Teleoperation, Telerobotics
In a general sense, teleoperator devices enable human operators to remotely perform mechanical actions that usually are performed by the human arm and hand.
applications↗
SEARCH · Engineering Papers
Results for “Remote operations”
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
AERCam Autonomy: Intelligent Software Architecture for Robotic Free Flying Nanosatellite Inspection Vehicles
The NASA Johnson Space Center has developed a nanosatellite-class Free Flyer intended for future external inspection and remote viewing of human spacecraft. The Miniature Autonomous Extravehicular Robotic Camera (Mini AERCam) technology demonstration unit has been integrated into the approximate form and function of a flight system. The spherical Mini AERCam Free Flyer is 7.5 inches in diameter and weighs approximately 10 pounds, yet it incorporates significant additional capabilities compared to the 35-pound, 14-inch diameter AERCam Sprint that flew as a Shuttle flight experiment in 1997. Mini AERCam hosts a full suite of miniaturized avionics, instrumentation, communications, navigation, power, propulsion, and imaging subsystems, including digital video cameras and a high resolution still image camera. The vehicle is designed for either remotely piloted operations or supervised autonomous operations, including automatic stationkeeping, point-to-point maneuvering, and waypoint tracking. The Mini AERCam Free Flyer is accompanied by a sophisticated control station for command and control, as well as a docking system for automated deployment, docking, and recharge at a parent spacecraft. Free Flyer functional testing has been conducted successfully on both an airbearing table and in a six-degree-of-freedom closed-loop orbital simulation with avionics hardware in the loop. Mini AERCam aims to provide beneficial on-orbit views that cannot be obtained from fixed cameras, cameras on robotic manipulators, or cameras carried by crewmembers during extravehicular activities (EVA s). On Shuttle or International Space Station (ISS), for example, Mini AERCam could support external robotic operations by supplying orthogonal views to the intravehicular activity (IVA) robotic operator, supply views of EVA operations to IVA and/or ground crews monitoring the EVA, and carry out independent visual inspections of areas of interest around the spacecraft. To enable these future benefits with minimal impact on IVA operators and ground controllers, the Mini AERCam system architecture incorporates intelligent systems attributes that support various autonomous capabilities. 1) A robust command sequencer enables task-level command scripting. Command scripting is employed for operations such as automatic inspection scans over a region of interest, and operator-hands-off automated docking. 2) A system manager built on the same expert-system software as the command sequencer provides detection and smart-response capability for potential system-level anomalies, like loss of communications between the Free Flyer and control station. 3) An AERCam dynamics manager provides nominal and off-nominal management of guidance, navigation, and control (GN&C) functions. It is employed for safe trajectory monitoring, contingency maneuvering, and related roles. This paper will describe these architectural components of Mini AERCam autonomy, as well as the interaction of these elements with a human operator during supervised autonomous control.
Fredrickson, Steven E.↗
Lunabotics Mining: Evolution of ARTEMIS PRIME
This slide presentation reviews the development of Amassing Regolith with Topper Engineers eMploying Innovative Solutions (ARTEMIS) in a competition to develop robotic lunar mining capabilities. The goal of the competition was to design, build and operate a remotely controlled device that is capable of excavating, transporting and discharging lunar regolith simulant in a lunar environment over a 13 minute period.
Bertke, Sarah↗
Tracking Positions and Attitudes of Mars Rovers
The Surface Attitude Position and Pointing (SAPP) software, which runs on computers aboard the Mars Exploration Rovers, tracks the positions and attitudes of the rovers on the surface of Mars. Each rover acquires data on attitude from a combination of accelerometer readings and images of the Sun acquired autonomously, using a pointable camera to search the sky for the Sun. Depending on the nature of movement commanded remotely by operators on Earth, the software propagates attitude and position by use of either (1) accelerometer and gyroscope readings or (2) gyroscope readings and wheel odometry. Where necessary, visual odometry is performed on images to fine-tune the position updates, particularly on high-wheel-slip terrain. The attitude data are used by other software and ground-based personnel for pointing a high-gain antenna, planning and execution of driving, and positioning and aiming scientific instruments.
Ali, Khaled↗
Software Implements a Space-Mission File-Transfer Protocol
CFDP is a computer program that implements the CCSDS (Consultative Committee for Space Data Systems) File Delivery Protocol, which is an international standard for automatic, reliable transfers of files of data between locations on Earth and in outer space. CFDP administers concurrent file transfers in both directions, delivery of data out of transmission order, reliable and unreliable transmission modes, and automatic retransmission of lost or corrupted data by use of one or more of several lost-segment-detection modes. The program also implements several data-integrity measures, including file checksums and optional cyclic redundancy checks for each protocol data unit. The metadata accompanying each file can include messages to users application programs and commands for operating on remote file systems.
Rundstrom, Kathleen↗
Solar Array Panels With Dust-Removal Capability
It has been proposed to incorporate piezoelectric vibrational actuators into the structural supports of solar photovoltaic panels, for the purpose of occasionally inducing vibrations in the panels in order to loosen accumulated dust. Provided that the panels were tilted, the loosened dust would slide off under its own weight. Originally aimed at preventing obscuration of photovoltaic cells by dust accumulating in the Martian environment, the proposal may also offer an option for the design of solar photovoltaic panels for unattended operation at remote locations on Earth. The figure depicts a typical lightweight solar photovoltaic panel comprising a backside grid of structural spars that support a thin face sheet that, in turn, supports an array of photovoltaic cells on the front side. The backside structure includes node points where several spars intersect. According to the proposal, piezoelectric buzzers would be attached to the node points. The process of designing the panel would be an iterative one that would include computational simulation of the vibrations by use of finite- element analysis to guide the selection of the vibrational frequency of the actuators and the cross sections of the spars to maximize the agitation of dust.
Dawson, Stephen↗
Energy Systems Test Area (ESTA) Pyrotechnic Operations: User Test Planning Guide
The Johnson Space Center (JSC) has created and refined innovative analysis, design, development, and testing techniques that have been demonstrated in all phases of spaceflight. JSC is uniquely positioned to apply this expertise to components, systems, and vehicles that operate in remote or harsh environments. We offer a highly skilled workforce, unique facilities, flexible project management, and a proven management system. The purpose of this guide is to acquaint Test Requesters with the requirements for test, analysis, or simulation services at JSC. The guide includes facility services and capabilities, inputs required by the facility, major milestones, a roadmap of the facility s process, and roles and responsibilities of the facility and the requester. Samples of deliverables, facility interfaces, and inputs necessary to define the cost and schedule are included as appendices to the guide.
Hacker, Scott↗
Optimization of the Multi-Spectral Euclidean Distance Calculation for FPGA-based Spaceborne Systems
Due to the high quantity of operations that spaceborne processing systems must carry out in space, new methodologies and techniques are being presented as good alternatives in order to free the main processor from work and improve the overall performance. These include the development of ancillary dedicated hardware circuits that carry out the more redundant and computationally expensive operations in a faster way, leaving the main processor free to carry out other tasks while waiting for the result. One of these devices is SpaceCube, a FPGA-based system designed by NASA. The opportunity to use FPGA reconfigurable architectures in space allows not only the optimization of the mission operations with hardware-level solutions, but also the ability to create new and improved versions of the circuits, including error corrections, once the satellite is already in orbit. In this work, we propose the optimization of a common operation in remote sensing: the Multi-Spectral Euclidean Distance calculation. For that, two different hardware architectures have been designed and implemented in a Xilinx Virtex-5 FPGA, the same model of FPGAs used by SpaceCube. Previous results have shown that the communications between the embedded processor and the circuit create a bottleneck that affects the overall performance in a negative way. In order to avoid this, advanced methods including memory sharing, Native Port Interface (NPI) connections and Data Burst Transfers have been used.
Cristo, Alejandro↗
JWST Lifting System
A document describes designing, building, testing, and certifying a customized crane (Lifting Device LD) with a strong back (cradle) to facilitate the installation of long wall panels and short door panels for the GHe phase of the James Webb Space Telescope (JWST). The LD controls are variable-frequency drive controls designed to be adjustable for very slow and very-short-distance movements throughout the installation. The LD has a lift beam with an electric actuator attached at the end. The actuator attaches to a rectangular strong back (cradle) for lifting the long wall panels and short door panels from a lower angle into the vertical position inside the chamber, and then rotating around the chamber for installation onto the existing ceiling and floor. The LD rotates 360 (in very small increments) in both clockwise and counterclockwise directions. Eight lifting pads are on the top ring with 2-in. (.5-cm) eye holes spaced evenly around the ring to allow for the device to be suspended by three crane hoists from the top of the chamber. The LD is operated by remote controls that allow for a single, slow mode for booming the load in and out, with slow and very slow modes for rotating the load.
Tolleson, William↗
Human Factors of Remotely Piloted Aircraft
The civilian use of remotely piloted, or unmanned aircraft is expected to increase rapidly in the years ahead. Despite being referred to as unmanned some of the major challenges confronting this emerging sector relate to human factors. As unmanned aircraft systems (UAS) are introduced into civil airspace, a failure to adequately consider human factors could result in preventable accidents that may not only result in loss of life, but may also undermine public confidence in remotely piloted operations. Key issues include pilot situational awareness, collision avoidance in the absence of an out-the-window view, the effects of time delays in communication and control systems, control handovers, the challenges of very long duration flights, and the design of the control station. Problems have included poor physical layout of controls, non-intuitive automation interfaces, an over-reliance on text displays, and complicated sequences of menu selection to perform routine tasks. Some of the interface problems may have been prevented had an existing regulation or cockpit design principle been applied. In other cases, the design problems may indicate a lack of suitable guidance material.
unmanned aircraft systems↗
Design, Development and Testing of the Miniature Autonomous Extravehicular Robotic Camera (Mini AERCam) Guidance, Navigation and Control System
Engineers at NASA Johnson Space Center have designed, developed, and tested a nanosatellite-class free-flyer intended for future external inspection and remote viewing of human spaceflight activities. The technology demonstration system, known as the Miniature Autonomous Extravehicular Robotic Camera (Mini AERCam), has been integrated into the approximate form and function of a flight system. The primary focus has been to develop a system capable of providing external views of the International Space Station. The Mini AERCam system is spherical-shaped and less than eight inches in diameter. It has a full suite of guidance, navigation, and control hardware and software, and is equipped with two digital video cameras and a high resolution still image camera. The vehicle is designed for either remotely piloted operations or supervised autonomous operations. Tests have been performed in both a six degree-of-freedom closed-loop orbital simulation and on an air-bearing table. The Mini AERCam system can also be used as a test platform for evaluating algorithms and relative navigation for autonomous proximity operations and docking around the Space Shuttle Orbiter or the ISS.
Wagenknecht, J.↗
Transitioning NASA and NOAA Satellite Products, Modeling Data Assimilation Techniques, and Nowcasting Tools to Operations
No abstract available
research-to-operations↗
Pilot Situation Awareness and Its Implications for Single Pilot Operations: Analysis of a Human-In-The-Loop Study
In 2012, NASA began exploring the feasibility of single pilot/reduced crew operations in the context of scheduled air carrier operations. The current study examined how important it was for ground-based personnel providing support to single piloted aircraft (ground operators) to have opportunities to acquire situation awareness (SA) prior to being called on to assist an aircraft. We looked at two distinct concepts of operation, which varied in how much information was available to ground operators prior to being called on to assist a critical event (no vs. some Situation Preview). Thirty-five commercial pilots participated in the current study. Results suggested that a ground operators’ lack of initial SA when called on for dedicated assistance is not an issue, at least when the ground operator station displays environmental and systems data which are important to gaining overall SA of the specified aircraft. With appropriate displays, ground operators were able to provide immediate assistance, even if they had minimal SA prior to getting a request.
Reduced crew operations↗
Exploration Ground Data Systems (xGDS) Overview
xGDS supports rapid scientific decision making by synchronizing the time and mapped location of observation notes, instrument data, photos, video, samples and other data. xGDS is a suite of web tools, developed at NASA Ames Research Center to support remote science operations in analog missions and prototype new ideas for planetary exploration. During operations, xGDS displays science data in real-time with geographic context, supporting key decisions (e.g. sample site selection). Post-operations, xGDS enables efficient analysis of data by correlating data products in time and on the map. xGDS has been developed in close collaboration with science teams since 2009, and used enthusiastically by upwards of 100 scientists to support scientific field research and data analysis.
Ground Data System↗
The International Space Station (ISS) Port 1 (P1) External Active Thermal Control System (EATCS) Ammonia Leak
Ammonia is used in the Starboard 1 (S1) and Port 1 (P1) External Active Thermal Control System (EATCS) to cool the pressurized modules, and some of the external electrical power distribution hardware. Leaks that develop in these critical cooling systems that deplete in-line tanks can ultimately result in loss of cooling, which can have devastating impacts to the mission, science and crew onboard the ISS. A slow ammonia leak was initially observed from the P1 EATCS in 2011, but later in 2013 the leak rate began to accelerate. The ammonia inventory eventually began to decay exponentially, raising concerns that the inventory could drop to levels where the system would not be operational.The Robotic External Leak Locator (RELL) was built and launched to the ISS to detect and help locate ammonia leaks using the ISS Robotic Arm and remote ground operator control without constant crew involvement. RELL pinpointed the ammonia leak to the two flexible jumper hose assemblies connecting one of two fluid loops in one of the three deployable radiators to the P1 EATCS. The ammonia inside the two hose assemblies and that radiator fluid loop was isolated and vented to space in 2017. This stopped the leak and an Extravehicular Activity was conducted to remove the two hose assemblies so they could be returned to ground for further Test, Teardown and Evaluation (TT&E). The purpose of this presentation is to discuss this leakage scenario and the TT&E efforts.
Cowan, Darnell T.↗
Advanced Inspection System: Integrating Robotic Configurations & Controls
The Advanced Inspection System (AIS) promotes the ability to perform field inspections and repairs remotely by operator command. The robotic system is required to be a fully autonomous operation, managed by computer execution of scripts with limited user control. AIS is a complex yet intriguing challenge in which various goals must be reached to achieve complete autonomy. The first steps to building such a system require human computer interactions and computer simulations for testing and verification. Such applications include the use of a wireless video game controller via Bluetooth Technology and the use of Leap Motion, a gesture based motion controller which can be used to manipulate robotic arm movements. Utilizing the Robotic Operating System (ROS) environment, these applications, in accordance to developing a 3D simulation of the system, will provide a foundational test bed for AIS development.
Wlodarczyk, Stephan J.↗
High Flying Interns: NASA's Student Airborne Research Program
The NASA Student Airborne Research Program is an annual summer internship for upper-level undergraduate STEM majors. Each summer since 2009, we have competitively selected ~30 undergraduates from colleges and universities across the United States for this unique airborne research experience. In all past summers, students flew onboard a NASA research aircraft where they assisted in the operation of remote sensing and in situ instrumentation to study the Earth, ocean, and atmosphere. Students also participated in field trips where they acquired data to ground-truth and complement the airborne data. After their flights and field trips, students then spent the rest of summer developing individual research projects using the data they collected as well as data from previous year SARP flights, other NASA airborne campaigns, and NASA satellite data. This summer, we adapted the program to be entirely online. Each of the 28 undergraduate students still completed an individual research project using data from previous SARP flights as well as publicly available data from other airborne campaigns, satellites, and/or ground stations. Students were mentored remotely by five university faculty members, five graduate students, and several additional scientists and engineers from NASA. In order to preserve some aspects of the hands-on research experience, we also shipped each student a box of twenty-four Whole Air Sampling canisters identical to what they would have used to collect air samples onboard the NASA aircraft. Instead, each student collected ground samples near their home starting in mid-April through July. The goal of this sampling was to attempt to characterize the impacts of pandemic-related changes in emissions with time across the United States. The results of that ground sampling are being presented in scientific sessions in this meeting. In addition, students also measured PM2.5 and aerosol optical depth from June through August using sensors provided by the Citizen-Enabled Aerosol Measurements for Satellites (CEAMS) at Colorado State University. We will discuss strategies we employed to conduct research online, the unexpected opportunities that arose, and lessons learned.
STEM disciplines↗