Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Shear deformation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2022

Microstructures and deformation mechanisms of the medium-entropy alloy (NiCoCr) 76 (Ni 6 AlTi) 3

Here the microstructures and deformation mechanisms of the f.c.c. medium-entropy alloy (MEA) (NiCoCr) 76 (Ni 6 AlTi) 3 has been analyzed after various thermo-mechanical treatments. The solutionized, single-phase MEA, which had a grain size of 93.4 ± 31.9 μm, was cold-rolled (CR) to a 80% thickness reduction after which it showed both a high yield strength (YS) of 1539 MPa and a high ultimate tensile strength (UTS) of 1602 MPa, but an elongation to failure, ε, of only 16%. The CR MEA was then subjected to one of two heat treatments: (1) the CR MEA was recrystallized at 1100°C for 24 h, which produced a single-phase material with 85 ± 61.7 μm grain size that exhibited a much lower YS and UTS of 364 MPa and 747 MPa, respectively, but a much greater ε of 73%; and (2) the MEA was aged at 700°C for 24 h, which produced a fine-grained (1.1 ± 0.9 μm) material and a high volume fraction (0.35) of 12 nm dia. L1 2 nanoparticles that exhibited an excellent combination of strength and ductility, viz., YS~1501 MPa, UTS~1651 MPa, elongation ~26%. The grain boundary strengthening and precipitation strengthening were together estimated to account for ~58% of the YS in the latter material. After deformation, the recrystallized MEA contained numerous stacking faults and a Taylor lattice structure containing domain boundaries and microbands, while the aged MEA exhibited numerous stacking faults and sheared particles. The density of low-angle grain boundaries (LAGBs) in the recrystallized MEA increased by 100 times to 2.2 × 10 –1 μm/μm 2 while the density of CSL Σ3 n boundaries decreased by 71% to 7.8 × 10 –3 μm/μm 2 after deformation. In contrast, the density of LAGBs in the aged MEA increased by 5 times to 2.6 μm/μm 2 while the density of CSL Σ3 n boundaries decreased by 57% to 0.6 μm/μm 2 after deformation.

36 MATERIALS SCIENCE↗
DOE OSTI2024

High‐Temperature Mechanical Behavior of Single‐Crystal FeCrAl Alloy Under In Situ Micropillar Compression

FeCrAl cladding is one of the candidate materials for the near‐term accident‐tolerant fuel technologies under development. Research on high‐temperature mechanical behaviors of single‐crystal FeCrAl alloy is rather limited. Previous studies have reported the mechanical property of low‐index orientation in single‐crystal FeCrAl alloy at room temperature. However, the critical resolved shear stress to activate slip systems can be orientation and temperature dependent. Here, single‐crystal grains in a coarse‐grained FeCrAl alloy with different crystallographic orientations are selected to preferentially activate {110}<111> slip systems or {112}<111> slip systems. Micropillars are fabricated in the selected single‐crystal grains and tested at elevated temperatures in situ in a scanning electron microscope. The critical resolved shear stresses of {110}<111> slip systems and {112}<111> slip systems are determined at various temperatures. The critical resolved shear stress shows a temperature dependence and orientation independence. This study provides important insight for understanding the deformation mechanisms of FeCrAl alloys at elevated temperatures.

Sun, Tianyi↗
DOE OSTI2025

Droplet breakup by multimodal nonlinear Rayleigh Taylor instability

A droplet impacted by a shock wave will undergo a process of fragmentation due to the development of interfacial hydrodynamic instabilities. The interface experiences variable acceleration and shear that result in the development of both inertial (Rayleigh–Taylor) and shear (Kelvin–Helmholtz) instabilities. These perturbations grow in time and drive the fragmentation and breakup of the deformed droplet. Experiments are performed on nominally 0.86 mm water droplet subjected to a Mach 7.6 detonation wave, resulting in a high Weber number (~36,000) breakup event. Perturbation growth is measured from a series of high-speed (> MHz) shadowgraph images. It is proposed that, given the size of the large-scale perturbations observed in experiments, these instabilities are growing in the non-linear regime and can be described by bubble-merger models for nonlinear mixing. Calculations are performed for the growth rates and size of these instabilities using deformation and external flow models to establish the time-dependent boundary conditions. The concurrence of the measured perturbation widths and the predictions of the simple model lend credence to the theory. This novel approach serves to open a new avenue in the characterization of droplet breakup via hydrodynamic instabilities.

Droplet breakup↗
DOE OSTI2020

Dislocation density-based plasticity model from massive discrete dislocation dynamics database

In this work, we present a dislocation density-based strain hardening model for single crystal copper through a systematic coarse-graining analysis of more than 200 discrete dislocation dynamics (DDD) simulations of plastic deformation under uniaxial tension. The proposed constitutive model has two components: a generalized Taylor relation connecting resolved shear stresses to dislocation densities on individual slip systems, and a generalized Kocks-Mecking model for dislocation multiplication. The DDD data strongly suggests a logarithmic dependence of flow stress on the plastic shear strain rate on each slip system, and, equivalently, an exponential dependence of the plastic shear strain rate on the resolved shear stress. Hence the proposed generalized Taylor relation subsumes the Orowan relation for plastic flow. The DDD data also calls for a correction to the Kocks-Mecking model of dislocation multiplication to account for the increase of dislocation density on slip systems with negligible plastic shear strain rate. This is accomplished by allowing the multiplication rate on each slip system to include contributions from the plastic strain rates of the two coplanar slip systems. The resulting constitutive model successfully captures the strain hardening rate dependence on the loading orientation as predicted by the DDD simulations, which is also consistent with existing experiments.

36 MATERIALS SCIENCE↗
NASA NTRS1976

Micromechanics of slip bands on a free surface

A micromechanics analysis for the formation and propagation of slip bands on the free surface of a polycrystal under monotonic loading is presented. For the growth of slip bands, the analysis satisfies the conditions of both equilibrium and displacement continuity, as well as the relation between slip and the resolved shear stress throughout the polycrystal. Numerical calculations show how the microstress field causes the concentration of plastic deformation in discrete sliding bands and give results which are in good qualitative agreement with known slip band observations on aluminum single crystals.

Lin, S. R.↗
NASA NTRS1984

Influence of cobalt, tantaum and tungsten on the high temperature mechanical properties of single crystal nickel-base superalloys

For alloys with the baseline refractory metal level of 3 percent Ta and 10 percent W, decreases in Co level from 10 to 0 percent resulted in increased tensile strength and creep resistance. Substitution of W for Ta resulted in decreased creep life at high stresses but improved life at low stresses. Substitution of Ni for Ta caused large reductions in tensile strength and creep resistance, and corresponding increases in ductility. For these alloys with low Ta plus W totals, strength was independent of Co level. The increases in tensile strength with increases in refractory metal content were related to the increases in gamma volume fraction and solid solution hardening. Increases in strength as Co level decreased were considered to be the result of coherency strain hardening from the increased lattice mismatch. Dislocation shear through the gamma-gamma interface is considered to be the rate limiting step in the deformation process.

Nathal, M. V.↗
NASA NTRS1985

Evolution of a curved vortex filament into a vortex ring

The deformation of a hairpin-shaped vortex filament under self-induction and in the presence of shear is studied numerically using the Biot-Savart law. It is shown that the tip region of an elongated hairpin vortex evolves into a vortex ring and that the presence of mean shear impedes the process. Evolution of a finite-thickness vortex sheet under self-induction is also investigated using the Navier-Stokes equations. The layer evolves into a hairpin vortex which in turn produces a vortex ring of high Reynolds stress content. These results indicate a mechanism for the generation of ring vortices in turbulent shear flows, and a link between the experimental and numerical observation of hairpin vortices and the observation of ring vortices in the outer regions of turbulent boundary layers.

Moin, P.↗
NASA NTRS1986

Evolution of a curved vortex filament into a vortex ring

The deformation of a hairpin-shaped vortex filament under self-induction and in the presence of shear is studied numerically using the Biot-Savart law. It is shown that the tip region of an elongated hairpin vortex evolves into a vortex ring and that the presence of mean shear impedes the process. Evolution of a finite-thickness vortex sheet under self-induction is also investigated using the Navier-Stokes equations. The layer evolves into a hairpin vortex which in turn produces a vortex ring of high Reynolds stress content. These results indicate a mechanism for the generation of ring vortices in turbulent shear flows, and a link between the experimental and numerical observation of hairpin vortices and the observation of ring vortices in the outer regions of turbulent boundary layers.

Moin, P.↗
NASA NTRS2001

Osteoblasts respond to pulsatile fluid flow with short-term increases in PGE(2) but no change in mineralization

Although there is no consensus as to the precise nature of the mechanostimulatory signals imparted to the bone cells during remodeling, it has been postulated that deformation-induced fluid flow plays a role in the mechanotransduction pathway. In vitro, osteoblasts respond to fluid shear stress with an increase in PGE(2) production; however, the long-term effects of fluid shear stress on cell proliferation and differentiation have not been examined. The goal of this study was to apply continuous pulsatile fluid shear stresses to osteoblasts and determine whether the initial production of PGE(2) is associated with long-term biochemical changes. The acute response of bone cells to a pulsatile fluid shear stress (0.6 +/- 0.5 Pa, 3.0 Hz) was characterized by a transient fourfold increase in PGE(2) production. After 7 days of static culture (0 dyn/cm(2)) or low (0.06 +/- 0.05 Pa, 0.3 Hz) or high (0.6 +/- 0.5 Pa, 3.0 Hz) levels of pulsatile fluid shear stress, the bone cells responded with an 83% average increase in cell number, but no statistical difference (P > 0.53) between the groups was observed. Alkaline phosphatase activity per cell decreased in the static cultures but not in the low- or high-flow groups. Mineralization was also unaffected by the different levels of applied shear stress. Our results indicate that short-term changes in PGE(2) levels caused by pulsatile fluid flow are not associated with long-term changes in proliferation or mineralization of bone cells.

NASA Discipline Musculoskeletal↗
NASA NTRS1980

Extensional flow of dilute polymer solution

Simultaneous effects of temperature and concentration on tensile viscosity are investigated using a semi-empirical scaling law established to relate the concentration, temperature and deformation rate by a reduced deformation rate variable. Results show the onset of high viscosity occurring in the vicinity of the onset of non-Newtonian viscosity observed in a simple shear flow experiment. High viscosity is also compared with steady and dynamic shear data. Finally, the asymptotic solution of Hassager's kinetic theory of a bead-rod model for macromolecular solutions is compared with the data, indicating that tensile viscosity depends strongly on the molecular weight, the higher the molecular weight, the more sensitive the tensile viscosity in terms of the deformation rate.

Peng, S. T. J.↗
NASA NTRS1992

Postbuckling failure of composite plates with central holes

The postbuckling failure of square composite plates with central holes is analyzed numerically and experimentally. The particular plates studies have stacking sequences of: (+ and - 45/0/90)(sub 2S); (+ and - 45/0(sub 2))(sub 2S); (+ and - 45/0(sub 6))(sub S); and (+ and - 45)(sub 4S). A simple plate geometry, one with a hole diameter to plate width ratio of 0.3 is compared. Failure load, failure mode, and failure location are predicted numerically by using the finite element method. Predictions are compared with experimental results. In numerical failure analysis the interlaminar shear stresses, as well as the inplane stresses are taken into account. An issue addressed in this study is the possible mode shape change of the plate during loading. It is predicted that the first three laminates fail due to excessive stresses in the fiber direction, and more importantly, that the load level is independent of whether the laminate is deformed in a one-half or two-half wave configuration. It is predicted that the fourth laminate fails due to excessive inplane shear stress. Interlaminar shear failure is not predicted for any laminates. For the first two laminates the experimental observations correlated well with the predictions. Experimentally, the third laminate failed along the side support due to interlaminar shear strength S(sub 23). The fourth experimental laminate failed due to inplane shear in the location predicted, however material softening resulted in a different failure load from predictions.

Lee, H. H.↗
DOE OSTI2020

Crystallographic orientation-dependent strain hardening in a precipitation-strengthened Al-Cu alloy

While the strengthening of Al-Cu alloys due to precipitation has been extensively studied, the effect of crystallographic orientation of the matrix and precipitates, as well as precipitate morphology, on the strain hardening behavior is not well understood. In this paper, we investigate this effect with in situ neutron diffraction during deformation of an Al-Cu alloy (206) after multiple aging treatments. Precipitate-dislocation interactions were found to change from precipitate shearing for microstructures predominantly containing GPI and θ" precipitates to Orowan looping for microstructures with primarily θ' and θ precipitates. Notably, significant anisotropy in strain hardening behavior was observed when θ' precipitates were present, which was attributed to crystallographic orientation dependent load transfer from the Al matrix to the θ' precipitates. The anisotropic load transfer is hypothesized to be caused by the extent of rotation of high aspect-ratio θ' precipitates, owing to dislocations looping around them during plastic deformation of the matrix. Predictions from an analytical model describing the anisotropic magnitude of load transfer from precipitate rotation agree well with experimental results, successfully validating the precipitate rotation hypothesis and explaining the anisotropic strain hardening behavior. This model allows for the prediction of stresses separately in the precipitate and matrix phases as a function of crystallographic orientation, only given the bulk mechanical properties.

36 MATERIALS SCIENCE↗
NASA NTRS1989

The low cycle fatigue deformation response of a single-crystal superalloy at 650 C

The cyclic stress-strain response and the associated deformation structure of the single crystal nickel-base superalloy PWA 1480 were investigated. Specimens of various crystallographic orientations were tested in low-cycle fatigue (LCF) at 650 C, resulting in a significant tension-compression anisotropy in initial yield strength associated with the shearing of gamma-prime precipitates by dislocation pairs, and a LCF cyclic hardening of the crystals associated with dislocation interactions occurring in the gamma phase. In specimens deforming by slip on a single slip system, dislocations of the primary slip system accumulated in the gamma matrix and formed seesile entanglements. In specimens deforming by slip on several slip systems, the dislocations of the different operative slip systems intersected in the gamma matrix and formed sessile arrangements.

Gabb, T. P.↗
DOE OSTI2021

A Computational Study of the Shear Behavior of Reinforced Concrete Beams Affected from Alkali–Silica Reactivity Damage

In this study, an investigation of the shear behavior of full-scale reinforced concrete (RC) beams affected from alkali–silica reactivity damage is presented. A detailed finite element model (FEM) was developed and validated with data obtained from the experiments using several metrics, including a force–deformation curve, rebar strains, and crack maps and width. The validated FEM was used in a parametric study to investigate the potential impact of alkali–silica reactivity (ASR) degradation on the shear capacity of the beam. Degradations of concrete mechanical properties were correlated with ASR expansion using material test data and implemented in the FEM for different expansions. The finite element (FE) analysis provided a better understanding of the failure mechanism of ASR-affected RC beam and degradation in the capacity as a function of the ASR expansion. The parametric study using the FEM showed 6%, 19%, and 25% reduction in the shear capacity of the beam, respectively, affected from 0.2%, 0.4%, and 0.6% of ASR-induced expansion.

36 MATERIALS SCIENCE↗
NASA NTRS1972

Theoretical study of corrugated plates: Shear stiffness of a trapezoidally corrugated plate with discrete attachments to a rigid flange at the ends of the corrugations

Analysis and numerical results are presented for the elastic shear stiffness of a corrugated shear web with a certain type of discrete attachments at the ends of the trough lines of the corrugations, namely point attachments to a rigid flange which interferes with the deformations of the end cross sections by preventing downward movement but permitting upward (lifting off) movement. The analysis is based on certain assumed modes of deformation of the cross sections in conjunction with the method of minimum total potential energy and the calculus of variations in order to obtain equations for the manner in which the assumed modes of deformation vary along the length of the corrugation. The numerical results are restricted to the case of equal-width crests and troughs but otherwise apply to a wide variety of geometries. They are in the form of graphs which give the overall shear stiffness as a fraction of the overall shear stiffness that could be obtained by having continuous attachment at the ends of the corrugations.

Hsiao, C.↗
DOE OSTI2020

Connecting Dynamic Strain Aging to Deformation Processing in Magnesium-Calcium-Based Alloys

Fuel consumption can be improved by reducing car weight with substitution of aluminum and steel parts with magnesium (Mg). Magnesium formability at room temperature is limited due to strong basal texture generated prior processing. Shear band nucleation, observed under conditions in which dynamic strain aging (DSA), have been attributed to be responsible for texture weakening in dilute Mg – Rare Earths (RE) alloys. A low–cost substitution of RE is calcium (Ca) with similar atomic size. It is hypothesized that deformation of Mg – Ca alloys under DSA conditions improves Mg formability. In this study, Mg–Ca and Mg–Ca–Zn alloys were characterized using optical microscopy, XRD, and SEM/EDS. Compression testing was performed between 200 and 300C at different strain rates to observe DSA behavior. This work was performed under DOE Award Number DE-EE0007756.

Manuel, Michele↗
NASA NTRS1989

Mechanical properties of lunar regolith and lunar soil simulant

Through the Surveyor 3 and 7, and Apollo 11-17 missions a knowledge of the mechanical properties of Lunar regolith were gained. These properties, including material cohesion, friction, in-situ density, grain-size distribution and shape, and porosity, were determined by indirect means of trenching, penetration, and vane shear testing. Several of these properties were shown to be significantly different from those of terrestrial soils, such as an interlocking cohesion and tensile strength formed in the absence of moisture and particle cementation. To characterize the strength and deformation properties of Lunar regolith experiments have been conducted on a lunar soil simulant at various initial densities, fabric arrangements, and composition. These experiments included conventional triaxial compression and extension, direct tension, and combined tension-shear. Experiments have been conducted at low levels of effective confining stress. External conditions such as membrane induced confining stresses, end platten friction and material self weight have been shown to have a dramatic effect on the strength properties at low levels of confining stress. The solution has been to treat these external conditions and the specimen as a full-fledged boundary value problem rather than the idealized elemental cube of mechanics. Centrifuge modeling allows for the study of Lunar soil-structure interaction problems. In recent years centrifuge modeling has become an important tool for modeling processes that are dominated by gravity and for verifying analysis procedures and studying deformation and failure modes. Centrifuge modeling is well established for terrestrial enginering and applies equally as well to Lunar engineering. A brief review of the experiments is presented in graphic and outline form.

Steven W Perkins↗