be revealed. [Work supported by the U.S. Department of Energy.]

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

IoGET: Internet of Geophysical and Environmental Things

The objective of this project is to provide novel and fast reduced-order models for onboard computation at sensor nodes for real-time analysis. The approach will require that LANL perform high-fidelity numerical simulations, construct simple reduced-order models (ROMs) using machine learning and signal processing algorithms, and use real-time data analysis for ROMs and compressive sensing at sensor nodes.

54 ENVIRONMENTAL SCIENCES↗

Data Link Summary for Peer Review.

New generations of high-temperature (HT) sensors and electronics are enabling increased measurement speed and accuracy allowing collection of more accurate and relevant data by downhole tools. Unfortunately, this increased capability is often not realized due to the bottleneck in the uplink data transmission rates due to poor signal characteristics of HT wireline. The objective of this project is to enable the high transmission rate of raw data from downhole tools such as acoustic logging tools and seismic measurement devices to minimize the need for downhole signal processing. To achieve this objective, Sandia has undertaken the effort to develop an asymmetric high-temperature (HT), highspeed data link system for downhole tools capable of operating at temperatures of 210°C while taking advantage of existing wireline transmission channels. Current data rates over HT single-conductor wireline are limited to approximately 200 kbps. The goal system will be capable of transmitting data from the tool to the surface (uplink) at rates of > 1Mbps over 5,000 feet of single-conductor wireline as well as automatically adapt the data rate to the longer wirelines by adapting modern telecommunications techniques to operate on high temperature electronics. The data rate from the surface to the tool (downlink) will be significantly smaller but sufficient for command and control functions. While 5,000 feet of cable is the benchmark for this effort, improvements apply to all lengths of cable.

47 OTHER INSTRUMENTATION↗

Power System Oscillatory Behaviors: Sources, Characteristics, & Analyses

This document is intended to provide a broad overview of the sources, characteristics, and analyses of natural and forced oscillatory behaviors in power systems. These aspects are necessarily linked. Oscillations appear in measurements with distinguishing characteristics derived from the oscillation’s source. These characteristics determine which analysis methods can be appropriately applied, and the results from these analyses can only be interpreted correctly with an understanding of the oscillation’s origin. To describe oscillations both at their source within a physical power system and within measurements, a perspective from the boundary between power system and signal processing theory has been adopted.

24 POWER TRANSMISSION AND DISTRIBUTION↗

HEP Software Foundation Community White Paper Working Group - Detector Simulation

A working group on detector simulation was formed as part of the high-energy physics (HEP) Software Foundation's initiative to prepare a Community White Paper that describes the main software challenges and opportunities to be faced in the HEP field over the next decade. The working group met over a period of several months in order to review the current status of the Full and Fast simulation applications of HEP experiments and the improvements that will need to be made in order to meet the goals of future HEP experimental programmes. The scope of the topics covered includes the main components of a HEP simulation application, such as MC truth handling, geometry modeling, particle propagation in materials and fields, physics modeling of the interactions of particles with matter, the treatment of pileup and other backgrounds, as well as signal processing and digitisation. The resulting work programme described in this document focuses on the need to improve both the software performance and the physics of detector simulation. The goals are to increase the accuracy of the physics models and expand their applicability to future physics programmes, while achieving large factors in computing performance gains consistent with projections on available computing resources.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

MODAL FREQUENCY TRACKING: Performance Analysis on Noisy Experimental Ground Test Data

Mechanical devices operating in an environment contaminated by noise, uncertainties, and extraneous disturbances lead to low signal-to-noise-ratios creating an extremely challenging signal processing problem—especially for on-line, realtime, in-flight application. In this report, we discuss a model-based approach to incorporate physical device features into a dynamic structure that can be used to perform on-line tracking of modal frequencies. The approach we take, after pre-processing the raw measurement data, is to obtain a representation of the structural device under test that captures its underlying response to a suite of excitations and operating conditions. One approach is to apply modern system identification techniques based on stochastic subspace methods capable of both: (1) identifying the underlying black-box structure enabling the extraction of structural modes that can be used for analysis; and (2) modal tracking under continued vibrational excitation as in a real-time, in-flight like environment. The vibrational signature of the structural device is measured directly using a suite of tri-axial accelerometers characterizing a multiple input/multiple output (MIMO) dynamic system. In this analysis, we have 15 tri-axial accelerometer measurements or 45 total output channels along with a single excitation also measured with a tri-axial accelerometer providing a 3-input system for processing. We initially describe the experiment and then briefly develop the necessary background in stochastic subspace realization, discuss the algorithm and apply it to the isolated structural device, first, characterized by the set of noisy MIMO accelerometer measurements extracting the modal model from the data (subspace identification), extract the unique modal frequencies (modal coordinate transformation), track their evolution (real-time tracker) to evaluate the overall performance of the processor. Next we evaluate processor performance when the structural device is incorporated into a flight vehicle for further performance analysis. We summarize the results and predict performance.

42 ENGINEERING↗

Final Report: Mapping Fracture Network Creation with Microseismicity During EGS Demonstrations

Effective enhanced geothermal system (EGS) sites require optimal fracture networks for efficient heat transfer between hot rock and fluids. Microseismic mapping is a key tool used to infer the subsurface fracture geometry and is widely used in the petroleum industry to monitor fracture propagation during hydraulic stimulations. Traditional earthquake detection techniques (e.g. STA/LTA detectors) and location techniques are often employed to identify microearthquakes in geothermal regions. However, most commonly used algorithms may miss events if the seismic signal of an earthquake is small relative to the background noise level or if a microearthquake occurs within the coda of a larger event. Consequently, we have developed a set of algorithms that provide improved microearthquake detection even in difficult signal processing environments.

58 GEOSCIENCES↗

High Density Chip Interconnect Technology Using High Density Glass Interposers

Demands for high density and high speed interconnect solutions are not satisfied by current technology offerings. Platforms such as printed circuit boards (PCBs), ceramic substrates and silicon interposers don’t provide the small form factor nor the I/O density to support 5G or 1Tbps gigabit ethernet solutions. Current solutions also don’t support die to die assembly with integrated tiled solutions for wide area and fanout solutions for lager data and signal processing. A solution with through vias provides an order of magnitude or smaller density supporting much higher density attach and assembly By fabricating a very fine pitch metal filled through glass via solution it’s possible to deliver the necessary improvements in performance, reliability, even higher data speed rates with smaller area and much denser geometries. There are a number of opportunities across a wide variety of industries for through glass interposers as they become the replacement for printed circuit boards (PCBs) and ceramic substrates. The broad array of opportunities include renewable energy, medical electronics (ME), defense electronics (DE)/space and consumer electronics (CE), but likely will impact every industry and market segment. Compared to PCBs, through glass via (TGV) solutions provide the next generation platform for semiconductor assembly improvements. The ability to generate lines, spaces, trenches and vias similar to wafer level geometries delivers wired solutions one to two orders of magnitude smaller than traditional organic PCB and ceramic substrate offerings. Higher density connections also include the thru vias that connect multiple metal layers, fanout. It’s possible to deliver filled metal vias that are 20um diameter with much tighter pitch than can be offered with PCB. Our goal is to provide 20um diameter and smaller via, 50um and smaller pitch, and aspect ratios at 25:1 and greater with hermetically metal filled vias. The goal of CVI is to replace or eliminate PCBs, ceramic substrate and through silicon vias (TSV) providing a glass interposer with metal filled, fiber plugged and/or optional wireless interconnectivity. The end plan is to deliver a glass substrate platform that provides improved electrical performance, versatility, inertness, and much improved cost and cycle time (development, drawing, and delivery) to performance in the form of small millimeter sized substrates or full 8” wafer substrates. Glass delivers an improvement over silicon thru vias (TSV) in the number of processing steps, cost, reliability and cycle time. In addition to metal plugged vias, our glass interposers are capable of fiber and antennae solutions providing two additional very high density and ultra-high speed data transfer capabilities.

36 MATERIALS SCIENCE↗

NSLS-II: Turn-by-Turn BPM Data Analysis – A Use Case Approach

A modern ring-based light source is a complex dynamic system for which the design is guided by a realistic computer model with predictable results. State-of-the-arts beam requirements translate into tight engineering tolerances. So, quality assurance for the equipment, e.g. ring magnets, girder system, power supplies, RF system, etc. is crucial to deliver on the design goals for the beam quality. For a streamlined commissioning and an effective approach for integration of insertion devices, the latter being an activity that is typically on-going for the entire life cycle of the facility, it is equally important to be able to calibrate the beam dynamics design model against the real system and pursue e.g. “gap analysis”, linear and nonlinear optics corrections, improvements to the baseline design, etc. In particular, for high-end insertion devices. Conceptually, it can be thought of as pursuing Model-Based and Adaptive Control; instead of “flying blind”. A straightforward approach is to use a pinger, a ~30 cm long hor/ver kicker that can kick the beam to about 1 mrad in each plane [1-2] and a Turn-by-Turn BPM data acquisition system that records the betatron motion on a Turn-by-Turn basis. Examples include: ALS, SLS, DIAMOND, and SOLEIL. We first outline how to measure the Beam Impulse Response (BIR) function and related Beam Transfer Function (BTF) with a Turn-by-Turn BPM data acquisition system and a pinger. In particular, how to obtain the amplitude and phase of the spectral components in the betatron spectrum with high precision by using signal processing. We also quantify how the impact of noise affects the accuracy of the measurements.

97 MATHEMATICS AND COMPUTING↗

Modal Frequency Identification of a Cylindrical Object from Noisy Vibrational Response Measurements

The investigation of the vibrational response of a cylindrical object in a noisy environment (a pipe in air) to impact excitations provided by a cam-driven, hammer-like surface, randomly excited by an electric motor is of high interest—especially when potential anomalies can occur. This project encompasses all of the components from modeling to validation to controlled testing and signal processing in order develop a real-time system capable of on-board performance and monitoring.

42 ENGINEERING↗