Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “STAINLESS STEELS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Effect of thermal oxidation on helium implanted 316L stainless steel

The effect of thermal oxide layer on He implanted 316L stainless steel was studied to evaluate experimentally how thermal oxidation affects the diffusion and distribution of He in the material. In the case of thermal oxidation of a He implanted sample, with an increase in oxidation time, the max swelling height increases logarithmically as a function of time and finally saturates for all samples except for the lowest dose of implanted He. Concerning TEM results, two void regions are identified. Similar to the calculation, the total irradiated depth was around 250 nm and the large void region was formed around 100–150 nm depth. On the other hand, the small void region was observed immediately under oxide layer from the thermal oxidation. In contrast, there were no voids in the altered zone near the metal/oxide interface in the non-thermal oxidized/He implanted sample. This description of the phenomena was justified using the Kirkendall effect and the Point Defect Model.

36 MATERIALS SCIENCE↗

A Thin Alumina Film as a Tritium Adsorption Inhibitor for Stainless Steel 316

The effect of a thin alumina coating on stainless-steel 316 (SS316) samples on tritium adsorption and transport are discussed. Compact films of alumina were produced on the surfaces of pristine SS316 samples using an atomic layer deposition (ALD) technique. Subsequently, these samples were exposed for 24 hours to a deuterium-tritium gas mixture (P T =0.5 atm, 25°C). A combination of methods including selective-etching and programmed thermal desorption were employed to assess both, the depth profile of the tritium concentration in the sample and the total quantity of tritium absorbed respectively. Tritium was quantitatively determined through the measurement of beta radioactivity using liquid-scintillation counting techniques. Data suggest that SS316 with a thin film of alumina reduces the total tritium uptake by ~25% relative to uncoated samples. Significantly, such films appear to reduce, by a factor of 200, tritium diffusion into SS316 and therefore constitute an effective barrier against tritium transport. This observation is of practical importance for tritium and, generally, reactive gas handling.

36 MATERIALS SCIENCE↗

Report on Updated Properties Handbook of Printed Stainless Steel 316

This report focuses on summarizing mechanical behavior of 316H stainless steel (SS) printed using laser powder bed fusion (LPBF). 316H SS is one of the six alloys that has been qualified for use in nuclear reactors. The Advanced Materials and Manufacturing Technologies (AMMT) program has identified the use of the additive manufacturing (AM) process of LPBF as one of the manufacturing modalities to fabricate components for nuclear applications. Unlike wrought material, AM material displays significant heterogeneity in properties, resulting from changes in process parameters, machine-to-machine variability, and minor changes in feedstock chemistry from one batch to another. Although significant work has been done on 316L SS in the literature and has been summarized in several review papers, very limited data exist on 316H SS. Therefore, this report aims to provide a concise summary of the properties of 316H SS printed using different machines and at different locations as a part of the AMMT program.

36 MATERIALS SCIENCE↗

Materials data handbook: Stainless steel type 301

A summary of the materials property information for stainless steel type 301 is presented. The scope of the information includes physical and mechanical properties at cryogenic, ambient, and elevated temperatures. Information on material procurement, metallurgy of the alloy, corrosion, environmental effects, fabrication, and bonding is developed.

Muraca, R. F.↗

Study of austenitic stainless steel welded with low alloy steel filler metal

The tensile and impact strength properties of 316L stainless steel plate welded with low alloy steel filler metal were determined. Tests were conducted at room temperature and -100 F on standard test specimens machined from as-welded panels of various chemical compositions. No significant differences were found as the result of variations in percentage chemical composition on the impact and tensile test results. The weldments containing lower chromium and nickel as the result of dilution of parent metal from the use of the low alloy steel filler metal corroded more severely in a marine environment. The use of a protective finish, i.e., a nitrile-based paint containing aluminum powder, prevented the corrosive attack.

Burns, F. A.↗

Character of laser-glazed, plasma-sprayed zirconia coatings on stainless steel substrata

Partially stabilized zirconia was applied as coatings to 316L stainless steel substrata using an 80-kw arc-plasma unit. Some of these coating-substrate systems were subsequently glazed using a 10 kw CO2 continuous-wavelength laser. SEM was used to characterize the microstructures of the coatings and coating-substrate interfaces. Results are reported and discussed.

Fischman, G. S.↗

Combustion of 316 stainless steel in high-pressure gaseous oxygen

Upward combustion of 316 stainless steel (SS) rods is discussed and a combustion model is presented. The effects of varying oxygen pressure and rod diameter on the rate limiting processes for combustion of 316 SS are evaluated. The rate-limiting steps for combustion up 316 SS rods are shown to be dependent on the incorporation and mass transport of oxygen in the molten mass, and heat transfer between the molten mass and rod. Both these rate-limiting steps are shown to be dependent on rod diameter. Small (d/r/ = 0.051 cm) 316 SS rods are shown to be dependent on convective heat transfer, and larger rods (d/r/ not less than 0.32 cm) are shown to be dependent on oxygen incorporation and mass transport in the molten mass.

Benz, Frank↗

Fracture-tough, high hardness stainless steel and method of making same

A cryogenically-formed and tempered stainless steel is provided having improved fracture toughness and corrosion resistance at a given hardness level, such as, for example, of at least about Rc 60 for bearing applications. The steel consists essentially of, in weight %, about 21 to about 24% Co, about 11 to about 13% Cr, about 7 to about 9% Ni, about 0.1 to about 0.5% Mo, about 0.2 to about 0.3% V, about 0.28 to about 0.32% C, and the balance iron. The steel includes a cryogenically-formed martensitic microstructure tempered to include about 5 to about 10 volume % post-deformation retained austenite dispersed therein and M.sub.2 C-type carbides, where M is Cr, Mo, V, and/or Fe, dispersed in the microstructure.

Olson, Gregory B.↗

Characterization of irradiated AISI 316L stainless steel disks removed from the Spallation Neutron Source

Irradiated AISI 316L stainless steel disks were removed from the Spallation Neutron Source (SNS) for post-irradiation examination (PIE) to assess mechanical property changes due to radiation damage and erosion of the target vessel. Topics reviewed include high-resolution photography of the disk specimens, cleaning to remove mercury (Hg) residue and surface oxides, profile mapping of cavitation pits using high frequency ultrasonic testing (UT), high-resolution surface replication, and machining of test specimens using wire electrical discharge machining (EDM), tensile testing, Rockwell Superficial hardness testing, Vickers microhardness testing, scanning electron microscopy (SEM), and energy dispersive spectroscopy (EDS). The effectiveness of the cleaning procedure was evident in the pre- and post-cleaning photography and permitted accurate placement of the test specimens on the disks. Due to the limited amount of material available and the unique geometry of the disks, machine fixturing and test specimen design were critical aspects of this work. Multiple designs were considered and refined during mock-up test runs on unirradiated disks. The techniques used to successfully machine and test the various specimens will be presented along with a summary of important findings from the laboratory examinations.

cavitation-induced erosion↗

Heat and corrosion resistant cast CF8C stainless steel with improved high temperature strength and ductility

A CF8C type stainless steel alloy and articles formed therefrom containing about 18.0 weight percent to about 22.0 weight percent chromium and 11.0 weight percent to about 14.0 weight percent nickel; from about 0.05 weight percent to about 0.15 weight percent carbon; from about 2.0 weight percent to about 10.0 weight percent manganese; and from about 0.3 weight percent to about 1.5 weight percent niobium. The present alloys further include less than 0.15 weight percent sulfur which provides high temperature strength both in the matrix and at the grain boundaries without reducing ductility due to cracking along boundaries with continuous or nearly-continuous carbides. The disclosed alloys also have increased nitrogen solubility thereby enhancing strength at all temperatures because nitride precipitates or nitrogen porosity during casting are not observed. The solubility of nitrogen is dramatically enhanced by the presence of manganese, which also retains or improves the solubility of carbon thereby providing additional solid solution strengthening due to the presence of manganese and nitrogen, and combined carbon.

36 MATERIALS SCIENCE↗

Development of a passivated stainless steel surface

A multi-step Q-passivation method for stainless steel is described. The method includes a first high voltage electropolishing step followed by as separate low voltage chromium enhancement step. The method can also include a vacuum heat treatment step that utilizes a cyclic ramp-up period so as to maintain a relatively low pressure and low temperature throughout the step. The method can also include a controlled oxidation step during which the surface is contacted with an oxygen/inert gas mixture at low oxygen partial pressure.

36 MATERIALS SCIENCE↗

In-situ high-energy X-ray characterization of neutron irradiated HT-UPS stainless steel under tensile deformation

Here, the tensile deformation behavior of a high-temperature, ultrafine-precipitate strengthened (HT-UPS) stainless steel was characterized in-situ with high-energy X-ray diffraction at 20 and 400 °C. The HT-UPS samples were neutron irradiated to 3 dpa at 400 °C. Significant irradiation hardening and ductility loss were observed at both temperatures. Lattice strain evolutions of the irradiated samples showed a strong linear response up to near the onset of the macroscopic yield, in contrast to the unirradiated HT-UPS which showed a pronounced non-linear behavior well below the macroscopic yield. While the room temperature diffraction elastic moduli in the longitudinal direction increased after irradiation, the 400 degrees C moduli were similar before and after irradiation. The evolution of the {200} lattice strain parallel to the loading axis (ε L {200} ) showed unique characteristics: in the plastic regime, the evolution of (ε L {200} ) after yield is temperature-dependent in the unirradiated specimens but temperature-independent in the irradiated specimens; and the value of (ε L {200} ) at the yield is an irradiation-sensitive, temperature-independent . parameter. The evolution of (ε L {200} ) corresponds well with the dislocation density evolution, and is an effective probe of the deformation-induced long-range internal stresses in the HT-UPS steel.

36 MATERIALS SCIENCE↗

Oxidation behaviour of ferritic stainless steel grade Crofer 22 APU at 700 °C in flowing Ar−75%CO{sub 2}−12%H{sub 2}O

The oxidation of Ferritic Stainless Steel (FSS) grade Crofer 22 APU has been investigated. FSS alloys were exposed to isothermal conditions in a horizontal tube furnace at a 700 °C in flowing Ar−75%CO{sub 2}−12%H{sub 2}O at a pressure of approximately 1 atm. The results showed that the growth of non protective Fe{sub 2}O{sub 3} and spinel was observed after 50 h exposure in the presence of 12% H{sub 2}O. The weight was increased significantly with time of exposure. The formation of different oxides is presented on the interface of the specimen such as MnCr{sub 2}O{sub 4}, Fe{sub 3}O{sub 4} and Fe{sub 2}O{sub 3} were revealed by X-ray diffraction and supported by EDAX analysis. FSS did not form a protective Cr{sub 2}O{sub 3} layer due to water vapour accelerates the kinetics oxidation. Data of microstructure observation is presented and discussed in this paper in term of water vapour effects.

36 MATERIALS SCIENCE↗

Preparation and Characterization of Ultrathin Stainless Steel Films

We report on the preparation of polycrystalline austenitic 310 ({sup 57}Fe{sub 0.55}Cr{sub 0.25}Ni{sub 0.20}) stainless steel (SS) thin films on Si substrates and the characterization of their residual magnetism via {sup 57}Fe conversion-electron Moessbauer spectroscopy (CEMS). The films were structurally characterized at room temperature by X-ray diffraction (XRD). The virgin films were found to be structurally disordered. Subsequent annealing at moderate temperatures in ultrahigh vacuum produces the ordered martensitic and austenitic SS phases. Further annealing at higher temperatures (up to temperatures where long-range diffusion into the substrate is still weak) transforms the films into the austenitic phase with no trace of a magnetic hyperfine interaction. However, when a 2 nm thick SS thin film is embedded between two carbon layers, the as prepared disordered SS film does not transform to the martensitic or austenitic SS phase irrespective of the annealing temperature, probably because the interdiffusion with C prohibits the formation of these phases.

36 MATERIALS SCIENCE↗