Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “GRINDING”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

X-Ray Fluorescence Quantitative and Qualitative Analysis Using Micro Glass Beads

The fused glass bead method is the accepted 'best practice' method of preparation of samples for X-ray fluorescence (XRF) analysis. It minimizes the effects of sample heterogeneity and simplifies calibration by dissolving the sample into a uniform glass matrix. Glass fusion XRF samples are typically prepared by grinding sample powder with Lithium Tetraborate / Lithium Bromide and fusing the mixture at 1000 deg. C. In most cases sample-to-flux ratios of between 1:1 to 1:10 are used (1:1 for determination of trace elements and 1:10 for major elements). Typical sample mass consumed is in the range of 1000 to 2500 mg. It would be advantageous to reduce this sample mass in cases where the sample material is rare, valuable or highly radioactive. This study examines the effects of using lower sample-to-flux ratios and smaller fusion bead size on the detection and quantification of major and trace elements by XRF analysis. We have employed a micro fused glass bead process, using sample-to-flux ratios of 1:10, 1:15 and 1:25, to determine the effects on measurement precision, accuracy and detection limit. Objectives: - Created micro fused glass beads of a series of standards and andesite sample with sample-to-flux ratios of 1:10, 1:15 and 1:25. - Perform an qualitative analysis of the different sample-to-flux ratio micro beads and compare the results with the 1:5.3 beads routinely used at SRNL. - Quantitate the major components in the different sample-to-flux ratio micro beads using a wavelength dispersive x-ray fluorescence instrument. Advantages: - Reduce sample amount needed. - Speed up waste tank characterization. - Reduce personnel exposure. - Potential sealed source. Fused micro glass beads with sample-to-flux ratios of 1:10, 1:15 and 1:25 were created using sample amounts of 123 mg, 82 mg and 52 mg respectively. It was possible to detect most of the major oxides and some trace elements in the fused micro glass beads with different sample-to-flux ratios. The quantitative analysis showed good linear correlation between the intensity of the analysis and the concentration of the elements. Good precision and accuracy results were obtained for the majority of the major oxides in the three fused micro glass beads with different sample-to-flux ratios. Path Forward: Enhance the precision and accuracy of the method by optimizing different sample preparation steps, such as weighing and sample transfer. Continue to increase the sample-to-flux ratio to determine the minimum amount of sample needed to perform a multielement analysis. Consider the use of synthetic standards to lower the detection limit of the analysis. Used the micro bead sample preparation method to analyze radioactive samples.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

In-Can Incineration and Vitrification Process for the Treatment of Transuranic Wastes - 20035

Technological alpha contaminated wastes are produced by the nuclear fuel cycle management industry, essentially from MOX fuel production units. These Plutonium Contaminated Materials (PCM) contain a mixture of organic, metal and mineral materials, contaminated with uranium, plutonium and americium. One treatment scenario under study is to incinerate the organic materials, melt the metallic fraction and incorporate the mineral fraction (including ashes from organics incineration) into a glass matrix without sorting or pretreatment (grinding for instance). A scale 1 pilot of this PIVIC process (Process for Incineration and Vitrification In Can) has been commissioned in 2018 at the CEA R and D vitrification facility in Marcoule site. A R and D program aiming to demonstrate the feasibility of this process is currently on going. This paper starts with a description of PIVIC process with explanation of the technologies involved. Then, main results of the first year of operation with the technological demonstration goal are presented. (authors)

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗

Initial examination of fuel compacts and triso particles from the US AGR-2 irradiation test - 18443

Post-irradiation examination was completed on two as-irradiated compacts from the US Advanced Gas Reactor Fuel Development and Qualification Program's second irradiation test. These compacts were selected for examination due to indications that they may have contained particles that released cesium due to a failed or defective SiC layer. The coated particles were recovered from these compacts by electrolytic deconsolidation of the surrounding graphitic matrix in nitric acid. The leach-burn-leach (LBL) process was used to dissolve and analyze exposed metallic elements (actinides and fission products), and each particle was individually surveyed for relative cesium retention with the Irradiated Microsphere Gamma Analyzer (IMGA). Data from IMGA and LBL examinations provided information on fission product release during irradiation and whether any specific particles had below-average retention that could be related to coating layer defects or radiation-induced degradation. A few selected normal-retention particles and six with abnormally-low cesium inventory were analyzed using x-ray tomography to produce three-dimensional images of the internal coating structure. Four of the low-cesium particles had obviously damaged or degraded SiC, and x-ray imaging was able to guide subsequent grinding and polishing to expose the regions of interest for analysis by optical and electron microscopy. Additional particles from each compact were also sectioned and examined to study the overall radiation-induced microstructural changes in the kernel and coating layers. (authors)

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

The Production of Low Ash Coals Using the Hydrophobic-Hydrophilic Separation Process with Novel Developments

Froth flotation is a common mineral processing method in coal preparation. This process becomes less efficient, however, as particle size is reduced, and ultrafine particles are often discarded prior to froth flotation, contributing to a substantial amount of coal waste in impoundments. Because of the land-use and risk of an impoundment failure, these impoundments pose an environmental liability. To address ultrafine coal rejection, researchers at Virginia Tech developed the hydrophobic-hydrophilic separation (HHS) process. Unlike in froth flotation, HHS uses an organic solvent to separate and dewater hydrophobic particles from hydrophilic minerals. Past work on the HHS process yielded promising results. In particular, the HHS process has produced a low-ash (<2%) and low moisture (<8%) product, which is a viable feed stock for carbon products. In this work, an investigation of the effects of auxiliary processes on the HHS process was conducted. The auxiliary processes included grinding, pre-concentration, and reagent conditioning. This work also contains an investigation on the interaction between two primary unit operations in the HHS process: oil agglomeration and de-emulsification. Lastly, to make the HHS process more viable for commercial scale-up, a novel unit operation was developed and tested that performs comparably to the current HHS process.

01 COAL, LIGNITE, AND PEAT↗

Investigating the Effect of Water on the Mechanical Properties of Cellulose from Multiscale Molecular Dynamics Simulations

Classical molecular dynamics (MD) simulations provide insight into the structure and physicochemical properties of materials with atomic resolution. However, the length and time scales accessible to atomistic MD are orders of magnitude smaller than many relevant processes such as the response of a bulk material to experimentally accessible strain rates, which presents challenges when comparing models to experimental measurements. Bottom-up coarse-graining provides a means for systematically mapping atomistic information to lower resolution models to increase the length and time scales achievable by simulation. Cellulose is an abundant carbohydrate biopolymer with applications to many fields of research, such as materials science and renewable energy, due to its desirable mechanical properties and viability for conversion into biofuel. The effect of moisture content on the Young's modulus of cellulose is of special interest due to its native environment often being in the hydrated secondary plant cell wall and the grinding energy requirements for biomass feedstock preprocessing. The current work investigates the effects of water solvent on the Young's modulus of cellulose calculated from coarse-grained MD mechanical stress simulations. The coarse-grained model was parametrized from atomistic MD calculations of cellulose-cellulose potentials of mean force using umbrella sampling techniques under vacuum and solvated conditions. The Young's moduli of the coarse-grained cellulose assemblies parametrized from cellulose in vacuum or solvated in water were computed via mechanical stress simulations to highlight the importance of capturing solvent interactions for modeling the mechanical behavior of cellulose.

BASIC BIOLOGICAL SCIENCES,RADIATION PROTECTION AND↗

Thermal barrier systems and methods for access delay

Protective barrier includes a soft metal that inhibits or delays thermal or grinding attack tool penetration. The soft metal, which may be disposed between other layers and otherwise delays thermal attack by expanding or “puffing” during attack. The soft metal can inhibit mechanical attack by rapid ablation and wear of a cutting wheel or blade. The protective barrier may additionally include an oxide or carbide layer.

Brooks, Scott H.↗

Surface treatment of a sulfide glass solid electrolyte layer

Chemically treating ionically conductive sulfide glass solid electrolyte separators or separator layers can improve performance. In particular, treatment involving chemically etching a surface or surface region of the sulfide glass separator to blunt, lessen or remove edge defects or surface flaws, and/or to enhance surface smoothness is cost effective, reliable and well suited for high production environments compared to physical methods of removing scratches or smoothing surfaces, such as mechanical grinding and polishing.

Visco, Steven J.↗

Pulsed Electric Field Processing of Apples

Pulsed electric field (PEF) processing is a nonthermal technology that has the potential to improve the efficiency of apple processing, particularly for firm cultivars that are growing in popularity. This study evaluated the effects of PEF pretreatment on the processability and product quality of Cosmic Crisp apples, a modern cultivar known for its firmness. Apples were treated with PEF and assessed for tissue softening, mechanical energy requirements, particle size reduction, browning tendencies, and juice yield. PEF treatment significantly softened the apple tissue, as demonstrated by reduced compression forces in Instron testing, and this softening translated to decreased grinding energy during applesauce production. There were no changes to the particle size distribution of the resulting applesauce. PEF treatment also altered browning behavior and produced higher juice yields following mechanical disruption, suggesting enhanced membrane permeability and mass transfer. Together, these results show that PEF pretreatment can reduce mechanical energy demands and increase extractability without reducing product quality in firm apple varieties. These outcomes highlight the potential of PEF to increase the value recovered from processing-grade apples and to support more efficient and sustainable apple processing operations.

32 - ENERGY CONSERVATION, CONSUMPTION, AND UTILIZA↗

Anisotropic Hexagonal Boron Nitride Nanomaterials - Synthesis and Applications

Boron nitride (BN) is a synthetic binary compound located between III and V group elements in the Periodic Table. However, its properties, in terms of polymorphism and mechanical characteristics, are rather close to those of carbon compared with other III-V compounds, such as gallium nitride. BN crystallizes into a layered or a tetrahedrally linked structure, like those of graphite and diamond, respectively, depending on the conditions of its preparation, especially the pressure applied. Such correspondence between BN and carbon readily can be understood from their isoelectronic structures [1, 2]. On the other hand, in contrast to graphite, layered BN is transparent and is an insulator. This material has attracted great interest because, similar to carbon, it exists in various polymorphic forms exhibiting very different properties; however, these forms do not correspond strictly to those of carbon. Crystallographically, BN is classified into four polymorphic forms: Hexagonal BN (h-BN) (Figure 1(b)); rhombohedral BN (r-BN); cubic BN (c-BN); and wurtzite BN (w-BN). BN does not occur in nature. In 1842, Balmain [3] obtained BN as a reaction product between molten boric oxide and potassium cyanide under atmospheric pressure. Thereafter, many methods for its synthesis were reported. h-BN and r-BN are formed under ambient pressure. c-BN is synthesized from h-BN under high pressure at high temperature while w-BN is prepared from h-BN under high pressure at room temperature [1]. Each BN layer consists of stacks of hexagonal plate-like units of boron and nitrogen atoms linked by SP{sup 2} hybridized orbits and held together mainly by Van der Waals force (Fig 1(b)). The hexagonal polymorph has two-layered repeating units: AA'AA'... that differ from those in graphite: ABAB... (Figure 1(a)). Within the layers of h-BN there is coincidence between the same phases of the hexagons, although the boron atoms and nitrogen atoms are alternatively located along the c-axis. The rhombohedral system consists of three-layered units: ABCABC..., whose honeycomb layers are arranged in a shifted phase, like as those of graphite. Reflecting its weak interlayer bond, the h-BN can be cleaved easily along its layers, and hence, is widely used as a lubricant material. The material is stable up to a high temperature of 2300 C before decomposition sets in [2] does not fuse a nitrogen atmosphere of 1 atm, and thus, is applicable as a refractory material. Besides having such properties, similar to those of graphite, the material is transparent, and acts as a good electric insulator, especially at high temperatures (10{sup 6} {Omega}m at 1000 C) [1]. c-BN and w-BN are tetrahedrally linked BN. The former has a cubic sphalerite-type structure, and the latter has a hexagonal wurtzite-type structure. c-BN is the second hardest known material (the hardest is diamond), the so-called white diamond. It is used mainly for grinding and cutting industrial ferrous materials because it does not react with molten iron, nickel, and related alloys at high temperatures whereas diamond does [1]. It displays the second highest thermal conductivity (6-9 W/cm.deg) after diamond. This chapter focuses principally upon information about h-BN nanomaterials, mainly BN nanotubes (BNNTs), porous BN, mono- and few-layer-BN sheets. There are good reviews book chapters about c-BN in [1, 4-6].

36 MATERIALS SCIENCE↗

Understanding the Impact of Lignocellulosic Biomass Variability on the Size Reduction Process: A Review

The importance of size reduction to the commercial deployment of biomass utilization technologies cannot be overemphasized. Size reduction is necessary to create good flowing, easily digestible lignocellulosic biomass. However, inefficiencies and inconsistencies have not been well addressed for the process of size reduction. This has motivated quite a few research studies, some of which have reported the influence of process variables and pretreatment on the size reduction performance as well as the development of novel size reduction equipment and empirical mathematical models. In this Perspective, we present a systematic and critical evaluation of the state of lignocellulosic biomass size reduction research to provide insights for engineers and scientists for future development and investigation. We first briefly discuss the structural biology and failure mode of lignocellulosic biomass. Then, we present a comprehensive, data-driven picture of the interactions among lignocellulosic biomass attributes, size reduction process variables, pretreatment processes, and size reduction process performance (as defined by product characteristics and size reduction energy consumption). The sizing equipment tool wear issues are also summarized. Finally, we highlight some existing gaps and future research opportunities for lignocellulosic biomass size reduction to inform the development of newer technologies that could effectively produce high-value lignocellulosic biomass particles.

09 BIOMASS FUELS↗

The influence of mineralogical, chemical and physical properties on grindability of commercial clinkers with high MgO level

This research investigates various methods able to identify possible mineralogical, physical and chemical influences on the grindability of commercial clinkers with high MgO level. The aim of the study is to evaluate the hardness and elastic modulus of the clinker mineral phases and their fracture strength during the comminution processes, comparing samples from clinkers with low MgO level (0.5%) and clinkers with elevated MgO levels (> 5.0%). The study of the influence of mineralogical, chemical and physical properties was carried out using several analytical techniques, such as: optical microscopy, X-ray diffraction with Rietveld refinement (XRD) and X-ray fluorescence (XRF). These techniques were useful in qualifying the different clinker samples. The drop weight test (DWT) and the Bond ball mill grindability test were performed to characterize the mechanical properties of clinkers. Nanoindentation tests were also carried out. Results from the Bond ball mill grindability test were found to be related to the hardness of the mineral phase and to mineralogical characteristics, such as type and amount of inclusions in silicates, belite and alite crystals shape, or microcracked alites. In contrast, the results obtained by the DWT were associated to the macro characteristics of clinkers, such as porosity, as well as to the hardness and mineralogical characteristics of belite crystals in clusters. Hardness instrumented tests helped to determine the Vickers hardness and elastic modulus from the mineral phases in commercial clinkers and produced different values for the pure phases compared to previous publications.

36 MATERIALS SCIENCE↗

Micrometer-scale 3-D shape characterization of eight cements: Particle shape and cement chemistry, and the effect of particle shape on laser diffraction particle size measurement

Eight different portland cements were imaged on a synchrotron beam line at Brookhaven National Laboratory using X-ray microcomputed tomography at a voxel size of about 1 mum per cubic voxel edge. The particles ranged in size roughly between 10 mum and 100 mum. The shape and size of individual particles were computationally analyzed using spherical harmonic analysis. The particle shape difference between cements was small but significant, as judged by several different quantitative shape measures, including the particle length, width, and thickness distributions. It was found that the average shape of cement particles was closely correlated with the volume fraction of C{sub 3}S (alite) and C{sub 2}S (belite) making up the cement powder. It is shown that the non-spherical particle shape of the cements strongly influence laser diffraction results, at least in the sieve size range of 20 mum to 38 mum. Since laser diffraction particle size measurement is being increasingly used by the cement industry, while cement chemistry is always a main factor in cement production, these results could have important implications for how this kind of particle size measurement should be understood and used in the cement industry.

36 MATERIALS SCIENCE↗

Consolidation of cubic and hexagonal boron nitride composites

When we Consolidate cubic boron nitride (cBN) it typically requires either a matrix of metal bearing materials that are undesirable for certain applications, or very high pressures within the cBN phase stability field that are prohibitive to manufacturing size and cost. We present new methodology for consolidating high stiffness cBN composites within a hexagonal boron nitride (hBN) matrix (15–25 vol%) with the aid of a binder phase (0–6 vol%) at moderate pressures (0.5–1.0 GPa) and temperatures (900–1300 °C). The composites are demonstrated to be highly tailorable with a range of compositions and resulting physical/mechanical properties. Ultrasonic measurements indicate that in some cases these composites have elastic mechanical properties that exceed those of the highest strength steel alloys. Moreover, two methods were identified to prevent phase transformation of the metastable cBN phase into hBN during consolidation: 1. removal of hydrocarbons, and 2. increased cBN particle size. Lithium tetraborate worked better as a binder than boron oxide, aiding consolidation without enhancing cBN to hBN phase transformation kinetics. These powder mixtures consolidated within error of their full theoretical mass densities at 1 GPa, and had only slightly lower densities at 0.5 GPa. This shows potential for consolidation of these composites into larger parts, in a variety of shapes, at even lower pressures using more conventional manufacturing methods, such as hot-pressing.

36 MATERIALS SCIENCE↗

Effects of magnetic field annealing on the hard magnetic properties of milled Nd-Fe-B powders

In this study, we report the effect of magnetic field annealing (MA) in relieving the stress induced during the milling of Nd-Fe-B sintered magnets. The effect of MA processing parameters and particle size on the magnetic properties were investigated. Based on the results, magnetic field annealing is more effective in improving the magnetic properties of larger size particles, compared to finer particles. Our computational study on the role of particle surface defects in bi-modal particle distribution agrees with results obtained experimentally. In conclusion, magnetic field annealed powder has been successfully used to develop 4.6 g.cm -3 density bonded magnets with 75 vol% of magnetic powder and polyamide 12 (nylon 12) polymer binder resulting in 11.3 MGOe energy product.

36 MATERIALS SCIENCE↗

Large-Eddy Simulation of a wind turbine using a Filtered Actuator Line Model

When dealing with multirotor devices such as quadcopters or wind farms, the cost of blade-resolved large-eddy simulation (LES) becomes prohibitive. Combining LES with a family of lower-fidelity models, called actuator line models (ALMs), has grown in popularity in the past decade. ALM replaces full blade resolution with an array of actuator points or lines parameterized by aerodynamic lift/drag polar plots along the blades. Body forces computed based on these actuator points are then projected onto the LES flow mesh, mimicking the effect of rotating blades on the flow. However, the optimal projection radius and the associated LES grid size is often too restrictive for multirotor simulations. Recently, a new tip-correction-based filtered ALM (F-ALM) was proposed by Martinez-Tossas and Meneveau (2019), which allows coarser-than-optimal grids by avoiding the associated overprediction of thrust. In this work, F-ALM is implemented into a high-order, in-house LES code to simulate National Renewable Energy Laboratory Phase VI wind turbine. It is then followed by a comparison between the baseline ALM and the newly implemented F-ALM in terms of instantaneous and time-averaged flow fields and blade loads, revealing the advantages of F-ALM in preventing the overprediction of power on coarse grids. Finally, this encourages accurate and affordable simulations of multirotor devices in the future.

17 WIND ENERGY↗

Characteristics of carbonized sludge for co-combustion in pulverized coal power plants

Co-combustion of sewage sludge can destabilize its combustion profile due to high volatility, which results in unstable flame. We carried out fuel reforming for sewage sludge by way of carbonization at pyrolysis temperature of 300-500 deg. C. Fuel characteristics of carbonized sludge at each temperature were analyzed. As carbonization temperature increased, fuel ratio increased, volatile content reduced, and atomic ratio relation of H/C and O/C was similar to that of lignite. The analysis result of FT-IR showed the decrease of aliphatic C-H bond and O-C bond in carbonization. In the analysis result of TG-DTG, the thermogravimetry reduction temperature of carbonized sludge (CS400) was proven to be higher than that of dried sludge, but lower than that of sub-bituminous coal. Hardgrove grindability index increased in proportion to fuel ratio increase, where the carbonized sludge value of 43-110 was similar or higher than the coal value of 49-63. As for ash deposits, slagging and fouling index were higher than that of coal. When carbonized sludge (CS400) and coal were co-combusted in 1-10% according to calorific value, slagging tendency was low in all conditions, and fouling tendency was medium or high according to the compositions of coal.

01 COAL, LIGNITE, AND PEAT↗