SEARCH · Engineering Papers

Results for “Dynamic Procedures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS1988

Calculations of rate constants for the three-body recombination of H2 in the presence of H2

A new global potential energy hypersurface for H2 + H2 is constructed and quasiclassical trajectory calculations performed using the resonance complex theory and energy transfer mechanism to estimate the rate of three body recombination over the temperature range 100 to 5000 K. The new potential is a faithful representation of ab initio electron structure calculations, is unchanged under the operation of exchanging H atoms, and reproduces the accurate H3 potential as one H atom is pulled away. Included in the fitting procedure are geometries expected to be important when one H2 is near or above the dissociation limit. The dynamics calculations explicitly include the motion of all four atoms and are performed efficiently using a vectorized variable-stepsize integrator. The predicted rate constants are approximately a factor of two smaller than experimental estimates over a broad temperature range.

Schwenke, David W.↗

NASA NTRS1988

Hub and blade structural loads measurements of an SA349/2 helicopter

Data from 23 flight conditions, including level flights ranging from advance ratio mu = 0.14 to 0.37 and steady turning flights from advance ratio mu = 0.26 to 0.35, are presented for an Aerospatiale SA349/2 Gazelle helicopter. The data include hub loads data (for 6 of the 23 conditions), blade structural data at eleven different blade radial stations, and fuselage structural data. All dynamic data are presented as harmonic analysis coefficients (ten harmonics per rotor revolution). The data acquisition and reduction procedures are also documented. Blade structural and inertial properties are provided in addition to control system geometry and properties.

Yamauchi, Gloria K.↗

NASA NTRS1989

Small Expendable-tether Deployer System (SEDS) development status

Plans for proposed flight of the Small Expendable-tether Deployer System (SEDS) on a Delta II launch vehicle are discussed. The SEDS tether concept and mission requirements are outlined. Results are presented from calculations of the tether dynamics and computer modeling to determine tether behavior. The tether's thermal characteristics, electronics system, material, data collection procedure, payload, and orbital trace are described.

Harrison, James K.↗

NASA NTRS1990

Finite element model reduction application to parametric studies and optimization of rotorcraft structures

As a result of this work, a reduction procedure has been developed which can be applied to large finite element model of airframe type structures. This procedure, which is tailored to be used with MSC/NASTRAN finite element code, is applied to the full airframe dynamic finite element model of AH-64A Attack Helicopter. The applicability of the resulting reduced model to parametric and optimization studies is examined. Through application of the design sensitivity analysis, the viability and efficiency of this reduction technique has been demonstrated in a vibration reduction study.

Hashemi-Kia, M.↗

NASA NTRS1992

Structures research

The main objective of the structures group is to provide quality aerospace research with the Center for Aerospace Research - A NASA Center for Excellence at North Carolina Agricultural and Technical State University. The group includes dedicated faculty and students who have a proven record in the area of structures, in particular space structures. The participating faculty developed accurate mathematical models and effective computational algorithms to characterize the flexibility parameters of joint dominated beam-truss structures. Both experimental and theoretical modelling has been applied to the dynamic mode shapes and mode frequencies for a large truss system. During the past few months, the above procedures has been applied to the hypersonic transport plane model. The plane structure has been modeled as a lumped mass system by Doctor Abu-Saba while Doctor Shen applied the transfer matrix method with a piecewise continuous Timoshenko tapered beam model. Results from both procedures compare favorably with those obtained using the finite element method. These two methods are more compact and require less computer time than the finite element method. The group intends to perform experiments on structural systems including the hypersonic plane model to verify the results from the theoretical models.

Abu-Saba, Elias↗

NASA NTRS1992

Control and stabilization of nonholonomic dynamic systems

The paper establishes a theoretical framework for the control of nonholonomic dynamic systems, i.e., dynamic systems with nonintegrable constraints, with emphasis on control properties for nonholonomic systems that have no counterpart in holonomic systems. A model for nonholonomic dynamic systems is presented in terms of differential-algebraic equations defined on a phase space. A reduction procedure is carried out to obtain reduced-order state equations. Conditions for smooth asymptotic stabilization to an m-dimensional equilibrium manifold are presented. It is also demonstrated that a single equilibrium solution cannot be asymptotically stabilized using continuous state feedback. An approach using geometric phases is developed as a basis for the control of Caplygin systems.

Bloch, Anthony M.↗

NASA NTRS1994

Turbomachinery Forced Response Prediction System (FREPS): User's Manual

The turbomachinery forced response prediction system (FREPS), version 1.2, is capable of predicting the aeroelastic behavior of axial-flow turbomachinery blades. This document is meant to serve as a guide in the use of the FREPS code with specific emphasis on its use at NASA Lewis Research Center (LeRC). A detailed explanation of the aeroelastic analysis and its development is beyond the scope of this document, and may be found in the references. FREPS has been developed by the NASA LeRC Structural Dynamics Branch. The manual is divided into three major parts: an introduction, the preparation of input, and the procedure to execute FREPS. Part 1 includes a brief background on the necessity of FREPS, a description of the FREPS system, the steps needed to be taken before FREPS is executed, an example input file with instructions, presentation of the geometric conventions used, and the input/output files employed and produced by FREPS. Part 2 contains a detailed description of the command names needed to create the primary input file that is required to execute the FREPS code. Also, Part 2 has an example data file to aid the user in creating their own input files. Part 3 explains the procedures required to execute the FREPS code on the Cray Y-MP, a computer system available at the NASA LeRC.

Morel, M. R.↗

NASA NTRS1994

Color/magnitude calibration for National Aeronautics and Space Administration (NASA) standard Fixed-Head Star Trackers (FHST)

This paper characterizes and analyzes the spectral response of Ball Aerospace fixed-head star trackers, (FHST's) currently in use on some three-axis stabilized spacecraft. The FHST output is a function of the frequency and intensity of the incident light and the position of the star image in the field of view. The FHST's on board the Extreme Ultraviolet Explorer (EUVE) have had occasional problems identifying stars with a high B-V value. These problems are characterized by inaccurate intensity counts observed by the tracker. The inaccuracies are due to errors in the observed star magnitude values. These errors are unique to each individual FHST. For this reason, data were also collected and analyzed from the Upper Atmosphere Research Satellite (UARS). As a consequence of this work, the Goddard Space Flight Center (GSFC) Flight Dynamics Division (FDD) hopes to improve the attitude accuracy on these missions and to adopt better star selection procedures for catalogs.

Landis, J.↗

NASA NTRS1995

Background and principles of throttles-only flight control

There have been many cases in which the crew of a multi-engine airplane had to use engine thrust for emergency flight control. Such a procedure is very difficult, because the propulsive control forces are small, the engine response is slow, and airplane dynamics such as the phugoid and dutch roll are difficult to damp with thrust. In general, thrust increases are used to climb, thrust decreases to descend, and differential thrust is used to turn. Average speed is not significantly affected by changes in throttle setting. Pitch control is achieved because of pitching moments due to speed changes, from thrust offset, and from the vertical component of thrust. Roll control is achieved by using differential thrust to develop yaw, which, through the normal dihedral effect, causes a roll. Control power in pitch and roll tends to increase as speed decreases. Although speed is not controlled by the throttles, configuration changes are often available (lowering gear, flaps, moving center-of-gravity) to change the speed. The airplane basic stability is also a significant factor. Fuel slosh and gyroscopic moments are small influences on throttles-only control. The background and principles of throttles-only flight control are described.

Burcham, Frank W., Jr.↗

NASA NTRS1996

The Avoidance of Saturation Limits in Magnetic Bearing Systems During Transient Excitation

When a transient event, such as mass loss, occurs in a rotor/magnetic bearing system, optimal vibration control forces may exceed bearing capabilities. This will be inevitable when the mass loss is sufficiently large and a conditionally unstable dynamic system could result if the bearing characteristic become non-linear. This paper provides a controller design procedure to suppress, where possible, bearing force demands below saturation levels while maintaining vibration control. It utilizes H(sub infinity) optimization with appropriate input and output weightings. Simulation of transient behavior following mass loss from a flexible rotor is used to demonstrate the avoidance of conditional instability. A compromise between transient control force and vibration levels was achieved.

Rutland, Neil K.↗

NASA NTRS1998

Accommodating Actuator Failures in Flight Control Systems

A technique for the design of flight control systems that can accommodate a set of actuator failures is presented. As employed herein, an actuator failure is defined as any change in the parametric model of the actuator which can adversely affect actuator performance. The technique is based upon the formulation of a fixed feedback topology which ensures at least stability in the presence of the failures in the set. The fixed compensation is obtained from a loop-shaping design procedure similar to Quantitative Feedback Theory and provides stability robustness in the presence of uncertainty in the vehicle dynamics caused by the failures. System adaptation to improve performance after actuator failure(s) occurs through a static gain adjustment in the compensator followed by modification of the system prefilter. Precise identification of the vehicle dynamics is unnecessary. Application to a single-input, single-output design using a simplified model of the longitudinal dynamics of the NASA High Angle of Attack Research Vehicle is discussed. Non-real time simulations of the system including a model of the pilot demonstrate the effectiveness and limitations of the approach.

Hess, R. A.↗

NASA NTRS2001

Accuracy Assessment of Response Surface Approximations for Supersonic Turbine Design

There is a growing trend to employ CFD tools to supply the necessary information for design optimization of fluid dynamics components/systems. Such results are prone to uncertainties due to reasons including discretization. errors, incomplete convergence of computational procedures, and errors associated with physical models such as turbulence closures. Based on this type of information, gradient-based optimization algorithms often suffer from the noisy calculations, which can seriously compromise the outcome. Similar problems arise from the experimental measurements. Global optimization techniques, such as those based on the response surface (RS) concept are becoming popular in part because they can overcome some of these barriers. However, there are also fundamental issues related to such global optimization technique such as RS. For example, in high dimensional design spaces, typically only a small number of function evaluations are available due to computational and experimental costs. On the other hand, complex features of the design variables do not allow one to model the global characteristics of the design space with simple quadratic polynomials. Consequently a main challenge is to reduce the size of the region where we fit the RS, or make it more accurate in the regions where the optimum is likely to reside. Response Surface techniques using either polynomials or and Neural Network (NN) methods offer designers alternatives to conduct design optimization. The RS technique employs statistical and numerical techniques to establish the relationship between design variables and objective/constraint functions, typically using polynomials. In this study, we aim at addressing issues related to the following questions: (1) How to identify outliers associated with a given RS representation and improve the RS model via appropriate treatments? (2) How to focus on selected design data so that RS can give better performance in regions critical to design optimization? (3) How to combine NN and polynomial techniques for improving the accuracy of the RS model?

Papila, Nilay↗

NASA NTRS2018

High-Fidelity Multidisciplinary Design Optimization Methodology with Application to Rotor Blades

A multidisciplinary design optimization procedure has been developed and applied to rotorcraft simulations involving tightly-coupled, high-fidelity computational fluid dynamics and comprehensive analysis. A discretely-consistent, adjoint-based sensitivity analysis available in the fluid dynamics solver provides sensitivities arising from unsteady turbulent flows on unstructured, dynamic, overset meshes, while a complex-variable approach is used to compute structural sensitivities with respect to aerodynamic loads. The multidisciplinary sensitivity analysis is conducted through integrating the sensitivity components from each discipline of the coupled system. Accuracy of the coupled system for high-fidelity rotorcraft analysis is verified; simulation results exhibit good agreement with established solutions. A constrained gradient-based design optimization for a HART-II rotorcraft configuration is demonstrated. The computational cost for individual components of the multidisciplinary sensitivity analysis is assessed and improved.

Wang, Li↗

NASA NTRSDate not supplied

Improving the Use of Surface-Sensitive Radiances in the GMAO Hybrid-4DEnVar System

The planetary boundary layer (PBL) was designated as an incubation-class targeted observable (TO) in the 2018 Decadal Survey. As no single instrument source will provide enough information to constrain the global PBL, the assimilation of a wide range of observations in data assimilation (DA) systems will play a critical role, and GMAO has put in efforts to enhance surface-sensitive radiance assimilation. Although a vast number of microwave radiance observations are used in the GEOS global DA system, very few surface-sensitive radiances are currently used over land due to large uncertainty of land surface emissivity in the CRTM as well as cloud detection issue. Dynamically varying emissivity is retrieved from observations of window channels in the GEOS system for non-scattering FOVs and applied to sounding channel assimilation. Moreover, the original radiance bias correction is found not to work well over land, and shows drifting bias when the original emissivity sensitivity bias predictor with a dynamically varying emissivity retrieval is used. Hence, the radiance bias correction has been modified, and the quality control procedure has been adapted accordingly. Cycled experiment results show improvement in the temperature forecast at lower model levels; further refinement of this system continues.

Yanqiu Zhu↗

NASA NTRS1993

Optimization of contoured hypersonic scramjet inlets with a least-squares parabolized Navier-Stokes procedure

A new optimization procedure, in which a parabolized Navier-Stokes solver is coupled with a non-linear least-squares optimization algorithm, is applied to the design of a Mach 14, laminar two-dimensional hypersonic subscale flight inlet with an internal contraction ratio of 15:1 and a length-to-throat half-height ratio of 150:1. An automated numerical search of multiple geometric wall contours, which are defined by polynomical splines, results in an optimal geometry that yields the maximum total-pressure recovery for the compression process. Optimal inlet geometry is obtained for both inviscid and viscous flows, with the assumption that the gas is either calorically or thermally perfect. The analysis with a calorically perfect gas results in an optimized inviscid inlet design that is defined by two cubic splines and yields a mass-weighted total-pressure recovery of 0.787, which is a 23% improvement compared with the optimized shock-canceled two-ramp inlet design. Similarly, the design procedure obtains the optimized contour for a viscous calorically perfect gas to yield a mass-weighted total-pressure recovery value of 0.749. Additionally, an optimized contour for a viscous thermally perfect gas is obtained to yield a mass-weighted total-pressure recovery value of 0.768. The design methodology incorporates both complex fluid dynamic physics and optimal search techniques without an excessive compromise of computational speed; hence, this methodology is a practical technique that is applicable to optimal inlet design procedures.

Korte, J. J.↗

NASA NTRS1986

Stochastic modeling and control system designs of the NASA/MSFC Ground Facility for large space structures: The maximum entropy/optimal projection approach

In the Control Systems Division of the Systems Dynamics Laboratory of the NASA/MSFC, a Ground Facility (GF), in which the dynamics and control system concepts being considered for Large Space Structures (LSS) applications can be verified, was designed and built. One of the important aspects of the GF is to design an analytical model which will be as close to experimental data as possible so that a feasible control law can be generated. Using Hyland's Maximum Entropy/Optimal Projection Approach, a procedure was developed in which the maximum entropy principle is used for stochastic modeling and the optimal projection technique is used for a reduced-order dynamic compensator design for a high-order plant.

Hsia, Wei-Shen↗

NASA NTRS2009

The Capillary Flow Experiments Aboard the International Space Station: Increments 9-15

This report provides a summary of the experimental, analytical, and numerical results of the Capillary Flow Experiment (CFE) performed aboard the International Space Station (ISS). The experiments were conducted in space beginning with Increment 9 through Increment 16, beginning August 2004 and ending December 2007. Both primary and extra science experiments were conducted during 19 operations performed by 7 astronauts including: M. Fincke, W. McArthur, J. Williams, S. Williams, M. Lopez-Alegria, C. Anderson, and P. Whitson. CFE consists of 6 approximately 1 to 2 kg handheld experiment units designed to investigate a selection of capillary phenomena of fundamental and applied importance, such as large length scale contact line dynamics (CFE-Contact Line), critical wetting in discontinuous structures (CFE-Vane Gap), and capillary flows and passive phase separations in complex containers (CFE-Interior Corner Flow). Highly quantitative video from the simply performed flight experiments provide data helpful in benchmarking numerical methods, confirming theoretical models, and guiding new model development. In an extensive executive summary, a brief history of the experiment is reviewed before introducing the science investigated. A selection of experimental results and comparisons with both analytic and numerical predictions is given. The subsequent chapters provide additional details of the experimental and analytical methods developed and employed. These include current presentations of the state of the data reduction which we anticipate will continue throughout the year and culminate in several more publications. An extensive appendix is used to provide support material such as an experiment history, dissemination items to date (CFE publication, etc.), detailed design drawings, and crew procedures. Despite the simple nature of the experiments and procedures, many of the experimental results may be practically employed to enhance the design of spacecraft engineering systems involving capillary interface dynamics.

Jenson, Ryan M.↗

NASA NTRSDate not supplied

Computationally Efficient Frequency Domain Method for Dynamic Control Derivative Estimation with Application to Transonic Truss-Braced Wing

This paper presents a computationally efficient method for dynamic control derivative estimation technique via control surface oscillation numerical experiments. Unsteady RANS CFD simulations in FUN3D are performed to simulate the control surface oscillations with a prescribed truncated square wave containing sufficient frequencies of interest. The truncated square wave oscillation offers the computational efficiency which reduces the computational cost by almost an order of magnitude compared to a sine wave oscillation. The nonlinear effect of large control surface oscillation amplitudes creates a spillover effect whereby the frequency response at the same input frequencies contains not only the linear aerodynamic response but also nonlinear aerodynamic response. A correction procedure is developed to remove the spillover effect from the linear aerodynamic response. A frequency-domain regression is performed to estimate the dynamic control derivatives after the correction. The results generally agree with the previous results obtained from the sine wave oscillation.

Stability and Control↗