SEARCH · Engineering Papers

Results for “Mix Testing”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Forward slanted slot throat stability bypass to increase the stable airflow range of a Mach 2.5 inlet with 60 percent internal contraction

The results of an experimental investigation to increase the stable airflow operating range of a supersonic mixed-compression inlet are presented. Two forward-slanted slot stability-bypass entrance configurations were tested. In terms of diffuser-exit corrected airflow, a large inlet stable airflow range of 18.5 percent was obtained with the superior configuration if a constant pressure was maintained in the bypass plenum. Limited unstart angle-of-attack data are presented.

Shaw, R. J.↗

NASA NTRS1975

Design of a very-low-bleed Mach 2.5 mixed-compression inlet with 45 percent internal contraction

A full-scale, mixed-compression inlet was designed for operation with the TF30-P-3 turbofan engine and tested at Mach numbers of 2.5 and 2.0. The two-cone axisymmetric inlet had minimum internal contraction consistent with high total pressure recovery and low cowl drag. At Mach 2.5, inlet recovery was 0.906 with only 0.021 centerbody bleed mass-flow ratio and no cowl bleed. Increased centerbody bleed gave a maximum inlet unstart angle of attack of 6.85 deg. At Mach 2.0, inlet recovery was 0.94 with only 0.014 centerbody bleed mass-flow ratio and no cowl bleed. Inlet performance and angle-of-attack tolerance is presented for operation at Mach numbers of 2.5 and 2.0.

Wasserbauer, J. F.↗

NASA NTRS1979

Full-coverage film cooling: 3-dimensional measurements of turbulence structure and prediction of recovery region hydrodynamics

Hydrodynamic measurements were made with a triaxial hot-wire in the full-coverage region and the recovery region following an array of injection holes inclined downstream, at 30 degrees to the surface. The data were taken under isothermal conditions at ambient temperature and pressure for two blowing ratios: M = 0.9 and M = 0.4. Profiles of the three main velocity components and the six Reynolds stresses were obtained at several spanwise positions at each of the five locations down the test plate. A one-equation model of turbulence (using turbulent kinetic energy with an algebraic mixing length) was used in a two-dimensional computer program to predict the mean velocity and turbulent kinetic energy profiles in the recovery region. A new real-time hotwire scheme was developed to make measurements in the three-dimensional turbulent boundary layer over the full-coverage surface.

Yavuzkurt, S.↗

NASA NTRS1981

A hybrid method for improving MCSCF convergence

It has been found that the convergence problems for many ill conditioned single-configuration SCF calculations arise from mixing among only a small number of orbitals. This orbital set includes the highest closed, the partially filled, and (possibly) a few of the lowest virtual orbitals. The fact that convergence problems can be, in very large measure, linked to a small orbital set is used to design a hybrid MCSCF procedure in which these orbitals are treated using a second-order MCSCF method, while other mixings are treated with a lower-order method which avoids the time consuming integral transformation. Tests on BeO show that the hybrid method yields convergence even when the simple lower-order treatment diverges. The method is expected to facilitate determination of MCSCF wave functions for large basis problems and for the construction of potential energy surfaces.

Bauschlicher, C. W., Jr.↗

NASA NTRS1982

High temperature low cycle fatigue mechanisms for nickel base and a copper base alloy

Damage mechanisms were studied in Rene' 95 and NARloy Z, using optical, scanning and transmission in microscopy. In necklace Rene' 95, crack initiation was mainly associated with cracking of surface MC carbides, except for hold time tests at higher strain ranges where initiation was associated more with a grain boundary mechanism. A mixed mode of propagation with a faceted fracture morphology was typical for all cycle characters. The dependence of life on maximum tensile stress can be demonstrated by the data falling onto three lines corresponding to the three tensile hold times, in the life against maximum tensile stress plot. In NARloy Z, crack initiation was always at the grain boundaries. The mode of crack propagation depended on the cycle character. The life decreased with decreasing strain rate and with tensile holds. In terms of damage mode, different life prediction laws may be applicable to different cycle characters.

Shih, C. I.↗

NASA NTRS1985

Modeling of elastically mounted vertical rotor

The evaluation of the dynamic behavior of a rotating system is possible by means of modal parameters (Eigenvalues and Eigenvectors). A mixed analytical and experimetal approach is used to identify the modal parameters of a specially designed test rig. The modal identification is done both for nonrotating as well as rotating systems. These modal parameters are used to validate a developed Finite Element Model.

Dana, S. S.↗

NASA NTRS1986

Composite interlaminar fracture toughness: Three-dimensional finite element modeling for mixed mode 1, 2 and 3 fracture

A computational method/procedure is described which can be used to simulate individual and mixed mode interlaminar fracture progression in fiber composite laminates. Different combinations of Modes 1, 2, and 3 fracture are simulated by varying the crack location through the specimen thickness and by selecting appropriate unsymmetric laminate configurations. The contribution of each fracture mode to strain energy release rate is determined by the local crack closure methods while the mixed mode is determined by global variables. The strain energy release rates are plotted versus extending crack length, where slow crack growth, stable crack growth, and rapid crack growth regions are easily identified. Graphical results are presented to illustrate the effectiveness and versatility of the computational simulation for: (1) evaluating mixed-mode interlaminar fracture, (2) for identifying respective dominant parameters, and (3) for selecting possible simple test methods.

Murthy, P. L. N.↗

NASA NTRS1988

Composite interlaminar fracture toughness - Three-dimensional finite-element modeling for mixed mode I, II, and fracture

Murthy, Pappu L. N.↗

NASA NTRS1990

Carbon deposition model for oxygen-hydrocarbon combustion. Task 6: Data analysis and formulation of an empirical model

The formation and deposition of carbon (soot) was studied in the Carbon Deposition Model for Oxygen-Hydrocarbon Combustion Program. An empirical, 1-D model for predicting soot formation and deposition in LO2/hydrocarbon gas generators/preburners was derived. The experimental data required to anchor the model were identified and a test program to obtain the data was defined. In support of the model development, cold flow mixing experiments using a high injection density injector were performed. The purpose of this investigation was to advance the state-of-the-art in LO2/hydrocarbon gas generator design by developing a reliable engineering model of gas generator operation. The model was formulated to account for the influences of fluid dynamics, chemical kinetics, and gas generator hardware design on soot formation and deposition.

Makel, Darby B.↗

NASA NTRS1991

Laser induced spark ignition of methane-oxygen mixtures

The use of laser-induced spark ignition in liquid-propellant rocket engines is investigated by studying the ignition of mixtures of methane and oxygen. Specific attention is given to minimum ignition energy, spark efficiency, the effect of ignition energy on flame kernels, the effect of laser wavelength, and comparisons with electrode-spark ignition. A pulsed frequency-doubled Nd:YAG laser is tested at atmospheric pressure and 296 K under both laminar-premixed and turbulent-incompletely-mixed conditions. Laser sparks of 10 and 40 mJ and an electrode spark of 6 mJ are measured for flame-kernel radius as a function of time with pulsed laser shadowgraphy. Initially, the flame-kernel size is similar to those predicted by the Taylor spherical-blast-wave model, and subsequent growth is characterized by rapid acceleration. The growth rate is significantly affected by the effect of incomplete fuel-oxidizer mixing.

Lee, T. W.↗

NASA NTRS1993

A normal stress subgrid-scale eddy viscosity model in large eddy simulation

The Smagorinsky subgrid-scale eddy viscosity model (SGS-EVM) is commonly used in large eddy simulations (LES) to represent the effects of the unresolved scales on the resolved scales. This model is known to be limited because its constant must be optimized in different flows, and it must be modified with a damping function to account for near-wall effects. The recent dynamic model is designed to overcome these limitations but is compositionally intensive as compared to the traditional SGS-EVM. In a recent study using direct numerical simulation data, Horiuti has shown that these drawbacks are due mainly to the use of an improper velocity scale in the SGS-EVM. He also proposed the use of the subgrid-scale normal stress as a new velocity scale that was inspired by a high-order anisotropic representation model. The testing of Horiuti, however, was conducted using DNS data from a low Reynolds number channel flow simulation. It was felt that further testing at higher Reynolds numbers and also using different flows (other than wall-bounded shear flows) were necessary steps needed to establish the validity of the new model. This is the primary motivation of the present study. The objective is to test the new model using DNS databases of high Reynolds number channel and fully developed turbulent mixing layer flows. The use of both channel (wall-bounded) and mixing layer flows is important for the development of accurate LES models because these two flows encompass many characteristic features of complex turbulent flows.

Horiuti, K.↗

NASA NTRS1996

Verification of Orthogrid Finite Element Modeling Techniques

The stress analysis of orthogrid structures, specifically with I-beam sections, is regularly performed using finite elements. Various modeling techniques are often used to simplify the modeling process but still adequately capture the actual hardware behavior. The accuracy of such 'Oshort cutso' is sometimes in question. This report compares three modeling techniques to actual test results from a loaded orthogrid panel. The finite element models include a beam, shell, and mixed beam and shell element model. Results show that the shell element model performs the best, but that the simpler beam and beam and shell element models provide reasonable to conservative results for a stress analysis. When deflection and stiffness is critical, it is important to capture the effect of the orthogrid nodes in the model.

Steeve, B. E.↗

NASA NTRS1961

Preliminary Investigation of an Underwater Ramjet Powered by Compressed Air

Part I contains the results of a preliminary experimental investigation of a particular design of an underwater ramjet or hydroduct powered by compressed air. The hydroduct is a propulsion device in which the energy of an expanding gas imparts additional momentum to a stream of water through mixing. The hydroduct model had a fineness ratio of 5.9, a maximum diameter of 3.2 inches, and a ratio of inlet area to frontal area of 0.32. The model was towed at a depth of 1 inch at forward speeds between 20 and 60 feet per second for airflow rates from 0.1 to 0.3 pound per second. Longitudinal force and pressures at the inlet and in the mixing chamber were determined. The hydroduct produced a positive thrust-minus-drag force at every test speed. The force and pressure coefficients were functions primarily of the ratio of weight airflow to free-stream velocity. The maximum propulsive efficiency based on the net internal thrust and an isothermal expansion of the air was approximately 53 percent at a thrust coefficient of 0.10. The performance of the test model may have been influenced by choking of the exit flow. Part II is a theoretical development of an underwater ramjet using air as "fuel." The basic assumption of the theoretical analysis is that a mixture of water and air can be treated as a compressible gas. More information on the properties of air-water mixtures is required to confirm this assumption or to suggest another approach. A method is suggested from which a more complete theoretical development, with the effects of choking included, may be obtained. An exploratory computation, in which this suggested method was used, indicated that the effect of choked flow on the thrust coefficient was minor.

Mottard, Elmo J.↗

NASA NTRS2000

Mixing, Noise and Thrust Benefits Using Corrugated Designs

These projects are directed toward the analysis of several concepts for nozzle and inlet performance improvement and noise reduction from jet exhausts. Currently. The FM&AL also initiates new joint research between the HU/FM&AL, the Hyper-X Program Team at the LaRC, and the Central Institute of Aviation Motors (CIAM), Moscow, Russia in the field of optimization of fuel injection and mixing in air-breathing propulsion systems. The main results of theoretical, numerical simulation and experimental tests obtained in the previous research are in the papers and patents. The goals of the 14U/FM&AL programs are twofold: 1) to improve the working efficiency of the HU/FM&AL team in generating new innovative ideas and in conducting research in the field of fluid dynamics and acoustics, basically for improvement of supersonic and subsonic aircraft engines, and 2) to attract promising minority students to this research and training and, in cooperation with other HU departments, to teach them basic knowledge in Aerodynamics, Gas Dynamics, and Theoretical and Experimental Methods in Aeroacoustics and Computational Fluid Dynamics (CFD). The research at the HU/FM&AL supports reduction schemes associated with the emission of en 'ne pollutants for commercial aircraft and concepts for reduction of 91 observables for military aircraft. These research endeavors relate to the goals of the NASA Strategic Enterprise in Aeronautics concerning the development of environmentally acceptable aircraft. It is in this precise area, where the US aircraft industry, academia, and Government are in great need of trained professionals and which is a high priority goal of the Minority University Research and Education (MLTREP) Program, that the HU/FM&AL can make its most important contribution.

Morgan, Morris H., III↗

NASA NTRS2005

High-Flux, High Performance H2O2 Catalyst Bed for ISTAR

On NASA's ISTAR RBCC program packaging and performance requirements exceeded traditional H2O2 catalyst bed capabilities. Aerojet refined a high performance, monolithic 90% H202 catalyst bed previously developed and demonstrated. This approach to catalyst bed design and fabrication was an enabling technology to the ISTAR tri-fluid engine. The catalyst bed demonstrated 55 starts at throughputs greater than 0.60 lbm/s/sq in for a duration of over 900 seconds in a physical envelope approximately 114 of traditional designs. The catalyst bed uses photoetched plates of metal bonded into a single piece monolithic structure. The precise control of the geometry and complete mixing results in repeatable, quick starting, high performing catalyst bed. Three different beds were designed and tested, with the best performing bed used for tri-fluid engine testing.

Ponzo, J.↗

NASA NTRS2022

Trash-to-Gas: Trash Preparation and Feed Mechanism

One method of reducing the mass and volume of astronaut waste items during future exploration missions is a process called Trash-to-Gas (TtG), which uses thermal degradation to convert various astronaut waste items into a gas that can either be repurposed onboard or safely vented overboard. This project aims to determine which methods for pre-processing waste may enhance the gasification efficiency within a microgravity TtG reactor. Preparation methods that were investigated include mixing, pre-drying, shredding, compacting, and raw unprocessed waste. Each of these preparation methods was tested within the state-of-the-art subscale TtG system, known as the Orbital Syngas/Commodity Augmentation Reactor (OSCAR), and the resulting solid-to-gas conversion and burn durations were compared. Full-scale CAD models of these various preparation methods in conjunction with a projected full-scale TtG reactor were created using Creo Parametric. An Equivalent System Mass (ESM) analysis was then performed to trade the benefits of improved solid-to-gas performance with the costs associated with implementing the additional components that would increase system mass, power, volume, and design complexity. The results of this ESM analysis will be leveraged for future full-scale TtG system development to help reduce the overall mass, power, and volume of the system while ensuring effective reactor performance.

Ray Pitts↗

NASA NTRS1982

A high-resolution model of the planetary boundary layer - Sensitivity tests and comparisons with SESAME-79 data

A one-dimensional, planetary boundary layer (PBL) model is presented and verified using April 10, 1979 SESAME data. The model contains two modules to account for two different regimes of turbulent mixing. Separate parameterizations are made for stable and unstable conditions, with a predictive slab model for surface temperature. Atmospheric variables in the surface layer are calculated with a prognostic model, with moisture included in the coupled surface/PBL modeling. Sensitivity tests are performed for factors such as moisture availability, albedo, surface roughness, and thermal capacity, and a 24 hr simulation is summarized for day and night conditions. The comparison with the SESAME data comprises three hour intervals, using a time-dependent geostrophic wind. Close correlations were found with daytime conditions, but not in nighttime thermal structure, while the turbulence was faithfully predicted. Both geostrophic flow and surface characteristics were shown to have significant effects on the model predictions

Zhang, D.↗

NASA NTRS2009

Amorphous Silk Fibroin Membranes for Separation of CO2

Amorphous silk fibroin has shown promise as a polymeric material derivable from natural sources for making membranes for use in removing CO2 from mixed-gas streams. For most applications of silk fibroin, for purposes other than gas separation, this material is used in its highly crystalline, nearly natural form because this form has uncommonly high tensile strength. However, the crystalline phase of silk fibroin is impermeable, making it necessary to convert the material to amorphous form to obtain the high permeability needed for gas separation. Accordingly, one aspect of the present development is a process for generating amorphous silk fibroin by treating native silk fibroin in an aqueous methanol/salt solution. The resulting material remains self-standing and can be prepared as thin film suitable for permeation testing. The permeability of this material by pure CO2 has been found to be highly improved, and its mixed-gas permeability has been found to exceed the mixed-gas permeabilities of several ultrahigh-CO2-permeable synthetic polymers. Only one of the synthetic polymers poly(trimethylsilylpropyne) [PTMSP] may be more highly permeable by CO2. PTMSP becomes unstable with time, whereas amorphous silk should not, although at the time of this reporting this has not been conclusively proven.

Aberg, Christopher M.↗