Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “RADIO ANTENNA”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS1992

The Galileo plasma wave investigation

The purpose of the Galileo plasma wave investigation is to study plasma waves and radio emissions in the magnetosphere of Jupiter. The plasma wave instrument uses an electric dipole antenna to detect electric fields, and two search coil magnetic antennas to detect magnetic fields. The frequency range covered is 5 Hz to 5.6 MHz for electric fields and 5 Hz to 160 kHz for magnetic fields. Low time-resolution survey spectrums are provided by three on-board spectrum analyzers. In the normal mode of operation the frequency resolution is about 10 percent, and the time resolution for a complete set of electric and magnetic field measurements is 37.33 s. High time-resolution spectrums are provided by a wideband receiver. The wideband receiver provides waveform measurements over bandwidths of 1, 10, and 80 kHz. Compared to previous measurements at Jupiter this instrument has several new capabilities. These new capabilities include (1) both electric and magnetic field measurements to distinguish electrostatic and electromagnetic waves, (2) direction finding measurements to determine source locations, and (3) increased bandwidth for the wideband measurements.

Gurnett, D. A.↗
NASA NTRS1992

Integrated solar power satellites: An approach to low-mass space power

Previous concepts for solar power satellites have used conventional-technology photovoltaic arrays, feeding a power collection and transmission system connected to microwave tubes for direct current to radio frequency DC to RF conversion, which in turn are coupled to a phased array antenna. This paper proposes using thin-film photovoltaics with an integrated solid-state phased-array to design an ultra-lightweight solar power satellite. The status of the enabling technologies, conceptual designs, possible applications, and development steps are discussed. It is found that as these technologies evolve, their use in this design results in a potential reduction in weight by a factor of ten to a hundred over conventional concepts for solar power satellites, and increases the utility by allowing service to smaller receivers at multiple receiving sites.

Landis, Geoffrey A.↗
NASA NTRS2012

670-GHz Down- and Up-Converting HEMT-Based Mixers

A large category of scientific investigation takes advantage of the interactions of signals in the frequency range from 300 to 1,000 GHz and higher. This includes astronomy and atmospheric science, where spectral observations in this frequency range give information about molecular abundances, pressures, and temperatures of small-sized molecules such as water. Additionally, there is a minimum in the atmospheric absorption at around 670 GHz that makes this frequency useful for terrestrial imaging, radar, and possibly communications purposes. This is because 670 GHz is a good compromise for imaging and radar applications between spatial resolution (for a given antenna size) that favors higher frequencies, and atmospheric losses that favor lower frequencies. A similar trade-off applies to communications link budgets: higher frequencies allow smaller antennas, but incur a higher loss. All of these applications usually require converting the RF (radio frequency) signal at 670 GHz to a lower IF (intermediate frequency) for processing. Further, transmitting for communication and radar generally requires up-conversion from IF to the RF. The current state-of-the-art device for performing the frequency conversion is based on Schottky diode mixers for both up and down conversion in this frequency range for room-temperature operation. Devices that can operate at room temperature are generally required for terrestrial, military, and planetary applications that cannot tolerate the mass, bulk, and power consumption of cryogenic cooling. The technology has recently advanced to the point that amplifiers in the region up to nearly 1,000 GHz are feasible. Almost all of these have been based on indium phosphide pseudomorphic high-electron mobility transistors (pHEMTs), in the form of monolithic microwave integrated circuits (MMICs). Since the processing of HEMT amplifiers is quite differ en t from that of Schottky diodes, use of Schottky mixers requires separate MMICs for the mixers and amplifiers. Fabrication of all the down-/up-conversion circuitry on single MMICs, using a ll-HEMT circuits, would constitute a major advance in circuit simplicity.

Schlecht, Enrich T.↗
NASA NTRS2013

RF Reference Switch for Spaceflight Radiometer Calibration

The goal of this technology is to provide improved calibration and measurement sensitivity to the Soil Moisture Active Passive Mission (SMAP) radiometer. While RF switches have been used in the past to calibrate microwave radiometers, the switch used on SMAP employs several techniques uniquely tailored to the instrument requirements and passive remote-sensing in general to improve radiometer performance. Measurement error and sensitivity are improved by employing techniques to reduce thermal gradients within the device, reduce insertion loss during antenna observations, increase insertion loss temporal stability, and increase rejection of radar and RFI (radio-frequency interference) signals during calibration. The two legs of the single-pole double-throw reference switch employ three PIN diodes per leg in a parallel-shunt configuration to minimize insertion loss and increase stability while exceeding rejection requirements at 1,413 MHz. The high-speed packaged diodes are selected to minimize junction capacitance and resistance while ensuring the parallel devices have very similar I-V curves. Switch rejection is improved by adding high-impedance quarter-wave tapers before and after the diodes, along with replacing the ground via of one diode per leg with an open circuit stub. Errors due to thermal gradients in the switch are reduced by embedding the 50-ohm reference load within the switch, along with using a 0.25-in. (approximately equal to 0.6-cm) aluminum prebacked substrate. Previous spaceflight microwave radiometers did not embed the reference load and thermocouple directly within the calibration switch. In doing so, the SMAP switch reduces error caused by thermal gradients between the load and switch. Thermal issues are further reduced by moving the custom, highspeed regulated driver circuit to a physically separate PWB (printed wiring board). Regarding RF performance, previous spaceflight reference switches have not employed high-impedance tapers to improve rejection. The use of open-circuit stubs instead of a via to provide an improved RF short is unique to this design. The stubs are easily tunable to provide high rejection at specific frequencies while maintaining very low insertion loss in-band.

Knuble, Joseph↗
NASA NTRS1991

System-Level Integrated Circuit (SLIC) development for phased array antenna applications

A microwave/millimeter wave system-level integrated circuit (SLIC) being developed for use in phased array antenna applications is described. The program goal is to design, fabricate, test, and deliver an advanced integrated circuit that merges radio frequency (RF) monolithic microwave integrated circuit (MMIC) technologies with digital, photonic, and analog circuitry that provide control, support, and interface functions. As a whole, the SLIC will offer improvements in RF device performance, uniformity, and stability while enabling accurate, rapid, repeatable control of the RF signal. Furthermore, the SLIC program addresses issues relating to insertion of solid state devices into antenna systems, such as the reduction in number of bias, control, and signal lines. Program goals, approach, and status are discussed.

Shalkhauser, K. A.↗
NASA NTRS1991

System-level integrated circuit (SLIC) development for phased array antenna applications

A microwave/millimeter wave system-level integrated circuit (SLIC) being developed for use in phased array antenna applications is described. The program goal is to design, fabricate, test, and deliver an advanced integrated circuit that merges radio frequency (RF) monolithic microwave integrated circuit (MMIC) technologies with digital, photonic, and analog circuitry that provide control, support, and interface functions. As a whole, the SLIC will offer improvements in RF device performance, uniformity, and stability while enabling accurate, rapid, repeatable control of the RF signal. Furthermore, the SLIC program addresses issues relating to insertion of solid state devices into antenna systems, such as the reduction in number of bias, control, and signal lines. Program goals, approach, and status are discussed.

Shalkhauser, K. A.↗
NASA NTRS1985

Radio phase characteristics of terrain from multipolarized synthetic aperture radar data

Recent advances in digital data acquisition and signal processing technology permit simultaneous measurement of the complex (amplitude and phase) radar backscatter from several polarization-diverse antennas. While absolute phase mesurements remain to be analyzed in detail. The differential phase of signals polarized parallel and perpendicular to the plane of incidence provide information on the scattering mechanisms that dominate the interaction of the radio waves with the terrain. Analysis of phase backscatter maps from a typical urban area yields a bimodal distribution with the two peaks separated by approximately 180 degrees, highly indicative of a dominant simple geometric one bounce-two bounce mechanism. Some maps of agricultural areas exhibit a similar distribution, however, other agricultural areas yield a distribution that, while still bimodal, consists of two peaks separated by about 110 deg. Still other agricultural areas exhibit a more complex distribution. All of the observed phase shifts appear to be independent of incidence angle from at least 20 deg to 55 deg, therefore the 110 degree shifts are inconsistent with both the geometric model used for the urban area and with common dielectric slab models.

Zebker, H. A.↗
NASA NTRS1977

Millimeter-wave antenna design

Problems and opportunities are discussed for adapting certain design features and construction techniques, developed for producing high accuracy ground based radio dishes, to producing milimeter wave dishes for space use. Specifically considered is a foldable telescope of 24 m aperture and 9.6 m focal length, composed of 37 rigid hexagonal panels, which will fit within the 4.5 m diameter x 18 m long payload limits of space shuttle. As here conceived, the telescope would be a free flyer with its own power and pointing systems. Some of the structural design features and construction procedures are considered.

Leighton, R. B.↗
NASA NTRS1977

Airborne urban/suburban noise measurements at 121.5/243 MHz

An airborne measurement of the terrestrial, radio-frequency (RF) noise environment over U.S. metropolitan urban/suburban areas has been made at the 121.5/243 MHz emergency-distress search and rescue (S&R) communications frequencies. Profile contour plots of antenna-noise temperature for U.S.A. East Coast and mid-west urban/suburban areas is presented for daytime/nighttime observations at 121.5/243 MHz. These plots are helpful for compiling radio-noise environment maps; in turn useful for designing satellite-aided, emergency-distress search and rescue communication systems.

Taylor, R. E.↗
NASA NTRS1997

Trends in Performance and Characteristics of Ultra-Stable Oscillators for Deep Space Radio Science Experiments

Telecommunication systems of spacecraft on deep space missions also function as instruments for Radio Science experiments. Radio scientists utilize the telecommunication links between spacecraft and Earth to examine very small changes in the phase/frequency, amplitude, and/or polarization of radio signals to investigate a host of physical phenomena in the solar system. Several missions augmented the radio communication system with an Ultra-Stable Oscillator (USO) in order to provide a highly stable reference signal for oneway downlink. This configuration is used in order to enable better investigations of the atmospheres of the planets occulting the line-of-sight to the spacecraft; one-way communication was required and the transponders' built-in auxiliary oscillators were neither sufficiently stable nor spectrally pure for the occultation experiments. Since Radio Science instrumentation is distributed between the spacecraft and the ground stations, the Deep Space Network (DSN) is also equipped to function as a world-class instrument for Radio Science research. For a detailed account of Radio Science experiments, methodology, key discoveries, and the DSN's historical contribution to the field, see Asmar and Renzetti (1993). The tools of Radio Science can be and have also been utilized in addressing several mission engineering challenges; e.g., characterization of spacecraft nutation and anomalous motion, antenna calibrations, and communications during surface landing phases. Since the first quartz USO was flown on Voyager, the technology has advanced significantly, affording future missions higher sensitivity in reconstructing the temperature pressure profiles of the atmospheres under study as well as other physical phenomena of interest to Radio Science. This paper surveys the trends in stability and spectral purity performance, design characteristics including size and mass, as well as cost and history of these clocks in space.

Asmar, Sami↗
NASA NTRS1977

A refracting radio telescope

Observations of extraterrestrial radio sources at the lower end of the radio frequency spectrum are limited by reflection of waves from the topside ionosphere and by the large size of antenna apertures necessary for the realization of narrow beamwidths. The use of the ionosphere as a lens is considered. The lens is formed by the release of chemicals such as H2 and H2O at the F2-layer peak. These chemicals promote dissociative recombination of O(+) in the ionosphere resulting in a local reduction in plasma density. Gradients in electron density in the vicinity of the gas release tend to focus rays propagating through the depleted region. Preliminary calculations indicate that a lens capable of focusing cosmic radio waves in the 1 to 10 MHz frequency range may be produced by the release of 100 kg of H2 at the peak of the nighttime F layer. The beamwidth of a refracting radio telescope using this lens may be less than 1/5 degree.

Bernhardt, P.↗
NASA NTRS1985

Electro-science Requirements for Shuttle-attached Antenna Flight Experiments

The activities of an in-house electro-science task group organized to conduct studies of shuttle-attached flight experiments using the 15-meter hoop-column antennas as a research tool for developing both improved sensor technology and LSA technology are described. Some experiments could provide significant amounts of scientific data such as radio star mapping and definition of ocean current eddies over limited geographic regions. The experiments originate from the microwave remote sensing community and other areas which require the inherently higher resolution and boresite gain of large space antennas. Technology experiments are also being studied which would use the 15-meter antenna experiments as a stepping stone to 50 to 100 meter class reflector technology in the future. An antenna technology experiment using the 15-meter antenna in a shuttle-attached mission is discussed. Electromagnetic modeling is correct for each major subsystem and also to verify the interrelations of the subsystems.

Grantham, W. L.↗
NASA NTRS1974

Venus - Mass, gravity field, atmosphere, and ionosphere as measured by the Mariner 10 dual-frequency radio system

The unique properties of the Mariner 10 radio system, and the preliminary scientific results obtained from the analysis of the radio signals are described. In the normal two-way communication mode, a command- and range-modulated 2115-MHz signal is transmitted to the spacecraft for reception on its omnidirectional antenna. As implemented for Mariner 10, the dual-frequency system has proven fully capable of performing interplanetary columnar electron content measurements while achieving the prime goals of the celestial mechanics and radio science team. The determination of the mass and gravitational potential of Venus is one of the major objectives of the radio science experiments. Information on Venus's atmosphere was deduced from analysis of the radio signals during occultation. Open-loop receiver differential Doppler data were used to measure the nightside and dayside ionospheres of Venus.

Howard, H. T.↗
NASA NTRS1997

A Tour of the Goldstone-Apple Valley Radio Telescope

Goldstone-Apple Valley Radio Telescope (GAVRT) is located in a remote area of the Mojave Desert, 40 miles north of Barstow, California. The antenna, identified as DSS-12, is a 34-meter diameter dish, 11 times the diameter of a ten foot microwave dish used for satellite television. DSS-12 has been used by NASA to communicate with robotic space probes for more than thirty years.

Goldstone-Apple Valley Radio Telescope↗
DOE OSTI2026

Simulations of ICRF Heating for SPARC during First Campaign and Primary Reference-Like Discharge using the Stix Code

High magnetic field tokamaks, like SPARC, rely on ion cyclotron radio frequency heating (ICRF) to reach fusion relevant temperatures. The SPARC tokamak will have 14 ICRF antennas in 7 toroidal locations delivering > 20 MW of power to the plasma. New capabilities with the full wave cold plasma solver, Stix, now allow for resolving the wave-particle resonances using lower order thermal corrections to capture core absorption of Landau damping and ion resonances in devices like SPARC. Favorable comparisons to the TORIC codes give confidence in the single pass absorption of this model to accurately capture the strength of edge interactions of the RF. Using this new dielectric formulation in the Stix code, simulations of the 2D poloidal cross section of SPARC are completed for the first campaign and primary reference-like discharges (PRD-like). A scan of the minority ion concentrations of helium-3 is performed and shows the expected behavior that as the helium-3 decreases the amount of single pass absorption also decreases which is seen in both scenarios. Additionally, both scenarios show only slight differences in single-pass absorption for the range of 3% to 5% helium-3 allowing for more flexibility in experiments. This study also highlights the differences between the first campaign and PRD-like with the first campaign discharges showing much more multi-pass absorption and an effect of confining the wave to a smaller portion of the cross-section due to the fast wave cut-off. This latter result suggests that far-field sheath rectification at the high-field side would be minimal for the first campaign scenario.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗
DOE OSTI2024

Characterization of SOL profiles and turbulence in ICRF-heated plasmas in EAST

Scrape-off layer (SOL) profiles and turbulence in ion cyclotron range of frequency (ICRF)-heated plasmas are investigated by the reciprocating probe diagnostic system (FRPs) and gas puff imaging (GPI) diagnostic in EAST. A radio-frequency (RF) sheath potential reaching up to 100 V is identified proximate to the ICRF antennas. Notably, the amplitude of this RF sheath potential escalates in response to rising ICRF power and inversely with plasma density. When a RF sheath is present in the far SOL, a pronounced density ‘shoulder’ forms in front of the ICRF antennas, while the ‘shoulder’ fade away as the antenna and associated RF sheath shift outwards. A strong E r shear is revealed by measurements from both FRPs and GPI. Analysis of the poloidal wave number-frequency spectrum reveals suppression of high-frequency turbulence in the far SOL due to the RF sheath. This effect is manifested in the reduced autocorrelation time τ c and reduced average blob size δ blob of the SOL plasma. Intriguingly, the poloidal propagation direction of the low-frequency turbulence reverses from the electron to the ion diamagnetic drift direction at the RF sheath location. A surge of tungsten impurity is potentially attributed to the heightened interaction between the SOL plasmas and the wall material. Shifting the ICRF antennas outward, to alleviate heat spots, results in the relocation of the RF sheath to the shaded region of the main limiter. This shift amplifies the radial velocity of blobs in the far SOL and concurrently diminishes the SOL density when compared to conditions without ICRF injection. The properties of ion saturation current fluctuations are consistent with the stochastic model predictions.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗