Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “REACTOR FUEL”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Gear Test Assembly - Status Report For FY2019

The final stages of pre-sodium commissioning were completed for the Gear Test Assembly (GTA) in late 2018 and all the components were moved to building 308 for final preparations for insertion into the Mechanisms Engineering Test Loop (METL). The GTA was fully assembled in the experimental test assembly workstation and all supporting electrical and hardware systems were installed on the METL Mezzanine. The GTA was installed in Test Vessel 1 after performing a final systems check, and the vessel and article were raised to operating temperature and held for two weeks to bake-out any moisture present in the components. Test Vessel 1 was filled with sodium and a purification process was completed using the cold trap system. When the sodium was sufficiently clean, Test Vessel 1 was isolated from the rest of METL, and experimental operation of the GTA commenced. The experimental operations consisted of rotating two shafts using Parker servomotors to apply a prototypic torque of a fuel handling mechanism removing and inserting a sodium fast reactor fuel assembly. This removing and inserting motion was repeated until the system seized, indicating component degradation of either the gears or the bearings in the test gearbox. A total of 19,600 cycles were completed, corresponding to the removal and insertion of 9,800 fuel assemblies. The system was shut down and then prepared for removal. The Flexicask System was successfully used to remove the GTA from Test Vessel 1 while keeping both vessel and article inert during the process. The GTA was installed in the Carbonation System, where the process of slowly reacting the sodium away using moist CO 2 has been started. Once the GTA is fully cleaned, it will be disassembled and the gears will undergo the same NDE process performed before testing to quantify the wear that occurred. A report on this, along with the data analysis from the experimental operations will be submitted in late 2019.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

System impacts of accelerated transfer of used nuclear fuel to dry storage - 15220

In the wake of the September 11, 2001 terror attacks, and again after the March 11, 2011, accident at the Fukushima Dai-Ichi station from the Great East Japan Earthquake/tsunami, concern was expressed regarding security of current spent fuel storage practices in the United States. An approach recurrently proposed to reduce the potential for fire and the release of radionuclides in an accident or sabotage scenario is to reduce the loading of the reactor fuel pools, which are frequently maintained near their full capacity at many reactor sites in the U.S. We assess the impact on the waste management system of different scenarios for accelerating the schedule of used nuclear fuel (UNF) transfer from reactor pools to dry storage casks. We consider scenarios where the spent fuel pools are drawn down to 50% or 25% of full capacity over 5- or 10-year schedules. The scenarios include status quo, where UNF continues to remain in dry storage at the reactor sites, as well as scenarios with UNF transfer to interim storage and eventually to a mined geologic repository. The primary purpose is to evaluate how the different scenarios for accelerating the transfer of UNF to at-reactor dry storage would affect the performance of the entire UNF management system. Areas that were considered include an estimate of the additional system costs that could be incurred and where the existing infrastructure at the reactor sites would come under stress from the transfer demands. This study considered only the fuel-handling logistics and rough-order-of-magnitude cost at reactor sites, interim storage facility, and operations to package UNF into disposal canisters. The effects of minimum fuel age that could be transferred and the accelerated transfer starting date are also examined, but found to have relatively little effect. Impacts on safety and worker dose are not evaluated quantitatively, although effects can be inferred from increases in handling operations, etc. from the scenarios considered. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Multiple recycle of REMIX fuel based on reprocessed uranium and plutonium mixture in thermal reactors

REMIX fuel consumption in WWER-1000 is considered. REMIX fuel is fabricated from non-separated mixture of uranium and plutonium obtained during NPP spent fuel reprocessing with further makeup by enriched natural uranium. It makes possible to recycle several times the total amount of uranium and plutonium obtained from spent fuel with 100% loading of the WWER-1000 core. The stored SNF could be also involved in REMIX fuel cycle by enrichment of regenerated uranium. The same approach could be applied to closing the fuel cycle of CANDU reactors. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Silicon carbide and its composites for nuclear applications – Historical overview

The goal of achieving higher thermal efficiency in nuclear power systems, whether fission or fusion based, has invariably led to the study and development of refractory metals, ceramics, and their composites. Silicon carbide materials, owing to their favorable neutronic and high-temperature properties, have seen extensive study for over half a century in support of this goal. Currently, our community has a relatively deep understanding of the irradiation effects on this system and has developed irradiation-hardened materials that are currently in use for fission reactor fuels and available as structural composites for next generation reactors. Outside of the nuclear arena SiC has also enjoyed significant development with a wide range of ordinary and high-value product now in use including very high temperature commercial aerospace installations such as turbine engines. This overview presents a brief history of the development of SiC, focused on but not limited to irradiation applications that has led to our present understanding of the system for nuclear application.

36 MATERIALS SCIENCE↗

The Partitioning of Americium and the Lanthanides Using Tetrabutyldiglycolamide (TBDGA) in Octanol and in Ionic Liquid Solution

Separations among the lanthanides and the separation of Am from the lanthanides remain challenging, and research in this area continues to expand. The separation of adjacent lanthanides is of interest to high-tech industries because individual lanthanides have specialized uses and are in short supply. In nuclear fuel cycle applications Am would be incorporated into fast reactor fuels, yet the lanthanides are not desired. In this work the diamide N,N,N',N'-tetrabutyldiglycolamide (TBDGA) was investigated as a ligand for lanthanide and Am solvent extraction in both molecular and room temperature ionic liquid (RTIL) diluents. The RTIL [C4MIM][Tf2N-] showed very high extraction efficiency for these trivalent metals from low nitric acid concentrations, while the molecular diluent 1-octanol showed high extraction efficiency at high acid concentrations. This was attributed to the extraction of ionic nitrate complexes by the RTIL, whereas 1-octanol extracted neutral nitrate complexes. TBDGA in RTIL did not provide adequate separation factors for Am/lanthanide partitioning, but 1-octanol did show reasonable separation possibilities. Lanthanide intergroup separations appeared to be feasible in both diluents, but with higher separation factors from 1-octanol.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Evaluation of advanced combustion concepts for dry NO sub x suppression with coal-derived, gaseous fuels

The emissions performance of a rich lean combustor (developed for liquid fuels) was determined for combustion of simulated coal gases ranging in heating value from 167 to 244 Btu/scf (7.0 to 10.3 MJ/NCM). The 244 Btu/scf gas is typical of the product gas from an oxygen blown gasifier, while the 167 Btu/scf gas is similar to that from an air blown gasifier. NOx performance of the rich lean combustor did not meet program goals with the 244 Btu/scf gas because of high thermal NOx, similar to levels expected from conventional lean burning combustors. The NOx emissions are attributed to inadequate fuel air mixing in the rich stage resulting from the design of the large central fuel nozzle delivering 71% of the total gas flow. NOx yield from ammonia injected into the fuel gas decreased rapidly with increasing ammonia level, and is projected to be less than 10% at NH3 levels of 0.5% or higher. NOx generation from NH3 is significant at ammonia concentrations significantly less than 0.5%. These levels may occur depending on fuel gas cleanup system design. CO emissions, combustion efficiency, smoke and other operational performance parameters were satisfactory. A test was completed with a catalytic combustor concept with petroleum distillate fuel. Reactor stage NOx emissions were low (1.4g NOx/kg fuel). CO emissions and combustion efficiency were satisfactory. Airflow split instabilities occurred which eventually led to test termination.

Beebe, K. W.↗

Cleanup and Dismantling of Highly Contaminated Ventilation Systems Using Robotic Tools - 13162

The UP1 plant reprocessed nearly 20,000 tons of used natural uranium gas cooled reactor fuel coming from the first generation of civil nuclear reactors in France. Following operating incidents in the eighties, the ventilation system of the continuous dissolution line facility was shut down and replaced. Two types of remote controlled tool carriers were developed to perform the decontamination and dismantling operations of the highly contaminated ventilation duct network. The first one, a dedicated small robot, was designed from scratch to retrieve a thick powder deposit within a duct. The robot, managed and confined by two dedicated glove boxes, was equipped for intervention inside the ventilation duct and used for carrying various cleanup and inspection tools. The second type, consisting of robotic tools developed on the base of an industrial platform, was used for the clean-up and dismantling of the ventilation duct system. Depending on the type of work to be performed, on the shape constraints of the rooms and any equipment to be dismantled, different kinds of robotic tools were developed and installed on a Brokk 40 carrier. After more than ten years of ventilation duct D and D operations at the UP1 plant, a lot of experience was acquired about remote operations. The three main important lessons learned in terms of remote controlled operation are: characterizing the initial conditions as much as reasonably possible, performing non-radioactive full scale testing and making it as simple and modular as possible. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Graphite Waste Tank Cleanup and Decontamination under the Marcoule UP1 D and D Program - 13166

The UP1 plant in Marcoule reprocessed nearly 20,000 tons of used natural uranium gas cooled reactor fuel coming from the first generation of civil nuclear reactors in France. During more than 40 years, the decladding operations produced thousands of tons of processed waste, mainly magnesium and graphite fragments. In the absence of a French repository for the graphite waste, the graphite sludge content of the storage pits had to be retrieved and transferred into a newer and safer pit. After an extensive R and D program, the equipment and process necessary for retrieval operations were designed, built and tested. The innovative process is mainly based on the use of two pumps (one to capture and the other one to transfer the sludge) working one after the other and a robotic arm mounted on a telescopic mast. A dedicated process was also set up for the removal of the biggest fragments. The retrieval of the most irradiating fragments was a challenge. Today, the first pit is totally empty and its stainless steel walls have been decontaminated using gels. In the second pit, the sludge retrieval and transfer operations have been almost completed. Most of the non-pumpable graphite fragments has been removed and transferred to a new storage pit. After more than 6 years of operations in sludge retrieval, a lot of experience was acquired from which important 'lessons learned' could be shared. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Large Eddy Simulation of turbulent flow in rod bundle with spacer grids

Pressurized water nuclear reactor fuel assemblies are made of fuel rods held by spacer grids, which are the core components of the nuclear power plants. Hot fuel rods are cooled by the coolant water flow, and the spacer grids with mixing vanes distort the mainstream, producing the swirling flow which can enhance the heat transfer to improve CHF (Critical Heat Flux). Heat transfer between fuel rods and coolant is a crucial part of thermal-hydraulic analysis. For the purpose to improve the thermal hydraulic performance of the fuel assemblies, many experiments have been conducted to understand the flow structures and three-dimensional behaviors of the turbulence in the rod bundle sub-channels and then to optimize the design of the spacer grid. In the experimental work, which requires lots of efforts to get reliable data, LDA (Laser Doppler Anemometry) and PIV (Particle Image Velocimetry) are generally used to measure the velocity profile and turbulent intensity in the sub-channels. Computational Fluid Dynamics (CFD) is another useful way to study the characteristics of the detailed flow condition and heat transfer phenomena in the subchannels. The main issue of the single-phase CFD is to accurately predict the flow and turbulence characteristics. RANS method is generally used to simulate the induced lateral velocity and the heat transfer process. With the development of computer technology, some more precise but previously time-consuming turbulent models, such as LES (Large Eddy Simulation), are gradually used for the simulation of rod bundle flow with current advanced CPU resources. Ikeno and Kajishima explained the decay of swirling turbulent flow in the rod bundle using LES method. Benhamadouche acquired the turbulence induced forces on the central rod of the rod bundle through performing the LES of the flow downstream the spacer grid. Chang and Tavoularis conducted hybrid simulations with SAS SST and LES of a 5 x 5 rod bundle, and several vortices were identified in the vicinity of the vanes and the generation mechanisms, evolution progress and influence on the velocities of these vortices were clarified. In the paper we present CFD simulations of turbulent flow in rod bundle sub-channels with spacer grids of two different experiments. One is MATiS-H benchmark experiment with scaled spacer grids, which is conducted by KAERI, and is used as a CFD benchmark test, and the other is a 5 x 5 rod bundle with typical spacer grids using PIV technology, with the cooperation of Harbin Engineering University. The main objectives of the calculations are to validate LES methodology by the benchmark experiments.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Elevated temperature microcantilever testing of fresh U-10Mo fuel

Proliferation concerns are the driving force to reduce the enrichment of research reactor fuel from highly enriched fuel to lower levels of enriched fuel. One promising fuel alloy that would enable a reduction in enrichment without greatly diminishing fuel performance is Uranium with 10 wt. % Molybdenum (U-10 wt-% Mo). While there is a large amount of data available on the microstructure and thermal properties of this new fuel type currently there is insufficient data available on the mechanical properties. Small scale mechanical testing techniques can be used to evaluate the mechanical properties of the as-fabricated U-10 wt% Mo components at their intended operating temperature which should improve the accuracy of the input parameters employed by modelers. In this study the mechanical properties of a U-10 wt% Mo fuel meat sample taken from an as-fabricated fuel plate for a new fuel design were evaluated using in-situ scanning electron microscopy microcantilever testing under varying temperatures between room temperature and 200 °C.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Investigation of Fission Product Interaction with the SiC Containment Layer of High Turnup TRISO Fuel Particles

Tri-structural Isotropic (TRISO) encapsulated fuel particles are used in high-temperature gas-cooled nuclear reactors. Fuel performance is limited by the propensity of metallic fission products to be released under high temperature testing to simulate hypothesized accident scenarios. The current particle design consists of a 350 μm or 425 μm UO{sub 2} or UCO fuel kernel surrounded by a 100μm porous carbon buffer layer, a 40μm inner pyrolytic carbon (IPyC) layer, a 35μm high-density silicon carbide (SiC) layer, and a 40μm outer pyrolytic carbon (OPyC) layer. Of interest is the fission product interaction with the SiC layer, which provides the most structural support and is the main barrier to the diffusion of fission products. Previous laboratory examination studies have indicated the release of Ag through seemingly intact particles and the localized corrosion of the SiC due to Pd. Although a number of studies have been conducted, the specifics of both the Ag and Pd reaction mechanisms, in addition to U and Pu, through SiC are currently not well understood. This work aims to understand the pathways and kinetics of these interactions under normal operation as well as accident conditions. In order to improve our understanding of this, we have the unique opportunity to examine irradiated TRISO particles to study post-irradiation effects on these materials. Experimental data is necessary to constrain the current models used to predict the behavior of fission products in the SiC layer of TRISO fuels. This work aims to understand the interaction of fission products with the SiC containment layer in TRISO particles. We have systematically examined three SiC shells from irradiated TRISO particles using XAFS, TEM, and EDS. Results indicate the formation of palladium silicides, and uranium and plutonium carbides. Additionally, silver is seen to be metallic. Preliminary microscopy results indicate fission products throughout the SiC layer of the TRISO particles, and microstructural changes have been observed between the as-irradiated and safety tested particles. These results have provided key information on the fission product transport behavior through irradiated SiC at varying temperatures. Knowledge of these reaction pathways will allow for better simulation of the long-term behavior of TRISO fuels. They may also suggest ways to modify the SiC layer to improve fuel performance and mitigate fission product release, which is critical for safety strategies required to commercialize these nuclear fuel technologies. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Development of a Safeguards Verification Method and Instrument to Detect Pin Diversion from Pressurized Water Reactor (PWR) Spent Fuel Assemblies Phase I Study

A novel methodology to detect diversion of spent fuel from Pressurized Water Reactors (PWR) has been developed in order to address a long unsolved safeguards verification problem for international safeguards community such as International Atomic Energy Agency (IAEA) or European Atomic Energy Community (EURATOM). The concept involves inserting tiny neutron and gamma detectors into the guide tubes of a spent fuel assembly and measuring the signals. The guide tubes form a quadrant symmetric pattern in the various PWR fuel product lines and the neutron and gamma signals from these various locations are processed to obtain a unique signature for an undisturbed fuel assembly. Signatures based on the neutron and gamma signals individually or in a combination can be developed. Removal of fuel pins from the assembly will cause the signatures to be visibly perturbed thus enabling the detection of diversion. All of the required signal processing to obtain signatures can be performed on standard laptop computers. Monte Carlo simulation studies and a set of controlled experiments with actual commercial PWR spent fuel assemblies were performed and validated this novel methodology. Based on the simulation studies and benchmarking measurements, the methodology developed promises to be a powerful and practical way to detect partial defects that constitute 10% or more of the total active fuel pins. This far exceeds the detection threshold of 50% missing pins from a spent fuel assembly, a threshold defined by the IAEA Safeguards Criteria. The methodology does not rely on any operator provided data like burnup or cooling time and does not require movement of the fuel assembly from the storage rack in the spent fuel pool. A concept was developed to build a practical field device, Partial Defect Detector (PDET), which will be completely portable and will use standard radiation measuring devices already in use at the IAEA. The use of the device will not require any information provided by the operator or any prior knowledge of the spent fuel assembly. The device can also be operated without any movement of the spent fuel from its storage position. Based on parametric studies conducted via computer simulation, the device should be able to detect diversion of as low as ten percent of the missing or replaced fuel from an assembly regardless of the location of the missing fuel within the assembly, of the cooling time, initial fuel enrichment or burnup levels. Conditions in the spent fuel pool such as clarity of the water or boron content are also not issues for this device. The shape of the base signature is principally dependent on the layout of the guide tubes in the various types of PWR fuel assemblies and perturbations in the form of replaced fuel pins will distort this signature. These features of PDET are all unique and overcome limitation and disadvantages presented by currently used devices such as the Fork detector or the Cerenkov Viewing Device. Thus, this device when developed and tested could fill an important need in the safeguards area for partial defect detection, a technology that the IAEA has been seeking for the past few decades.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

Spent Nuclear Fuel Exploratory Roadmaps - 20054

The U.S. Department of Energy manages nearly 2,500 metric tons of heavy metal (MTHM) of spent nuclear fuel (SNF) resulting from several decades of research, testing, and production reactors [DOE 1995]. This SNF is managed at the DOE Hanford Site in Washington State (Hanford), Idaho National Laboratory (INL), and Savannah River Site in South Carolina (SRS). From 1995 to 2004, the Department of Energy (DOE) made several key programmatic decisions, supported by appropriate documentation in accordance with the National Environmental Policy Act (NEPA) for the management of SNF [DOE 1995]. These decisions have provided an overarching framework for SNF management, as well as site-specific and SNF-related management decisions for the past two decades. In the years since these decisions were made, with the notable exception of the successful drying and packaging of the production reactor fuel at Hanford, a majority of the decisions have been largely unimplemented. Also, since these decisions were made, a number of changes that bear on considerations relative to the path forward have occurred. A SNF Exploratory Road map activity, identified reasonable alternate pathways for DoE's inventory of SNF. Three fundamental pathways were identified in this activity for the long-term management and disposition of DOE SNF: Direct Disposal Pathway, Existing Processing Pathway and Alternate Processing Pathway. Further actions would be required (e.g., evaluation of NEPA analysis, technology maturity evaluations, refinement of cost and risks, benefits and advantages relative to other alternate paths) to define and inform many key decisions that will result in the selection of the disposition pathways that are most beneficial to the US Government in dispositioning DoE's SNF inventory. DOE is currently managing all SNF safely; however, the age of DOE-owned SNF and facilities for storing and processing SNF, coupled with the uncertainty of the storage duration, necessitates decisions and actions to ensure that the infrastructure will be in place to ensure continued safe and effective long-term management and eventual disposal. The identification of reasonable alternate pathways took these considerations into account in an effort to proactively manage conditions that could challenge the safety of storing and managing DOE SNF over the time periods now contemplated and also to ensure that flexibility is preserved to ensure that the DOE SNF remains compatible with final disposition pathways when they become available. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Fuel Accident Condition Simulator (FACS) Furnace for Post-Irradiation Heating Tests of VHTR Fuel Compacts

Abstract –Fuel irradiation testing and post-irradiation examination are currently in progress as part of the Next Generation Nuclear Plant Fuels Development and Qualification Program. The PIE campaign will include extensive accident testing of irradiated very high temperature reactor fuel compacts to verify fission product retention characteristics at high temperatures. This work will be carried out at both the Idaho National Laboratory (INL) and the Oak Ridge National Laboratory, beginning with accident tests on irradiated fuel from the AGR-1 experiment in 2010. A new furnace system has been designed, built, and tested at INL to perform high temperature accident tests. The Fuel Accident Condition Simulator furnace system is designed to heat fuel specimens at temperatures up to 2000°C in helium while monitoring the release of volatile fission metals (e.g. Cs, Ag, Sr, Eu, and I) and fission gases (Kr, Xe). Fission gases released from the fuel to the sweep gas are monitored in real time using dual cryogenic traps fitted with high purity germanium detectors. Condensable fission products are collected on a plate attached to a water-cooled cold finger that can be exchanged periodically without interrupting the test. Analysis of fission products on the condensation plates involves dry gamma counting followed by chemical analysis of selected isotopes. This paper will describe design and operational details of the Fuel Accident Condition Simulator (FACS) furnace system, as well as preliminary system calibration results.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Brazing Refractory Metals Used In High-Temperature Nuclear Instrumentation

As part of the U. S. Department of Energy (DOE) sponsored Next Generation Nuclear Project (NGNP) currently ongoing at Idaho National Laboratory (INL), the irradiation performance of candidate high-temperature gas reactor fuels and materials is being evaluated at INL’s Advanced Test Reactor (ATR). The design of the first Advanced Gas Reactor (AGR 1) experiment, currently being irradiated in the ATR, required development of special techniques for brazing niobium and molybdenum. Brazing is one technique used to join refractory metals to each other and to stainless steel alloys. Although brazing processes are well established, it is difficult to braze niobium, molybdenum, and most other refractory metals because they quickly develop adherent oxides when exposed to room-temperature air. Specialized techniques and methods were developed by INL to overcome these obstacles. This paper describes the techniques developed for removing these oxides, as well as the ASME Section IX-qualified braze procedures that were developed as part of the AGR-1 project. All brazes were made using an induction coil with an inert or reducing atmosphere at low pressure. Other parameters, such as filler metals, fluxes used, and general setup procedures, are also discussed.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗

Thermal Model of the AGR-5/6/7 Experiment

Several fuel and material irradiation experiments have been planned for the U.S. Department of Energy Advanced Gas Reactor Fuel Development and Qualification Program, which supports the development and qualification of tristructural isotropic (TRISO) coated particle fuel for use in high-temperature gas-cooled reactors. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development of fuel performance models and codes, and provide irradiated fuel and materials for post-irradiation examination and safety testing. Originally planned and named as separate fuel experiments, but subsequently combined into a single test train, AGR-5/6/7 will test low-enriched uranium oxycarbide (UCO – a heterogeneous mixture of uranium oxide and uranium carbide) TRISO fuel. The AGR-5/6 portion of the experiment will provide data to support qualification of the selected reference fuel design, while the AGR-7 portion will serve as a margin test, irradiating the fuel beyond normal operating conditions. A thermal finite element model has been created for the five capsules comprising the AGR-5/6/7 experiment. Heat rates from a physics analysis are imported into the model along with fast neutron fluence. Graphite shrinkage due to the fast neutron fluence is incorporated into the model. Gas gaps change as a function of fast neutron fluence. Radiation heat transfer is a major contributor in this model. This is a large model with more than 1 million finite element brick elements. More than 150 different parts are modeled in the finite element model and communicate with each other from a heat transfer sense. More than 50 thermocouples are used in the experiment and are compared to actual measurements. The experiment is composed of five separate stainless steel capsules all welded together. Each capsule has its own Helium/.Neon gas mixture to help control the temperature of the capsule.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Thermal Model Heat Rate Predictions of the AGR-5/6/7 Experiment

Several fuel and material irradiation experiments have been planned for the U.S. Department of Energy Advanced Gas Reactor Fuel Development and Qualification Program, which supports the development and qualification of tristructural isotropic (TRISO) coated particle fuel for use in high-temperature gas-cooled reactors. The goals of these experiments are to provide irradiation performance data to support fuel process development, qualify fuel for normal operating conditions, support development of fuel performance models and codes, and provide irradiated fuel and materials for post-irradiation examination and safety testing. Originally planned and named as separate fuel experiments, but subsequently combined into a single test train. AGR-5/6/7 will test low-enriched uranium oxycarbide (UCO – a heterogeneous mixture of uranium oxide and uranium carbide) TRISO fuel. The AGR-5/6 portion of the experiment will provide data to support qualification of the selected reference fuel design, while the AGR-7 portion will serve as a margin test, irradiating the fuel beyond normal operating conditions. During irradiation, the temperature in each capsule is controlled by varying the helium / neon gas mixture flowing through the capsule until the desired thermocouple temperature is reached. Further adjustments can be made by changing the lobe power and the neutron filter. Three neutron filters are available to use as the experiment burns up the fissionable fuel. A thermal finite element model has been created for the five capsules comprising the AGR-5/6/7 experiment. Heat rates from a physics analysis are imported into the model along with fast neutron fluence. Graphite shrinkage due to the fast neutron fluence is incorporated into the model. Gas gaps change as a function of fast neutron fluence. Radiation heat transfer is a major contributor in this model. This is a large model with more than 1 million finite element brick elements. More than 150 different parts are modeled in the finite element model and communicate with each other from a heat transfer sense. More than 50 thermocouples are used in the experiment and are compared to actual measurements. The experiment is composed of five separate stainless steel capsules all welded together. This paper presents a method used to predict the gas mixture in the event that all of the thermocouples fail in a particular capsule. Curve fitting of heat rates from previous cycles and projecting them into the future is the basis of the method.

36 MATERIALS SCIENCE↗

Kriging-Based Inverse Uncertainty Quantification of BISON Fission Gas Release Model

Nuclear reactor fuel performance analysis studies the thermo-mechanical behavior of fuel rods and verify their compliance with safety criteria under both normal operation and accidental conditions. One of the major concerns in fuel performance analysis is the behavior of the fission gases xenon and krypton in uranium dioxide fuel, which significantly affect the thermo-mechanical performance of the nuclear fuel rods employed in current LWRs. Previously, the modeling of fission gas release (FGR) in nuclear fuel performance codes have been relying on empirical models which are not applicable beyond their range of calibration. Recently a more efficient and flexible physics-based FGR and swelling model that can describe a wider range of reactor operation conditions have been implemented in fuel performance code BISON. In this work, we performed Bayesian calibration to inversely quantify the uncertainties associated with the 5 tuning parameters in BISON FGR model, based on the time-dependent FGR measurement data from Riso-AN3 benchmark. It takes around 1 hour and 40 minutes for BISON to simulate the Riso-AN3 benchmark with a moderate mesh size using 32 processors. As hundreds of thousands of BISON simulations are needed during Markov Chain Monte Carlo (MCMC) sampling, running BISON directly is not a viable solution. Therefore we propose to use Kriging-based metamodels to replace BISON during MCMC sampling. Surrogate model is an approximation of the input/output relation of a computer code/model. It is also called metamodel, response surface, emulator. Surrogate models usually take much less computational time than the original model (like BISON) while maintaining the input/output relation of the original model to a desirable accuracy. Constructing the metamodels normally requires small number of executions of the original model. Once validated, metamodels can be used to perform uncertainty and sensitivity analysis, Bayesian calibration, optimization, etc.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗