Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “EXPERIMENTAL REACTORS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2020

Experimental investigation of turbulent wake flows in a helically wrapped rod bundle in presence of localized blockages

In nuclear sodium fast reactors, bundles of rods are tightly packed into a triangular lattice, enclosed in a hexagonal duct, and each pin is spirally wrapped with a thin wire. Flow blockages can potentially impact the local flow characteristics and heat transfer mechanisms in the bundle due to its small subchannel size. The effects of the blockage on the flow structures and heat transfer mechanisms are important aspects that require an accurate investigation. In this study, the flow-field characteristics in the vicinity of a blockage located in the exterior subchannel of rod bundles with helically wrapped wires were experimentally investigated. The velocity fields in the exterior subchannel were acquired by applying matched-index-of-refraction and time-resolved particle image velocimetry (TR-PIV) techniques for Reynolds numbers of Re 1 = 4000 and Re 2 = 17 000, i.e., equivalent to Rew 1 = 19 600 and Rew 2 = 83 200, respectively, based on the blockage width. The results from the TR-PIV measurements revealed an arch-shaped vortex with a large flow recirculation and a pair of counter-rotating vortices in the wake region downstream of the blockage, which is commonly observed in the wake flow of bluff bodies. The relative lateral distance and angle between the two vortices decreased when the Reynolds numbers increased. Profiles of maximum turbulence intensity along the shear layers illustrated the transition process including the growth, peak, and decay along the flow direction. From the spectral analysis of the turbulent velocities extracted at points along the shear layer, the Strouhal numbers ( St ) representing the vortex shedding frequency were found to be St = 0.25 and St = 0.56 for the left and right shear layers, respectively. Characteristics of shear layers generated by the blockage in the exterior subchannel were investigated via the two-point cross correlation of fluctuating velocities. The patiotemporal cross correlations of turbulent velocities, computed at points in the region where the left shear layer exhibited rolling effects and vortex breakdowns, were considerably wider and longer. The convection velocity U c was estimated to be ~0.82 U m to 0.93 U m . Proper orthogonal decomposition (POD) analysis was applied to the instantaneous velocity fields to extract the statistically dominant flow structures. It was found that POD modes 2–3 and 4–5 formed the pair modes when the corresponding POD temporal coefficients depicted sinusoidal shapes and exhibited nearly circular orbits in the phase space. Spectral analysis of the POD temporal coefficients confirmed the vortex shedding frequencies detected in the analysis of turbulent velocities.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Simulation of natural circulation cartridge loop experiments and application to molten salt reactors

This work uses the TRAC/RELAP Advanced Computational Engine (TRACE) thermal hydraulics (TH) code to model natural circulation cartridge loop experiments previously conducted at Oak Ridge National Laboratory (ORNL) using water and compares the simulated and experimental results. TRACE is also used to characterize natural circulation in the cartridge loop vehicle using FLiNaK as the working fluid. The experimental vehicle is a buoyancy-aided, annular cartridge loop, referred to as a thermosyphon, and is designed to aid in qualifying liquid–fueled and/or liquid–cooled irradiation experiments for the Versatile Test Reactor (VTR), which is currently being designed in the United States. Out-of-pile water experiments have been conducted using the cartridge and the Thermosyphon Test Loop facility at ORNL, and future experiments are anticipated that would use other molten salt surrogates as the working fluid, followed by eventual insertion of a similar cartridge into VTR. Additionally, this work aims to determine how well TRACE can replicate the natural convection conditions that were observed experimentally; this serves as an initial step for validating the modeling tool for design and safety calculations to support future irradiation experiments in VTR. Initial predictions of potential experiments were made using FLiNaK as the natural circulation fluid to demonstrate the relevance of the cartridge design to molten salt reactors (MSRs). Results from this study indicate that TRACE can accurately capture natural convection phenomena in the thermosyphon and that several design changes to the current cartridge vehicle are necessary to achieve hydraulic conditions similar to those expected in MSRs.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2023

CNRS Molten Salt Reactor Benchmark Analysis Using Griffin-Pronghorn Coupled Multi-physics Code System

Molten salt reactors (MSRs) with flowing fuel have the unique feature of utilizing the fuel salt for heat generation and extraction at the same time, since the fuel salt is circulating through the whole primary loop. This movement of fuel salt results in a partial decay of the delayed neutron precursors (DNPs) outside the core and the corresponding redistribution of the DNPs in the active region of the core. To capture this effect, neutronics and thermal-hydraulics (T/H) codes need to be able to handle the movement of DNPs and their decay [1, 2]. Idaho National Laboratory (INL) is actively working on developing the neutronics and T/H codes to model the MSRs with flowing fuel. As one of the efforts, the neutronics code Griffin [3] and the T/H code Pronghorn [4] that are built upon the MOOSE framework [5] have been extended to handle the flowing fuel involving the drift of DNPs, and this capability is being tested and verified with MSR benchmark problems including the CNRS benchmark problem [6]. Additionally, a multi-physics analysis of the molten salt reactor experiment (MSRE) is being conducted to verify and validate the codes against available experimental data [7]. This work presents the analysis of the CNRS benchmark problem using the Griffin-Pronghorn coupled multi-physics code system of INL. Both steady-state and transient problems are analyzed, and the results are compared with those of other participants presented in [6]. The following section provides a description of the benchmark, along with input parameters and observables for each step. Then, the results for each step are presented in comparison with other participants’ results, followed by summary and conclusion.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

Elucidating the Impact of Flow on Material-Sensitive Critical Heat Flux and Boiling Heat Transfer Coefficients: An Experimental Study with Various Materials

In this work, steady-state internal flow boiling critical heat flux (CHF) experiments were carried out at 10°C inlet subcooling and atmospheric pressure (84 kPa at an altitude of about 5300 feet) with mass flux ranging from 200 to 2,000 kg/m 2 -s on seven tube materials, including the accident-tolerant fuel cladding candidate FeCrAl (C26M) alloy. At a relatively low flow rate, the sensitivity of CHF to different materials was appreciable (the average difference among the tested materials was 19% at 200 kg/m 2 -s). As the absolute CHF differences stayed constant for higher flow rates, the increased flow rate led to reduced relative CHF differences among the tested materials (average relative difference of 15% at 1,000 kg/m 2 -s). FeCrAl alloy claddings that were oxidized under simulated Light Water Reactor (LWR) conditions yielded CHF comparable to as-received FeCrAl alloy cladding, with less than 1.8% difference. Experimental CHF results imply marginal material sensitivity impacts on the departure from nucleate boiling ratio in steady-state nuclear reactor cores. Yet, for accident progression analysis, material sensitivity may hold importance, as boiling behavior variation at low mass flux is appreciable. Macroscopic material parameters (surface wettability, surface roughness, and thermal properties) do not provide a suitable explanation for observed material-sensitive CHFs. Yet, surface roughness and thermal effusivity revealed power and linear relations, respectively, to the nucleate boiling heat transfer coefficients at low mass flux. At high mass flux, material sensitivity on nucleate boiling heat transfer significantly decreased due to the increased shear stress on boiling surface overwhelming material-related boiling implications.

36 MATERIALS SCIENCE↗
DOE OSTI2025

High-Fidelity CFD Modeling of Cryogenic Hydrogen Isotope Extrusion for Fusion Reactor Pellet Fueling

This study investigates the extrusion processes of deuterium and protium using ANSYS-Polyflow. The geometries and computational fluid dynamics (CFD) settings closely replicate the experimental setups and data acquired from the extruder experiments at Oak Ridge National Laboratory (ORNL) for validation purposes. We explore the impacts of (1) slip versus non-slip boundary conditions and (2) the use of constant, temperature-, and shear rate–dependent viscosities, concluding that the implementation of non-slip wall boundary conditions combined with shear rate–dependent viscosity produced more accurate predictions. The simulations achieved excellent agreement with the experimental data, with relative differences of only 5% for deuterium, and 3% to 6% for protium. This is the first time that experimental extrusion data at ORNL have been accurately predicted through high-fidelity CFD modeling. In conclusion, the advancements offer valuable insights and a foundational modeling tool for optimizing pellet injectors for ITER and other future reactor-scale devices.

ANSYS-Polyflow↗
DOE OSTI2025

CFD Simulations of Lower Plenum Mixing

Review of model development and validation performed in the Advanced Reactor Technologies (ART) program for thermal mixing at the outlet of High Temperature Gas Reactors (HTGRs). Understanding the mixing that occurs in the lower plenum in an HTGR is necessary to facilitate design improvements and to perform reactor safety analysis. Numerical models are one possible approach to gain a better understanding of mixing in the lower plenum. Given the complexity of the geometry and the intense mixing present, it is important to perform validation of numerical models. Three models have been developed during FY2025: a porous media with Pronghorn, a Reynolds Averaged Navier Stokes (RANS) with STAR-CCM+, and a Large Eddy Simulation (LES) with NekRS. The reference facility is a scaled-down version of the lower plenum of the High Temperature Gas-Cooled Reactor - Pebble-bed Module (HTR-PM) demonstration reactor. Preliminary results of the porous media and the RANS shows general good agreement against experimental benchmark data. Future work will leverage high-fidelity results obtained through LES to guide model selection and improvements to the lower-fidelity models, with particular attention to the Pronghorn porous media.

22 - GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Molten Salt Reactors: What about Materials? An Overview and Future Needs

ORNL Molten Salt Reactor Experiment (MSRE) – 60’s- early 70’s Developed INOR-8 (aka Hastelloy N); MSRE operated over the period Dec 1965 to 1969. (not continuous); Operated for >13,000 hr at T from ~550 to ~650°C using U, Li-7, Be and Zr fluoride salt fuel; Post-Irradiation Material Evaluation (corrosion + neutron irradiation) of surveillance specimens; Noted ”beneficial effect of Nb” in alloy (on intergranular Te embrittlement) More recent (post-1980) Materials R&D for Gen IV …. Alloys 316L, 316H, 304, Alloy 800H, Alloy 617 (!!), Hastelloy N (mod), plus numerous experimental alloys developed

36 - MATERIALS SCIENCE↗
DOE OSTI2025

MOSCATO Development and Integration in Fiscal Year 2025: Implementation of Multiphase, Multiphysics Modeling Capabilities for Molten Salt Systems

MOSCATO (Molten Salt Chemistry and Transport) is a multiphysics code that provides high-fidelity, coupled simulations of fluid flow, heat transfer, mass transfer, chemistry, electrochemical phenomena, and alloy corrosion for molten salt systems. In FY25, significant developments were made to the code package, enhancing its capabilities for modeling all relevant phenomena within operating moltens salt reactors (MSRs). The developments and activities in FY25 included: 1. Implementation of Level-Set methods to enable modeling of single-bubble behavior in molten salts. In FY25, the Level-Set two-phase flow modeling implementation was improved to simulate single bubble behavior with molten salt media. The large density and viscosity ratios between typical gases and molten salt liquids present challenges for these types of numerical solvers. With enhancements to the pressure projection method, MOSCATO’s Level-Set solver was able to be successfully validated to experiments related to helium bubble rise in stagnant molten salt. The simulated bubble rising velocity showed reasonable good agreement with experimental measurements. The bubble shape and dynamics were also visually compared with experimental snapshots, demonstrating a good qualitative match. 2. Generation of mass transfer correlations for multiphase flow systems. To enable calculations of the tritium transport across the interface between gas bubbles and salt, we modeled high- Schmidt-number mass transfer around a sphere across a broad range of Reynolds numbers. The mesh near the sphere surface was highly refined to resolve steep concentration gradients caused by the low diffusion coefficient. Literature-based mass transfer correlations were compared with the numerical results, and modifications were proposed to improve agreement, particularly at higher Schmidt numbers. These mass transfer correlations were subsequently provided to other national laboratories to help enable high quality mass transfer simulations using lower-order solvers under development within the NEAMS program. 3. Preliminary implementation of a bubbly flow solver. To model bubbly flow in molten salt, we implemented a bubbly flow solver for void fractions less than 5%. To do so, an algebraic relative velocity model that assumes small bubbles with rapid momentum equilibration was added to MOSCATO to compute bubble velocities. Preliminary comparisons with experimental data showed reasonable agreement, and further improvements are underway. 4. Generation of mass transfer correlations for MSRE subchannel The Molten-Salt Reactor Experiment (MSRE) was a landmark historical project that demonstrated the feasibility of molten-salt reactor technology. The MSRE campaign also generated a significant body of experimental data and reports that continue to support molten-salt–related research. In this report, the MSRE core subchannel was used as the reference geometry for a mass transfer study performed with MOSCATO. The geometry and computational mesh were adapted from a previous study, providing adequate resolution for the relatively low Reynolds number in this case. Additional mesh refinement was applied to reach higher Schmidt numbers, enabling the derivation of a reliable mass-transfer correlation for the present scenario. 5. Simulations of oxygen ingressions into molten salt. In the previous fiscal year, we initiated a study to simulate oxygen ingression in stagnant salt. As oxygen enters the salt through its surface, it reacts with Ce 3+ to form solid CeO 2 and other reaction products. To more fully capture the complex diffusion-convection-reaction mechanisms, capabilities for modeling natural convection in the salt vessel were added. These were needed as the flow of the ingressed gas induced flow in the salt caused by surface shear and non-isothermal effects. With these updated physics in place, we were able to successfully reproduce the experimental results for the rate of change of CeCl 3 concentrations versus time. 6. Flow corrosion model validation. In FY24, MOSCATO’s corrosion model was validated against static corrosion experiments. In FY25, this work was extended to a flow corrosion experiment, where FLiNaK salt was driven by natural convection, with initial salt impurities to initiate corrosion. Despite uncertainties in parameters such as elemental diffusion coefficients in the alloy and unknown H + concentrations, the simulations achieved good agreement with experimental results, especially in predicting sample mass losses.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Exploring Fission–Fusion Synergies to Accelerate Compatibility Understanding

To address the significant commercial interest in fusion energy, it will be necessary to accelerate the compatibility research associated with liquid breeders including Li, eutectic Pb–Li and LiF-BeF 2 (FLiBe) molten salt. Particularly for FLiBe, compatibility understanding is limited especially for fusion relevant materials such as reduced activation ferritic-martensitic steels, SiC and V alloys. The historical knowledge associated with molten salt reactors (MSRs) and recent work to commercialize MSRs can benefit fusion research. Recent experimental and modeling work has improved understanding and this knowledge can be applied to fusion relevant materials. For liquid metals (LMs), the comparisons to Li and Pb–Li are less direct but nevertheless can help guide the pathway toward commercialization. For Pb–Li, Al-rich coatings have been shown to inhibit dissolution and potentially increase operating temperatures. For commercialization, the experience with sensors and on-line cleanup can help guide future developments. Thus, it is worth considering the potential for fission-related research with LMs and molten salts to help accelerate fusion research.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Exploring NaCl-PuCl 3 molten salts with machine learning interatomic potentials and graph theory

Actinide molten salts are the basis of the liquid fuels used in molten salt reactors. Due to the inherent difficulties associated with high temperature and hazardous conditions, experimental investigations of fundamental properties of these materials are usually challenging. In this work, we describe the structure and transport of NaCl-PuCl 3 mixtures using computational techniques. Three compositions were considered (16, 25, and 36 mol% PuCl 3 ) over a temperature range (730 – 1257K) using ab initio molecular dynamics, which provided the necessary data sets for training machine learned interatomic potentials. Further, molecular dynamics simulations based on these potentials were then used to determine structure and transport properties. A substantial change was noted in the structure factor when increasing the PuCl 3 content from 25 to 36 mol%. This change is linked to the aggregation of larger Pu 3+ clusters. In addition, the similarity of the atomic environments of metal cations in molten salt systems to their solid states counterparts was investigated using an unsupervised learning technique. Finally, graph theory was employed to explore the structure and size of actinide networks. Consistent with the structure factor, a dense Pu 3+ intermolecular structure is observed within the 36 mol% PuCl 3 mixture. The structure of cation-cation inter-junctions is also discussed. In all cases, the diffusion of Pu 3+ is significantly lower than that of Na + and Cl - .

36 MATERIALS SCIENCE↗
DOE OSTI2026

ab initio Sub-Mechanism Development for Cyclopentene Oxidation

To accurately predict low-temperature oxidation behavior, chemical kinetics mechanisms must contain complete reaction networks that include detailed consumption reactions of intermediates produced directly from hydroperoxyalkyl radicals, Q̇OOH, which undergo competing unimolecular reactions and bimolecular reactions with O2. Rates of chain-branching are governed by the flux between the two competing pathways, and inherently depend on temperature, pressure, and oxygen concentration. Neglect of consumption pathways for major oxidation intermediates leads to mechanism truncation error that is ameliorated by expanding the level of detail included in sub-mechanisms and employing ab initio methods for computing rates of elementary reactions and thermochemical properties of species involved. In the present work, an ab initio-derived sub-mechanism is developed using AutoMech to model the chemical kinetics of cyclopentene, a major product of cyclopentane oxidation. The ab initio sub-mechanism builds on a detailed mechanism developed using Reaction Mechanism Generator (RMG) for the specific purpose of determining the extent to which replacing cyclopentene-specific reactions and species with quantum chemical computations reduces model inaccuracies resulting from mechanism truncation error. In an effort to minimize interference from other reactions present during the formation of cyclopentene from cyclopentyl + O2, providing a narrower experimental scope, the model is compared against speciation measurements from jet-stirred reactor (JSR) experiments on cyclopentene oxidation. The experiments utilize vacuum ultraviolet-absorption spectroscopy and mass spectrometry for isomer-resolved speciation of intermediates at 835 Torr from 700 – 950 K. [O2]-dependent experiments were also conducted from 0.057 – 2.01 · 1018 molecules cm–3 at 825 K to examine the influence of oxygen on species profiles. Model predictions using the ab initio-revised mechanism yielded significant improvements in species profiles for both the temperature- and [O2]-dependent measurements, owing in part to increased rates of HOȮ and H2O2 production, which underscores the influence of theoretical calculations of reaction rates involving species produced from Ṙ + O2 such as cyclopentene.

AutoMech↗
DOE OSTI2026

Directional dependence of equilibrated TLD-400 chips in multiple radiation fields

Fielding of thermoluminescent dosimeters (TLDs) for measurement of photon radiation dose in experiments is the standard practice for γ-irradiation facilities, pulsed power x-ray facilities, and reactor facilities at Sandia National Laboratories (SNL). Due to the high-dose experimental conditions and the mixed ( 1 n, γ) fields in these facilities, SNL radiation metrologists have historically used CaF 2 :Mn TLDs (also known as TLD-400). Recent inquiries to the radiation metrology staff have raised concerns that the aluminum-equilibrated TLD-400 chips may exhibit a directionally dependent response. The metrologists were asked whether the dose measured by the chip may be impacted by the angle of incidence on the equilibrated TLD. To provide a thorough answer to this query, a set of adjoint Monte Carlo radiation transport calculations was performed for three different equilibrated TLDs as well as bare TLD chips using the Integrated Tiger Series (ITS) code. The key feature of the adjoint calculations performed in this study is that each photon escaping the modeled geometry was tallied into angular bins to provide information on both the energy and angular dependence of the equilibrated chip. After the adjoint Monte Carlo calculations were completed, the resulting energy-dependent response function for each angular bin was convolved with multiple photon energy spectra representing various radiation facilities at SNL. The radiation facilities selected for analysis span a range of photon energies from approximately 1 keV up to approximately 20 MeV. Thus, the presented results are applicable to a wide variety of radiation facilities around the world. Although the bare TLD-400 chip was expected to display the largest variation due to the photon angle of impact on the dosimeter, the dosimeter with the thinnest aluminum equilibrator (SNL thin equilibrated TLD-400) was determined to have the biggest differential between the impact angle with the maximum dose ( D max ) and the impact angle with the minimum dose ( D min ). However, the SNL normal equilibrated TLD-400 chip demonstrated a dramatic reduction in that differential between maximum and minimum dose angles. The reduction in this differential is one of the dominant factors in experimenters’ choice to field these dosimeters at SNL radiation facilities. The results from the PNNL (Hanford) energy-flattening field capsule are consistent with the previous publications. The differential dose responses due to the photon impact angle indicate that experimenters should strive to field their TLD-400 dosimeters in a consistent manner to avoid additional uncertainty in the measurements based on dosimeter orientation.

Adjoint radiation transport↗
DOE OSTI2020

Computational fluid dynamics analysis of char conversion in Sandia’s pressurized entrained flow reactor

Design and analysis of practical reactors utilizing solid feedstocks rely on reaction rate parameters that are typically generated in lab-scale reactors. Evaluation of the reaction rate information often relies on assumptions of uniform temperature, velocity, and species distributions in the reactor, in lieu of detailed measurements that provide local information. This assumption might be a source of substantial error, since reactor designs can impose significant inhomogeneities, leading to data misinterpretation. Spatially resolved reactor simulations help understand the key processes within the reactor and support the identification of severe variations of temperature, velocity, and species distributions. In this work, Sandia’s pressurized entrained flow reactor is modeled to identify inhomogeneities in the reaction zone. Tracer particles are tracked through the reactor to estimate the residence times and burnout ratio of introduced coal char particles in gasifying environments. The results reveal a complex mixing environment for the cool gas and particles entering the reactor along the centerline and the main high-speed hot gas reactor flow. Furthermore, the computational fluid dynamics (CFD) results show that flow asymmetries are introduced through the use of a horizontal gas pre-heating section that connects to the vertical reactor tube. Computed particle temperatures and residence times in the reactor differ substantially from the idealized plug flow conditions typically evoked in interpreting experimental measurements. Furthermore, experimental measurements and CFD analysis of heat flow through porous refractory insulation suggest that for the investigated conditions (1350 °C, <20 atm), the thermal conductivity of the insulation does not increase substantially with increasing pressure.

47 OTHER INSTRUMENTATION↗
DOE OSTI2025

Xenon–metal pair formation in UO 2 investigated using DFT + U

A recent experimental study on a spent uranium dioxide (UO 2 ) fuel sample from Belgium Reactor 3 identified a unique pair structure formed by the noble metal phase (NMP) and fission gas [xenon (Xe)] precipitate. However, the fundamental mechanism behind this structure remains unclear. The present study aims to provide an understanding of the interaction between five different metal precipitates [molybdenum (Mo), ruthenium (Ru), palladium (Pd), technetium (Tc), and rhodium (Rh)] and the Xe fission gas atoms in UO 2 , by using density functional theory (DFT) in combination with the Hubbard U correction to compute the formation energies involved. All DFT + U calculations were performed with occupation matrix control to ensure antiferromagnetic ordering of UO 2 . The calculated formation and binding energies of the Xe and solid fission products in the NMP reveal that these metal precipitates form stable pair structures with Xe. Notably, the formation energy of Xe–metal pairs is lower than that of the isolated single defects in all instances, with Pd and Mo showing the most favorable binding energy, likely accounting for the observed pair structure formation.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Isomeric yield ratios of fission products: A missing piece in reactor antineutrino summation calculations

The calculation of the spectrum of antineutrinos ($\bar{v}_e$) from a reactor is a complicated problem requiring several nuclear data and physics inputs. Many of these have been investigated thoroughly to improve calculations and properly account for uncertainties. One input which has heretofore escaped consideration is the fission-yield distribution between ground and isomeric states. Here, in this work, we explore the effect of incorporating newly evaluated isomeric yield ratios (IYR) for 43 fission products into summation calculations and identify the disproportionate importance of certain isotopes, particularly at higher energies. Our analysis indicates that updated IYRs contribute to a significant increase in the $\bar{v}_e$ spectrum around and above 7 MeV, with increases of more than 50% at higher energies. Through a detailed sensitivity study, we highlight a number of isotopes for which the IYR has a substantial effect on the $\bar{v}_e$ spectrum. This work stresses the critical role of isomeric yields in calculations of reactor $\bar{v}_e$ spectra and points to the necessity for their accurate experimental determination, especially for key fission products, in order to refine our understanding and address the observed anomalies between measured and calculated $\bar{v}_e$ spectra.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2021

Assessment of Turbulent Combustion Models for Simulating Prechamber Ignition in a Natural Gas Engine

Lean combustion is a promising strategy to increase thermal efficiency in an internal combustion engine, by exploiting a favorable specific heat ratio of the fresh mixture while simultaneously suppressing the heat losses to the cylinder wall. However, unstable ignition and slow flame propagation at fuel-lean conditions lead to large cycle-to-cycle variability and limit the high-efficiency engine operating range. Prechamber ignition is considered an effective concept to extend the lean operating limit, by providing spatially distributed ignition with multiple turbulent flame-jets and enabling a faster combustion rate compared to the conventional spark ignition approach. From a numerical modeling standpoint to date science base and available simulation tools are inadequate to properly understand and predict the combustion processes in prechamber ignited engines. In this paper, conceptually different Reynolds-averaged Navier–Stokes (RANS) combustion models widely adopted in the engine modeling community are used to simulate the ignition and combustion processes in a medium-duty natural gas engine with a prechamber spark-ignition system. Here, a flamelet-based turbulent combustion model, i.e., G-equation, and a multizone well-stirred reactor model are employed for this modeling study. Simulation results are compared with experimental data in terms of in-cylinder pressure and heat release rate. Finally, the analysis of the performance of the two models is carried out to highlight the strengths and limitations of the two evaluated approaches.

42 ENGINEERING↗
DOE OSTI2024

BiRD (BioReactorDesign) [SWR-24-35]

Numerical simulations can accelerate scale up and optimization of bioreactors. This project provides a toolbox to facilitate such numerical simulations in OpenFOAM. The tool box contains 1) mesh generations tools for several typical bio reactor types in OpenFOAM 2) Inverse modeling tools to calibrate models using available experimental data 3) post processing tools that accelerate and streamline the analysis of the numerical simulations.

Hassanaly, Malik↗
DOE OSTI2022

Irradiation of MiniFuel Targets Bearing TRISO Fuel Compacts (Status Report)

Irradiation testing of MiniFuel compacts bearing tristructural isotropic (TRISO) fuel particles was performed at Oak Ridge National Laboratory (ORNL) to support the development of Kairos Power’s (KP’s) fluoride salt–cooled high-temperature reactor concept. The fuel compacts were fabricated with TRISO fuel particles of different types—including low-enriched uranium oxide, uranium carbide (LEUCO), natural uranium oxide, uranium carbide (NUCO), and low-enriched uranium dioxide (LEUO 2 )—and inserted into MiniFuel irradiation targets. Five targets were assembled and inserted in the High Flux Isotope Reactor (HFIR) for four cycles. The data collected post-irradiation will provide experimental input to validate TRISO fuel performance models for high particle power operations. This report summarizes the completion of the HFIR irradiation, the as-irradiated numerical analysis, and the post-irradiation work performed to date. This work was performed under the Nuclear Science User Facility program.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗