Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “O”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

A Comparison of CdS and Zn(O,S) Buffer Layers in (Ag,Cu)(In,Ga)Se2 Solar Cells

Cu(In,Ga)Se 2 -based solar cells typically use a C dS buffer layer, even though its relatively low bandgap causes parasitic absorption. While alternatives to CdS have been explored in other studies, limited results have been shown for Ag-alloyed CIGS (ACIGS). In this study, ACIGS solar cells with both CdS and Zn(O,S) buffer layers were fabricated and compared for solar cell performance. The Zn(O,S) buffer slightly improved J sc through reduced absorption, although surface optimization is necessary. The Zn(O,S) ACIGS also had improved FF through reduced series resistance and ideality factor, which could be improved further through optimization. However, the Voc in the Zn(O,S) samples was reduced, likely due to increased bulk and front interface recombination. This study shows the promise of Zn(O,S) as a buffer layer in ACIGS solar cells and suggests pathways for further improvement.

absorption↗
DOE OSTI2022

Enhanced Surface Passivation by Atomic Layer Deposited Al 2 O 3 for Ultraviolet Sensitive Silicon Photomultipliers

Here, we describe a superior passivation of p-type (p + ) Si surface by Al 2 O 3 thin film that is synthesized by plasma-assisted atomic layer deposition for ultraviolet sensitive silicon photomultipliers (SiPM), compared to conventional SiO 2 and SiN x passivation schemes. The superiority of Al 2 O 3 passivation is due to not only a sufficiently low interface defect density but also a high density of built-in negative charges. A 7 nm thin Al 2 O 3 film can yield an emitter saturation current density of ~8 fA/cm 2 on high sheet resistance p + layer, compared to ~60 and ~1480 fA/cm 2 for thermal SiO 2 and SiN x passivation. This superior surface passivation allows the photon-generated carriers to have higher probabilities to reach the high-field region to trigger an avalanche event. In addition, Al 2 O 3 thin film provides very low values of effective surface recombination velocity on low resistivity n-type and p-type Si surfaces, which can lead to well-passivated surface features on guard ring and trench isolation regions of SiPM. These demonstrate the potential of Al 2 O 3 thin film passivation to improve quantum efficiency and thus photo-detection efficiency of ultraviolet sensitive SiPM with p + /n - /n/n + structure.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Plasma enhanced atomic layer deposition of thin film Li 1+x Mn 2-x O 4 for realization of all solid-state 3D lithium-ion microbatteries

Here, the plasma enhanced atomic layer deposition (PEALD) process for MnO 2 was demonstrated, exhibiting self-limiting growth as well as stable composition and stable growth rate over a temperature window of 205–265 °C. The PEALD process for MnO 2 was combined with the thermal ALD process for LiOH to synthesize Li 1+x Mn 2-x O 4 thin film cathodes, where the stoichiometry was effectively controlled to allow for crystallization in the electrochemically active spinel phase. A 3D nanostructure consisting of an Li 1+x Mn 2-x O 4 cathode layer, ALD Li x Al y Si z O solid electrolyte, and SiGe nanowire anode was fabricated and characterized via TEM. The Li 1+x Mn 2-x O 4 thin films maintained 66% of the areal capacity upon a 100× increase in the rate (4–360 μ A cm -2 ) as well as 97% capacity retention over 100 cycles at ~5C. The ALD Li 1+x Mn 2-x O 4 thin films exhibited a volumetric capacity of 52 μ Ah cm -2 μ m -1 at a C-rate of ~0.5C and, coupled with the high operating voltage (4.0 V), offer some of best areal energy densities for ALD thin film cathodes, making it a viable material for integration with 3D lithium-ion microbatteries.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Performance and reliability of β-Ga 2 O 3 Schottky barrier diodes at high temperature

Beta-gallium oxide (ß-Ga 2 O 3 ) is an ultrawide bandgap semiconductor that has potential for power electronic applications and devices operating at high temperatures. Particularly important for these applications are its 4.9 eV bandgap, facile electron doping, and the ability to grow ß-Ga 2 O 3 crystals from the melt. In this work, vertical ß-Ga 2 O 3 Schottky barrier diodes were fabricated using Pt Schottky and Ti-based Ohmic contacts and Au contact pads on unintentionally doped n-type, (2¯01)-oriented single crystal substrates. The diode’s temperature-dependent electrical properties up to 400°C were investigated, and the Pt/Ga 2 O 3 Schottky barrier height was determined to be close to 1.2 eV. The degradation of the contacts over multiple cycles up to 400°C was observed, resulting in a significant increase in series resistance of the diodes by 1000× at ambient temperature after they were cycled. According to electron microscopy measurements, this degradation is likely due in part to the migration and oxidation of Ti at the top surface of the Au contact pads. This degradation highlights the need for further research and development to ensure stable Ohmic and Schottky contacts to Ga 2 O 3 at temperatures above 400°C.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Redundancy in Aromatic O -Demethylation and Ring-Opening Reactions in Novosphingobium aromaticivorans and Their Impact in the Metabolism of Plant-Derived Phenolics

ABSTRACT Lignin is a plant heteropolymer composed of phenolic subunits. Because of its heterogeneity and recalcitrance, the development of efficient methods for its valorization still remains an open challenge. One approach to utilize lignin is its chemical deconstruction into mixtures of monomeric phenolic compounds, followed by biological funneling into a single product. Novosphingobium aromaticivorans DSM 12444 has been previously engineered to produce 2-pyrone-4,6-dicarboxylic acid (PDC) from depolymerized lignin by simultaneously metabolizing multiple aromatics through convergent routes involving the intermediates 3-methoxygallic acid (3-MGA) and protocatechuic acid (PCA). We investigated enzymes predicted to be responsible for O -demethylation and oxidative aromatic ring opening, two critical reactions involved in the metabolism of phenolic compounds by N. aromaticivorans . The results showed the involvement of DesA in O -demethylation of syringic and vanillic acids, LigM in O- demethylation of vanillic acid and 3-MGA, and a new O- demethylase, DmtS, in the conversion of 3-MGA into gallic acid (GA). In addition, we found that LigAB was the main aromatic ring-opening dioxygenase involved in 3-MGA, PCA, and GA metabolism and that a previously uncharacterized dioxygenase, LigAB2, had high activity with GA. Our results indicate a metabolic route not previously identified in N. aromaticivorans that involves O -demethylation of 3-MGA to GA. We predict that this pathway channels ∼15% of the carbon flow from syringic acid, with the rest following ring opening of 3-MGA. The new knowledge obtained in this study allowed for the creation of an improved engineered strain for the funneling of aromatic compounds that exhibits stoichiometric conversion of syringic acid into PDC. IMPORTANCE For lignocellulosic biorefineries to effectively contribute to reduction of fossil fuel use, they need to become efficient at producing chemicals from all major components of plant biomass. Making products from lignin will require engineering microorganisms to funnel multiple phenolic compounds to the chemicals of interest, and N. aromaticivorans is a promising chassis for this technology. The ability of N. aromaticivorans to efficiently and simultaneously degrade many phenolic compounds may be linked to having functionally redundant aromatic degradation pathways and enzymes with broad substrate specificity. A detailed knowledge of aromatic degradation pathways is thus essential to identify genetic engineering targets to maximize product yields. Furthermore, knowledge of enzyme substrate specificity is critical to redirect flow of carbon to desired pathways. This study described an uncharacterized pathway in N. aromaticivorans and the enzymes that participate in this pathway, allowing the engineering of an improved strain for production of PDC from lignin.

Biotechnology & Applied Microbiology↗
DOE OSTI2023

FY2023 Status Report: Model 9975 O-Ring Fixture Long-Term Leak Performance

Leak testing experiments to monitor the aging performance of Viton ® GLT and GLT-S O-rings used in the model 9975 shipping package has been ongoing since 2004 at Savannah River National Laboratory. Seventy tests using mock-up 9975 primary containment vessels (PCVs) with GLT O-rings were assembled and heated to temperatures ranging from 200 to 450 °F. Due to material substitution, fourteen tests with GLT-S O-rings were initiated in 2008 and heated to temperatures ranging from 200 to 400 °F. The conditioning temperatures are elevated compared to the calculated maximum O-ring temperature in a 9975 package in storage, 158 °F, to accelerate aging and enable observations of O-ring failures in a reasonable time frame.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2022

Hall Effect Study of the Metamagnetic Transition in the Sr 4 (Ru 0.99 Fe 0.01 ) 3 O 10 Nanosheet

Sr 4 (Ru 0.99 Fe 0.01 ) 3 O 10 shows a ferromagnetic (FM) transition at T C ~ 105 K with the magnetic easy axis in the ab plane, followed by a metamagnetic transition (MMT) at low temperatures when the magnetic field H is applied along the c axis, which is in sharp contrast to that of the pure Sr 4 Ru 3 O 10 , where the easy axis is along the c axis and the MMT is in the ab plane. Here, we studied the MMT in the Sr 4 (Ru 0.99 Fe 0.01 ) 3 O 10 nanosheet by the Hall effect. It was found that the ordinary Hall coefficient of Sr 4 (Ru 0.99 Fe 0.01 ) 3 O 10 is almost the same as that of the pure Sr 4 Ru 3 O 10 , while a sudden increase in the Hall resistance R xy is observed below ~50 K, above which the R xy presents the conventional anomalous Hall effect up to T C . Analysis of the results indicates that the MMT has no direct correlation to the electronic structure but closely relates to the magnetic moment locking, where the magnetic-field-induced breakdown of the locked moments is responsible for the MMT.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Structure and Anharmonicity of α- and β -Sb 2 O 3 at Low Temperature

Antimony oxides are important materials for catalysis and flame-retardant applications. The two most common phases, α-Sb 2 O 3 (senarmontite) and β-Sb 2 O 3 (valentinite), have been studied extensively. Specific focus has been placed recently on their lattice dynamics properties and how they relate to the α-β phase transformation and their potential anharmonicity. However, there has not been any direct investigation of anharmonicity in these systems, and a surprising lack of low-temperature structural information has prevented further study. Here, we report the powder neutron diffraction data of both phases of Sb 2 O 3 , as well as structural information. α-Sb 2 O 3 behaved as expected, but β-Sb 2 O 3 revealed a small region of zero thermal expansion along the c axis. Additionally, while the β phase matched well with reported atomic displacement parameters, the α phase displayed a marked deviation. This data will enable further investigations into these systems.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Inductively Coupled Nonthermal Plasma Synthesis of Size-Controlled γ-Al 2 O 3 Nanocrystals

Gamma alumina (γ-Al 2 O 3 ) is widely used as a catalyst and catalytic support due to its high specific surface area and porosity. However, synthesis of γ-Al 2 O 3 nanocrystals is often a complicated process requiring high temperatures or additional post-synthetic steps. Here, we report a single-step synthesis of size-controlled and monodisperse, facetted γ-Al 2 O 3 nanocrystals in an inductively coupled nonthermal plasma reactor using trimethylaluminum and oxygen as precursors. Under optimized conditions, we observed phase-pure, cuboctahedral γ-Al 2 O 3 nanocrystals with defined surface facets. Nuclear magnetic resonance studies revealed that nanocrystal surfaces are populated with AlO 6 , AlO 5 and AlO 4 units with clusters of hydroxyl groups. Nanocrystal size tuning was achieved by varying the total reactor pressure yielding particles as small as 3.5 nm, below the predicted thermodynamic stability limit for γ-Al 2 O 3 .

77 NANOSCIENCE AND NANOTECHNOLOGY↗
DOE OSTI2026

Bandgap Engineering of Ga 2 O 3 by MOCVD Through Alloying with Indium

Ga 2 O 3 and In 2 O 3 are vital semiconductors with current and future electronic device applications. Here, we study the alloying of In 2 O 3 and Ga 2 O 3 (IGO) and the associated changes in structure, morphology, band gap, and electrical transport properties. Undoped films of IGO were deposited on sapphire substrates with varying indium (In) percentage from zero to 100% by metal-organic chemical vapor deposition (MOCVD). Some films were annealed in H 2 to induce electrical conductivity. The measurements showed the optical band gap decreased by adding In; this was confirmed by density functional (DFT) calculations, which revealed that the nature of the valence band maximum and conduction band minimum strongly relate to the chemistry and that the band gap drops by adding In. The as-grown films were highly resistive except for pure In 2 O 3 , which possesses p-type conductivity, likely arising from In vacancy-related acceptor states. N-type conductivity was induced in all films after H-anneal. DFT calculations revealed that the presence of In decreases the electron effective mass, which is consistent with the electrical transport measurements that showed higher electron mobility for higher In percentage. The work revealed the successful band gap engineering of IGO and the modification of its band structure while maintaining high-quality films by MOCVD.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Presupernova O–C Shell Mergers Could Produce More 44 Ti than the Explosion

The formation of 44 Ti in massive stars is thought to occur during explosive nucleosynthesis; however, recent studies have shown it can be produced during O–C shell mergers prior to core collapse. We investigate how mixing according to 3D macrophysics derived from hydrodynamic simulations impacts presupernova O–C shell merger nucleosynthesis and if it can dominate explosive supernova production of 44 Ti and other radioactive isotopes. We compare a range of observations and models of explosive 44 Ti yields to preexplosive multizone mixing–burning nucleosynthesis simulations of an O–C shell merger in a 15 M ⊙ Z = 0.02 stellar model with mixing conditions corresponding to different 3D hydrodynamic mixing scenarios. Radioactive species produced in the O shell have a multidex spread in preexplosive yield predictions across different 3D mixing scenarios of 1.54 and 2.14 dex on average, depending on mass cut. 44 Ti has the largest spread of 4.78 and 4.81 dex depending on mass cut. Further, we show that the preexplosive production of 44 Ti can be larger than the explosive production of models and can match observations. Our results also show that 3D mixing physics enhances 44 Ti in 1D models without modifying 56 Ni yields. We conclude that quantitative predictions of 44 Ti and other radioactive species more broadly require an understanding of the 3D hydrodynamic mixing conditions present during the O–C shell merger.

Issa, Joshua [University of Victoria, BC (Canada);↗
DOE OSTI2022

Dependence of Narrow-line Region Sizes on [O III ] Luminosity in Low-redshift Active Galactic Nuclei with Double-peaked Broad Balmer Emission Lines

In this paper, simple but interesting results are reported on the upper limits of narrow-line region (NLR) sizes of a small sample of 38 low-redshift (z < 0.1) active galactic nuclei (AGN) with double-peaked broad emission lines (double-peaked BLAGN), in order to check whether the NLR sizes in type-1 AGN (broad line) and type-2 AGN (narrow line) obey a similar empirical dependence on [O III ] luminosity. In order to correct the inclination effects on projected NLR sizes of type-1 AGN, the accretion disk origin is commonly applied to describe the double-peaked broad Hα line, leading to the determined inclination angles of central disk-like broad-line regions of 38 double-peaked BLAGN. Then, considering the fixed Sloan Digital Sky Survey (SDSS) fiber radius, the upper limits of the NLR sizes of the 38 double-peaked BLAGN can be estimated. Meanwhile, a strong linear correlation between continuum luminosity and [O III ] luminosity is applied to confirm that the [O III ] emissions of the 38 double-peaked BLAGN are totally covered in the SDSS fibers. Considering the reddening-corrected measured [O III ] luminosity, the upper limits of the NLR sizes of the 38 double-peaked BLAGN are within a 99.9999% confidence interval of the expected results from the empirical relation between NLR size and [O III ] luminosity in type-2 AGN. In the current understanding, there are no challenges to the unified model of AGN through the space properties of NLRs.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2026

Data from: Coupled machine learning-ecosystem ensemble models substantially improve predictions of nitrous oxide (N 2 O) fluxes from US croplands

Nitrous oxide (N₂O) is a potent and persistent greenhouse gas, with rising atmospheric concentrations driven in part by inefficient use of synthetic nitrogen (N) fertilizers in agriculture. Predicting soil N₂O emissions is challenging due to high spatial and temporal variability arising from complex soil biogeochemical processes. Process-based ecosystem models and standalone machine learning (ML) approaches without extensive site-specific calibration often miss high emission episodes. Here, we show how an Ensemble Modeling System (EMS) based on outputs from an ensemble of ecosystem models coupled to an ensemble of ML models can improve predictions and understanding of N2O fluxes from US cropland. Trained and validated on approximately 12,000 N2O chamber measurements at 17 U.S. Midwest sites (six crops, 35 management practices), the EMS accurately predicted daily fluxes of N2O at both training (R² = 0.84, RMSE = 16.4 g N ha⁻¹ d⁻¹) and held-out testing sites (R² = 0.84, RMSE = 6.2 g N ha⁻¹ d⁻¹). Analyses identified six dominant N₂O drivers: soil organic carbon (SOC), NH₄⁺, NO₃⁻, water-filled pore space (WFPS), soil temperature, and biomass production. Wet, warm soils produced large N₂O peaks only with sufficient SOC and mineral N; in low-SOC soils, fluxes remained low. Incorporating these drivers into process-based models might significantly improve their predictive capacity. The EMS demonstrates a strong potential to predict N₂O fluxes at unseen sites, enabling more reliable regional inventories, improved gap-filling where measurements are sparse, and enhanced understanding of mechanisms to advance targeted mitigation strategies in food, feed, and bioenergy crops.

agricultural sciences↗
DOE OSTI2025

Build-To-Replace Strategy to Reduce O&M Costs of Advanced Reactors

This paper targets the goal of reducing fixed operations and maintenance (O&M) costs to $2/MWh for advanced reactor (AR) designs, an order of magnitude reduction from current nuclear fleets. Such goal will be severely constrained if the underlying assumptions of O&M approaches and practices are not questioned and reexamined, especially today when changes can be implemented effectively and efficiently. Achieving a 90% reduction in AR O&M costs requires a completely new way of thinking – a paradigm shift – not through incremental, technology-focused approaches alone. Here, we address this challenge by evaluating the impact of moving to shorter design life for major structures, systems and components (SSCs) and shorter, more predictable refurbishment cycles as modeled by the commercial airline industry. This paper provides a brief overview of this different mindset to O&M applied to ARs: the build-to-replace approach. We provide a direct example of analysis of a build-to-replace scenario by identifying and evaluating scenarios for reduced system and component lifetimes and associated replacement and refurbishment schedules to evaluate impacts on O&M costs and other lifecycle elements such as SSC reliability.

97 - MATHEMATICS AND COMPUTING↗
DOE OSTI2020

Research advances on cobalt-free cathodes for Li-ion batteries - The high voltage LiMn 1.5 Ni 0.5 O 4 as an example

LiMn 1.5 Ni 0.5 O 4 is one of the most promising cathode materials for use in either next generation lithium-ion batteries or all solid-state batteries. However, despite the significant Research and Development (R&D) carried out throughout the last two decades the material has not made serious inroads into market. One of the major reasons is the lack of consistency in the reported intrinsic properties and electrochemical performance owing to major controversies in synthesis, crystal structure and bulk and interfacial properties of LiMn 1.5 Ni 0.5 O 4 , notably in contact with electrolytes. This paper is a compelling review providing an assessment on the mainstream R&D dealing with the various crystal structures of LiMn 1.5 Ni 0.5 O 4 and their evolutions observed during synthesis and cycling in correlation with their electrochemical performance. Influence of electrolytes and additives along with modifications through doping and surface treatments are interrelated, and the electronic and ionic transport properties of the ordered and disordered LiMn 1.5 Ni 0.5 O 4 phases are discussed. Overall, this review provides a detailed assessment on LiMn1.5Ni0.5O4 and the underlying mechanisms governing its electrochemical performance broadly providing a focused framework for further advancement towards commercialization.

25 ENERGY STORAGE↗
DOE OSTI2021

Al 2 O 3 /TiO 2 coated separators: Roll-to-roll processing and implications for improved battery safety and performance

Heat generation is one of the major concerns with lithium-ion batteries (LIB) while charging them at higher currents, which could inadvertently impact the rate performance and reduce the safety of the cell. Polymer separator is one of the least thermal conductive components of a LIB. In addition, commercial separators for LIB are made from polyolefin membranes that tend to shrink and curl at higher temperatures due to their lower melting temperature (~130 °C). Developing separators with improved thermal stability and higher electrolyte uptake is essential for enhancing the safety as well as the performance of the LIB. In this work, a thin layer of ceramic coatings (Al 2 O 3 and TiO 2 ) is applied on propylene (PP) membrane to improve the thermal stability and electrolyte affinity without compromising the rate performance. A slurry with 100% Al 2 O 3 coated on the polypropylene separator exhibited the best improvement in thermal stability ( shrinkage of 0.6% vs 6.0% for uncoated membrane) and excellent rate performance with 92% capacity retention at 2C. The Al 2 O 3 coated separator demonstrated excellent electrolyte wettability compared to the uncoated membrane. The cross-plane thermal conductivity of the ceramic coated separators is analyzed to understand their heat transfer behavior. The thermal conductivity of the separator is improved by ~3.2 times with the Al 2 O 3 coating.

25 ENERGY STORAGE↗
DOE OSTI2025

Structural Distortions and Uniaxial Negative Thermal Expansion in the Polar Dion–Jacobson Oxide RbNdTa 2 O 7

We provide deeper insight into the crystal structures, sequential structural phase transitions (I2cm → Cmce → I4/mcm → P4/mmm), thermal expansion, and electronic properties of the n = 2 Dion–Jacobson polar oxide RbNdTa 2 O 7 , through X-ray powder diffraction, neutron powder diffraction, Raman studies, and density functional theory calculations. We observed a uniaxial negative thermal expansion (NTE) across the first-order transition, I2cm → Cmce, where the unit cell contracts along the c-axis, which is driven by a contraction of the NdTa 2 O 6 layer. Here, this NTE occurs within the temperature range of the first-order phase transition and contrasts with the corkscrew mechanism typically observed in Ruddlesden–Popper phases. In RbNdTa 2 O 7 , the I2cm (hybrid improper ferroelectric) → Cmce (antipolar) transition involves crucial changes in the bond lengths of Nd and Ta polyhedra, coupled with polar to antipolar displacement of the Nd ions, leading to a net contraction in the NdTa 2 O 6 layer along the c-axis, while preserving the overall octahedral tilting magnitude. This transition highlights the intricate interplay between the Nd and Ta coordination and the associated TaO 6 distortions. Temperature-dependent Raman spectra analysis further confirms the first-order structural transition and associated NTE, providing evidence for increased bond stiffness across this transition. Additionally, using neutron powder diffraction, we have determined that the transition I4/mcm → P4/mmm occurs at approximately 1150 K. Finally, we have calculated from DFT + U, the partial density of states, the energy bandgaps, and effective masses of the charge carriers of the polar ground structure.

Chemical structure↗
DOE OSTI2023

Theoretical Kinetics Predictions for Reactions on the NH 2 O Potential Energy Surface

Recent modeling studies of ammonia oxidation, which are motivated by the prospective role of ammonia as a zero-carbon fuel, have indicated significant discrepancies among the existing literature mechanisms. In this study, high-level theoretical kinetics predictions have been obtained for reactions on the NH 2 O potential energy surface, including the NH 2 + O, HNO + H, and NH + OH reactions. These reactions have previously been highlighted as important reactions in NH 3 oxidation with high sensitivity and high uncertainty. The potential energy surface is explored with coupled cluster calculations, including large basis sets and high-level corrections to yield high-accuracy (~0.2 kcal/mol 2σ uncertainty) estimates of the stationary point energies. Variational transition state theory is used to predict the microcanonical rate constants, which are then incorporated in master equation treatments of the temperature- and pressure-dependent kinetics. For radical–radical channels, the microcanonical rates are obtained from variable reaction coordinate transition state theory implementing directly evaluated multireference electronic energies. The analysis yields predictions for the total rate constants as well as the branching ratios. We find that the NO + H 2 channel contributes 10% of the total NH 2 + O flux at combustion temperatures, although this channel is not included in modern NH 3 oxidation mechanisms. Modeling is used to illustrate the ramifications of these rate predictions on the kinetics of NH 3 oxidation and NO x formation. Finally, the present results for NH 2 + O are important for predicting the chain branching and formation of NO in the oxidation of NH 3 and thermal DeNO x .

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗