Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Reflector Antennas”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS1985

Estimating Antenna Shape From Far-Field Measurements

Amplitude and phase measurements help characterize nearly paraboloidal reflectors. Deviation of microwave reflector from ideal paraboloidal shape deduced from far-field amplitude and phase measurements with help of theoretical technique referred to as microwave holographic metrology. Technique enables estimation of antenna-surface figure from measurements taken at prescribed number of field points. After determining amount of surface deviation, performance of antenna then improved by properly adjusting surface panels.

Rahmat-Samii, Y.↗
NASA NTRS1986

Surface control system for the 15 meter hoop-column antenna

The 15-meter hoop-column antenna fabricated by the Harris Corporation under contract to the NASA Langley Research Center is described. The antenna is a deployable and restowable structure consisting of a central telescoping column, a 15-meter-diameter folding hoop, and a mesh reflector surface. The hoop is supported and positioned by 48 quartz cords attached to the column above the hoop, and by 24 graphite cords from the base of the antenna column. The RF reflective surface is a gold plated molybdenum wire mesh supported on a graphite cord truss structure which is attached between the hoop and the column. The surface contour is controlled by 96 graphite cords from the antenna base to the rear of the truss assembly. The antenna is actually a quadaperture reflector with each quadrant of the surface mesh shaped to produce an offset parabolic reflector. Results of near-field and structural tests are given. Controls structures and electromagnetics interaction, surface control system requirements, mesh control adjustment, surface control system actuator assembly, surface control system electronics, the system interface unit, and control stations are discussed.

Miller, James B.↗
NASA NTRS1963

Antennas.

Antenna design characteristics evaluated in terms of communications system design

ANTENNA↗
NASA NTRS1976

Advanced microwave radiometer antenna system study

The practicability of a multi-frequency antenna for spaceborne microwave radiometers was considered in detail. The program consisted of a comparative study of various antenna systems, both mechanically and electronically scanned, in relation to specified design goals and desired system performance. The study involved several distinct tasks: definition of candidate antennas that are lightweight and that, at the specified frequencies of 5, 10, 18, 22, and 36 GHz, can provide conical scanning, dual linear polarization, and simultaneous multiple frequency operation; examination of various feed systems and phase-shifting techniques; detailed analysis of several key performance parameters such as beam efficiency, sidelobe level, and antenna beam footprint size; and conception of an antenna/feed system that could meet the design goals. Candidate antennas examined include phased arrays, lenses, and optical reflector systems. Mechanical, electrical, and performance characteristics of the various systems were tabulated for ease of comparison.

Kummer, W. H.↗
NASA NTRS1980

Solar power satellite offshore rectenna study

Offshore rectennas are feasible and cost competitive with land rectennas but the type of rectenna suitable for offshore use is quite different from that specified in the present reference system. A nonground plane design minimizes the weight and greatly reduces the number of costly support towers. This perferred design is an antenna array consisting of individually encapsulated dipoles with reflectors or tagis supported on feed wires. Such a 5 GW rectenna could be built at a 50 m water depth site to withstand hurricane, winter storm, and icing conditions for a one time cost of $5.7 billion. Subsequent units would be about 1.3 less expensive. More benign and more shallow water sites would result in substantially lower costs. The major advantage of an offshore rectenna is the removal of microwave radiation from populated areas.

Source record↗
NASA NTRS1980

Solar power satellite offshore rectenna study

It was found that an offshore rectenna is feasible and cost competitive with land rectennas but that the type of rectenna which is suitable for offshore use is quite different from that specified in the present reference system. The result is a nonground plane design which minimizes the weight and greatly reduces the number of costly support towers. This preferred design is an antenna array consisting of individually encapsulated dipoles with reflectors supported on feed wires. Such a 5 GW rectenna could be built at a 50 m water depth site to withstand hurricane and icing conditions for a one time cost of 5.7 billion dollars. Subsequent units would be about 1/3 less expensive. The east coast site chosen for this study represents an extreme case of severe environmental conditions. More benign and more shallow water sites would result in lower costs. Secondary uses such as mariculture appear practical with only minor impact on the rectenna design. The potential advantages of an offshore rectenna, such as no land requirements, removal of microwave radiation from populated areas and minimal impact on the local geopolitics argue strongly that further investigation of the offshore rectenna should be vigorously pursued.

Source record↗
NASA NTRS1981

A modular approach toward extremely large apertures

Modular antenna construction can provide a significant increase in reflector aperture size over deployable reflectors. The modular approach allows reflective mesh surfaces to be supported by a minimum of structure. The kinematics of the selected deployable design approach were validated by the subscale demonstration model. Further design refinements on the module structural/joints and design optimization on intermodule joints are needed.

Woods, A. A., Jr.↗
NASA NTRS1982

Radar scatterometry of sand dunes and lava flows

Four frequency like polarized scatterometer data over a sand dune field and a volcanic field were analyzed to understand the scattering characteristics of these two terrain types as a function of frequency and incidence angle. For the frequency range studied (400 MHz to 13.3 GHz) unvegetated sand dunes are specular reflectors that return an echo to the radar antenna particularly when the geometry is such that the dune slope is nearly perpendicular to the antenna. Vegetation on the dunes can cause significant backscatter. Lava flows are strong diffuse scatterers which have backscatter values similar to coniferous forest at certain frequencies. Different observation frequencies are required for different situations. The scatterometer data correlate well with radar images.

Blom, R.↗
NASA NTRS1992

Preliminary test results and upgrades for an automated assembly system

An automated structures assembly testbed developed by Langley Research Center to study the practical problems associated with the automated assembly of large space structures using robotic manipulators is described. Emphasis is placed on the requirements and features of system upgrades and their impact on system performance, flexibility, and reliability. The current research program is aimed at evolving the baseline assembly system into a flexible, robust, sensor-based system capable of assembling more complex truss-supported satellite systems. To achieve this objective, five system upgrades have been developed including a machine vision capability to eliminate taught robot arm positions; an on-board end-effector microprocessor to reduce communications; a second-generation end-effector to construct contoured trusses for antennas and install payloads; the installation of reflector-type panels on the truss to produce a complete and functional system, and an expert system to significantly reduce the amount of software code required for system operation and provide greater flexibility in implementing new features.

Will, Ralph W.↗
NASA NTRS2003

Advanced precipitation radar antenna

In this paper, the technology development status on this Advanced Precipitation Radar Antenna will be presented.

antenna precipitation radar inflatable reflector m↗
NASA NTRS2002

Major technological innovations introduced in the large antennas of the Deep Space Network

The NASA Deep Space Network (DSN) is the largest and most sensitive scientific, telecommunications and radio navigation network in the world. Its principal responsibilities are to provide communications, tracking, and science services to most of the world's spacecraft that travel beyond low Earth orbit. The network consists of three Deep Space Communications Complexes. Each of the three complexes consists of multiple large antennas equipped with ultra sensitive receiving systems. A centralized Signal Processing Center (SPC) remotely controls the antennas, generates and transmits spacecraft commands, and receives and processes the spacecraft telemetry.

large antennas beam waveguide dual reflector shapi↗
NASA NTRS2011

Aquarius Instrument and Salinity Retrieval

Aquarius has been designed to map the surface salinity field of the global ocean from space a parameter important for understanding ocean circulation and its relationship to climate and the global water cycle. Salinity is measured remotely from space by measuring the thermal emission from the ocean surface. This is done at the low frequency end of the microwave spectrum (e.g. 1.4 GHz) where the emission is sufficiently sensitive to changes in salinity to be detected with sophisticated radiometers. The goal is to monitor the seasonal and interannual variation of the large scale features of the surface salinity field in the open ocean by providing maps on a monthly basis with a spatial resolution of 150 km and an accuracy of 0.2 psu. These are challenging requirements that have led to some unique features of the instrument. These include: a) The addition of a co-located scatterometer to help provide a correction for roughness; b) The addition of a polarimetric channel (third Stokes parameter) to the radiometer to help correct for Faraday rotation; c) Asun-synchronous orbit with a 6 pm ascending equatorial crossing to minimize Faraday rotation and with the antennas looking away from the sun toward the nighttime side to minimize contamination by radiation from the sun; and d) An antenna designed to limit side lobes in the direction of rays from the sun. In addition, achieving the accuracy goal of 0.2 psu requires averaging over one month and to do this requires a highly stable radiometer. Aquarius has three separate radiometers that image in pushbroom fashion with the three antenna beams looking across track. The antenna is a 2.5-m diameter, offset parabolic reflector with three feed horns and the three beams are arranged to image with the boresight aligned to look across track, roughly perpendicular to the spacecraft heading and pointing away from the Sun. The three beams point at angles of theta = 25.8 deg., 33.8 deg. and 40.3 deg. with respect to the spacecraft nadir which correspond to local incidence angles at the surface of 28.7 deg., 37.8 deg. and 45.6 deg., respectively. The resolution of the three radiometer beams (axes of the 3dB ellipse) is: 76 x 94 km for the inner beam, 84 x 120 km for the middle beam to 96 x 156 km for the outer beam. Together they cover a swath of about 390 km. Aquarius will map the global ice-free ocean every 7-days from which monthly average composites will be derived. This will provide a snapshot of the mean field, as well as resolving the seasonal to interannual variations over the three-year baseline of the mission.

Le Vine, D. M.↗
NASA NTRS2003

NASA Tech Briefs, June 2003

Topics covered include: Nulling Infrared Radiometer for Measuring Temperature; The Ames Power Monitoring System; Hot Films on Ceramic Substrates for Measuring Skin Friction; Probe Without Moving Parts Measures Flow Angle; Detecting Conductive Liquid Leaking from Nonconductive Pipe; Adaptive Suppression of Noise in Voice Communications; High-Performance Solid-State W-Band Power Amplifiers; Microbatteries for Combinatorial Studies of Conventional Lithium-Ion Batteries; Correcting for Beam Aberrations in a Beam-Waveguide Antenna; Advanced Rainbow Solar Photovoltaic Arrays; Metal Side Reflectors for Trapping Light in QWIPs; Software for Collaborative Engineering of Launch Rockets; Software Assists in Extensive Environmental Auditing; Software Supports Distributed Operations via the Internet; Software Estimates Costs of Testing Rocket Engines; yourSky: Custom Sky-Image Mosaics via the Internet; Software for Managing Inventory of Flight Hardware; Lower-Conductivity Thermal-Barrier Coatings; Process for Smoothing an Si Substrate after Etching of SiO2; Flexible Composite-Material Pressure Vessel; Treatment to Destroy Chlorohydrocarbon Liquids in the Ground; Noncircular Cross Sections Could Enhance Mixing in Sprays; Small, Untethered, Mobile Roots for Inspecting Gas Pipes; Paint-Overspray Catcher; Preparation of Regular Specimens for Atom Probes; Inverse Tomo-Lithography for Making Microscopic 3D Parts; Predicting and Preventing Incipient Flameout in Combustors; MEMS-Based Piezoelectric/Electrostatic Inchworm Actuator; Metallized Capillaries as Probes for Raman Spectroscopy; Adaptation of Mesoscale Weather Models to Local Forecasting; Aerodynamic Design using Neural Networks; Combining Multiple Gyroscope Outputs for Increased Accuracy; and Improved Collision-Detection Method for Robotic Manipulator.

Source record↗
DOE OSTI2023

Direct write sensors

A method of making an acoustic wave sensor includes the steps of providing a piezoelectric substrate layer and printing on the substrate layer a sensor layer comprising a first interdigitated acoustic wave transducer, a sensing film, and positioned on an opposing side of the sensing film from the first interdigitated acoustic wave transducer at least one selected from the group consisting of a second interdigitated acoustic wave transducer and a Bragg reflector. An insulation layer can be printed. An antenna can be printed in an antenna layer, and the insulation layer can be interposed between the antenna layer and the sensor layer. An electrical connection can be printed between the antenna and the first interdigitated acoustic wave transducer. An acoustic wave sensor is also disclosed.

McIntyre, Timothy J.↗
NASA NTRS2010

A Novel Approach for a Low-Cost Deployable Antenna

The Naval Research Laboratory (NRL) has designed, built, and fully qualified a low cost, low Passive Intermodulation (PIM) 12-foot (3.66-m) diameter deployable ultra high frequency (UHF) antenna for the Tacsat-4 program. The design utilized novel approaches in reflector material and capacitive coupling techniques. This paper discusses major design trades, unique design characteristics, and lessons learned from the development of the Tacsat 4 deployable antenna. This antenna development was sponsored by the Office of Naval Research.

Amend, Chris↗
NASA NTRS1977

Dual-frequency feed system for 26-meter antenna conversion

New cassegrain feed cone assemblies were designed as part of the upgrade of three 26-meter diameter antennas to 34-meter diameter with improved performance. The new dual-frequency feed cone (SXD) will provide both S- and X-band feed systems and traveling wave masers, with a reflex reflector system to permit simultaneous operation analogous to the 64-meter antennas. Tasks involved in adding the X-band receiving capability and improving the S-band feed performance in support of Voyager and later missions described in.

Hartop, R. W.↗
NASA NTRS1980

The design and application of an antenna positioner mechanism for Intelsat-5 series communication satellite

In opertion, the East/West spot beam reflectors on the Intelsat-5 series communication satellite are required to satisfy initial precise-pointing to particular Earth locations; and repositioning and pointing to different Earth locations as traffic changes dictate during the seven year mission. Two 2 axis antenna positioner mechanisms (APM) are utilized in fulfilling these requirements. Each APM is comprised of three components which consist of one center pivot and two linear actuators rather than an integral two axis gimbal design. The step resolution of the APM can be adjusted as required with the present design, at a step resolution of 0.002865 degrees. The design philosophy and considerations, test program, and test results are discussed as well as some major problems encountered during the course of testing and their resolution.

Szeto, B.↗