Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SINTERED MATERIALS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Densification of non-radioactive porous siliceous particles loaded with cesium potassium copper hexacyanoferrate by spark plasma sintering

In the development of a conditioning process for cesium-bearing sorbents from the decontamination of aqueous waste streams, the treatment of a granular material composed of (Cs,K) 2 CuFe(CN) 6 loaded onto mesoporous silica particles has been investigated in an additive-free two-step conditioning process involving (i) calcination at 1000 °C to remove volatile species and (ii) densification by spark plasma sintering. A 92.0 % dense pellet was obtained after 10 min sintering at 850 °C under 100 MPa. Density and microstructural measurements indicate that densification is first driven by the viscous flow of a vitreous phase containing Cs, formed during calcination. Additionally, the density of the sample then increases further during sintering by grain boundary diffusion. However, a limited but non negligible part of cesium is lost during densification.

36 MATERIALS SCIENCE↗

A New Approach to Joining Dissimilar Ceramic Oxides for Chemical Sensors

Conventional joining of dissimilar oxides for sensing electrodes (SE) of chemical sensors has been pivotal to the development of various sensors and is vital to their further development. However, it is shown that the uncertainty (of a fundamental nature) in the properties of dissimilar oxides in SE causes the determination of their sensing characteristics to be ambiguous. Characteristics are different for such controlled parameters as pyrolysis temperature, crystal structure, particle's morphology and size, chemical and phase composition, the coefficient of thermal expansion (CTE), surface architecture, the bulk and surface stoichiometry and type and conductivity of additives. Here, we provide an alternative approach for joining dissimilar metal-oxides for chemical sensors SE. The approach relies on the development of at least one transient liquid oxide phase on the ceramic-SE interface. These results constitute key points relevant to selection oxides for joining, sintering temperatures and heating/cooling temperature rates.

36 MATERIALS SCIENCE↗

Superconductor-in-an-Hour: Spark Plasma Synthesis of Co- and Ni-Doped BaFe 2 As 2

In this work, BaFe 2 As 2 superconductors doped with Co or Ni were synthesized by heat treatment of the reactive BaH 2 precursor and elemental Fe, Co, Ni, and As in a sealed niobium container. The hydride route provides better mixing of the starting materials, resulting in faster preparation of the target phases. The hydrogen gas evolved during sintering facilitates the preparation of the oxygen-free powders. Using powder X-ray diffraction (PXRD), including low-temperature synchrotron PXRD, it was shown that this route leads to successful doping of the Co (Ni) dopant and that the actual dopant content in the produced powdered samples of BaFe 2– x Co x As 2 (0 ≤ x ≤ 0.4) and BaFe 2– x Ni x As 2 (0 ≤ x ≤ 0.18) is close to the nominal content. The optimally doped samples of BaFe 2– x Co x As 2 and BaFe 2– x Ni x As 2 exhibit bulk superconducting properties. The highest T c for the Co-doped sample is 24 K when x = 0.15–0.175 and 21 K for the Ni-doped sample when x ~ 0.1. The reaction mechanism between the BaH 2 hydride precursor and elemental Fe and As was studied by operando high-temperature synchrotron PXRD. The formation of the target BaFe 2 As 2 phase occurs at the relatively low temperature of 785 K with binary iron arsenide (FeAs) being an intermediate product. Finally, the in situ combined synthesis and sintering of the intimately mixed BaH 2 and Fe, Co, and As was performed inside the spark plasma sintering apparatus to obtain compact pellets of the BaFe 2– x Co x As 2 superconductors. A higher sintering temperature (>873 K) is needed to ensure a homogeneous Co dopant distribution and, thus, the abrupt superconducting transitions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Final-stage densification kinetics of direct current–sinteredZrB2

Final-stage sintering was analyzed for nominally phase pure zirconium diboride synthesized by borothermal reduction of high-purity ZrO2. Analysis was conducted on ZrB2 ceramics with relative densities greater than 90% using the Nabarro–Herring stress–directed vacancy diffusion model. Temperatures of 1900°C or above and an applied uniaxial pressure of 50 MPa were required to fully densify ZrB2 ceramics by direct current sintering. Ram travel data were collected and used to determine the relative density of the specimens during sintering. Specimens sintered between 1900 and 2100°C achieved relative densities greater than 97%, whereas specimens sintered below 1900°C failed to reach the final stage of sintering. The average grain size ranged from 1.0 to 14.7 μm. The activation energy was calculated from the slope of an Arrhenius plot that used the Kalish equation. The activation energy was 162 ± 34 kJ/mol, which is consistent with the activation energy for dislocation movement in ZrB2. The diffusion coefficients for dislocation motion that controls densification were 5.1 × 10−6 cm2/s at 1900°C and 5.1 × 10−5 cm2/s at 2100°C, as calculated from activation energy and average grain sizes. This study provides evidence that the dominant mechanism for final-stage sintering of ZrB2 ceramics is dislocation motion.

36 MATERIALS SCIENCE↗

High thermoelectric performance BiSbTe alloy with unique low-dimensional structure

We report a detailed description of an innovative route of a melt spinning (MS) technique combined with a subsequent spark plasma sintering process in order to obtain high performance p-type Bi{sub 0.52}Sb{sub 1.48}Te{sub 3} bulk material, which possesses a unique low-dimensional structure. The unique structure consists of an amorphous structure, 5-15 nm fine nanocrystalline regions, and coherent interfaces between the resulting nanocrystalline regions. Measurements of the thermopower, electrical conductivity, and thermal conductivity have been performed over a range of temperature of 300-400 K. We found that MS technique can give us considerable control over the resulting nanostructure with good thermal stability during the temperature range of 300-400 K and this unique structure can effectively adjust the transport of phonons and electrons, in a manner such that it is beneficial to the overall thermoelectric performance of the material, primarily a reduction in the lattice thermal conductivity. Subsequently, this results in a maximum figure of merit ZT value of 1.56 at 300 K for p-type Bi{sub 0.52}Sb{sub 1.48}Te{sub 3} bulk material. This ZT value is over a 50% improvement of that of the state of the art commercial Bi{sub 2}Te{sub 3} materials. We also report results of thermal cycling of this material for over one hundred cycles between 300-400 K. Our work offers an innovative route for developing high performance bismuth telluride based alloys and devices, which have even broader prospects for commercial applications. This technique may also be applicable to other thermoelectric materials.

36 MATERIALS SCIENCE↗

Two-watt radioisotope power generators for underwater applications

Materials and design considerations are discussed for a low-cost, reliable radio-isotope-fueled thermoelectric generator for use in an undersea application. Plutonium has been selected as fuel, and the generator has to meet design goals of 2 watts after 20 years with a direct output voltage of 6-8 volts. The pressed and sintered form of Bi2Te3 appears to be the most appropriate thermoelectric material. Both fibrous and multilayer foil insulation could be used with proper processing and quality control, but there is less risk with fibrous type insulation. Min-K 1400 is recommended with a nitrogen cover gas. The heat source recommended is a three-layer capsule using T-111 for both the liner and strength member with an outer liner of Hastelloy-C.

Caputo, R. S.↗

Physical and hydraulic properties of modern sinter deposits: El Tatio, Atacama

We report sinters are siliceous, sedimentary deposits that form in geothermal areas. Formation occurs in two steps. Hot water circulates in the subsurface and dissolves silica from the host rock, usually rhyolites. Silica then precipitates after hot water is discharged and cools. Extensive sinter formations are linked to up-flow areas of fluids originating from high temperature (> 175 °C) deep reservoirs. Fluid geochemistry, microbial communities, and environmental conditions of deposition determine the texture of sinter and pore framework. Porosity strongly influences physical and hydraulic properties of rocks. To better understand the properties controlling the transport of fluids, and interpret geophysical observations in geothermal systems, here we studied 17 samples of modern geyserite sinter deposits (< 10 ka) from the active El Tatio geothermal field in northern Chile. We measured the physical properties (hydraulic, seismic, and electrical), and internal microstructure (using μX-Ray computed tomography). We find that the pore structure, and thus hydraulic and physical properties, is controlled by the distribution of microbial matter. Based on velocity-porosity relationships, permeability-porosity scaling, and image analysis of the 3D pore structure; we find that the physical and hydraulic properties of sinter more closely resemble those of vesicular volcanic rocks and other material formed by precipitation in geothermal settings (i.e., travertine) than clastic sedimentary rocks.

15 GEOTHERMAL ENERGY↗

Bottom-up processing and low temperature transport properties of polycrystalline SnSe

A hydrothermal approach was employed to efficiently synthesize SnSe nanorods. The nanorods were consolidated into polycrystalline SnSe by spark plasma sintering for low temperature electrical and thermal properties characterization. The low temperature transport properties indicate semiconducting behavior with a typical dielectric temperature dependence of the thermal conductivity. The transport properties are discussed in light of the recent interest in this material for thermoelectric applications. The nanorod growth mechanism is also discussed in detail. - Graphical abstract: SnSe nanorods were synthesized by a simple hydrothermal method through a bottom-up approach. Micron sized flower-like crystals changed to nanorods with increasing hydrothermal temperature. Low temperature transport properties of polycrystalline SnSe, after SPS densification, were reported for the first time. This bottom-up synthetic approach can be used to produce phase-pure dense polycrystalline materials for thermoelectrics applications. - Highlights: • SnSe nanorods were synthesized by a simple and efficient hydrothermal approach. • The role of temperature, time and NaOH content was investigated. • SPS densification allowed for low temperature transport properties measurements. • Transport measurements indicate semiconducting behavior.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Microstructure and property characterization of sintered Si3N4, SiC, and SiAlON

Commercially-produced, pressureless sintered Si3N4, SiC, and SiAlON were characterized with respect to density, phases present, bend strength, and oxidation resistance. The room-temperature bend strengths of sintered Si3N4, SiC, and SiAlON are comparable. However, the room-temperature strengths are much lower (approximately 40 to 50%) than the room-temperature strength of hot-pressed Si3N4 (NC-132). The strength loss in Si3N4 and SiAlON materials at high temperature was attributed to a viscous grain-boundary phase, retained during cooling from the sintering temperature. The oxidation resistance of sintered alpha-SiC was the best of any materials tested.

Dutta, S.↗

In situ probing of interfacial roughness and transient phases during ceramic cold sintering process

The ceramic cold sintering process (CSP) offers an eco-friendly approach to producing fully dense ceramics at low temperatures. However, an incomplete mechanistic understanding hinders its optimization and widespread adoption. In this study, we analyze the microstructural and structural changes in ZnO, a model CSP system, using in situ synchrotron-based high-energy small-angle X-ray scattering and X-ray diffraction techniques. Our results reveal the time evolution of ZnO particles' surface area and roughness, reflecting the dissolution and re precipitation processes that enable densification. The in situ measurements supply valuable kinetic data for these stages of CSP. Alongside microstructural changes and densification, we observed the evolution of secondary phases representing reaction products between ZnO and acetic acid, the solvent used. The initial ZnO/solvent mixture's dominant secondary phase is attributed to zinc acetate, which is gradually replaced by a zinc soap-type structure during CSP. This structure has a large (≈ 21 Å) lattice parameter and is assumed to have a layered nature. The formation of this soap phase, which is retained in the sintered product as an intergranular component, appears to be a signature of successful cold sintering as it facilitates mass transport, leading to densification. Here, our study underscores the potential of in situ synchrotron characterization for revealing microstructural and phase-evolution details during CSP. These findings, which would be challenging to obtain through ex situ measurements, provide crucial data to guide and validate theoretical models, ultimately enhancing CSP's effectiveness and adoption.

36 MATERIALS SCIENCE↗

Developing Robust Ceria-Supported Catalysts for Catalytic NO Reduction and CO/Hydrocarbon Oxidation

Synthesis of robust and hydrothermally stable PGM/ceria materials for NO, CO, and hydrocarbon abatement remains a formidable challenge, as ceria and PGMs are known to sinter severely >800 °C under hydrothermal conditions, leading to irreversible activity loss. In this work, we tackle this challenge by synthesizing well-defined catalysts with atomically dispersed rhodium supported on ceria with varying abundance of (100), (101), and (111) facets. Evaluation of these catalysts for NO reduction by CO as well as CO and propylene oxidation under model and industrially relevant conditions reveals pronounced reactivity and stability differences. Different modes of interaction of Rh ions with the ceria facets and their facile reducibility were shown to be the crucial parameters controlling reactivity, resulting in pronounced activity and stability variations. Facet-dependent poisoning of surfaces by nitrites was identified as the main reason for deactivation of the catalysts at low temperature, which is mitigated for (111) ceria facets. (111)-enriched ceria nanoparticles survive very harsh hydrothermal aging at 950 °C by maintaining and preserving (111) facets, unlike other ceria nanoparticles which sinter into poorly defined shapes. Thus, putting atomically dispersed PGM sites on (111) ceria facets lead to the catalytic material with the highest activity and stability for all studied reactions, providing the pathway to catalysts that can endure extremely harsh hydrothermal aging conditions.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Laboratory studies on cometary crust formation: The importance of sintering

It is demonstrated by experiments and theoretical considerations that sintering processes, so far used to describe the densification of metal and ceramic powders, are relevant for icy materials and therefore probably also for comets. A theoretical model is presented which describes the evolution of so called sinter necks, the contact zone between ice particles. With this model the strength increase of a porous, loosley packed icy body is calculated in which the sinter necks grow by evaporation and condensation of water vapor at a constant temperature. Experiments with ice powders validate the model qualitatively. An increase in strength up to a factor of four is observed during isothermal sintering. In order to check the relevance of the experimental results and the basic theoretical ideas with respect to real comets, more exact theories and improved experiments taking into account additional mass transport mechanisms are needed.

Ratke, L.↗

Effects of the addition of boron nitride nanoplate on the fracture toughness, flexural strength, and Weibull Distribution of hydroxyapatite composites prepared by spark plasma sintering

Hydroxyapatite (HA) has inherently low fracture toughness and low flexural strength, thus limiting it from wide scale application as an implant material in the biomedical field. To increase the fracture toughness and flexural strength, HA composites were fabricated by adding boron nitride nanoplatelets (BNNP) as reinforcement. Spark plasma sintering was utilized to achieve fine grain structure. The addition of BNNP facilitated grain size refinement. The BNNP reinforced HA composites exhibited increased fracture toughness (2.3 MPa m 1/2 ) and flexural strength (79.79 MPa) of HA over previous published values (1.0 MPa m 1/2 ). Despite that the Weibull Distribution indicated a sacrifice in mechanical reliability, all the composites fabricated in this study showed a low probability of failure and a factor of safety (~ 5.6) that is consistent with that of human bones (~ 6). In addition, the current study provides an approach to statistically design sintering parameters and mechanical loading for fabrication of ceramics.

36 MATERIALS SCIENCE↗

Effect of Gold on the Microstructural Evolution and Integrity of a Sintered Silver Joint

There is a need for next-generation, high-performance power electronic packages and systems employing wide band gap devices to operate at high temperatures in automotive and electric grid applications. Sintered silver joints are currently being evaluated as an alternative to Pb-free solder joints. Of particular interest is the development of joints based on silver paste consisting of nanoscale or micron scale particles that can be processed without the application of an external pressure. Microstructural evolution at the interface of a pressureless sintered silver joint formed between a SiC die with a Ti/Ni/Au metallization and an Active Metal Brazed substrate with Ag metallization at 250 °C was evaluated using Scanning Electron Microscopy, X-ray microanalysis, and X-ray Photo Electron Spectroscopy. Results from Focused Ion Beam cross-sections show that during sintering, the pores in the sintered region close to the Au layer tend to be smaller and are oriented predominantly with their longer dimension oriented parallel to the interface. With further densification, this results in the alignment of small pores parallel to the interface, creating a path for easy crack propagation. Lastly, X-ray microchemical analyses results confirm interdiffusion between Au and Ag and that a region with poor mechanical strength is formed at the edge of this region of interdiffusion.

36 MATERIALS SCIENCE↗

Coercivity enhancement of sintered Nd-Fe-B magnets by chemical bath deposition of TbCl{sub 3}

The chemical bath deposition (CBD) and the grain boundary diffusion method were combined to diffuse the heavy rare earth for obtain the thick magnets with high coercivity and low heavy rare earth. The jet mill powders were soaked into the alcohol solution of 0.2 wt. % TbCl{sub 3}. A thin layer of TbCl{sub 3} was wrapped to the surface of (PrNd){sub 2}Fe{sub 14}B powder particles. The coercivity of magnet is increased from 11.89 kOe to 14.72 kOe without significant reduction of remanence after grain boundary diffusion in the sintering and the annealing processes. The temperature coefficients of the remanence and the coercivity are improved by the substitution of PrNd by Tb in the surface of grains. The highly accelerated temperature/humidity stress test (HAST) results indicate that the CBD magnet has poor corrosion resistance, attributing to the present of Cl atoms in the grain boundaries.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

High Performance PrFeB Permanent Magnets through Novel Pulse Alignment and Compaction Method for Cryogenic Permanent Magnet Undulators (CPMU)

The Phase I feasibility results of processing PrFeB magnets have shown highly promising magnetic property results with the potential to equal or exceed the best PrFeB properties reported. These findings will be advanced in Phase II through composition tuning, optimization of powder alignment from 95% to > 98%, sintering and heat treat adjustments. The objectives of Phase I were successfully achieved during Phase I work. These were to produce PrFeB magnets and test to establish a baseline process including material chemistry, alloy milling to 3 microns, compaction with domain alignment, and liquid Phase sintering and annealing – under both thermal and vacuum cycles. Success of proper chemistry and processing is determined by the finished magnet density and magnetic performance. A density of 7.45 +/-0.03 g/cm3 has been established as demonstrating full density.

36 MATERIALS SCIENCE↗

Low-Thermal-Conductivity Pyrochlore Oxide Materials Developed for Advanced Thermal Barrier Coatings

When turbine engines operate at higher temperatures, they consume less fuel, have higher efficiencies, and have lower emissions. The upper-use temperatures of the base materials (superalloys, silicon-based ceramics, etc.) used for the hot-section components of turbine engines are limited by the physical, mechanical, and corrosion characteristics of these materials. Thermal barrier coatings (TBCs) are applied as thin layers on the surfaces of these materials to further increase the operating temperatures. The current state-of-the-art TBC material in commercial use is partially yttria-stabilized zirconia (YSZ), which is applied on engine components by plasma spraying or by electron-beam physical vapor deposition. At temperatures higher than 1000 C, YSZ layers are prone to sintering, which increases thermal conductivity and makes them less effective. The sintered and densified coatings can also reduce thermal stress and strain tolerance, which can reduce the coating s durability significantly. Alternate TBC materials with lower thermal conductivity and better sintering resistance are needed to further increase the operating temperature of turbine engines.

Bansal, Narottam P.↗