Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STREAM FUNCTION”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Unconventional desalination: The use of cyclone separators in HDH desalination to achieve zero liquid discharge

Research in water desalination technologies is constantly growing to meet global demands for freshwater. Though acting to meet these demands, the rapid growth and spread of desalination technologies poses environmental issues due to the increasing brine concentrates that are ultimately discharged back to nature. This article presents a cyclone separator to transform a humidification-dehumidification (HDH) cycle to a dual-product cycle to produce freshwater and solid salt crystals for highly saline streams. A desalination cycle equipped with a cyclone separator is used to treat water with 3.5%–81% salinity. The separation efficiency is well above 99% and can produce potable water from hyper saline feed in a once-through process. Further, the cyclone separator performance was tested under different conditions including humidity ratios, relative humidities, and feed stream's salinities. The cyclone separator is self-cleaning and overcomes salt scaling. This behavior is a direct function of the walls' temperature and the carrier air dew point. Self-cleaning capability allows the cyclone separator to treat feed water of extreme salinities (up to 810,000ppm) down to freshwater salinity with zero liquid discharge. The cyclone separator was utilized in a novel HDH desalination technology to treat different salinities. The product was freshwater of salinity <500ppm.

42 ENGINEERING↗

Nonthermal effects on the Buneman instability in Lorentzian dusty plasmas

The nonthermal effects on the Buneman instability due to the ion streaming are investigated in Lorentzian dusty plasmas. The growth rates and frequency of the Buneman instability are obtained as functions of the spectral index of the Lorentzian plasma. It is shown that the nonthermal effect suppresses the growth rates as well as the real frequency term of the unstable root. Hence, the growth rates of the Buneman instability in nonthermal plasmas are found to be always smaller than those in Maxwellian plasmas. It is also found that the nonthermal effects on the growth rates decrease with increasing wave number.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

On the local measurement of electric currents and magnetic fields using Thomson scattering in Weibel-unstable plasmas

Here, we demonstrate the capability of the Thomson Scattering (TS) diagnostic to measure locally the microscopic electron and ion currents in counter-streaming plasmas unstable to the Weibel or current-filamentation instability. Synthetic TS spectra are calculated with particle distribution functions obtained from particle-in-cell simulations and used to accurately reproduce the simulated currents. We show that this technique allows accurate local measurements of the magnetic field, thus opening the way for the complete experimental characterization of the growth rate, saturation, and nonlinear dynamics of electromagnetic instabilities in plasmas. We illustrate the application of this diagnostic to experimental TS data, which yields local measurements of the magnetic field in Weibel-unstable plasmas and indicates that the magnetic energy density reaches ~1% of the kinetic energy density of the flows, in agreement with previous numerical studies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Reinvestigating the clusters Koposov 1 and 2

We investigate the fundamental parameters of age, distance, and mass function slope for the poorly studied clusters Koposov 1 and Koposov 2. These clusters were discovered recently and tentatively classified as globular clusters. Using the Large Monolithic Imager on Lowell Observatory's Discovery Channel Telescope, we present photometry extending to V = 25, three to four magnitudes below the main sequence turnoffs for the clusters. We find the clusters have tidal radii of 15 pc and 10.7 pc and distances of 34.9 kpc and 33.3 kpc for Koposov 1 and Koposov 2, respectively. Studying the stellar content of the clusters, we use completeness-corrected star counts to reveal extremely faint total magnitudes of 2.01 and 0.03 in V, and steep Salpeter-like present-day mass functions. Finally, we show that the spatial positions of the clusters agree well with the position of the Sagittarius stream and conclude that these two objects are open clusters removed from the Sagittarius galaxy.

79 ASTRONOMY AND ASTROPHYSICS↗

IDAES-PSE 2.2.0 Release

The Institute for the Design of Advanced Energy Systems (IDAES) Integrated Platform is a versatile computational environment offering extensive process systems engineering (PSE) capabilities for optimizing the design and operation of complex, interacting technologies and systems. IDAES enables users to efficiently search vast, complex design spaces to discover the lowest cost, most environmentally sustainable solutions while supporting the full process modeling lifecycle, from conceptual design to dynamic optimization and control. The extensible, open platform empowers users to create models of novel processes and rapidly develop custom analyses, workflows, and end-user applications. New features in the 2.2 release include: DiagnosticsToolbox DiagnosticsToolbox (idaes.core.util.model_diagnostics. DiagnosticsToolbox is a new self-guiding toolbox for assisting with diagnosing modeling issues. The toolbox contains a wide range of tools for identifying common modeling issues and conveying these to the user, and more features will be added in the coming months. To try the new toolbox, use the following steps: from idaes.core.util import DiagnosticsToolbox Build an instance of your model Ensure your models has zero degrees of freedom (as best you can) dt = DiagnosticsToolbox(model) dt.report_structural_issues() Follow the prompts Deprecations DegeneracyHunter is being deprecated in favor of the new DiagnosticsToolbox. The features and capabilities of DegeneracyHunter will be moved over to the DiagnositcsToolbox in the coming months. Removal of usage of Pyomo's expr.current due to deprecation upstream. Removed support for radial basis functions in ALAMOpy as these did not work in the current implementation. Those wishing to use radial basis functions should use Pysmo instead. New Capabilities MSContactor model for unit operations involving mass transfer between 2 or more streams, such as membrane, solvent extraction and solids leaching operations. Other Improvements Improved formulation for solubility products with additional parameters for better scaling of terms Better backward compatibility, verification and robustness testing of core models and APIs Added support for Separator models without energy balances

DiagnosticsToolbox↗

Effects of Magnetic Field on the Turbulent Wake of a Cylinder in MHD Channel Flow

Results from a free-surface MHD flow experiment are presented detailing the modi cation of vortices in the wake of a circular cylinder with its axis parallel to the applied magnetic fi eld. Experiments were performed with a Reynolds number near Re ~ 104 as the interaction parameter, N = |j x B| / |ρ (υ • ∇), was increased through unity. By concurrently sampling the downstream fluid velocity at sixteen cross-stream locations in the wake, it was possible to extract an ensemble of azimuthal velocity profi les as a function of radius for vortices shed by the cylinder at varying strengths of magnetic field. Results indicate a signi cant change in vortex radius and rotation as N is increased. The lack of deviations from the vortex velocity pro file at high magnetic fi elds suggests the absence of small-scale turbulent features. By sampling the wake at three locations downstream in subsequent experiments, the decay of the vortices was examined and the effective viscosity was found to decrease as N-049±0.4. This reduction in effective viscosity is due to the modi cation of the small-scale eddies by the magnetic fi eld. The slope of the energy spectrum was observed to change from a k-1.8 power-law at low N to a k-3.5 power-law for N > 1. Together, these results suggest the flow smoothly transitioned to a quasi-two-dimensional state in the range 0 < N < 1.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Video Analysis in Multi-Intelligence

This is a project which was performed by a graduated high school student at Los Alamos National Laboratory (LANL). The goal of the Multi-intelligence (MINT) project is to determine the state of a facility from multiple data streams. The data streams are indirect observations. The researcher is using DARHT (Dual-Axis Radiographic Hydrodynamic Test Facility) as a proof of concept. In summary, videos from the DARHT facility contain a rich amount of information. Distribution of car activity can inform us about the state of the facility. Counting large vehicles shows promise as another feature for identifying the state of operations. Signal processing techniques are limited by the low resolution and compression of the videos. We are working on integrating these features with features obtained from other data streams to contribute to the MINT project. Future work can pursue other observations, such as when the gate is functioning or non-functioning.

97 MATHEMATICS AND COMPUTING↗

Research on miniature gas analysis systems

Technology for fabricating very small valves, whose function will be to introduce a small sample of the gas to be analyzed into the main carrier gas stream flowing through the chromatograph column is described. In addition, some analyses were made of the factors governing the resolution of gas chromatographs, particularly those with miniature columns. These analyses show how important the column lining thickness is in governing the ability of a miniature column to separate components of an unknown gas. A brief description of column lining factors is included. Preliminary work on a super small thermistor detector is included.

Angell, J. B.↗

California coastal processes study

Preliminary findings are presented and applications derived from ERTS-1 satellite imagery of the nearshore coastal processes of the California coast. The objectives were to analyze nearshore currents, sediment transport, and estuarine and river discharges along the California coast through the use of synoptic and repetitive imagery from ERTS as well as aircraft underflights and surface data. The major conclusions are: (1) Distinct seasonal patterns for sediment transport as a function of the oceanic current systems and coastal morphology have been identified. (2) Large scale sediment plumes from intermittent streams and rivers extend offshore to previously unanticipated ranges. (3) Computer generated contouring of radiance levels from computer-compatible tapes result in charts that can be used for determination of surface and nearsurface suspended sediment distribution. (4) Flying spot scanner enhancements result in details of nearshore features. (5) Data is providing significant information for coastal planning and construction projects.

Pirie, D. M.↗

Spatial stability of a compressible mixing layer

Presented are the results of a study of the inviscid spatial stability of a parallel compressible mixing layer. The parameters of this study are the Mach number of the moving stream, the ratio of the temperature of the stationary stream to that of the moving stream, the frequency and the direction of propagation of the disturbance wave. Stability characteristics of the flow as a function of these parameters are given. It is shown that if the Mach number exceeds a critical value there are always two groups of unstable waves. One of these groups is fast with phase speeds greater than 1/2, and the other is slow with speeds less than 1/2. Phase speeds for the neutral and unstable modes are given, as well as growth rates for the unstable modes. It is shown that three dimensional modes have the same general behavior as the two dimensional modes but with higher growth rates over some range of propagation direction. Finally, a group of very low frequency unstable modes was found for sufficiently large Mach numbers. These modes have very low phase speeds but large growth rates.

Jackson, T. L.↗

Inviscid spatial stability of a compressible mixing layer

Presented are the results of a study of the inviscid spatial stability of a parallel compressible mixing layer. The parameters of this study are the Mach number of the moving stream, the ratio of the temperature of the stationary stream to that of the moving stream, the frequency and the direction of propagation of the disturbance wave. Stability characteristics of the flow as a function of these parameters are given. It is shown that if the Mach number exceeds a critical value there are always two groups of unstable waves. One of these groups is fast with phase speeds greater than 1/2, and the other is slow with speeds less than 1/2. Phase speeds for the neutral and unstable modes are given, as well as growth rates for the unstable modes. It is shown that three-dimensional modes have the same general behavior as the two-dimensional modes but with higher growth rates over some range of propagation direction. Finally, a group of very low frequency unstable modes was found for sufficiently large Mach numbers. These modes have very low phase speeds but large growth rates.

Jackson, T. L.↗

Quick-Mixing Studies Under Reacting Conditions

The low-NO(x) emitting potential of rich-burn/quick-mix/lean-burn )RQL) combustion makes it an attractive option for engines of future stratospheric aircraft. Because NO(x) formation is exponentially dependent on temperature, the success of the RQL combustor depends on minimizing high temperature stoichiometric pocket formation in the quick-mixing section. An experiment was designed and built, and tests were performed to characterize reaction and mixing properties of jets issuing from round orifices into a hot, fuel-rich crossflow confined in a cylindrical duct. The reactor operates on propane and presents a uniform, non-swirling mixture to the mixing modules. Modules consisting of round orifice configurations of 8, 9, 10, 12, 14, and 18 holes were evaluated at a momentum-flux ratio of 57 and jet-to-mainstream mass-flaw ratio of 2.5. Temperatures and concentrations of O2, CO2, CO, HC, and NO(x) were obtained upstream, down-stream, and within the orifice plane to determine jet penetration as well as reaction processes. Jet penetration was a function of the number of orifices and affected the mixing in the reacting system. Of the six configurations tested, the 14-hole module produced jet penetration close to the module half-radius and yielded the best mixing and most complete combustion at a plane one duct diameter from the orifice leading edge. The results reveal that substantial reaction and heat release occur in the jet mixing zone when the entering effluent is hot and rich, and that the experiment as designed will serve to explore satisfactorily jet mixing behavior under realistic reacting conditions in future studies.

Leong, May Y.↗

The Deflection Plate Analyzer: A Technique for Space Plasma Measurements Under Highly Disturbed Conditions

A technique has been developed to measure the characteristics of space plasmas under highly disturbed conditions; e.g., non-Maxwellian plasmas with strong drifting populations and plasmas contaminated by spacecraft outgassing. The present method is an extension of the capabilities of the Differential Ion Flux Probe (DIFP) to include a mass measurement that does not include either high voltage or contamination sensitive devices such as channeltron electron multipliers or microchannel plates. This reduces the complexity and expense of instrument fabrication, testing, and integration of flight hardware as compared to classical mass analyzers. The new instrument design is called the Deflection Plate Analyzer (DPA) and can deconvolve multiple ion streams and analyze each stream for ion flux intensity (density), velocity (including direction of motion), mass, and temperature (or energy distribution). The basic functionality of the DPA is discussed. The performance characteristics of a flight instrument as built for an electrodynamic tether mission, the Propulsive Small Expendable Deployer System (ProSEDS), and the instrument s role in measuring key experimental conditions are also discussed.

Wright, Kenneth H., Jr.↗

Plastids and gravitropic sensing

Data and theories about the identity of the mass that acts in gravitropic sensing are reviewed. Gravity sensing may have evolved several times in plants and algae in processes such as gravitropism of organs and tip-growing cells, gravimorphism, gravitaxis, and the regulation of cytoplasmic streaming in internodal cells of Chara. In the latter and in gravitaxis, the mass of the entire cell may function in sensing. But gravitropic sensing appears to rely upon the mass of amyloplasts that sediment since (i) the location of cells with sedimentation is highly regulated, (ii) such cells contain other morphological specializations favoring sedimentation, (iii) sedimentation always correlates with gravitropic competence in wild-type plants, (iv) magnetophoretic movement of rootcap amyloplasts mimics gravitropism, and (v) starchless and intermediate starch mutants show reduced gravitropic sensitivity. The simplest interpretation of these data is that gravitropic sensing is plastid-based.

Review, Tutorial↗

The Deflection Plate Analyzer: A Technique for Space Plasma Measurements Under Highly Disturbed Conditions

A technique has been developed to measure the characteristics of space plasmas under highly disturbed conditions; e.g., non-Maxwellian plasmas with strong drifting populations and plasmas contaminated by spacecraft outgassing. The present method is an extension of the capabilities of the Differential Ion Flux Probe (DIFP) to include a mass measurement that does not include either high voltage or contamination sensitive devices such as channeltron electron multipliers or microchannel plates. This reduces the complexity and expense of instrument fabrication, testing, and integration of flight hardware as compared to classical mass analyzers. The new instrument design is called the Deflection Plate Analyzer (DPA) and can deconvolve multiple ion streams and analyze each stream for ion flux intensity (density), velocity (including direction of motion), mass, and temperature (or energy distribution). The basic functionality of the DPA is discussed. The performance characteristics of a flight instrument as built for an electrodynamic tether mission, the Propulsive Small Expendable Deployer System (ProSEDS), and the instrument s role in measuring key experimental conditions are also discussed.

Wright, Kenneth H., Jr.↗

Spatial Study 2022: Water Column, Sediment, and Total Ecosystem Respiration Rates across the Yakima River Basin, Washington, USA (v2)

This dataset supports a broader study examining the drivers of spatial variability in sediment respiration rates in the Yakima River Basin and is associated with the manuscript “Sediment-associated processes account for most of the spatial variation in ecosystem respiration in the Yakima River basin” submitted to Nature Communications Earth & Environment (Garayburu-Caruso et al., in review). The dataset provides ecosystem metabolism estimates generated from streamMetabolizer (Appling et al.; 2018) using data collected during the same five-week period at 48 sites within multiple rivers throughout the Yakima River Basin in Washington, USA. Additionally, it includes the scripts used for the analysis and producing the figures in the manuscript. The contents include streamMetabolizer inputs and outputs and additional relevant data needed to generate the main manuscript results. The data included are: total ecosystem respiration, water respiration, calculated sediment-associated respiration, gross primary production outputs from the river corridor model for the Yakima River Basin, median grain size (d50), depth, dissolved oxygen, water temperature, pressure, and annual oxygen consumption. The associated GitHub repository can be found at https://github.com/river-corridors-sfa/SSS_metabolism. Samples collected during this study were labeled as “Second Spatial Study” or “SSS.” Raw time series sensor data, total suspended solids, and depth data from SSS were published at https://data.ess-dive.lbl.gov/datasets/doi:10.15485/1969566. A subset of data from the SSS samples were published in the contiguous United States (CONUS)-Scale Model-Sample (CM) study data package available at https://data.ess-dive.lbl.gov/view/doi:10.15485/1923689 that presents data from across the CONUS. They include dissolved organic carbon (DOC, measured as non-purgeable organic carbon, NPOC), total nitrogen (TN), grain size, aerobic sediment respiration, dissolved oxygen (DO), and temperature. Parent IDs and Site IDs are consistent between the SSS and CM data packages, and they can be mapped directly so data across packages can be used together. Field metadata for the samples in this da This dataset is comprised of one main data folder with four subfolders. The main data folder contains of (1) file-level metadata; (2) data dictionary; (3) total/water column/sediment respiration; (4) gross primary production (GPP); (5) median grain size (d50); and (6) annual oxygen consumption. The “Figures” subfolder contains the figures used in the paper and all intermediate files (including geospatial files). The “Published_Data” contains a readme directing the user to download the public data to reproduce analyses and figures. The “Scripts” folder contains all scripts used in the analyses that were not part of running StreamMetabolizer. Lastly, the “Stream_Metabolizer” folder contains all files associated with running StreamMetabolizer including (1) model input files, (2) model output files, (3) processing scripts, (4) histogram plots of the outputs, and (5) an R project. All files are .csv, .pdf, .R, .Rmd, .Rproj, .html, .png, .txt, .qgz, .cpg, .dbf, .prj, .shp, .shp.ea.iso.xml, .shp.iso.xml, .shx, .sbn. ta package can be found at either link. We acknowledge the Yakama Nation as owners and caretakers of the lands where we collected these data. We thank the Confederated Tribes and Bands of the Yakama Nation Tribal Council and Yakama Nation Fisheries for working with us to facilitate sample collection and optimization of data usage according to their values and worldview.

54 ENVIRONMENTAL SCIENCES↗

Selective Removal of Lanthanides from Natural Waters, Acidic Streams and Dialysate

The increased demand for the lanthanides in commercial products result in increased production of lanthanide containing ores, increasing public exposure to the lanthanides, both from various commercial products and from production wastes/effluents. This work investigates lanthanide (La, Ce, Pr, Nd, Eu, Gd, Lu) binding properties of self-assembled monolayers on mesoporous silica supports (SAMMS®) that were functionalized with diphosphonic acid (DiPhos), acetamide phosphonic acid (AcPhos), propionamide phosphonic acid (ProPhos), and 1-hydroxy-2-pyridinone (1,2-HOPO) from natural waters (river, ground, and sea waters), acid solutions (to mimic certain industrial process streams), and dialysate and compares their performance to a high surface area activated carbon. The properties include sorption affinity, capacity, and sorption kinetics. Stability and regenerability of SAMMS materials were also investigated. Going from the acid side over to the alkaline side, the AcPhos- and DiPhos-SAMMS maintain their outstanding affinity for lanthanides, which enable the use of the materials in the systems where the pH may fluctuate. While the activated carbon is as effective as 1,2-HOPO-SAMMS for capturing lanthanides in natural (alkaline) waters, it has no affinity in acid solutions (pH 2.4) and low affinity in carbonate-rich dialysate. Over 99% of 100 ug/L of Gd in dialysate was removed by the ProPhos-SAMMS after ten minutes. SAMMS can be regenerated with an acid wash (0.5 M HCl) without losing the binding properties, for a number of regeneration cycles. In acid solutions, PhoPhos- and 1,2-HOPO-SAMMS have differing affinity along the lanthanide series, suggesting their potential for chromatographic lanthanide separations. Thus, SAMMS materials have a great potential to be used as sorbents in large scale treatment of lanthanides, lanthanide separation prior to analytical instruments, and sorbent dialyzers for lanthanide clearances.

acidic streams↗

Lignin valorization reshapes sustainable biomass refining

As the largest natural reservoir of aromatics, lignin offers significant potential for bioproduct manufacturing through advances in valorization technologies. However, the intrinsically complex structures of lignin pose significant challenges for its fractionization and downstream valorization. Overcoming challenges in lignin chemistry modification is crucial for achieving effective lignin valorization and establishing sustainable biorefinery industries. This review explores the potential of tailoring lignin reactivity to enable functional bioproduct manufacturing thereby contributing to profitable biorefining. The intrinsic characteristics of lignin are first summarized, highlighting their roles in both fractionization and valorization. The latest progress in lignin fractionation is then presented, emphasizing their potential to tailor lignin chemistry, reactivity, and processibility. Furthermore, advancements in lignin valorization are covered, recognizing that tailored lignin reactivity is key to defining bioproduct functionality. By examining these chemical mechanisms, this review sheds on the structure-function relationships between lignin and its derived products. To address the dilemma of lignin valorization and biorefineries, a promising synergistic biorefinery is proposed. This involves redesigning biomass fractionation strategies, tailoring lignin chemistry, and upgrading both carbohydrate and lignin streams across the entire biorefinery chain—from feedstock to application. Altogether, a deeper understanding of tailored lignin chemistry is crucial for decoding the reaction mechanisms in biomass processing. A synergistic biorefinery could harness lignin's intrinsic properties to improve product functionality and address key challenges, paving the way for cost-effective, sustainable biorefinery solutions.

09 BIOMASS FUELS↗