Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “SIGNAL CONDITIONING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Combustion Dynamics Characteristics and Fuel Pressure Modulation Responses of a Three-Cup Third-Generation Swirl-Venturi Lean Direct Injection Combustion Concept

This paper presents the combustion dynamic data and fuel modulation response of a three-cup Lean Direct Injection combustor developed by Woodward, FST. The test was conducted at the NASA Glenn Research Center CE-5 flame tube test facility. The facility provided inlet air up to 922 K and pressure up to 19.0 bar. At the low-power configuration, the combustion noise was quiet. Large combustion pressure oscillations were observed with the High-power configuration at an off design condition, with low inlet air temperature and pressure conditions and a high equivalence ratio (about T3=600 K, P3 = 800 kPa, and ER =0.46). The noise amplitude was as high as 1.5 psi at around 220 Hz. As inlet air pressure and temperature increased, this combustion instability decreased. Fuel modulated signals were produced with the WASK fuel modulator located in the fuel line upstream of the center cup pilot fuel-air mixer. The amplitudes of the modulated signals detected in the combustor were low. Only less than 0.13% (0.06 psi) of the input energy was detected, and the signal amplitudes decreased as the modulated frequencies increased. Interaction between the modulated signals and the combustion noise varied with operating conditions. At a condition with low combustion noise around 150 hz, modulating a signal at around the same frequency would increase the combustion noise from 0.2 psi to as high as 0.6 psi, whereas at a condition with a high combustion instability around 250 hz, the modulated signal did not seem to have much effect on the combustion noise.

Fuel flexible combustor↗

Use of Modal Sensitivity to Operating Conditions for Damping Control in Power Systems

Small signal stability is an inherent characteristic of dynamic systems such as power systems. Pole positioning through power system stabilizers (PSS) is often used for improving damping in power systems. A well-designed PSS can be very effective in damping oscillations, especially local oscillations. However, designing PSSs for inter-area oscillations has been a very challenging task due to time-varying operating conditions affecting the characteristics of inter-area oscillations. This paper explores the sensitivity relationship between oscillations and operating conditions and employs the relationship to derive recommendations for operator’s actions to adjust operating conditions so as to improve damping. Low damping is usually considered to be a result of heavy power transfer in long distance. Studies in this paper show that this generally holds true while locations have significant impact on damping of oscillations. Therefore it is important to consider locations in deriving recommendations. This paper proposes the concept of relative modal sensitivity and presents the application of relative modal sensitivity to derive recommendations for operator’s action in damping control.

Huang, Zhenyu↗

Controlling the Properties of Spin–Wave Transport in a Semiring Magnon Microwavevguide

Spin-wave transport along a waveguide structure with disturbed translational symmetry has been investigated. A semiring portion of a magnon microwaveguide has been made of a YIG film. It has been shown that one can control the dynamic magnetization spatial distribution by varying the magnetic biasing angle in the microwaveguide plane. Under such conditions, the transmission coefficient of standing waves changes noticeably. The structure suggested in this paper allows the rotation of spin-wave signals in an irregular configuration under the conditions of surface magnetostatic wave propagation. This effect may be used in planar magnon networks.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Direct measurement of the propagation velocity of defects using coherent X-rays

The properties of artificially grown thin films are often strongly affected by the dynamic relationships between surface growth processes and subsurface structure. Coherent mixing of X-ray signals promises to provide an approach to better understand such processes. Here, we demonstrate the continuously variable mixing of surface and bulk scattering signals during realtime studies of sputter deposition of a-Si and a-WSi2 films by controlling the X-ray penetration and escape depths in coherent grazing-incidence small-angle X-ray scattering. Under conditions where the X-ray signal comes from both the growth surface and the thin film bulk, oscillations in temporal correlations arise from coherent interference between scattering from stationary bulk features and from the advancing surface. We also observe evidence that elongated bulk features propagate upwards at the same velocity as the surface. Moreover, a highly surface-sensitive mode is demonstrated that can access the surface dynamics independently of the subsurface structure.

36 MATERIALS SCIENCE↗

Testing the Responses of Three PSF Fitting Methods

We present an analysis of prototype code designed to fit point-spread functions to point-like astronomical objects appearing in images taken by DECam, or the Dark Energy Camera. We test three methods, each of which yields a maximum likelihood estimate for a different likelihood function. We call these methods Poisson likelihood, χ 2 with background error, and χ 2 with data error, and describe their differences mathematically. Each is used to construct a fit involving up to four parameters characterizing the raw pixel data. We measure biases in the signal and background levels under a variety of conditions. We test the variance and error estimate of the fits as a function of signal strength, outline areas of sensitivity, and demonstrate the effects of incomplete or inaccurate information on the Poisson fit. We conclude that the Poisson likelihood fitting method is best, as it is successful in all circumstances under which the χ 2 series are, and displays other favorable attributes where the others do not.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Role of the Atmospheric Mean State on the Initiation of the Madden-Julian Oscillation in a Tropical Channel Model

Tropical channel models, defined as models that are global in the zonal direction but bounded in the meridional direction, are particularly useful for simulating the Madden-Julian oscillation (MJO) and understanding its physical and dynamical basis. Influences from the extratropics through the lateral boundaries have been found to be essential to the reproduction of the initiation of certain MJO events. This led to a hypothesis that multi-year simulations using a tropical channel model would reproduce reasonable MJO statistics under the influence of prescribed lateral boundary conditions derived from global reanalyses. Interestingly, the MJO statistics in such a multi-year simulation by a high-resolution tropical channel model are not better than those from global climate models. The error in the atmospheric mean state is found to be a possible reason for the poor MJO statistics in the simulation. Nevertheless, even with a large error in the mean state, the multi-year simulation captures two MJO events previously found to be initiated by extratropical influences. However, the model does not reproduce a third event, whose initiation is not directly influenced by the extratropics. This implies that in the absence of dynamical interactions between the MJO and the lateral boundary conditions, the error in the mean state could be sufficient to prevent the MJO initiation. To explore this third MJO event further, a series of sensitivity tests are conducted. These tests show that the simulation of this event is neither critically influenced by the cumulus parameterization employed, nor the initial conditions when the model is integrated 2 weeks prior to the MJO initiation. The model captures this event when the MJO signal is already present in the initial conditions. The use of highresolution sea surface temperature does not improve the simulation of the third MJO event. A higher-resolution nested domain covering the Indo-Pacific warm pool region and including a cloud-system resolving domain over the Indonesian Maritime Continent has little effect on the MJO initiation over the Indian Ocean. In\2 weeks the error in the simulation is comparable to the climate error. The role of the simulated MJO on the mean state is also explored. Implications and limitations of these results are discussed.

54 ENVIRONMENTAL SCIENCES↗

Using Ensemble Data Assimilation to Estimate Transient Hydrologic Exchange Flow Under Highly Dynamic Flow Conditions

Abstract Quantifying dynamic hydrologic exchange flows (HEFs) within river corridors that experience high‐frequency flow variations caused by dam regulations is important for understanding the biogeochemical processes at the river water and groundwater interfaces. Heat has been widely used as a tracer to infer steady‐state flow velocities through analytical solutions of heat transport defined by the diurnal temperature signals. Under sub‐daily dynamic flow conditions, however, such analytical solutions are not applicable due to the violation of their fundamental assumptions. In this study, we developed a data assimilation‐based approach to estimate the sub‐daily flux under highly dynamic flow conditions using multi‐depth temperature observations at a 5‐min resolution. If the hydraulic gradient is measured, Darcy's law was used to calculate the flux with permeability estimated from temperature responses below the riverbed. Otherwise, flux was estimated directly by assimilating multi‐depth temperature data at 1‐ or 2‐hr time intervals assuming one‐dimensional flow and heat transport governing equation. By comparing estimated fluxes with model‐generated synthetic truth, we demonstrated that both schemes have robust performance in estimating fluxes under highly dynamic flow conditions. This data assimilation‐based flux estimation method was able to capture the vertical sub‐daily fluxes using multi‐depth high‐resolution temperature data alone, even in the presence of multi‐dimensional flow. This approach has been successfully applied to real field temperature data collected at the Hanford site, which experiences highly dynamic HEFs. Our study shows the promise of adopting distributed 1‐D temperature monitoring to capture spatial and temporal exchange dynamics in river corridors at a watershed scale or beyond.

54 ENVIRONMENTAL SCIENCES↗

2010 GORDON RESEARCH CONFERENCE ON MITOCHONDRIA & CHLOROPLASTS, LUCCA, ITALY, JULY 11-16, 2010

The 2010 GRC on Mitochondria & Chloroplasts will assemble an international group of molecular, structural and cellular biologists, biochemists and geneticists investigating a broad spectrum of fundamental problems related to the biology of these organelles in animal, plant and fungal cells. This field has witnessed an extraordinary expansion in recent years, fueled by the discovery of the role of mitochondria in human disease and ageing, and of the synergy of chloroplasts and mitochondria in energetic output, the identification of novel factors involved in organelle division, movement, signaling and acclimation to changing environmental conditions, and by the powerful tools of organelle proteomics. The 2010 GRC will highlight advances in the elucidation of molecular mechanisms of organelle biogenesis including regulation of genome structure, evolution and expression, organellar protein import, assembly and turnover of respiratory and photosynthetic complexes, bidirectional signaling between organelles and nucleus, organelle morphology and dynamics, and the integration of cellular metabolism. We will also explore progress in mechanisms of disease and ageing/ senescence in animals and plants. The organellar field has forged new fronts toward a global and comprehensive understanding of mitochondrial and chloroplast biology at the molecular level. Many of the molecules under study in model organisms are responsible for human diseases, providing significant impetus for a meeting that encourages interactions between mammalian, fungal and plant organellar biologists.

59 BASIC BIOLOGICAL SCIENCES↗

Effects of repetitive pulsing on multi-kHz planar laser-induced incandescence imaging in laminar and turbulent flames

Planar laser-induced incandescence (LII) imaging is reported at repetition rates up to 100 kHz using a burst-mode laser system to enable studies of soot formation dynamics in highly turbulent flames. Furthermore, to quantify the accuracy and uncertainty of relative soot volume fraction measurements, the temporal evolution of the LII field in laminar and turbulent flames is examined at various laser operating conditions. Under high-speed repetitive probing, it is found that LII signals are sensitive to changes in soot physical characteristics when operating at high laser fluences within the soot vaporization regime. For these laser conditions, strong planar LII signals are observed at measurement rates up to 100 kHz but are primarily useful for qualitative tracking of soot structure dynamics. However, LII signals collected at lower fluences allow sequential planar measurements of the relative soot volume fraction with a sufficient signal-to-noise ratio at repetition rates of 10–50 kHz. Finally, guidelines for identifying and avoiding the onset of repetitive probe effects in the LII signals are discussed, along with other potential sources of measurement error and uncertainty.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Runaway electron beam dynamics at low plasma density in DIII-D: energy distribution, current profile, and internal instability

Parameters of the post-disruption runaway electron (RE) beam in the collisionless background plasma achieved after deuterium injection are investigated in DIII-D. The spatially resolved RE energy distribution function is measured for the first time during the RE plateau stage by inverting hard X-ray bremsstrahlung spectra. It has maximum energy up to 20 MeV and a non-monotonous feature at 5{6 MeV observed only in the core of the beam supporting the possibility of kinetic instabilities. The RE current profile is reconstructed for the first time using the spatially resolved RE energy distribution. It is found to be more peaked than the pre-disruption plasma current, with higher internal inductance, suggesting preferential formation of REs in the core plasma or potentially a radially inward motion of the REs. The accessed relatively low-current (180 kA) RE beam is found stable, likely due to its elevated q profile. From this base stable equilibrium, instability is accessed by ramping the solenoid current. Under a large applied accelerating loop voltage an internal kink mode is observed. The kink mode leads to sawtooth-like relaxation of the RE current profile, but drives no RE loss. Under conditions of a large decelerating voltage, chirping Alfvénic instabilities driven by REs during the RE plateau stage are observed for the first time. The low-frequency (0.1{7 MHz) Alfvénic instabilities, supposedly compressional Alfvén eigenmodes, are found to be correlated with a RE loss signal. Finally, this provides novel plasma conditions to study these instabilities and investigate opportunities to utilize them for RE control. Bifurcated electron cyclotron emission (ECE) spectrum is measured during the collisionless RE plateau, with a break point at ≈100 GHz suggesting resonant absorption of the ECE at low frequencies.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Gravitational perturbations from oscillons and transients after inflation

We study the scalar and tensor perturbations generated by the fragmentation of the inflaton condensate into oscillons or transients after inflation, using nonlinear classical lattice simulations. Without including the backreaction of metric perturbations, we find that the magnitude of scalar metric perturbations never exceeds a few ×10 -3 , whereas the maximal strength of the gravitational wave signal today is $O$(10 -9 ) for standard post-inflationary expansion histories. We provide parameter scalings for the α-attractor models of inflation, which can be easily applied to other models. We also discuss the likelihood of primordial black hole formation, as well as conditions under which the gravitational wave signal can be at observationally interesting frequencies and amplitudes. Finally, we provide an upper bound on the frequency of the peak of the gravitational wave signal, which applies to all preheating scenarios.

79 ASTRONOMY AND ASTROPHYSICS↗

An elastin-like polymer targeting vascular endothelial growth factor receptor-1 reduces survival in serum-starved endothelial cells

Peptides often exhibit biological activity that depends on the context in which they are displayed and delivered. Understanding and controlling these contextual effects on peptide function is critical for designing targeted and responsive peptide-based biomaterials and therapeutics. Genetically engineered protein polymers such as elastin-like polypeptides (ELPs) can incorporate bioactive peptide motifs and are attractive candidates for biomaterials used in tissue engineering and targeted drug delivery. They also present an opportunity for investigating and modulating cell signaling pathways by presenting a peptide ligand in various defined chemical and physical environments. Vascular endothelial growth factor receptor-1 (VEGFR1) signaling plays important and complex roles in cell survival and angiogenesis, but polymeric materials that interact with this signaling axis are scarce. In this study, a novel genetically engineered elastin-like polymer that targets VEGFR1 is characterized. This polymer, termed R1B-ELP, binds to human endothelial cells in a manner dependent on its VEGFR1-targeting motif and, based on cell proliferation and cytotoxicity assays, demonstrates activity consistent with disrupting pro-survival signaling necessary for endothelial cell function under conditions of environmental stress. Notably, these findings indicate that ELP fusion alters the functional behavior of the targeting peptide. Modulators of VEGFR1 signaling have potential applications in basic studies of angiogenesis as well as in therapeutic applications targeting vascular or inflammatory diseases.

36 MATERIALS SCIENCE↗

Discriminating cascading processes in nonlinear optics: A QED analysis based on their molecular and geometric origin

The nonlinear optical response of a system of molecules often contains contributions whereby the products of lower-order processes in two separate molecules give signals that appear on top of a genuine direct higher-order process with a single molecule. These many-body contributions are known as cascading and complicate the interpretation of multidimensional stimulated Raman and other nonlinear signals. In a quantum electrodynamic treatment, these cascading processes arise from second-order expansion in the molecular coupling to vacuum modes of the radiation field, i.e., single-photon exchange between molecules, which also gives rise to other collective effects. Furthermore, we predict the relative phase of the direct and cascading nonlinear signals and its dependence on the microscopic dynamics as well as the sample geometry. This phase may be used to identify experimental conditions for distinguishing the direct and cascading signals by their phase. Higher-order cascading processes involving the exchange of several photons between more than two molecules are discussed.

74 ATOMIC AND MOLECULAR PHYSICS↗

Low-background InSb array development

Photovoltaic indium antimonide (PV InSb) detector technology has matured over the past several years to enable a wide variety of applications to use this high-performance detector material to advantage. The operating conditions for most of the applications to date for back-side illuminated PV InSb arrays have encompassed focal plane temperatures ranging from 40 to approximately 95 K, with the majority in the narrower range between 60 and 80 K. Background flux conditions have ranged from 10 to the 10th power ph/sq cm/sec to 10 to the 16th power ph/sq cm/sec, most typically between 10 to the 12th power and 10 to the 14th power ph/sq cm/sec. Appropriately, the array parameters were optimized for maximum performance over these temperature and background ranges. The key parameters which were peaked in this process were the resistance-area product of the detectors and their quantum efficiency. The Space Infrared Telescope Facility (SIRTF) Infrared Array Camera requirements, however, present very low temperature and background operating conditions, plus the need for very high signal to noise ratios. Preliminary analysis indicates that back-side illuminated PV InSb arrays can be optimized for operation under these conditions, and some performance projections will be presented.

Thom, R. D.↗

Surface-Enhanced Raman Detection of the CO 2 Moisture Swing

The development of scalable, energy-efficient carbon dioxide (CO 2 ) capture technologies is critical for achieving net-zero emissions. Moisture swing (MS) sorbents offer a promising alternative to traditional thermal regeneration methods by enabling reversible CO 2 binding through humidity-driven ion hydrolysis. In this study, we investigate the anion speciation dynamics in two classes of MS materials─an anion-exchange resin with a bicarbonate anion and activated carbon impregnated with potassium bicarbonate salt─using both sorption measurements and in situ surface-enhanced Raman spectroscopy (SERS). Ni-coated Ag nanowires were employed as SERS substrates to enhance signal intensity and enable the real-time detection of carbonate (CO 3 2– ), bicarbonate (HCO 3 – ), and hydroxide (OH – ) species under controlled humidity conditions in both air and nitrogen atmospheres. The results reveal humidity-dependent interconversion between anionic species with significant spectral shifts confirming the reversible hydrolysis reactions that drive the MS mechanism. Under humid conditions, we observed the depletion of bicarbonate signals and a concurrent increase in carbonate species, consistent with moisture-induced desorption of CO 2 . With the activated carbon samples, we further observed the formation of hydroxide. These findings not only validate the mechanistic models of humidity-driven anion exchange in MS sorbents but also demonstrate the practical potential of SERS as an operando diagnostic tool for monitoring CO 2 capture media. The ability to resolve and semiquantitatively evaluate the reversible transformation of carbonate, bicarbonate, and hydroxide ions under realistic environmental conditions provides valuable insight for the rational design, performance optimization, and quality control of next-generation sorbent materials for direct air capture applications.

CO2 capture↗

Leveraging transcription factors to speed cellobiose fermentation by Saccharomyces cerevisiae

Saccharomyces cerevisiae, a key organism used for the manufacture of renewable fuels and chemicals, has been engineered to utilize non-native sugars derived from plant cell walls, such as cellobiose and xylose. However, the rates and efficiencies of these non-native sugar fermentations pale in comparison with those of glucose. Systems biology methods, used to understand biological networks, hold promise for rational microbial strain development in metabolic engineering. Here, we present a systematic strategy for optimizing non-native sugar fermentation by recombinant S. cerevisiae, using cellobiose as a model. Differences in gene expression between cellobiose and glucose metabolism revealed by RNA deep sequencing indicated that cellobiose metabolism induces mitochondrial activation and reduces amino acid biosynthesis under fermentation conditions. Furthermore, glucose-sensing and signaling pathways and their target genes, including the cAMP-dependent protein kinase A pathway controlling the majority of glucose-induced changes, the Snf3-Rgt2-Rgt1 pathway regulating hexose transport, and the Snf1-Mig1 glucose repression pathway, were at most only partially activated under cellobiose conditions. To separate correlations from causative effects, the expression levels of 19 transcription factors perturbed under cellobiose conditions were modulated, and the three strongest promoters under cellobiose conditions were applied to fine-tune expression of the heterologous cellobiose-utilizing pathway. Of the changes in these 19 transcription factors, only overexpression of SUT1 or deletion of HAP4 consistently improved cellobiose fermentation. SUT1 overexpression and HAP4 deletion were not synergistic, suggesting that SUT1 and HAP4 may regulate overlapping genes important for improved cellobiose fermentation. Transcription factor modulation coupled with rational tuning of the cellobiose consumption pathway significantly improved cellobiose fermentation. We used systems-level input to reveal the regulatory mechanisms underlying suboptimal metabolism of the non-glucose sugar cellobiose. By identifying key transcription factors that cause suboptimal cellobiose fermentation in engineered S. cerevisiae, and by fine-tuning the expression of a heterologous cellobiose consumption pathway, we were able to greatly improve cellobiose fermentation by engineered S. cerevisiae. Our results demonstrate a powerful strategy for applying systems biology methods to rapidly identify metabolic engineering targets and overcome bottlenecks in performance of engineered strains.

09 BIOMASS FUELS↗

Interaction of electromagnetic and acoustic waves in a stochastic atmosphere

In the Stanford radio acoustic sounding system (RASS) an electromagnetic signal is made to scatter from a moving acoustic pulse train. Under a Bragg-scatter condition maximum electromagnetic scattering occurs. The scattered radio signal contains temperature and wind information as a function of the acoustic-pulse position. In this investigation RASS performance is assessed in an atmosphere characterized by the presence of turbulence and mean atmospheric parameters. The only assumption made is that the electromagnetic wave is not affected by stochastic perturbations in the atmosphere. It is concluded that the received radio signal depends strongly on the intensity of turbulence for altitudes of the acoustic pulse greater than the coherence length of propagation. The effect of mean vertical wind and mean temperature on the strength of the received signal is also demonstrated to be insignificant. Mean horizontal winds, however, shift the focus of the reflected electromagnetic energy from its origin, resulting in a decrease in received signal level when a monostatic radio-frequency (RF) system is used. For a bistatic radar configuration with space diversified receiving antennas, the shifting of the acoustic pulse makes possible the remote measurement of the horizontal wind component.

Bhatnagar, N.↗

An experimental study of the temporal statistics of radio signals scattered by rain

A fixed-beam bistatic CW experiment designed to measure the temporal statistics of the volume reflectivity produced by hydrometeors at several selected altitudes, scattering angles, and at two frequencies (3.6 and 7.8 GHz) is described. Surface rain gauge data, local meteorological data, surveillance S-band radar, and great-circle path propagation measurements were also made to describe the general weather and propagation conditions and to distinguish precipitation scatter signals from those caused by ducting and other nonhydrometeor scatter mechanisms. The data analysis procedures were designed to provide an assessment of a one-year sample of data with a time resolution of one minute. The cumulative distributions of the bistatic signals for all of the rainy minutes during this period are presented for the several path geometries.

Hubbard, R. W.↗