Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “NANOPARTICLES”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Atmospheric clusters to nanoparticles: Recent progress and challenges in closing the gap in chemical composition

Aerosol nanoclusters (AN), defined here as molecular aggregates suspended in a gas with dimensions between 2 and 10 nm, are the link between substances that we think of as molecules, or the “gas phase,” and those that we consider as particles, or the “condensed phase.” The ability to measure and model the physical and chemical properties of size-resolved AN, which at present is rudimentary at best, is crucial for understanding how particles form and evolve in a number of environments that are natural or influenced by human activities. This review describes the current state-of-the-art for measuring and modeling the size-resolved composition of atmospheric AN. We focus specifically on instruments, many relying on mass spectrometry, that show promise for closing the measurement gap under atmospherically relevant conditions by increasing the size of measurable gas-phase clusters (bottom-up approaches) and by decreasing the size of measurable nanoparticles (top-down approaches). Theoretical methods for predicting AN composition have similarly relied on bottom-up approaches that extend the accuracy of quantum chemistry calculations to larger molecular systems, as well as top-down approaches that correct bulk composition aerosol models for size-dependent properties such as viscosity and volatility. Finally, current measurement and modeling challenges that must be overcome in order to close the gap are discussed.

42 ENGINEERING↗

A molecular dynamics survey study of impact-induced amorphization in yttria nanoparticles

The impact of a single yttria (Y 2 O 3 ) nanoparticle onto a yttria substrate was studied as a function of particle velocity (300–1200 m/s) and diameter (5–12 nm) for three particle orientations and two substrate orientations using molecular dynamics simulations. Impacts resulted in minimal dislocation motion but extensive disordering of the crystal lattice without approaching the melting temperature. The resulting amorphous microstructure was both precisely coincident with plastic strain and retained until the end of the simulation, suggesting a deformation mechanism of amorphization-facilitated viscous flow. Further analysis revealed that the degree of amorphization depended primarily on the impact velocity and secondarily on the orientations of the particle and substrate, with significant second-order effects from variable interactions.

74 ATOMIC AND MOLECULAR PHYSICS↗

Medium controlled aggregative growth as a key step in mesoporous silica nanoparticle formation

Near monodisperse mesoporous silica nanoparticles (MSN) represent a promising and rapidly developing type of mesoporous silica materials; however, the vast data on their synthesis remains unorganized and ill-understood. We systematically studied the formation of MSN under basic and neutral conditions using various temperatures, CTAB concentrations, hydrolyzing agents (triethanolamine, ammonia, phosphate buffers), and media with different colloidal stabilization properties (with ethanol as a cosolvent and monovalent salts). In the typical conditions for the preparation of stable MSN colloids, the particle size was controlled by colloidal stabilization by the medium (solvent type, ionic strength, and surfactant concentration) in agreement with the “aggregative growth” mechanism, rather than by solely the hydrolysis and condensation rates conventionally used for data interpretation in the classical nucleation theory. Medium properties (pH, ion types and concentration, polarity) also defined the efficiency of silica-surfactant cooperative self-assembly, which directly affected the porosity, mesopore size and pore wall thickness. Interestingly, this traditional silica-surfactant route showed a limited effect on the particle size, emphasizing the dominating role of colloidal stabilization in the studied reaction conditions. In situ pH measurements showed that every reaction medium has unique pH evolution profiles depending on the buffer capacity, hydrolysis and condensation rates. Reaction systems that fail to maintain the working pH can lead to non-porous products or undesired particle morphology and size distribution. The established particle formation mechanism allowed us to formulate comprehensive guidelines for preparing relatively concentrated colloids of near monodisperse (PDI 5–15%) mesoporous 30–700 nm silica spheres with variable porosity and mesopore size. Here, these findings will be particularly useful in designing new mesoporous silica-containing materials for biomedical applications.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Green synthesis and characterization of nontoxic L-methionine capped silver and gold nanoparticles

The simple green method for synthesis of stable L-Methionine (L-Met) capped silver (Ag@LM NPs) and gold (Au@LM NPs) nanoparticles (NPs) without adding any additional reduction agent or stabilizer was developed. Colloidal dispersions were characterized by UV–Vis spectrophotometry. The size and spherical shape of NPs were evaluated by transmission electron microscopy. Their surface covering was confirmed by atomic force microscopy, Fourier transform infrared spectroscopy, dynamic light scattering, and zeta potential measurements. Density functional theory calculations pointed that the preferential adsorption mode of L-Met on both Ag and Au surfaces was a vertical binding geometry via –NH2 group, while horizontal binding mode via [sbnd]S[sbnd] and –NH2 groups is also possible. The genotoxicity (evaluated by the micronucleus assay) of NPs, as well as their effects on some oxidative stress parameters (catalase activity, malondialdehyde level), were assessed in vitro using human peripheral blood cells as a model system. The influence of NPs on the morphology of lymphocyte cells studied using atomic force microscopy revealed that the membrane of cells remained unaffected after the treatment with NPs. When considering the effects of NPs on catalase activity and malondialdehyde level, neither particle type promoted oxidative stress. However, the treatment of lymphocytes with Ag@LM NPs induced a concentration-dependent enhancement of the micronuclei incidence and suppression of the cell proliferation while Au@LM NPs promoted cell proliferation, with no significant effects on micronuclei formation. The Ag@LM NPs were more prone to induce DNA damage than Au@LM NPs, which makes the latter type more suitable for further studies in nano-medicine. © 2019.

60 APPLIED LIFE SCIENCES↗

An organogel library for solution NMR analysis of nanoparticle suspensions in non-aqueous samples

Surface contrast solution NMR methods (scNMR) are emerging as powerful tools to investigate the adsorption of small molecule ligands to the surface of nanoparticles (NP), returning fundamental insight into the kinetics and thermodynamics of sorption, as well as structural information on the adsorbed species. A prerequisite for the acquisition of high quality solution NMR data is the preparation of homogeneous and stable samples that return consistent NMR spectra and allow extensive signal averaging. Unfortunately, this condition does not apply to NMR samples containing NPs that often show a tendency to sediment and accumulate at the bottom of the NMR tube over the course of the experiment. We have recently shown that preparing NMR samples in an agarose gel matrix inhibits sedimentation and allows the characterization of small molecule-NP interactions by scNMR. Unfortunately, as the agarose gel only forms in aqueous solution, this sample preparation method cannot be used to stabilize NP suspensions in a non-aqueous environment. In this work, we introduce a library of 48 organogels, based on low molecular-mass organic gelators (LMOGs), to prepare NMR samples of small molecule/NP systems in a wide range of organic solvents. In addition, we present a simple method that takes advantage of 1H transverse relaxation (1H-R2) measurements to screen the library and identify the best gelator to characterize the small molecule-NP interaction of interest in the solvent of choice. We expect the results of this study will enable the preparation of homogeneous and stable samples of NPs in non-aqueous environments, therefore dramatically increasing the applicability of scNMR to the characterization of heterogeneous interactions and to the investigation of the role played by solvent molecules in regulating the kinetics and thermodynamics of sorption.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Leakoff assessment of nanoparticle-stabilized CO 2 foams for fracturing applications

The leakoff of multiphase systems through porous media is a complicated process. In this study, we have designed an experimental setup that is used to assess the leakoff of the liquid and gas phase under pressurized conditions. The novelty of this study is that while most previous studies utilized fluid/gas in the aqueous phase, nanoparticles are introduced in this study, which formed a solid/fluid/gas multiphase system to boost foam performance and reduce leakoff. In the parametric experimental analysis, the effects of foam quality, core permeability, surfactant concentration, and polymer concentration on the dynamic and static leakoff rates of liquid and gas are evaluated. It was found that core permeability affects the leakoff of foam the most with a leakoff coefficient of up to 1.37015 $ft/\sqrt{min}$ for gas and up to 0.1056 $ft/\sqrt{min}$ for liquid under the experiment settings herein. The leakoff rate of gas is generally several magnitudes higher than that of the liquid. When CO 2 gas is present in the foam, the leakoff coefficient falls in the range between 0 and 1.37015 $ft/\sqrt{min}$ for gas, and between 0.0005 and 0.1056 $ft/\sqrt{min}$ for liquid. Finally, the methodology and results of this study shed light on the mechanistic understanding of the leakoff properties of multiphase systems and could be used to assist the design of foam fracturing for reservoir stimulation.

03 NATURAL GAS↗

Copper(I) photosensitizer-silica nanoparticle assembly towards enhanced aqueous photoluminescence

Harnessing the luminescence potential of Cu(I) complexes in aqueous media is typically hindered by their poor photostability and altered properties. Here, we report the synthesis, engineering and morphological characterization of a hydrophobic homoleptic copper(I) complex entrapped into silica nanoparticles, Cu-I@SiO 2 (where “Cu-I” designates [Cu(2,9-diiodo-1,10-phenanthroline) 2 ] + ), as a promising stabilisation strategy towards water-compatible, Cu(I) complex-based luminescence. The polyether chain-decorated nano-objects are spherical with an average diameter of ca. 10.8 ± 1.9 nm. Upon dispersion in water, clear solution-like suspensions were obtained. Significantly, the aqueous suspensions photo-luminesce (Φ em = 5×10 -4 ) upon excitation through the Metal-to-Ligand Charge-Transfer transition (MLCT) of the embedded copper(I) complexes. In contrast, the corresponding silica-free molecular complex dissolved in an aqueous environment revealed fully quenched emission. Finally, the use of Cu-I@SiO 2 suspensions as luminescent probes is reported, first by assessing their potential use as electrochemiluminescent probes, and second by monitoring the photoluminescence from Cu-I@SiO 2 in the presence of whole blood.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Carbon molecular sieve hollow fiber membranes derived from dip-coated precursor hollow fibers comprising nanoparticles

We report a novel approach to economically fabricate dual-layer composite nanoparticle-containing carbon molecular sieve (CMS) hollow fiber membranes having excellent gas separation performance. The economically favored process comprises dip coating engineered support layer fibers to form a dense skin layer in a CMS precursor. The coated fibers are then pyrolyzed to form a high-performance CMS hollow fiber membrane. The nano-particle containing composite carbon molecular sieve hollow fiber membranes showed very attractive selectivities and productivities. As a result, this work shows how to produce high performance CMS hollow fiber membrane by coating, which exceeds that achieved with the standard sol-gel support stabilization technique.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Electrochemically decorated gold nanoparticles on CVD graphene ChemFET sensor for the highly sensitive detection of As(III)

Here, in this paper, we report a novel reusable receptor-free chemically sensitive field-effect transistor (ChemFET) sensor for the sensitive detection of As(III) using electrochemical doping of Au nanoparticles (AuNPs)-chemical vapour deposition (CVD) graphene (Gr) sensing film (AuNPs-Gr). The sensor consists of a single-gap gold electrode and a single layer of CVD graphene as a conducting/sensing channel decorated with a thin layer of electrochemically deposited AuNPs to catalyze the electroreduction of As(III) ions onto the sensing channel. A new detection strategy was proposed by measuring the resistance change rate of the AuNPs-Gr sensing channel modified between the source electrode and drain electrode, wherein the resistance change was caused by the electrochemical doping of As(0). The results indicated that the electrochemical doping of As(0) onto the sensing channel led to an increase in resistance through the doping interaction among As(0), AuNPs and graphene, enabling the proposed sensor to have an extraordinary detection performance with a high sensitivity. Moreover, the proposed sensor can be recycled by removing the As(0) deposited on the sensing film with the aid of a simple electrochemical oxidization process. Additionally, the mechanism of the sensing strategy based on the electrochemical n-doping of As(0) into the AuNPs-Gr sensing film was investigated using a top liquid gate electrode. The As(III) concentration detected by the AuNPs-Gr ChemFET sensor was as low as 0.001 μg/L, demonstrating that such sensors with a compatible sensing strategy can be used to detect As(III) with high sensitivity, easy fabrication, fast response and can be recycled.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

High-efficiency, air-stable manganese–iron oxide nanoparticle-pigmented solar selective absorber coatings toward concentrating solar power systems operating at 750 °C

Solar selective absorber coating with long-term thermal stability at high temperatures ≥750 °C in air is an important component to reduce the levelized cost of energy (LCOE) of concentrating solar power (CSP) systems toward 50% power efficiency and dispatchable solar electricity. Conventionally, solar spectral selectivity requires multilayer-interference coatings implemented by stringently controlled vacuum deposition, and these coatings degrade significantly at >700 °C in air. Herein, we established a quantitative design approach and demonstrated a proof-of-concept air-stable, manganese–iron oxide nanoparticle (NP)-pigmented solar selective coatings with a high solar absorptance of ~93%, a relatively low thermal emittance of ~52%, and an optical-to-thermal energy conversion efficiency >89% under 1,000× solar concentration at 750 °C toward Generation 3 CSP systems. These coatings demonstrate spectral selectivity using cost-effective spray coating approach, a notable improvement over conventional vacuum-deposited, multilayer solar selective coatings for low-cost, high-efficiency solar thermal receivers. In contrast to the thermal degradation of spectrally non-selective benchmark Pyromark 2500 coatings at 750 °C in air, the solar absorptance of the MnFe 2 O 4 -pigmented coatings on stainless steel 310 (SS 310) substrates is increased to ~92.9% and the optical-to-thermal energy conversion efficiency is improved to 89.7% after serving at 750 °C in air for 700 h. X-ray diffraction results reveal that this improvement is due to the transformation of MnFe 2 O 4 NPs into more thermodynamically stable, non-stoichiometric manganese-rich manganese ferrite and iron-rich manganese–iron oxide phases after 500 h aging at 750 °C. For >1,000 h-endurance testing at 750 °C in air and the subsequent 19 day-night thermal cycling between 750 °C (12 h/cycle) and 25 °C (12 h/cycle) on SS 310 substrates, the thermal degradation is mainly due to the CrO x microflake formation from SS 310 substrates rather than the coatings, which can be suppressed by preoxidizing the surface of SS 310. With lower emittance matrix material and further optimization of pigment NP stoichiometry, concentration, and coating thickness, it is promising to achieve an optimized thermal efficiency ≥92.5% with long-term thermal stability at 750 °C for Generation 3 CSP systems.

14 SOLAR ENERGY↗

Utilizing the unique charge extraction properties of antimony tin oxide nanoparticles for efficient and stable organic photovoltaics

Simultaneously enhancing device performance and longevity, as well as balancing the requirements on cost, scalability, and simplification of processing, is the goal of interface engineering of organic solar cells (OSCs). In our work, we strategically introduce antimony (Sb 3+ ) cations into an efficient and generic n-type SnO 2 nanoparticles (NPs) host during the scalable flame spray pyrolysis synthesis. Accordingly, a significant switch of conduction property from an n-type character to a p-type character is observed, with a corresponding shift in the work function (WF) from 4.01 ± 0.02 eV for pristine SnO 2 NPs to 5.28 ± 0.02 eV for SnO 2 NPs with 20 mol. % Sb content (ATO). Both pristine SnO 2 and ATO NPs with fine-tuned optoelectronic properties exhibit remarkable charge carrier extraction properties, excellent UV resistance and photo-stability being compatible with various state-of-the-art OSCs systems. The reliable and scalable pristine SnO 2 and ATO NPs processed by doctor-blading in air demand no complex post-treatment. Our work offers a simple but unique approach to accelerate the development of advanced interfacial materials, which could circumvent the major existing interfacial problems in solution-processed OSCs.

14 SOLAR ENERGY↗

Influence of calcium nitrate timing on the structural and textural characteristics of mesoporous SiO 2 -CaO nanoparticles

Mesoporous bioactive glass nanoparticles (MBGNPs) are promising materials for drug delivery due to their high pore volume and specific surface area. This study investigates how the timing of calcium nitrate addition affects the structural and textural characteristics of MBGNPs synthesized via a microemulsion-assisted sol-gel method. Delayed calcium nitrate addition reduced calcium incorporation from 14.2 to 9.5 mol% and increased particle size from 178 ± 51 nm to 256 ± 30 nm. The specific surface area values increased with the delayed addition of calcium nitrate, as observed through BET and USAXS/SAXS measurements. The proportion of Q Si n units slightly changed, but no cytotoxicity was observed in osteoblast-like cells. These findings provide valuable insights into optimizing MBGNP synthesis for biomedical applications.

Calcium nitrate tetrahydrate↗

Copper iodide nanoparticles as a hole transport layer to CdTe photovoltaics: 5.5 % efficient back-illuminated bifacial CdTe solar cells

We report the role of copper iodide (CuI) nanoparticles (NPs) as a hole transport layer (HTL) in cadmium sulfide/cadmium telluride (CdS/CdTe) photovoltaics. These CuI NPs were prepared using solution processing at room temperature and used to fabricate monofacial and bifacial CdTe solar cells with different back contacts. Using CuI/Au as the back contact, the device efficiency reached to 14.8% with outstanding fill factor (FF) of 79.2%. Replacing the gold (Au) electrode with sputtered transparent indium tin oxide (ITO), a CuI/ITO back contact yielded photoconversion efficiencies (PCEs) of 11.6% and 5.5% under front and back illumination respectively. Bifacial devices (CdTe/ITO) without the CuI NP HTL have an efficiency of 7.0% and 1.0% for front and back illumination, respectively. For CuI/ITO, a current collection of 12.0 mAcm -2 was observed upon back illumination which significantly improved over an ITO-only back contact (5.0 mAcm -2 ). The PCE obtained from back illumination was enhanced when using CuI NPs as the HTL due to the reduced back barrier height, and improved back interface as determined by temperature dependent current vs. voltage characteristics and impedance spectroscopy analysis. The improvement in device performance of the bifacial configuration is a significant step forward toward realizing thin film photovoltaic modules which harvest energy incident on the rear of the module.

36 MATERIALS SCIENCE↗

Isotopic analysis of Nd nanoparticles using single particle MC-ICP-MS: A comparative study with single particle-ICP-TOF-MS

Single particle - inductively coupled plasma - mass spectrometry (SP-ICP-MS) is a powerful technique for characterization of the elemental and isotopic composition of individual particles. In this work, the capabilities of the newest generation of MC-ICP-MS with acquisition rates down to 50 ms were evaluated for single particle analysis, with a focus on isotopic precision achievable on a single-particle level. Nd (NdVO 4 ) nanoparticles (~120 nm in diameter) were used as case study and were first characterized in terms of mass (respective size) and particle number concentration by SP-ICP-TOF-MS and then by SP-MC-ICP-MS for isotopic precision. For the isotopic ratio measurements, the MC-ICP-MS performance was compared to the ICP-TOF-MS and it was found that the isotope ratio precision was increased (R 2 between 0.98 and 0.99) compared to ICP-TOF-MS (R 2 between 0.88 and 0.97). The accuracy attained on a single particle level, was compared to bulk digestion followed by MC-ICP-MS analysis, and the SP-MC-ICP-MS technique was able to determine the particle population average to be <4 %, percent relative differences for the 142 Nd/ 144 Nd, 143 Nd/ 144 Nd, 145 Nd/ 144 Nd, 146 Nd/ 144 Nd, and 148 Nd/ 144 Nd ratios The detection limit for the SP-MC-ICP-MS approach was also assessed. Here, when utilizing an all Faraday-cup based detection scheme the determined LOD for the measurements was 0.2fg for Nd, per particle. Based on these results, the newest generation of MC-ICP-MS has demonstrated its utility for performing SP measurement, particularly when high precision isotopic determination is warranted.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Precision Loading and Delivery of Molecular Cargo by Size-Controlled Coacervation of Gold Nanoparticles Functionalized with Elastin-like Peptides

Thermoresponsive elastin-like peptides (ELPs) have been extensively investigated in biotechnology and medicine, but little attention has been paid to the process by which coacervation causes ELP-decorated particles to aggregate. Here, using gold nanoparticles (AuNPs) functionalized with a cysteine-terminated 96-repeat of the VPGVG sequence (V96-Cys), we show that the size of the clusters that reversibly form above the ELP transition temperature can be finely controlled in the 250 to 930 nm range by specifying the concentration of free V96-Cys in solution and using AuNPs of different sizes. We further find that the localized surface plasmon resonance peak of the embedded AuNPs progressively red-shifts with cluster size, likely due to an increase in particle–particle contacts. We exploit this fine control over size to homogeneously load precise amounts of the dye Nile Red and the antibiotic Tetracycline into clusters of different hydrodynamic diameters and deliver cargos near-quantitatively by deconstructing the aggregates below the ELP transition temperature. Beyond establishing a key role for free ELPs in the agglomeration of ELP-functionalized particles, our results provide a path for the thermally controlled delivery of precise quantities of molecular cargo. This capability might prove useful in combination photothermal therapies and theranostic applications, and to trigger spatially and temporally uniform responses from biological, electronic, or optical systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Efficient Oxidative Decomposition of Jet-Fuel exo -Tetrahydrodicyclopentadiene (JP-10) by Aluminum Nanoparticles in a Catalytic Microreactor: An Online Vacuum Ultraviolet Photoionization Study

The oxidation of gas-phase exo-tetrahydrodicyclopentadiene (JP-10, C 10 H 16 ) over aluminum nanoparticles (AlNP) has been explored between a temperature range of 300 and 1250 K with a novel chemical microreactor. The results are compared with those obtained from chemical microreactor studies of helium-seeded JP-10 and of helium–oxygen-seeded JP-10 without AlNP to gauge the effects of molecular oxygen and AlNP, respectively. Vacuum ultraviolet (VUV) photoionization mass spectrometry reveals that oxidative decomposition of JP-10 in the presence of AlNP is lowered by 350 and 200 K with and without AlNP, respectively, in comparison with pyrolysis of the fuel. Overall, 63 nascent gas-phase products are identified through photoionization efficiency (PIE) curves; these can be categorized as oxygenated molecules and their radicals as well as closed-shell hydrocarbons along with hydrocarbon radicals. Quantitative branching ratios of the products reveal diminishing yields of oxidized species and enhanced branching ratios of hydrocarbon species with the increase in temperature. While in the low-temperature regime (300–1000 K), AlNP solely acts as an efficient heat transfer medium, in the higher-temperature regime (1000–1250 K), chemical reactivity is triggered, facilitating the primary decomposition of the parent JP-10 molecule. Furthermore, this enhanced reactivity of AlNP could plausibly be linked to the exposed reactive surface of the aluminum (Al) core generated upon the rupture of the alumina shell material above the melting point of the metal (Al).

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Effect of TiO x Substrate Interactions on the Electrocatalytic Oxygen Reduction Reaction at Au Nanoparticles

Here, we report a robust model for studying electrocatalytic reactions at metal nanoparticles (NPs) in contact with metal oxide surfaces. The metal oxide layer (TiO x ) is prepared by atomic layer deposition, and it is sufficiently thin that it does not hinder electron transfer from the underlying conductive electrode to the supported AuNP electrocatalysts. In advance of the experiments, density functional theory (DFT) predicted that direct contact between AuNPs and TiO x would lead to enhanced activity for the oxygen reduction reaction (ORR). DFT attributes the observed ORR enhancement to partial charge transfer from oxygen vacancies within the TiO x film to the supported AuNPs and hence formation of anionic Au species. The experimental findings are in near quantitative agreement with the DFT results. Specifically, compared to isolated AuNPs, decreases of ~ 100 and ~ 50 mV in the ORR onset potential are observed experimentally for AuNPs supported on TiO 1.9 and TiO 2.0 films, respectively.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

Complex Fluorine Chemical Potential Effects on the Shape and Compositional Heterogeneity of KTa 1– x Nb x O 3 Nanoparticles

When kinetic conditions dominate and dictate the growth in a nanoparticle synthesis, properties of the synthesis environment can have considerable effects on the properties of the products. Such effects were studied here, where the solution environment was changed via the addition of KF to the hydrothermal syntheses of KTa 1– x Nb x O 3 and KTaO 3 . One result demonstrated the straightforward cause-and-effect relationship between the solution and reaction kinetics: KF directly increased the solution stability of the Ta species and therefore decreased its reaction rate, resulting in a change in composition heterogeneity of Ta and Nb in the KTa 1– x Nb x O 3 particles. However, not all effects are so simple; changing the chemical potential of the solution with KF can also promote the formation of particles with anisotropic defect enhanced kinetic Wulff shapes instead of cuboidal shapes. The increased F chemical potential in the solution enabled the formation of planar defects in the bulk, which accelerated growth in-plane to form particles characterized by flat rectangular flake geometries. In this work, thermodynamic modeling with density functional theory calculations confirmed that sufficient KF concentrations can drive the formation of a defect phase K n +1 Ta n O 3 n F.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗