Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Microstructural properties”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Microstructure and Corrosion Properties of Laser-Welded SAF 2507 Super Duplex Stainless Steel Joints

SAF 2507 super duplex stainless steel has been welded using laser beam (LB) welding and laser/gas metal arc hybrid (LGH) welding processes. The pitting and intergranular corrosion properties of the welding joints have been tested using electrochemical testing and microstructure observations. The volume fraction of the ferrite phase reaches 70% in the weld zone of the LB welding joint, while the volume fraction of the ferrite phase is 60% for the welding joint of LGH due to the introduction of Ni from welding wire. The pitting corrosion resistance of the welding joint for LB is better than that of LGH. The pitting corrosion is easily conceived in the heat-affected zone (HAZ) because of the formation of Cr{sub 2}N in the HAZ during welding.

36 MATERIALS SCIENCE↗

Effects of size reduction on microstructural, optical, vibrational, magnetic and photocatalytic properties of ZnO nanocrystals

Highlights: • ZnO nanocrystals of different sizes 4–19 nm, thus different S/V ratios synthesized. • Lattice strain and lattice volume increase with size reduction. • Raman spectra show enhanced surface effects with phonon mode disappearance. • ESR shows exchange interaction; VSM shows surface originated ferromagnetism. • Photocatalysis is less affected with size reduction and surface enhancement. - Abstract: ZnO nanocrystals were synthesized in the size range 4 nm–19 nm by chemical co-precipitation method and extensively characterized by various techniques. Size control was achieved by changing the concentration of ME that acted as the capping agent. Lattice strain and lattice volume were found to increase with the decrease in crystallite size that could be attributed to an enhanced influence of surface atoms. Raman spectroscopy provided evidence of enhancement of surface influence and reduction of crystallinity with the observation of decrease in E{sub 2}{sup high} phonon mode intensity with a decrease in crystallite size. Electron spin resonance spectra revealed the presence of exchange interaction as well as presence of lattice disorder. Vibrating sample magnetometry results showed that M-H curves exhibit hysteresis loops which confirmed the ferromagnetic nature of the nanocrystals and it could be attributed to the interaction between localized electron spins resulting from oxygen vacancies at the surface. Blue shift of the UV–Visible absorption spectra was observed with decrease in crystallite size, which could be attributed to quantum confinement effect. Room temperature photoluminescence spectra were recorded under UV light excitation, which showed emission of different colours (light violet, violet, blue and green) in the visible region, attributable to the presence of various types of defects such as zinc interstitial, zinc vacancy and oxygen vacancy in the ZnO nanocrystals. Photodegradation of aqueous methylene blue by the ZnO nanocrystals was performed under simulated sunlight irradiation. There was a very small increase in efficiency of photodegradation with size reduction, which showed that there was no significant change in surface defects with size reduction in the nanocrystals despite the surface enhancement. A mechanism for photocatalysis involving defect states has been proposed.

77 NANOSCIENCE AND NANOTECHNOLOGY↗

Microstructure factor and mechanical and electronic properties of hydrogenated amorphous and nanocrystalline silicon thin-films for microelectromechanical systems applications

Thin-film silicon allows the fabrication of MEMS devices at low processing temperatures, compatible with monolithic integration in advanced electronic circuits, on large-area, low-cost, and flexible substrates. The most relevant thin-film properties for applications as MEMS structural layers are the deposition rate, electrical conductivity, and mechanical stress. In this work, n{sup +}-type doped hydrogenated amorphous and nanocrystalline silicon thin-films were deposited by RF-PECVD, and the influence of the hydrogen dilution in the reactive mixture, the RF-power coupled to the plasma, the substrate temperature, and the deposition pressure on the structural, electrical, and mechanical properties of the films was studied. Three different types of silicon films were identified, corresponding to three internal structures: (i) porous amorphous silicon, deposited at high rates and presenting tensile mechanical stress and low electrical conductivity, (ii) dense amorphous silicon, deposited at intermediate rates and presenting compressive mechanical stress and higher values of electrical conductivity, and (iii) nanocrystalline silicon, deposited at very low rates and presenting the highest compressive mechanical stress and electrical conductivity. These results show the combinations of electromechanical material properties available in silicon thin-films and thus allow the optimized selection of a thin silicon film for a given MEMS application. Four representative silicon thin-films were chosen to be used as structural material of electrostatically actuated MEMS microresonators fabricated by surface micromachining. The effect of the mechanical stress of the structural layer was observed to have a great impact on the device resonance frequency, quality factor, and actuation force.

36 MATERIALS SCIENCE↗

Effects of Varying Composition and Kinetics on the Microstructural and Mechanical Properties of Polysiloxane Foams

Polysiloxane elastomers are used in a wide variety of applications including medicine, aerospace, and defense industries. Though these materials demonstrate many useful properties such as flexibility, resistance to chemical attack, electrical insulation, and biocompatibility, the mechanical properties and product integrity are sensitive and may degrade in harsh environments. Understanding the degradation mechanisms and their effects on the mechanical properties of foamed polysiloxanes has been the subject of many studies; however, current formulations still produce foams with poor mechanical and aging properties. The chemical complexity, environmental sensitivity, and multitude of synthesis and degradation reactions that continuously occur complicate predicting the physical and mechanical properties or aging behavior. These factors warrant continued investigations on the chemistry, microstructural characterizations, and aging behavior of these materials

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Three-Layer TIG-Welded 2219 Aluminum Alloys with Dissimilar Heat Treatments

2219-C10S and 2219-CYS aluminum alloys are 2219 aluminum alloys with different heat treatment processes, and they have been widely used in the aerospace industry. In the present study, 2219-C10S and 2219-CYS aluminum alloys were butt-welded by three-layer tungsten inert gas arc welding (with the welding center of the third layer shifted toward the CYS side), and the microstructure characteristics and mechanical properties of the welded joint were investigated. The lamellar θ′ phases, the bulk or rod θ phases, and the coarse rod-shaped or pancake-shaped Al-Cu-Fe-Mn phases coexisted in the two aluminum alloys. The Cu content of the α-Al matrix and the distribution of eutectic structures of different welding layers in the weld zone (WZ) were varied, implying that the segregation degrees of the Cu element were different due to the different welding thermal cycles in different welding layers. The microhardness values of the CYS side were much higher than those of the C10S side in each region on both sides of the joint. The tensile test deformation was concentrated mainly in the regions of WZ and the over aged zone (OAZ), where the microhardness values were relatively low. The main deformation concentrated region was transferred from the CYS side to the C10S side with the increase in the tensile load during the tensile test. The fracture behavior of the tensile test showed that the macroscopic crack initiated near the front weld toe had gone through the crack blunt region, the shear fracture region of the partially melted zone (PMZ), and the shear fracture region of OAZ. Meanwhile, the fracture characteristics gradually evolved from brittle to ductile. The concentrated stress and the dense eutectic structure in the region near the front weld toe of the C10S side contributed to the fracture of the joint. The shift of the welding center of the third layer to the CYS side resulted in two effects: (i) the microhardness values from the middle layer to the top layer in the PMZ of the CYS side were the most significantly increased and (ii) the distance between the front weld toe and the fusion line of the CYS side was significantly larger.

36 MATERIALS SCIENCE↗

Effects of Thermal Exposure on the Microstructure and Mechanical Properties of Al-Si-Cu-Ni-Mg-Gd Alloy

The present study focused on the effect of thermal exposure on the phase evolution and properties of the cast-T6 Al-12Si-4Cu-2Ni-0.8Mg-xGd (x = 0, 0.1, and 0.2) alloy used for cast piston.The thermal stability of the alloys was studied in the temperature range of 200-300 °C for exposure duration up to 500 h, thus obtaining the relationship between the microstructural evolution and its impact on the mechanical properties. The fine Al{sub 2}Cu phase grew into the coarse θ-Al{sub 2}Cu phases during the thermal exposure, resulting in a decrease in the mechanical strength of the alloy. The thermal stability and stiffness of the Al-Si-Cu-Ni-Mg alloys were improved with the increase in Gd content from 0 to 0.2%.

36 MATERIALS SCIENCE↗

Magnetic microstructure and magnetic properties of uniaxial itinerant ferromagnet Fe 3 GeTe 2

Here, magnetic force microscopy was used to observe the magnetic microstructure of Fe 3 GeTe 2 at 4 K on the (001) surface. The surface magnetic structure consists of a two-phase domain branching pattern that is characteristic for highly uniaxial magnets in the plane perpendicular to the magnetic easy axis. The average surface magnetic domain width D s = 1.3 μm determined from this pattern, in combination with intrinsic properties calculated from bulk magnetization data (the saturation magnetization M s = 376 emu/cm 3 and the uniaxial magnetocrystalline anisotropy constant K u = 1.46 × 10 7 erg/cm 3 ), was used to determine the following micromagnetic parameters for Fe 3 GeTe 2 from phenomenological models: the domain wall energy γ w = 4.7 erg/cm 2 , the domain wall thickness δ w = 2.5 nm, the exchange stiffness constant A ex = 0.95 × 10 –7 erg/cm, the exchange length l ex = 2.3 nm, and the critical single domain particle diameter d c = 470 nm.

36 MATERIALS SCIENCE↗

The mechanism of magnetic properties improvement and microstructure refinement of Zr in Nd[subscript 2]Fe[subscript 14]B

In order to understand the role of Zr addition in Nd{sub 2}Fe{sub 14}B (2-14-1), a systematic study of Zr in Nd{sub 2}Fe{sub 14}B was done on a series of stoichiometric samples (Nd{sub 1-x}Zr{sub x}){sub 2}Fe{sub 14}B with 0 {le} x {le} 0.16. As-cast ingots formed significant amounts of Nd{sub 2}Fe{sub 17} starting at x = 0.06, while in the melt-spun ribbons, no Nd{sub 2}Fe{sub 17} was observed for the range studied. A monotonic decrease in lattice parameters for the 2-14-1 phase indicate Zr solubility in the melt-spun ribbons, but this is not observed in the ingots. Magnetic and thermal measurements on the ribbons showed that the saturated magnetization Ms (around 16 kG), the spin reorientation temperature (125 K), and the Curie temperature (583 K) do not depend on the Zr content, while the anisotropy field Ha slightly decreased as the Zr content increased. The energy product (BHmax) and the coercive force H{sub c} are highly dependent on the solidification and annealing process. Scanning electron microscopy and transmission electron microscopy on the as-melt spun alloys are consistent with x-ray diffraction showing Zr solubility in the 2-14-1 grains. After annealing, Zr diffuses to the grain boundaries to form Zr enriched compounds. Thus, while Zr may exhibit a metastable solubility in Nd{sub 2}Fe{sub 14}B, the enhanced magnetic behaviors observed in melt-spun ribbons are due to the refinement of the microstructure and enhanced grain-boundary pinning.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Electric field enhanced diffusion welding of alloy 617: Microstructural characteristics and mechanical properties

This study investigated the microstructural characteristics and mechanical behavior of diffusion welded nickel-based Alloy 617 obtained by electric field-assisted sintering (EFAS) using various parameters. The interfacial microstructure exhibited different characteristics including good grain boundary (GB) migration across the interface in the samples diffusion-welded at 1100 °C and a flat interface in the samples joined at 1000 °C and 1050 °C. The interface consisted of fine Al 2 O 3 oxides, while precipitation of interfacial M 23 C 6 carbides was not observed. Grain boundaries migrated across the Al 2 O 3 oxides, leaving these oxides within the grains. Graded grain size was observed, with grain coarsening being more significant near the sample surface due to the temperature gradient induced by EFAS. Tensile testing revealed that the specimens fractured in the matrix away from the interface, indicting strong diffusion-welded joints. Further, the peak tensile strength of 807 MPa was obtained in the samples welded at 1000 °C due to minimal grain growth. The materials obtained at 1100 °C exhibited reduced tensile strength but improved ductility. Strain maps revealed by digital image correlation showed alternating high and low strain segments in the samples produced at 1000 °C and 1050 °C, indicating that the flat interfaces with no GB migration were less ductile compared to the matrix. A greater strain uniformity was observed along the bond interfaces with improved GB migration. The hardness reduced near the sample surfaces due to enlarged grains induced by temperature gradient. This study demonstrates that GB migration and enhanced mechanical strength can be achieved in diffusion-welded Alloy 617.

36 MATERIALS SCIENCE↗

Effects of Solidification Cooling Rates on Microstructures and Physical Properties of Fe-6.5%Si Alloys

Compared to the widely used Fe-3.2wt%Si steel, Fe-6.5wt%Si has superior electric and magnetic properties, including higher electrical resistivity, lower iron loss, higher permeability, and near zero magnetostriction. However, Fe-6.5wt%Si sheet is difficult to produce using traditional manufacturing processes as the high silicon content favors the formation of ordered phases that embrittle the material. Fortunately, these ordered phases can be suppressed if the alloy is cooled fast enough from a high temperature kinetically trapping the disordered solid solution or amorphous state. Planar flow casting is known for its rapid solidification rate. In order to consider it as a viable method to manufacture ductile Fe-6.5wt%Si sheets, the effect of cooling rate on physical properties of Fe-6.5wt%Si alloy are systematically investigated. In this work, various cooling rates are achieved by changing melt-spin wheel speeds, which significantly affect the solidification temperature profile and have profound effects on ordering, microstructures, textures, hardness, and magnetic properties. High cooling rates result in refined grains, reduced ordering, enhanced <100> out of the plane texture, decreased hardness, and increased coercivity. This study demonstrates a critical cooling rate at ~1.7 × 10 5 K/s, corresponding to a tangential wheel speed of 5-7 m/s, below which the hardness significantly increases in agreement with the sudden increase of the ordered phases that causes the material embrittlement.

36 MATERIALS SCIENCE↗

Microstructure and creep properties of cast near-eutectic Al–Ce–Ni alloys

This study investigates the as-cast and aged microstructures, thermal stability, ambient temperature strengthening, and creep resistance of three ternary Al–Ce–Ni alloys (wt%): near-eutectic Al–10Ce–5Ni (with both eutectic and hypoeutectic regions), hypoeutectic Al-7.5Ce-3.75Ni (with numerous primary Al dendrites), and hypereutectic Al-12.5Ce-6.25Ni (with coarse, blocky primary Al3Ni and Al11Ce3 precipitates and some primary Al dendrites). Depending on the alloy composition and local solidification conditions, the following eutectic morphologies are found: (i) coarse Al–Ce eutectic colonies where Al 11 Ce 3 is in the form of “Chinese script”, (ii) intermingled regions of binary Al–Ce and Al–Ni eutectic colonies, with finer Al 3 Ni and Al 11 Ce 3 fibers, (iii) large ternary eutectic colonies, where the binary Al 3 Ni and Al 11 Ce 3 phases are alternating or intertwining within the individual, fine fibers (diameters of ~60–170 nm, depending on solidification rates), and (iv) ternary eutectic zones (between primary Al dendrites), where fine Al 3 Ni and Al 11 Ce 3 build up a 3D-interconnected network. The high volume fraction of intermetallic phases and extremely fine eutectic spacing/fiber diameter both contribute to high ambient strengthening (higher as-cast microhardness than binary Al–Ce or Al–Ni), and also provide enhanced creep resistance at 300 and 350 °C. Additionally, the alloys are coarsening-resistant up to 425 °C for extended periods, with a gradual decrease in microhardness. The alloys aged at 400 °C to 1050 h show fiber fragmentation and coarsening of the resulting particles, with the faster-diffusing Ni driving more rapid coarsening of the Al 3 Ni particles which engulf finer, more stable Al 11 Ce 3 particles. Severe overaging (performed at 590 °C for 24 h) leads to Al 3 Ni and Al 11 Ce 3 spheroids which remain submicron-sized in eutectic colonies, but micron-sized at colony boundary and at Al dendrite-eutectic interface. Creep resistance at 300 °C of overaged Al–10Ce–5Ni remains substantial, consistent with load-transfer based composite strengthening being an important strengthening mechanism in these alloys, making them excellent candidates for replacement of heavier steel or titanium parts operating under stress up to 300 °C.

36 MATERIALS SCIENCE↗

In situ laser-based resonant ultrasound measurements of microstructure mediated mechanical property evolution

In situ laser-based resonant ultrasound spectroscopy is used to characterize the development of a recrystallized microstructure in a high purity copper sample. The modal shapes, used for mode identification, of several resonant modes are determined before and after annealing by raster scanning the laser interferometric probe. This information is used to isolate the motion of individual modes during high temperature annealing. The evolution of a particular mode during annealing is examined in detail. During recrystallization, the center frequency of this mode shifts by approximately 20% of the original value. Using electron backscatter data it is shown that the majority of this shift is due to changes in the polycrystal average elastic stiffness tensor, driven by changes in texture, and that changes in dislocation density and pinning length are secondary influences.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Microstructural and optical properties of nanocrystalline ZnO deposited onto vertically aligned carbon nanotubes by physical vapor deposition

Nanocrystalline ZnO films with thicknesses of 5 nm, 10 nm, 20 nm, and 50 nm were deposited via magnetron sputtering onto the surface of vertically aligned multi-walled carbon nanotubes (MWCNTs). The ZnO/CNTs heterostructures were characterized by scanning electron microscopy, high resolution transmission electron microscopy, and X-ray diffraction studies. No structural degradation of the CNTs was observed and photoluminescence (PL) measurements of the nanostructured ZnO layers show that the optical properties of these films are typical of ZnO deposited at low temperatures. The results indicate that magnetron sputtering is a viable technique for growing heterostructures and depositing functional layers onto CNTs.

36 MATERIALS SCIENCE↗

Fabrication, microstructure and mechanical properties of W-NiTi composites

Here, new two-phase tungsten-based composites containing 88 wt% tungsten powders and 12 wt% nearly equiatomic NiTi alloy deforming by martensite variant detwinning were fabricated by infiltration and hot pressing in this study. The change of Ti/Ni ratio in NiTi mater alloy and the effect of addition of Nb element on the microstructure, martensitic transformation and mechanical properties of W-NiTi composites were investigated by comparison of W-Ni 50 Ti 50 , W-Ni 44 Ti 56 , W-Ni 42 Ti 58 and W-Ni 42 Ti 53 Nb 5 composites. The results showed that brittle Ni 3 Ti formed in the W-Ni 50 Ti 50 and W-Ni 44 Ti 56 composites and brittle Ti 2 Ni formed in the W-Ni 42 Ti 58 composites while no brittle intermetallics formed in the W-Ni 42 Ti 53 Nb 5 composite. The W-Ni 42 Ti 53 Nb 5 composite exhibited the sharpest martensitic transformation with the largest transformation enthalpy among the four different composites. The W-Ni 42 Ti 53 Nb 5 composite exhibited a double-yielding phenomenon under compression with an ultimate compressive strength of 3820 MPa and a deformation of 50.4%. In-situ synchrotron high-energy Xray diffraction measurements revealed the first yielding was caused by the martensite reorientation of the NiTi matrix and the second was due to the commencement of massive plastic deformation of the reoriented martensite and is also attributed to the microscopic internal fracturing of the W particles.

36 MATERIALS SCIENCE↗

Effects of rare earth ionic doping on microstructures and electrical properties of CaCu{sub 3}Ti{sub 4}O{sub 12} ceramics

Graphical abstract: The dielectric constant decreases monotonically with reduced RE doping ion radius and is more frequency independent compared with that of pure CCTO sample. - Highlights: • The mean grain sizes decrease monotonically with reduced RE doping ionic radius. • Doping gives rise to the monotonic decrease of ϵ{sub r} with reduced RE ionic radius. • The nonlinear coefficient and breakdown field increase with RE ionic doping. • α of all the samples is associated with the potential barrier width rather than Φ{sub b}. - Abstract: Ca{sub 1–x}R{sub x}Cu{sub 3}Ti{sub 4}O{sub 12}(R = La, Nd, Eu, Gd, Er; x = 0 and 0.005) ceramics were prepared by the conventional solid-state method. The influences of rare earth (RE) ion doping on the microstructure, dielectric and electrical properties of CaCu{sub 3}Ti{sub 4}O{sub 12} (CCTO) ceramics were investigated systematically. Single-phase formation is confirmed by XRD analyses. The mean grain size decreases monotonically with reduced RE ion radius. The EDS results reveal that RE ionic doping reduces Cu-rich phase segregation at the grain boundaries (GBs). Doping gives rise to the monotonic decrease of dielectric constant with reduced RE ionic radius but significantly improves stability with frequency. The lower dielectric loss of doped samples is obtained due to the increase of GB resistance. In addition, the nonlinear coefficient and breakdown field increase with RE ionic doping. Both the fine grains and the enhancement of potential barrier at GBs are responsible for the improvement of the nonlinear current–voltage properties in doped CCTO samples.

36 MATERIALS SCIENCE↗

Microstructure and Mechanical Properties of Low-Activation Fe-Cr-V Multicomponent Single-Phase Alloys

A ternary equiatomic and nearly equiatomic alloy composed of the low-activation elements Fe, Cr, and V was designed for potential application as low-activation structural materials for the first wall of fusion reactors. The optimal composition of the multicomponent alloy was determined by minimizing the Gibbs free energy for solid-solution formation. The microstructure, phase stability, and mechanical properties of the equiatomic and optimized Fe-Cr-V alloys were studied. The equiatomic alloy consisted of a body-centered-cubic (BCC) solid-solution phase with a small amount of a face-centered-cubic (FCC) solid-solution phase, whereas the optimized alloy consisted of a single BCC solid-solution phase in the as-cast state. The crystal grains of both alloys were equiaxial. No phase transition was observed in the optimized alloy after homogenization; however, for the equiatomic alloy, the FCC solid-solution phase disappeared and surface relief was observed. The Vickers microhardness and yield strength of the Fe-Cr-V alloys increased after homogenization compared with those of the as-cast alloys.

36 MATERIALS SCIENCE↗

Effect of Cold Rolling and Heat Treatment on Microstructure and Mechanical Properties of Ti-4Al-1Mn Titanium Alloy

Mechanical behavior of Ti-4Al-1Mn titanium alloy has been studied in annealed, cold-rolled and heat-treated conditions. Room temperature tensile strength as well as % elongation has been found to be low with increasing amount of cold rolling. Lowering of strength in cold worked condition is attributed to premature failure. However, the same has been mitigated after heat treatment. Significant effect of cooling media (air and water) from heat treatment temperature on microstructure was not found except for the degree of fineness of α plates. Optimum properties (strength as well as ductility) were exhibited by samples subjected to 15% cold rolling and heat treatment below β transus temperature, which can be attributed to presence of recrystallized microstructure. In cold worked condition, the microstructure shows fine fragmented α plates/Widmanstätten morphology with high dislocation density along with a large amount of strain fields and twinning, which gets transformed to recrystallized equiaxed microstructure and with plate-like morphology after near β heat treatment. Prior cold work is found to have a significant effect on mechanical properties supported by evolution of microstructure. Twinning is found to be assisting in deformation as well as in recrystallization through the formation of deformation and annealing twins during cold working and heat treatment. Fracture analysis of the tested sample with prior cold work and heat-treated condition revealed quasi-ductile failure as compared to only ductile failure features seen for samples heat treated without prior cold work.

36 MATERIALS SCIENCE↗