SEARCH · Engineering Papers

Results for “Phase change”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1992

High temperature conductivity of potassium-beta(double prime)-alumina

Potassium beta(double prime)-alumina (BDPA) single crystals have been reported by several groups to leave higher ionic conductivity than sodium BDPA crystals at room temperature, and similar conductivities are obtained at temperatures up to 600-700 K. Potassium BDPA ceramics have been reported to have significantly poorer conductivities than those of sodium BDPA ceramics, but conductivity measurements at temperatures above 625 K have not been reported. In this study, K(+)-BDPA ceramics were prepared from Na(+)-BDPA ceramic using a modified version of the exchange reaction with KCl vapor reported by Crosbie and Tennenhouse (1982), and the conductivity has been measured in K vapor at temperatures up to 1223 K, using the method of Cole et al. (1979). The results indicate reasonable agreement with earlier data on K(+)-BDPA ceramic measured in a liquid K cell, but show that the K(+)-BDPA ceramic's conductivity approaches that of Na(+)-BDPA ceramic at higher temperatures, being within a factor of four at 700 K and 60 percent of the conductivity of Na(+)-BDPA at T over 1000 K. Both four-probe dc conductivity and four probe ac impedance measurements were used to characterize the conductivity. A rather abrupt change in the grain boundary resistance suggesting a possible phase change in the intergranular material, potassium aluminate, is seen in the ac impedance behavior.

Williams, R. M.↗

NASA NTRS1994

A new approach to estimating rainwater content by radar using propagation differential phase shift

As microwaves propagate through rain, the rate of phase change with increasing distance is different depending upon whether the transmissions are polarized horizontally or vertically. This rate of change is the so-called specific propagation differential phase shift phi(sub DP). This paper demonstrates that at several frequencies and over a wide domain the ratio of phi(sub DP) to the rainwater content W is nearly linearly related to D(sub m), the mass-weighted mean drop size. An investigation of errors indicates that this new approach is likely to yield more accurate estimates of W than the other classical reflectivity factor Z, attenuation, or polarization techniques. The most accurate estimates of W are most likely at the highest frequency considered, 13.80 GHz. In lieu of such high-frequency measurements, these somewhat esoteric results are made more concrete through an analysis of 3-GHz radar measurements collected during the Convection and Precipitation Experiment in a tropical rainstorm in Florida. Among the principal advantages of using phi(sub DP) to measure rain are that an absolute calibration of the radar is no longer required and the estimates are decoupled from measurements of the radar reflectivity factor. Consequently, temporal and spatial structures of rain estimates do not simply mimic those of the reflectivity factor, as happens for classical estimation techniques using Z.

Jameson, A. R.↗

NASA NTRS2017

Gravity Effects in Microgap Flow Boiling

Increasing integration density of electronic components has exacerbated the thermal management challenges facing electronic system developers. The high power, heat flux, and volumetric heat generation of emerging devices are driving the transition from remote cooling, which relies on conduction and spreading, to embedded cooling, which facilitates direct contact between the heat-generating device and coolant flow. Microgap coolers employ the forced flow of dielectric fluids undergoing phase change in a heated channel between devices. While two phase microcoolers are used routinely in ground-based systems, the lack of acceptable models and correlations for microgravity operation has limited their use for spacecraft thermal management. Previous research has revealed that gravitational acceleration plays a diminishing role as the channel diameter shrinks, but there is considerable variation among the proposed gravity-insensitive channel dimensions and minimal research on rectangular ducts. Reliable criteria for achieving gravity-insensitive flow boiling performance would enable spaceflight systems to exploit this powerful thermal management technique and reduce development time and costs through reliance on ground-based testing. In the present effort, the authors have studied the effect of evaporator orientation on flow boiling performance of HFE7100 in a 218 m tall by 13.0 mm wide microgap cooler. Similar heat transfer coefficients and critical heat flux were achieved across five evaporator orientations, indicating that the effect of gravity was negligible.

microscale↗

NASA NTRS2017

Gravity Effects in Microgap Flow Boiling

microscale↗

NASA NTRS2019

Tunable mid-wave infrared spectral filters based on GexSbyTez for multispectral imaging

The mid-wave infrared (MWIR) spectrum contains a wealth of invaluable information including the spectral ‘fingerprint’ of many chemical species and has applications in remote sensing and astronomical imaging. Traditionally, filtering for the MWIR is achieved by means of passive multilayer interference (dichroic) filters, Fabry-Perot-based micro-electro-mechanical system (MEMS) filters, liquid crystal tunable filters, and focal plane array (FPA) filters. For accurate multispectral imaging applications, these approaches suffer from various limitations such as: having moving parts; exhibiting slow response times, and; having limited spectral bandwidth / resolution. Recently, there has been significant interest toward ‘active’ spectral imaging technologies, whereby the ability to provide electrically tunable narrowband filtering—spanning the entire MWIR—is highly desirable. In this work we introduce a new spectral imaging technology, namely actively tunable optical transmission filters using the phase-change material (PCM) GexSbyTez (GST). The GST exhibits a large, reversible change in its refractive index across the MWIR upon a phase transition (from amorphous to crystalline). This refractive index modulation governs the filter’s optical characteristics. Through an optical stimulus or applied voltage—which changes the GST state from amorphous to crystalline—one can actively tune the filter with MHz speed. We incorporate GST into optimized guided mode resonance (GMR) and plasmonic nanohole array (PNA) device architectures, enabling <10nm spectral resolution and tunable operation across 3~5µm. Our proposed PCM-MWIR filter will be able to extract the maximum amount of ‘useful’ information within the atmosphere for remote Earth sensing measurements at operational speeds orders of magnitude faster than current airborne-based sensors. Moreover, it may enable affordable SmallSat-based MWIR instrumentation which is complimentary to other observation systems. The MISSE (Materials International Space Station Experiment-Flight Facility) experiment has been proposed as a testbed for a PCM-based tunable MWIR filter module to allow exposure of the module to the low Earth orbit space environment. This will provide valuable data regarding the robustness of the filter to withstand the radiation and atomic oxygen environment and allow assessment of the technology for use in space applications.

Kim, Hyun Jung↗

NASA NTRS1992

Frequency, phase, and amplitude changes of the hydrogen maser oscillation

The frequency, the phase, and the amplitude changes of the hydrogen maser oscillation, which are induced by the modulation of the cavity resonant frequency, are considered. The results obtained apply specifically to one of the H-maser cavity autotuning methods which is actually implemented, namely the cavity frequency-switching method. The frequency, the phase, and the amplitude changes are analyzed theoretically. The phase and the amplitude variations are measured experimentally. It is shown, in particular, that the phase of oscillation is subjected to abrupt jumps at the times of the cavity frequency switching, whose magnitude is specified. The results given can be used for the design of a phase-locked loop (PLL) aimed at minimizing the transfer of the phase modulation to the slaved VCXO.

Audoin, Claude↗

DOE OSTI2021

Multi-fidelity electrochemical modeling of thermally activated battery cells

Thermally activated batteries undergo a series of coupled physical changes during activation that influence battery performance. These processes include energetic material burning, heat transfer, electrolyte phase change, capillary-driven two-phase porous flow, ion transport, electrochemical reactions, and electrical transport. Several of these processes are strongly coupled and have a significant effect on battery performance, but others have minimal impact or may be suitably represented by reduced-order models. Additionally, assessing the relative importance of these phenomena must be based on comparisons to a high-fidelity model including all known processes. In this work, we first present and demonstrate a high-fidelity, multi-physics model of electrochemical performance. This novel multi-physics model enables predictions of how competing physical processes affect battery performance and provides unique insights into the difficult-to-measure processes that happen during battery activation. We introduce four categories of model fidelity that include different physical simplifications, assumptions, and reduced-order models to decouple or remove costly elements of the simulation. Using this approach, we show an order-of-magnitude reduction in computational cost while preserving all design-relevant quantities of interest within 5 percent. The validity of this approach and these model reductions is demonstrated by comparison between results from the full fidelity model and the different reduced models.

25 ENERGY STORAGE↗

DOE OSTI2022

Stable salt hydrate-based thermal energy storage materials

Heating and cooling systems in building infrastructure utilize conventional materials that account for a considerable amount of energy usage and waste. Phase change material (PCM) is considered a promising candidate for thermal energy storage that can improve energy efficiency in building systems. In this work, a novel salt hydrate-based PCM composite with high energy storage capacity, relatively higher thermal conductivity, and excellent thermal cycling stability was designed and developed. The thermal cycling stability of the PCM composite was enhanced by using dextran sulfate sodium (DSS) salt as a polyelectrolyte additive, which significantly reduced the phase segregation of salt hydrate. The energy storage capacity and the thermal conductivity of the composite were enhanced by the addition of various graphitic materials along with Borax nucleator. A significant increase in thermal cycling stability was observed for the DSS-modified composite, with over 100 thermal cycles without degradation. The final PCM composite exhibited as much as 290% increase in energy storage capacity relative to the pure salt hydrate, and approximately 20% increase in thermal conductivity. In addition, the PCM composite developed can be produced at larger scale, and can potentially change the future of heating/cooling system in building infrastructure.

42 ENGINEERING↗

NASA NTRS1988

Theory of anisotropic refractive scintillation - Application to stellar occultations by Neptune

A theory of refractive scintillation due to a thin phase-changing screen with an anisotropic power-law spectrum of phase fluctuations is presented. Scintillation theory for an isotropic medium is discussed, and anisotropy of the mean density and anisotropy in the scattering are discussed. The theory of refractive scintillation in an anisotropic medium is developed, deriving a general expression for the cross-correlation of flux variations at two points on the 'observer screen'. From this, estimates of the coherence lengths and amplitudes of flux variations are obtained for important parameter regimes. The application of the theory to the analysis of two occultations by Neptune is addressed. The projected dimensions of the occulting stars, a normalization constant to describe the phase fluctuations, and an anisotropy parameter are determined, and the theory is shown to agree well with observation. The significance of the theory for understanding of the physics of Neptune's atmosphere is discussed.

Narayan, Ramesh↗

NASA NTRS1994

Gas kinematics and ionization along the extended sight line to HD 116852

We present Goddard High-Resolution Spectrograph intermediate observations of the interstellar medium toward HD 116852, a low halo star at a distance of 4.8 kpc (z = -1.3 kpc) in the direction l = 304. deg 9, b = 16.deg 1. The small science aperture observations have signal-to-noise ratios ranging from 30 to 90 and resolutions of 11 to 18 km/s (FWHM). We confirm the optical MK classification of this star through an analysis of its ultraviolet photosperic and stellar wind profiles. We detect interstellar lines of Al III, Si IV, C IV, and N V together with lines of C I, C I*, C I**, Si II, Ge II, P II, and Ni II. We convert the Mg II, P II, S II, Al III, Si IV, C IV, and N V profiles into measure of apparent column density as a function of LSR velocity. Gas scale height, velocity dispersion, and differential Galactic rotation effects govern the profile shapes. A simple computer model of the expected sight line column density profiles for the low and high ion species indicates that the gas velocity dispersions and scale heights increase as the ionization level of the gas increases. We find scale heigts H greater than or = 1 kpc for the high ions, which are comparable to the z-distance of the star, whereas we find H approximatley = 0.6 to 0.7 kpc for A1 III and H approximatley 0.1 kpc for P II and Ge II. An enhancement in the Al II profile near -15 km/s accounts for approximately 25% of the A1 III column along the sight line and probably arises within gas located approximately 500 pc below the Sagittarius-Carina spiral arm link. Portions of the broad underlying A1 III distribution are associated with the higher ionization lines, perhaps in conductive interfaces. The presence of N V and the column density ratios of Si IV, C IV, and N V favor the interpretation that much of the high ion absorption is produced by collisional ionization in gas with T = 1-3 x 10(exp 5) K. An enhancement near -35 km/s in both the Si IV and C IV profiles may be due to an outflow from the Norma spiral arm at a z-distance of about -1 kpc. The smooth decrease of the N(C IV)/N(Si IV) ratio at negative velocities may be due to an ISM ionization structure for hot gas that changes distance from the Galactic plane or to a two phase gas distribution in which the relative contribution from each phase changes with distance from the Galactic plane.

Sembach, Kenneth R.↗

NASA NTRS1995

Optical diagnostics of solution crystal growth

Solution crystal growth monitoring of LAP/TGS crystals by various optical diagnostics systems, such as conventional and Mach-Zehnder (M-Z) interferometers, optical heterodyne technique, and ellipsometry, is under development. The study of the dynamics of the crystal growth process requires a detailed knowledge of crystal growth rate and the concentration gradient near growing crystals in aqueous solution. Crystal growth rate can be measured using conventional interferometry. Laser beam reflections from the crystal front as well as the back surface interfere with each other, and the fringe shift due to the growing crystal yields information about the growth rate. Our preliminary results indicate a growth rate of 6 A/sec for LAP crystals grown from solution. Single wavelength M-Z interferometry is in use to calculate the concentration gradient near the crystal. Preliminary investigation is in progress using an M-Z interferometer with 2 cm beam diameter to cover the front region of the growing crystal. In the optical heterodyne technique, phase difference between two rf signals (250 KHZ) is measured of which one is a reference signal, and the other growth signal, whose phase changes due to a change in path length as the material grows. From the phase difference the growth rate can also be calculated. Our preliminary results indicate a growth rate of 1.5 A/sec. the seed and solution temperatures were 26.46 C and 27.92 C respectively, and the solution was saturated at 29.0 C. an ellipsometer to measure the growth rate and interface layer is on order from JOBIN YVON, France. All these systems are arranged in such a manner that measurements can be made either sequentially or simultaneously. These techniques will be adapted for flight experiment.

Kim, Yongkee↗

DOE OSTI2021

Laboratory Evaluation to Increase Effectiveness of Field-Scale Soil Flushing in the Hanford 100 Areas

This laboratory study was initiated to develop an improved technical understanding of the key controlling geochemical and physical processes of mobilizing residual Cr(VI) in Hanford sediments to provide increased effectiveness in soil flushing activities planned for Hanford 100 Areas. This was accomplished by (1) quantifying Cr mass, release rate, and surface phase changes as Cr is leached from different Hanford sediments; (2) maximizing Cr leaching during soil flushing by evaluating different leach solutions and leach strategies; and (3) minimizing leaching of remaining residual Cr after soil flushing ends. To quantify geochemical controls on Cr leaching from sediments, sequential liquid extractions were used to identify aqueous, adsorbed, and solid Cr surface phases (precipitates or Cr incorporated into other phases) before and after water-saturated and unsaturated leach experiments with pH 8 artificial groundwater and with other amendment solutions. Changes in the Cr release rate from sediments were also correlated to changes in Cr surface phases. During unsaturated infiltration, water advection occurs primarily through larger pores, with less movement through smaller grain layers leading to a slower release of Cr trapped in smaller pores next to smaller grains. To quantify these physical controls on Cr leaching from sediments, 10 ft high 1-D infiltration experiments were conducted at differing leach solution application rates, and Cr leaching during application and subsequent residual water flow was quantified. Qualitative 2-D experiments were also conducted to evaluate surfactant addition to increase flow in low-permeability zones. Cr-contaminated Hanford sediments from the 100-H, 100-K, 100-D, and 200 East Areas exhibited a wide variety of leach behavior from rapid release of a small amount of Cr to fast (i.e., minutes) and slow (i.e., hours or more) release of high Cr. Sediments with low labile Cr (< 0.2 µg/g) exhibited fast Cr release but less overall release, and most (>95%) leached from the sediments within a few pore volumes in water-saturated columns. With nearly no sorption of chromate, aqueous and sorbed Cr (as chromate) were released quickly from sediment within the first few pore volumes, resulting in high leach concentrations, fast initial Cr release rates, and changes in pre- and post-leach extractions. In contrast, sediments with high labile Cr (0.2 to 20 µg/g) exhibited a combination of fast and slow Cr release due to multiple Cr surface phases contributing to Cr release from the sediment at different rates with greater overall release. This resulted in elevated Cr effluent concentrations even after dozens of pore volumes were leached. In addition, the Cr release rate decreased with increasing time during leaching. A decrease in labile Cr (aqueous Cr, adsorbed Cr, pH 5 acetate dissolved precipitates) in post-leach extractions compared to pre-leach extractions showed initial aqueous and adsorbed Cr release, followed by dissolution of high-solubility precipitates such as CaCrO 4 (if present), then slow dissolution of calcite that may contain some chromate and possibly BaCrO 4 . The labile Cr in all sediments correlated well with the Cr release rate (r 2 = 0.81). Labile Cr also correlated well with the leached mass in water-saturated columns (r 2 = 0.98), and therefore can be used for prediction of potential removal with flushing applications.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

DOE OSTI2022

Encapsulation of hygroscopic liquids via polymer precipitation in non-aqueous emulsions

Here, encapsulation of ionic liquids (ILs) and phase change materials (PCMs) can overcome limitations associated with bulk materials, e.g., slow mass transfer rates, high viscosities, or susceptibility to external environment. Single step soft-templated encapsulation methods commonly use interfacial polymerization for shell formation, with a multifunctional monomer in the continuous phase and another in the discontinuous phase, and thus do not give pristine core material. We posit that polymer precipitation onto emulsion droplets in non-aqueous emulsions could produce a robust shell without contamination of the core, ideal for the encapsulation of water-sensitive or water-miscible materials. Solutions of commodity polymers were added to the continuous phase of non-aqueous Pickering emulsions stabilized by alkylated graphene oxide (GO) nanosheets such that the change in solubility of the polymer led to formation of robust shells and the production of capsules that could be isolated. We demonstrate that a polymer precipitation approach can produce capsules with pristine core of the IL 1-ethyl-3-methylimidazolium hexafluorophosphate [Emim][PF 6 ] or the salt hydrate PCM magnesium nitrate hexahydrate (MNH) and shell of nanosheets and polystyrene, poly(methyl methacrylate), or polyethylene. The capsules are approximately 80 wt% [Emim][PF 6 ] or >90 wt% MNH, and the core can undergo multiple cycles of solidification and melting without leakage or destruction. This novel, single-step methodology provides a distinct advantage to access capsules with pristine core composition and is amenable to different core and shell, paving the way for tailoring capsule composition for desired applications.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Efficient Reformulation of Linear and Nonlinear Solid-Phase Diffusion in Lithium-ion Battery Models using Symmetric Polynomials: Mass Conservation and Computational Efficiency

Lithium-ion batteries are typically modeled using porous electrode theory coupled with various transport and reaction mechanisms, along with suitable discretization or approximations for the solid-phase diffusion equation. The solid-phase diffusion equation represents the main computational burden for typical pseudo-2-dimensional (p2D) models since these equations in the pseudo r -dimension must be solved at each point in the computational grid. This substantially increases the complexity of the model as well as the computational time. Traditional approaches towards simplifying solid-phase diffusion possess certain significant limitations, especially in modeling emerging electrode materials which involve phase changes and variable diffusivities. A computationally efficient representation for solid-phase diffusion is discussed in this paper based on symmetric polynomials using Orthogonal Collocation and Galerkin formulation (weak form). A systematic approach is provided to increase the accuracy of the approximation (p form in finite element methods) to enable efficient simulation with a minimal number of semi-discretized equations, ensuring mass conservation even for non-linear diffusion problems involving variable diffusivities. These methods are then demonstrated by incorporation into the full p2D model, illustrating their advantages in simulating high C-rates and short-time dynamic operation of Lithium-ion batteries.

25 ENERGY STORAGE↗

NASA NTRS1975

Stable group delay cable

It was found that group delay is function of pressure in air dielectric coaxial cable. For example, 600-ft air dielectric cable will change phase 10 deg at 150 MHz when air pressure in cable changes from zero to 20 psi.

Clements, P. A.↗

NASA NTRS1984

Crystallization of the glassy phase of grain boundaries in silicon nitride

Three types of hot-pressed silicon nitride specimens (containing 5wt% Y2O3 and 2wt% Al2O3 additives) which were subjected to different temperature heat treatments were studied by X-ray diffraction, X-ray microanalysis and high resolution electron microscopy. The results indicated that there were phase changes in the grain boundaries after heat treatment and the glassy phase at the grain boundaries was crystallized by heat treatment.

Jefferson, D. A.↗

NASA NTRS1986

Effect of liquid droplets on turbulence in a round gaseous jet

The main objective of this investigation is to develop a two-equation turbulence model for dilute vaporizing sprays or in general for dispersed two-phase flows including the effects of phase changes. The model that accounts for the interaction between the two phases is based on rigorously derived equations for turbulence kinetic energy (K) and its dissipation rate epsilon of the carrier phase using the momentum equation of that phase. Closure is achieved by modeling the turbulent correlations, up to third order, in the equations of the mean motion, concentration of the vapor in the carrier phase, and the kinetic energy of turbulence and its dissipation rate for the carrier phase. The governing equations are presented in both the exact and the modeled formes. The governing equations are solved numerically using a finite-difference procedure to test the presented model for the flow of a turbulent axisymmetric gaseous jet laden with either evaporating liquid droplets or solid particles. The predictions include the distribution of the mean velocity, volume fractions of the different phases, concentration of the evaporated material in the carrier phase, turbulence intensity and shear stress of the carrier phase, droplet diameter distribution, and the jet spreading rate. The predictions are in good agreement with the experimental data.

Mostafa, A. A.↗

NASA NTRS1990

Arcjet load characteristics

Experiments were conducted to define the interface characteristics and constraints of 1 kW class arcjets run on simulated decomposition products of hydrazine and power processors. The impacts of power supply output current ripple on arcjet performance were assessed by variation of the ripple frequency from 100 Hz to 100 kHz with 10 percent peak-to-peak ripple amplitude at 1.2 kW. Ripple had no significant effects on thrust, specific impulse or efficiency. The impact of output ripple on thruster lifetime was not assessed. The static and dynamic impedances of the arcjet were quantified with two thrusters of nearly identical configuration. Superposition of an AC component on the DC arc current was used to characterize the dynamic impedance as a function of flow rate and DC current level. A mathematical model was formulated from these data. Both the static and dynamic impedance magnitude were found to be dependent on mass flow rate. The amplitude of the AC component was found to have little effect on the dynamic impedance. Reducing the DC level from 10 to 8 amps led to a large change in the magnitude of the dynamic impedance with no observable phase change. The impedance data compared favorably between the two thrusters.

Hamley, John A.↗