Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “FAIR data”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Airborne MAX-DOAS Measurements Over California: Testing the NASA OMI Tropospheric NO2 Product

Airborne Multi-AXis Differential Optical Absorption Spectroscopy (AMAX-DOAS) measurements of NO2 tropospheric vertical columns were performed over California for two months in summer 2010. The observations are compared to the NASA Ozone Monitoring Instrument (OMI) tropospheric vertical columns (data product v2.1) in two ways: (1) Median data were compared for the whole time period for selected boxes, and the agreement was found to be fair (R = 0.97, slope = 1.4 +/- 0.1, N= 10). (2) A comparison was performed on the mean of coincident AMAX-DOAS measurements within the area of the corresponding OMI pixels with the tropospheric NASA OMI NO2 assigned to that pixel. The effects of different data filters were assessed. Excellent agreement and a strong correlation (R = 0.85, slope = 1.05 +/- 0.09, N= 56) was found for (2) when the data were filtered to eliminate large pixels near the edge of the OMI orbit, the cloud radiance fraction was<50%, the OMI overpass occurred within 2 h of the AMAX-DOAS measurements, the flight altitude was>2 km, and a representative sample of the footprint was taken by the AMAX-DOAS instrument. The AMAX-DOAS and OMI data sets both show a reduction of NO2 tropospheric columns on weekends by 38 +/- 24% and 33 +/- 11%, respectively. The assumptions in the tropospheric satellite air mass factor simulations were tested using independent measurements of surface albedo, aerosol extinction, and NO2 profiles for Los Angeles for July 2010 indicating an uncertainty of 12%.

remote sensing↗

Aerodynamic predictions and experimental results for an Advanced Manned Launch System orbiter configuration

The results from a series of wind-tunnel tests are presented along with predictions of the aerodynamic characteristics for a proposed Advanced Manned Launch System orbiter configuration. The predicted characteristics were made using the Aerodynamic Preliminary Analysis System (APAS), and were shown to be of sufficient accuracy for use in preliminary configuration analysis. Various methods of analysis were used in the APAS system, and the results of each were compared with the wind-tunnel dam. The accuracy of the predicted data varied over the Mach range studied. The best agreement between the wind-tunnel data and the APAS predictions occurr4ed in the low subsonic and the high supersonic regimes, while the low supersonic predictions resulted in only fair agreement. The APAS paneled-body analysis method (low speed) and the HABP impact analysis method (high speed) gave the most accurate results when compared against the experimental data.

Engelund, Walter C.↗

Data mining of space heating system performance in affordable housing

The space heating in residential buildings accounts for a considerable amount of the primary energy use. Therefore, understanding the operation and performance of space heating systems becomes crucial in improving occupant comfort while reducing energy use. This study investigated the behavior of occupants adjusting their thermostat settings and heating system operations in a 62-unit affordable housing complex in Revere, Massachusetts, USA. The data mining methods, including clustering approach and decision trees, were used to ascertain occupant behavior patterns. Data tabulating ON/OFF space heating states was assessed, to provide a better understanding of the intermittent operation of space heating systems in terms of system cycling frequency and the duration of each operation. The decision tree was used to verify the link between room temperature settings, house and heating system characteristics and the heating energy use. The results suggest that the majority of apartments show fairly constant room temperature profiles with limited variations during a day or between weekday and weekend. Data clustering results revealed six typical patterns of room temperature profiles during the heating season. Space heating systems cycled more frequently than anticipated due to a tight range of room thermostat settings and potentially oversized heating capacities. In conclusion, from this study affirm data mining techniques are an effective method to analyze large datasets and extract hidden patterns to inform design and improve operations.

32 ENERGY CONSERVATION, CONSUMPTION, AND UTILIZATI↗

CMS Space Monitoring

During the first LHC run, CMS stored about one hundred petabytes of data. Storage accounting and monitoring help to meet the challenges of storage management, such as efficient space utilization, fair share between users and groups and resource planning. We present a newly developed CMS space monitoring system based on the storage metadata dumps produced at the sites. The information extracted from the storage dumps is aggregated and uploaded to a central database. A web based data service is provided to retrieve the information for a given time interval and a range of sites, so it can be further aggregated and presented in the desired format. The system has been designed based on the analysis of CMS monitoring requirements and experiences of the other LHC experiments. In this paper, we demonstrate how the existing software components of the CMS data placement system, PhEDEx, have been re-used, dramatically reducing the development effort.

Ratnikova, N.↗

Pinpointing cosmic ray propagation with the AMS-02 experiment

The Alpha Magnetic Spectrometer (AMS-02), which is scheduled to be deployed onboard the International Space Station later this year, will be capable of measuring the composition and spectra of GeV-TeV cosmic rays with unprecedented precision. In this paper, we study how the projected measurements from AMS-02 of stable secondary-to-primary and unstable ratios (such as boron-to-carbon and beryllium-10-to-beryllium-9) can constrain the models used to describe the propagation of cosmic rays throughout the Milky Way. We find that within the context of fairly simple propagation models, all of the model parameters can be determined with high precision from the projected AMS-02 data. Such measurements are less constraining in more complex scenarios, however, which allow for departures from a power-law form for the diffusion coefficient, for example, or for inhomogeneity or stochasticity in the distribution and chemical abundances of cosmic ray sources.

79 ASTRONOMY AND ASTROPHYSICS↗

Complex configuration analysis at transonic speeds

Advanced performance requirements of new combat and transport aircraft together with design time constraints intensify the development and application of three dimensional computational analyses. A computational method which was developed for the specific purpose of providing an engineering analysis of complex aircraft configurations at transonic speeds. Particular attention is given to the recently incorporated wing viscous interaction and canard capabilities. The treatment of fuselage fairings, nacelles, and pylons is reviewed. The means for keeping computing resources at reasonable levels are identified. Three configurations were selected for correlations with experimental data. Taken together, the comparisons illustrate the full extent of current analysis capabilities. The configurations include: (1) a wing fuselage canard fighter; (2) a transport with fuselage fairings, four nacelles, four pylons; and (3) a space vehicle which includes an external fuel tank and rocket boosters (transonic launch configuration).

Boppe, C. W.↗

Line profile analysis of dislocation densities of the δ-phase 239 Pu-2.0 at%Ga alloy using neutron diffraction

Time-of-flight neutron diffraction measurements were conducted at ambient conditions to study microstructures of the δ-phase 239 Pu-2at% Ga alloy. Based on the line profile analysis of diffraction data we derived dislocation densities using a correction routine to account for the anisotropic strain broadening. Our results show here that the average dislocation density in the as-received sample, previously treated at cryogenic temperatures, is five times higher than the dislocation density measured after annealing the sample, indicating that the neutron instrumentation used in this work has sufficient resolution to detect the dislocation density changes in different sample processing. These results are also in reasonably good agreement with the dislocation densities previously reported based on TEM observations and x-ray diffraction data, suggesting that the simple correction routines applied in this work have a fairly good fidelity for deriving important microstructural information such as dislocation density for elastically highly anisotropic δ-phase 239 Pu-Ga alloys.

36 MATERIALS SCIENCE↗

Kinetic modeling of ignition in miniature shock tube

The ignition delay times of toluene, n-heptane/iso-octane primary reference fuel blends, and toluene/n-heptane/iso-octane toluene primary reference fuel blends were studied in the miniature high repetition rate shock tube (HRRST). In the HRRST, the temperature and pressure change during the test time, complicating interpretation of ignition delay times. Two methods of chemical kinetic modeling were employed in order to account for the changing thermodynamic states in the HRRST. One was based on direct modeling using the pressure profile and the kinetic mechanism, and the other was based on a Livengood-Wu type approach using modeled constant volume ignition delay times. Two different kinetic mechanisms were used in modeling the data. Both methods showed agreement with experimental data over a range of temperatures, pressures, and blends. While overall agreement was fair, agreement was poorer for one of the mechanisms for the primary reference fuel blends. An evaluation of the ignition delay iso-contours from these mechanisms for representative HRRST experiment thermodynamic trajectories revealed that the HRRST measured IDTs are controlled by the high temperature chemistry and are more sensitive to temperature. Furthermore, the different performance of mechanisms is therefore attributed to their different high temperature reactivity.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

A ROLE OF MAGNETOSONIC PULSES ON VARIATIONS OF VOYAGER-1 MeV ELECTRON INTENSITY IN THE HELIOSHEATH

Voyager 1 (V1) spacecraft observed electrons of 6-14 MeV in the heliosheath which showed several enhancements of significant flux variation. We compare these temporal electron flux variations, from the time when V1 crossed the termination shock (TS) up to mid-2008, with dynamical phenomena in the heliosheath that are obtained from our MHD simulations which are based on Voyager 2 (V2) observed solar-wind data. Our simulations indicate that all electron flux enhancements, except for one, correspond fairly well to the times when a magnetosonic (MS) pulse was driven downstream of the TS due to collision of interplanetary shock (IPS) or shock-driven MS pulse and its reflection in the heliosheath that either passed V1, or collided with the TS or with the plasma sheet near the heliopause (HP). This result suggests that these enhancements in the electron flux should correspond to either direct or indirect effects of MS pulses in the heliosheath driven by IPSs. The scale of the heliosphere is estimated by comparing V1-observed magnetic field intensity with the simulated intensity which suggests that V1 is possibly located near the HP within 4-8 AU at the present time.

79 ASTRONOMY AND ASTROPHYSICS↗

Crosswell Seismic Amplitude-Versus-Offset for Detailed Imaging of Facies and Fluid Distribution within Carbonate Oil Reservoirs

Crosswell seismic surveys were conducted at two fields in northern Michigan. One of these, Springdale, included two monitor wells that are located external to the reef, and the other, Coldspring, employed two production wells within the reef. The Springdale wells extended to much greater depths than the reef, and imaging was conducted from above and from beneath the reef. The resulting seismic images provide the best views of pinnacle Niagaran reefs obtained to date. The tops of the reservoirs can be clearly distinguished, and their lateral extent or dipping edges can be observed along the profile. Reflecting events internal to the reef are evident; some of them are fairly continuous across the reef and others are discontinuous. Inversion of the seismic data indicates which events represent zones of higher porosity and which are lower porosity or even anhydrite plugged. The full stacked image includes angles that are beyond critical for many of the interfaces, and some reflections are visible only for a small range of angles, presumably near their critical angle. Stacking these angles in provides an opportunity for these events to be seen on the stacked image, where otherwise they would have been unrecognized. For inversion, however, the complexity associated with phase changes beyond critical can lead to poor results, and elastic inversion of partial angle stacks may be best conducted with restrictions to angles less than critical. Strong apparent attenuation of signals occurs when seismic ray paths pass through the upper part of the Springdale reservoir; this may be due to intrinsic attenuation and/or scattering of events due to the locally strongly varying gas saturation and extremely low fluid pressures. Signal-to-noise limitations become evident far from the source well in the Coldspring study, probably because the raw data were strongly affected by tube-wave noise generated by flow through the perforation of the receiver well. The seismic images obtained, and interpretations of them, as assisted by Amplitude-versus-Angle studies and accompanying inversion, provide additional insight into the internal geometry of these two reefs and provide data that should be useful for reservoir management.

02 PETROLEUM↗

Development of procedures for calculating stiffness and damping properties of elastomers in engineering applications. Part 1: Verification of basic methods

The primary aim of this investigation was verification of basic methods which are to be used in cataloging elastomer dynamic properties (stiffness and damping) in terms of viscoelastic model constants. These constants may then be used to predict dynamic properties for general elastomer shapes and operating conditions, thereby permitting optimum application of elastomers as energy absorption and/or energy storage devices in the control of vibrations in a broad variety of applications. The efforts reported involved: (1) literature search; (2) the design, fabrication and use of a test rig for obtaining elastomer dynamic test data over a wide range of frequencies, amplitudes, and preloads; and (3) the reduction of the test data, by means of a selected three-element elastomer model and specialized curve fitting techniques, to material properties. Material constants thus obtained have been used to calculate stiffness and damping for comparison with measured test data. These comparisons are excellent for a number of test conditions and only fair to poor for others. The results confirm the validity of the basic approach of the overall program and the mechanics of the cataloging procedure, and at the same time suggest areas in which refinements should be made.

Chiang, T.↗

Measured backscatter and attenuation properties, including polarization effects, of various dispersions at 0.9 micron

The optical properties of a wide variety of atmospheric dispersions were studied using a 0.9-micron lidar system which included a GaAs laser stack transmitter emitting a horizontally polarized beam of 4 milliradians vertical divergence and 1.5 milliradians horizontal divergence. A principal means for assessing optical properties was the polarization ratio, that is, the backscattered radiation power perpendicular to the transmitter beam divided by the backscattered radiation power parallel to the beam polarization. The ratio of the backscattered fraction to the attenuation coefficient was also determined. Data on the dispersion properties of black carbon smoke, road dust, fog, fair-weather cumulus clouds, snow and rain were obtained; the adverse effects of sunlight-induced background noise on the readings is also discussed.

Kohl, R. H.↗

Comparison of theoretical predicted longitudinal aerodynamic characteristics with full-scale wind tunnel data on the ATLIT airplane

An analytical method is presented for predicting the lift coefficient, the pitching moment coefficient, and the drag coefficient of light, twin-engine, propeller-driven airplanes. The method was applied to the Advanced Technology Light Twin-Engine airplane. The calculated characteristics were then correlated against full scale wind tunnel data. The analytical method was found to predict the drag and pitching moment fairly well. However, the lift prediction was extremely poor.

Vandam, C. P. G.↗

The resonance lines of MG2 as diagnostics of the upper solar chromosphere

The resonance lines of singly ionized magnesium, the MgII h&k lines at about 280 nm, are two of the small number of lines in the solar spectrum that are optically thick in the chromospheric part of the solar atmosphere. Potentially these lines contain information on the initial temperature rise that occurs at the top of the photosphere. Unfortunately, few good observations of the lines exist due to their wavelength near 280 nm the ultraviolet. However, a fair number of observations (on the order of 200) are available from the data base of the UltraViolet Polarimeter and Spectrometer (UVSP) instrument that flew on board of NASA's Solar Maximum Mission (SMM) satellite. In addition, this data base contains a number of spectra that include the Mg I resonance line at (lambda)285.2nm, just longward of the h&k lines. The neutral magnesium line is not as strong as its ionic counterparts and samples slightly lower parts of the atmosphere. Its width is a sensitive diagnostic of the ionization balance between neutral and singly ionized magnesium, which determines the opacity scale (and formation height) of other diagnostically important MgI lines like the 457.1 nm intercombination line, the magnesium b lines and the infrared MgI emission lines near 12 microns. Analysis of the observed line profiles shows that it is necessary to include the effects of partial frequency redistribution (PRD) in the formation of the line as in the case of the h&k lines. This implies that the core of the line is very sensitive to the way scattering is treated in the modeling of the line, and in turn this allows us to separate the uncertain effects in the atomic data (viz. the Van der Waals broadening) from the uncertainties in the underlying atmospheric model. The main objective of this research was to compare observed spectra of the magnesium resonance lines against theoretical line profiles calculated from recent models of the solar atmosphere by Fontenla et al., hereafter called FAL. These models extend earlier solar models by Avrett et al. and provide yet a better match between observed and calculated spectra, in particular of the hydrogen Lyman line, by including the effects of ambipolar diffusion of hydrogen and helium in the mass and energy transport equations for the chromosphere-corona transition region. Although the transition region models can be built self-consistently (without additional observational input) once the proper boundary conditions are given at the top of the chromosphere, there are uncertainties in the models precisely because these boundary conditions are not well known. With the analysis of UVSP magnesium observations we strive to constrain these uncertainties.

Avrett, Eugene H.↗

Vapor generator wand

In low speed wind tunnels it is often desirable to visualize airflow to augment observations made with instruments such as strain and pressure gages. Current technology devices for delivery of a vapor are bulky and thus disrupt local airflow. It is the object of this invention to provide a device capable of delivering a stream of vapor with a minimal effect on local airflow. The present invention achieves this object by utilizing a narrow tube as a heating device for producing the vapor. Running an electrical current through the tube provides resistive heating to a liquid which produces a vapor when boiled. As the entire heating and delivery portion of the device is simply a small cylinder the disruption to airflow within the tunnel is minimized. this allows an experimenter to place the source of vapor fairly close to a model without causing too much change to the model data. The novelty of the present invention lies in reducing the bulk of current technology devices by combining the acts of heating and delivery.

Robelen, David B.↗

Dispersed ion structures at the poleward edge of the auroral oval: Low-altitude observations and numerical modeling

We have compared the AUREOL 3 (A3) observations of auroral ion precipitation, particularly ion beams, with the results from the global kinetic model of magnetotail plasma of Ashour-Abdalla et al. (1993). We have identified 101 energetic keV H(+) velocity dispersed precipitating ion structures (VDIS) with fluxes above 10(exp -3) ergs./sq cm./s in the A3 record between the end of 1981 and mid-1984. These beams display a systematic increase in energy with increasing latitude and were observed in a narrow region within less than 1 deg in latitude of the polar cap boundary. The VDIS are the most distinctive feature in the auroral zone of the plasma sheet boundary layer. We report first on a statistical analysis of the possible ralationships between magnetic activity or substorm phase and the VDIS properties. Our particle simulations of the precipitating ions have been extended by using a series of modified versions of the Tsyganenko (1989) magnetic field model and by varying the cross-magnetosphere electric field. In the simulations, plasma from a mantle source is subject to strong nonlinear acceleration, forming beams which flow along the PSBL. Only 3 to 4% of these beams precipitate into the ionosphere to form the VDIS while the majority return to the equatorial plane after mirroring and form the thermalized central plasma sheet. The final energy and the dispersion of the beams in the model depend on the amplitude of the cross-tail electric field. Two unsual observations of low-energy (less than 5 keV) O(+) VDIS, shifted by 4 deg 5 deg in invariant latitude equatorward of H(+) VDIS are analyzed in detail. The sparsity of such O(+) events and the absence of the changes in the flux and frequency of occurrence indicate a solar wind origin for the plasma. Finally, large-scale kinetic modeling, even with its simplifications and assumptions (e.g., static magnetic field, solar wind source), reproduces low-altitude auroral ion features fairly well; it may therefore be presented as an appropriate framework into which data on energization and transport of the hot plasma, obtained in the equatorial plane, could be inserted in the near future.

Bosqued, J. M.↗

NASA Researcher Demographics

NASA is committed to supporting a research environment that is fair and equitable. In order to promote opportunity for everyone, NASA is collecting data on the demographic makeup of its research community with the aim of using this data to support decision making in future programs and projects. This report summarizes the demographic data we have collected for the Science Mission Directorate since 2016.

demographics↗

Multiscale Modeling of Thermoplastics Using Atomistic-informed Micromechanics

A multiscale repeating unit cell model of a single spherulite containing four disparate length scales was developed to predict the thermoelastic behavior of semicrystalline thermoplastic materials for composite aerospace applications. The continuum level scales were fully coupled and modeled using the generalized method of cells and the high fidelity generalized method of cells micromechanics theories. Data from molecular dynamics simulations were used as inputs for the amorphous and crystalline constituents in the multiscale continuum models. Effective Young’s modulus, shear modulus, Poisson’s ratio, coefficient of thermal expansion, and thermal conductivity were predicted for polyether ether ketone and polyether ketone ketone, showing good agreement with the available experimental data from the open literature. Moreover, it is shown that predicted properties are fairly insensitive to the fidelity of the micromechanics model used at the highest continuum scale or the assumed shape of the spherulite.

thermoplastics↗