Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “DUCTILITY”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2018

Preliminary Characterization and Mechanical Performance of Additively Manufactured HT9

Laser-blown powder deposition of HT9 was performed to evaluate the feasibility of using advanced manufacturing to fabricate creep strength enhanced ferritic steels. The as-printed materials were tensile tested at room temperature, 330°C, and 550°C to provide a baseline value for the strength levels. The as-fabricated strengths are then compared with wrought materials in the published literature. The strength parameters for the as-fabricated HT9 was found to be significantly higher than that of wrought HT9 without sacrifice in ductility. Two different heat treatment cycles, deemed ACO3 and FCRD, involving two different austentizing temperatures (1065°C and 1040°C) and tempering temperatures (750°C and 760°C) were then evaluated. The heat-treated samples were also tensile tested and were found to show strength and ductility parameters which closely mimicked that of the wrought HT9 literature data. Detailed multi-scale characterization was performed at various length scales. The as-fabricated structure showed a refined martensitic structure with a significant fraction of δ-ferrite present. Closer examination using TEM showed a refined distribution of carbides (predominantly M 23 C 6 and MX or M2X), which would have precipitated during the deposition process. Upon heat treatment, it was seen that the precipitates were more homogenous and refined in the case of the specimens heat treated according to the ACO 3 cycle although there was no significant difference in the strength or the hardness results. However, the specimens heat-treated per the FCRD cycle showed significantly smaller prior austenite grains (measure and give quantitative numbers), which could result in better Charpy toughness. However, the toughness was not evaluated and will be performed in the future. In addition, possible thermos-mechanical treatments (TMT) to refine the grain structure and improve the toughness without compromising the ductility will also be evaluated in the future.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Fracture Toughness Evaluation for Sandia Mock-up Stainless Steel Canister Weldment Using Spiral Notch Torsion Fracture Toughness Test

Many radioactive materials within the nuclear fuel cycle present a significant hazard. Such materials include spent nuclear fuel, high-level waste, legacy waste and other nuclear materials that have no current outlet than storage. These materials are often held in long-term storage as an interim stage within their lifecycle. Lifecycles can include reuse or disposal. Safety and security of spent nuclear fuel (SNF) interim storage installations are very important, due to a great concentration of fission products, actinides and activation products. Stress corrosion cracking of interim storage containers has been identified as a high priority data gap by the Department of Energy. However, little has been done with regards to the canister weld material properties, including the fracture toughness, and their impact on stress corrosion, until recently from Sandia National Laboratory canister mockup program. Furthermore, because no post-weld heat treatment was required, the associated high tensile residual stress within these canister welds can drive the initiation and growth of stress corrosion cracking (SCC) cracks. Thus, the fracture mechanical property, such as fracture toughness, is an essential information to understand the canister weldment fracture resistance behavior and to support mitigation protocol development to counter SCC. In this work, we carried out fracture toughness evaluation on the received mock-up canister weldments from Sandia, using spiral notch torsion fracture test technology. The details of the weldment fracture toughness evaluation program development at ORNL are presented in this progress report. The objective of this research is to collect fracture toughness data on the mock-up canister weldment from Sandia National Laboratory. Data will be collected under quasi-static fracture loading using the Oak Ridge National Laboratory (ORNL) developed Spiral Notch Torsion Test (SNTT) technology carried out on a biaxial tension/torsion tester. These data will be used to support the ongoing SNF dry storage canister modeling activities and to address regulatory issues associated with canister container integrity and the follow-on SNF system transport reliability. SNTT has been a recent breakthrough in measuring fracture toughness for different materials, including metals, ceramics, concrete and polymers composites. Due to its high geometry constraint and unique loading condition, SNTT can be used to measure the fracture toughness with smaller specimens without concern of size effects. The application of SNTT to brittle materials has been proved to be successful. The micro-cracks induced by original notches in brittle materials could ensure crack growth in SNTT samples. Therefore, no fatigue pre-cracks are needed. The application of SNTT to the ductile material to generate valid toughness data will require a test sample with sufficient crack length to increase the sample fracture tip localized constraint. Fatigue pre-crack growth techniques are employed to introduce sharp crack front into the sample. Previously, only rough calculations were applied to estimate the compliance evolution in the SNTT crack growth process; while accurate quantitative descriptions have never been attempted. This generates an urgent need to understand the crack evolution during the SNTT fracture testing process of ductile materials. The newly developed governing equations for SNTT crack growth estimate are used to control the fatigue crack growth to effectively reaching the target crack length. The detailed SNTT approach and its estimated fracture toughness for the as-received Sandia canister weldment and the associated baseline 304 stainless steel are presented in this report. In the past SNTT technology has also been successfully applied to investigate the fracture behavior of X52 and X80 steels and the X52 welded materials used for hydrogen infrastructures. The current study in supporting Sandia SNF Dry Storage Mock-up Canister Program is the first attempt of applying SNTT to the highly ductile stainless steel and the associated weld materials. The SNTT test results indicate that SNTT method is a reliable test approach with good repeatability in applying to SS304 steel and SS304/308 weld material. The estimate JQ upon fracture for the baseline SS304 steel is at 1618 lb/in. The estimate JQ upon fracture for the SS304/308 weld from HAZ and weld specimens are 720 lb/in and 850 lb/in, respectively.

12 MANAGEMENT OF RADIOACTIVE AND NON-RADIOACTIVE W↗
DOE OSTI2018

Tensile Strength and Steam Oxidation Resistance of ODS FeCrAl Sheet and Tubes

ORNL is developing advanced low-Cr oxide dispersion strengthened (ODS) FeCrAlY alloys for accident tolerant fuel cladding, and this report describes the fabrication and characterization of a new ODS FeCrAlYZr (CrAZY) tube. This CrAZY tube was produced by successive steps of pilgering and annealing, in collaboration with a Japanese tube manufacturer. Very fine, elongated sub-grain structure in the as-received tube was consistent with the fine sub-grain structure observed for CrAZY foils fabricated by cold rolling at ORNL and led to very high tensile strength at room temperature. The elongated grain structure along the pilgering direction resulted in lower ductility in the hoop direction compared to the ductility along the tube. Similar anisotropic tensile behavior was also observed for the CrAZY foil with very limited ductility perpendicular to the rolling direction. The foil and tube were heat treated in the 850- 1100ºC range to reduce the residual stress. Recrystallization was observed at temperature as low as 900ºC, with an increasing number of recrystallized grains with increasing temperature. Exposure for 1h at 900ºC resulted in a significant improvement of the foil and tube, with a moderate decrease of strength. Atom probe tomographic analysis revealed the presence of many nano oxide precipitates but also areas with fewer precipitates due to the relatively high extrusion temperature (1100ºC). Finally, the CrAZY tube showed good oxidation resistance in steam at temperature up to 1400ºC.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Report on partially complete post-irradiation-examination of the INL samples

Ferritic-martensitic steels (NF616 and T91), and austenitic stainless steel 800H and its Grain Boundary Engineering (GBE)-treated version 800H-TMP (ThermoMechanical Processing) were irradiated in the Advanced Test Reactor (ATR) at Idaho National Laboratory (INL) and their microstructures and mechanical properties were characterized. Ferritic-martensitic steels were irradiated up to 8.16 dpa in the irradiation temperatures ranging from 241 °C to 447.5 °C. Selected 800H and 800H-TMP samples were also irradiated up to 9.12 dpa at 359°C to 431°C. Vickers hardness measurement, fractography, and microstructural characterization were performed on the selected samples in the LAMDA lab. Radiation-induced hardening of NF616 and T91 was observed in the hardness measurements which show ~37% to ~65% increases, depending on irradiation dose and irradiation temperature. Within the irradiation conditions studied in this work, samples with a higher dose had a higher hardness. All the tested alloy 800H and 800H-TMP in this work showed irradiation-hardening by ~96±7% to ~152±10%. Alloy 800HTMP tended to have slightly smaller irradiation-hardening than alloy 800H. The fractography of NF616 samples D2 (2.96 dpa at 291.5°C), D4 (5.91 dpa at 359°C), and D6 (8.16 dpa at 431°C) indicated loss of ductility with negligible necking for the sample D2, yet obvious ductile failure for samples D4 and D6. Fractography of alloy 800H samples N4 (7.27 dpa at 359°C), N5 (3.9 dpa at 451.5°C), and N6 (9.01 dpa at 431°C), and alloy 800H-TMP samples P4 (7.36 dpa at 359°C), P5 (3.95 dpa at 451.5°C), and P6 (9.12 dpa at 431°C) indicated that all samples failed in a ductile mode, with obvious necking. Dimples were observed where large Ti-containing particles were observed for the samples. TEM characterization was performed on alloy 800H (N4, N5, N6) and 800H-TMP (P4, P5 and P6). Accumulation of M23C6 precipitates at grain boundaries was observed in all samples, and the presence of Ti(C,N) precipitates at grain boundaries and in the matrix was observed in alloy 800H-TMP. M23C6 precipitates were found to have the cube-on-cube orientation relationship with the matrix. In addition, nanoscale Si-rich clusters were observed in the matrix of all samples. Atom probe tomography was conducted on the same samples, and their results are being analyzed to be integrated with the TEM results for a confident description of the clustering behavior. Due to the low irradiation temperature (up to 451.5°C), dislocation loops formed in all samples, with the density and the average size of dislocation loops in the order of 1022 – 1023 m-3 and 11.7 – 15.9 nm, respectively. The loop densities in alloy 800H were higher than that in alloy 800H-TMP under the same irradiation conditions. Further systematic data analyses, together with some complementary experiments, will be pursued for these samples to foster peer-reviewed journal article publications.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Impact of annealing at 1000°C in flowing He with low O 2 concentration on the room temperature tensile properties of Mo alloys

NorthStar is developing an accelerator-based technology to produce the medical isotope Mo-99. A previous ORNL report (ORNL/SPR-2022/2490) studied the oxidation behavior of Mo in flowing He with low oxygen content at 800°C and 1000°C and it was shown that an O 2 concentration lower than ~5ppm (μ1/1) is required to achieve acceptable oxidation rates for wrought or powder metallurgy (PM) Mo. Oxidation may also impact the mechanical properties of Mo and this report summarizes tensile results at room temperature on wrought and PM Mo before and after exposure at 1000°C in flowing He with O 2 concentration varying from 1 to 15 ppm O 2 . It was found that oxidation at 1000°C results in a significant decrease of Mo strength and ductility with brittle intergranular fracture surfaces, likely due to the segregation of oxygen at grain boundaries. For the PM Mo material, the decrease in strength and ductility was also observed after annealing in vacuum at 1000°C, indicating that the diffusion of the oxygen trapped in the material pores to grain boundaries after 20-100h at 1000°C is sufficient to embrittle the material. Finally, initial results on actual aMo and high-density disks provided by NorthStar revealed the lack of ductility of the materials due to the specific disk microstructure.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Downselection and Basic Properties of Additively Manufactured ODS Alloys

In the AMMT program the work package for development of new materials aimed to explore the advanced manufacturing techniques that are feasible for the manufacturing of advanced materials components. A merit-based feasibility study was attempted to identify an accelerated development path for dispersion strengthened (ODS) alloys by creatively combining additive manufacturing (AM) technologies with the recent advances in ODS materials and traditional manufacturing technologies. For the fiscal year, the primary tasks were focused to develop additive manufacturing (AM) and post-build processing route for oxide dispersion strengthened (ODS) ferritic (Fe-Cr alloy or 14YWT) and austenitic (Fe-Cr-Ni alloys or 316L and 316H) alloys and to perform basic microstructural and mechanical characterizations to provide feedbacks to the alloy and processing design. Further, the multi-laboratory effort created collaboratively a decision criteria matrix to evaluate and downselect the new materials processed by advanced manufacturing methods. This report is to describe the ODS alloy processing routes combining AM processes and post-build thermomechanical treatments, mechanical and microstructural characteristics of the newly developed materials, and the application results of the decision criteria matrix for the AM ODS alloys including a downselected material and feasible processing route. Key mechanical test results including tensile strength, tensile ductility, and fracture toughness data and are reported and explained. Higher strength was measured from the ferritic ODS alloys, while higher ductility and fracture toughness were measured from the austenitic ODS alloys. Many of the decision criteria were scored the same for the AM ferritic and austenitic ODS alloys, however, the generally known fact that the austenitic alloys have higher corrosion resistance and significantly better ductility. Although these scores are not significantly different to make them highly discernable, the austenitic ODS alloys were downselected to be the primary materials group in the future research on ODS materials in AMMT program.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Development of a Novel Magnesium Alloy for Thixomolding® of Automotive Components (Final Report)

Magnesium (Mg) alloy die-castings are increasingly used in the automobile industry to achieve cost effective mass reduction, especially in systems where multiple components can be integrated into a single thin wall die-casting. However, there are several component quality restrictions in thin-walled Mg die castings, including variability in dimensional accuracy, part-to-part variation in mechanical properties, and porosity in the final part, which has limited the continued growth of die-cast components in the automobile industry. An alternative to die-casting is the process of thixomolding®. While the die-casting process relies on filling a mold at high speeds with the alloy in the completely molten state, the thixomolding® process fills a mold with a thixotropic alloy in a semi-solid slurry state at a temperature between the liquidus and solidus temperatures. Ideally, the material should be ~30–65% solid rather than being completely liquid at the beginning of the injection process. Advantages of the thixomolding® process include a finer grain structure, lower porosity, improved dimensional accuracy, improved part-to part consistency, improved mechanical properties, particularly ductility in the component, the ability to reduce wall thickness for mass savings, and longer tool life due to lower process temperatures. The objective of this collaborative project between Oak Ridge National Laboratory, FCA US LLC, and Leggera Technologies was to develop one or more novel Mg alloys more suitable for thixomolding® automotive structural components than the current die-casting alloys used for this process. The primary interest was to improve ductility while maintaining tensile and fatigue strengths, as these are properties that are critical for use in body and chassis structural applications. Since good corrosion resistance is also desirable for this application, this property was also considered when evaluating promising alloy compositions. An initial evaluation of existing components thixomolded® using AM60 was performed and microstructure, and tensile properties were evaluated for the baseline alloy. Targets were established for ease of processing (characterized by the melting range defined as the difference between the liquidus and the solidus), strength, and ductility. Computational modeling was used to identify promising alloys and selected alloys were cast in laboratory scale heats. Properties measured from laboratory scale heats were used to down-select two alloys for further evaluation and component fabrication. Two alloys were prepared in industrial scale heats, cut into small pieces (chips), and thixomolding® trials were initiated. Trial components were successfully fabricated using one alloy composition, but it was concluded that further refinement of the thixomolding® process parameters are required to successfully fabricate component using second alloy. Microstructure and mechanical properties were evaluated on the material removed from the fabricated component and properties were compared to the baseline alloy. Although mechanical properties of the alloys showed improvement over the baseline alloy, it was determined that modifications to the thixomolding® process would result in better microstructure control with further improvement in properties leading to successful commercialization. A provisional patent application has already been filed on the new alloys developed as part of the project.

36 MATERIALS SCIENCE↗
DOE OSTI2023

Computationally-Guided ODS Refractory HEAs via Additive Manufacturing

This document is the final report for ARPA-E ULTIMATE project DE-AR0001422. To achieve higher efficiency turbine operation, the RTX Technology Research Center (RTRC) explored the use of additive manufacturing (AM) to produce test specimens of novel high entropy alloys (HEA) enhanced with oxide dispersion strengthening (ODS). HEAs, with multiple principal elements, offer a vast alloy design space rich with unique properties especially enhanced solid solution strengthening. ODS alloys historically are some of the best performing materials for high temperature applications. Leveraging AM enables near net shape part production and incorporation of ODS into the alloy. Density, melting temperature, and elevated temperature strength properties of several novel HEA compositions were found to meet or exceed program targets; however, obtaining sufficient room temperature ductility in these alloys proved challenging. In order to obtain an alloy with sufficient ductility, the team explored more conventional refractory alloy compositions, focusing on a niobium based alloy. This inherently ductile alloy also satisfied program metrics for cost, density, and fracture toughness. Results showed the oxide dispersions increased high temperature strength, and improved creep resistance compared to the conventional alloy, though the program creep metric was not met. Further tuning of the alloy chemistry, and optimization of the oxide dispersion, is likely required to improve creep resistance.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Report on use of Inoculants in Missile Application Alloys

This report documents the status of current inoculant research relevant to missile application alloys and MTCR control language. The information is intended to provide data on current inoculants for us determining the current state of development and identifying potential research directions. Although there has been significant scientific research into the development and synthesis of inoculants, their current availability is limited is traditional powder inoculants employed during casting processes. However, research continues the development of complex oxides, ribbon materials, high entropy alloys, and other inoculant product forms, including the use of inoculants in the melt pools produced during additive manufacturing. Research to date has focused primarily on aluminum and steel alloys with emphasis on refining grain structures and evolving equiaxed morphologies while increasing strength and castability. The primary inoculants in steel and cast irons include TiN, SiC, FeSi75, and Ce which have increased strength properties. Chief inoculants for Al alloys often include TiC, SiC, Al3Sc(x) and TiB2 to aid in precipitation and refinement. Ti and Ni alloys have fewer research activities involving inoculants, although TiN, TiB, ZrN and LaB6 (for Ti alloys) and WC, Co3FeNb2, and CrFeNb (for Ni alloys) have been used. Sic, Al2O3, Mg and Ti are key inoculants for Mg alloys. Multiple cast alloys from each of the material classes demonstrated increased strength and performance properties using inoculants, with several approaching requirements applicable to missile service environments. The continued evolution of advanced manufacturing capabilities is making it easier to produce high temperature near net shape structural materials using inoculant powders. These shapes may include the geometric shapes addressed within the MTCR (tubes and limited wall thicknesses). The use of inoculants may enable further development of high temperature alloys into near net shapes traditionally produced via casting processes due to limited ductility. This may decrease material and manufacturing costs. In addition, inoculation provides controlled kinetics and achievable chemical segregation that enables potential for far-from equilibrium thermodynamic microstructures and chemistries that could provide new metastable alloy states and subsequent properties to address co-design engineering constraints, including needs for increased strength and ductility. It is recommended that specific material combinations within these alloy classes be carefully watched as the materials evolve, with controls aimed at those having material properties above current MTCR levels. This specifically includes the use of refractory inoculants in alloys, and the application of inoculants in high strength and high temperature alloys via additive manufacturing processes, with care to link capabilities to product forms similar to the current requirements on tube geometries and material feed stocks. The continued development of nanoparticle inoculants will increase strength and ductility of high strength castings and additive manufactured metallic components. For example, adding inoculants into the casting of maraging steels and other precipitation strengthened alloys may drastically elevate mechanical properties above the control limit of current regulations.

36 MATERIALS SCIENCE↗
DOE OSTI2023

FY23 Simulation of Elastic-Plastic Failure Propagation

This memo summarizes the simulation of ductile failure propagation work conducted under the ASC project “V&V of Ductile Failure” conducted during FY 23. Physically, the failure propagation consists of crack propagation in the material. In the numerical setting—specifically in a finite element model—propagation can be accomplished through element death when critical conditions occur locally at an element that is then deleted from the simulation. The validation of the finite element models is evaluated by direct comparison between the experimental and simulation results regarding the rate of crack growth and its influence on the load-deflection response of the specimens tested. This work considers two geometries that display stable crack propagation under displacement-controlled conditions. The first geometry consists of hat specimens loaded in compression with nominally identical geometries but made with three different materials: Steel A286, Al 7075-T651 and 304L stainless steel. The three materials represent a range of ductility values that affect the response and crack propagation within the specimen. The crack induced propagates under an essentially mode-II type of deformation. The second geometry consists of a pre-cracked 304L stainless steel compact tension test specimen loaded so as to induce a mode-I deformation at the crack.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Rapid Design of Cost-Effective Refractory High Entropy Alloys Strengthened by Precipitation

Funded by the ARPA-E ULTIMATE program, this project aims to develop cost-effective refractory high entropy alloys (RHEAs) for gas turbine blades applications at 1300 degree Celsius and above. The alloy design focuses on carbides precipitation strengthening in a strong and ductile solid solution BCC matrix. The goal is to achieve balanced mechanical properties including room temperature ductility & fracture toughness and high temperature strength and creep resistance, while maintaining comparable oxidation resistance and densities to Ni-base superalloys. To accelerate alloy design, multiscale modeling including CALPHAD and first-principles density functional theory (DFT) calculations and machine learning are performed. Specifically, high throughput phase diagram calculations and screening are carried out using CALPHAD; DFT calculations are performed to predict intrinsic ductility, grain boundary strengthening potential, coefficient of thermal expansion (CTE) and temperature-dependent elastic constants. Temperature dependent yield stress, creep strain and CTE are also predicted using machine learning. Down-selected alloys are synthesized in small buttons of about 250g using arc melting for rapid evaluation on microstructure and mechanical properties before employing plasma arc melting and additive manufacturing for producing large ingots. Preliminary computational and experimental results of this project will be presented and future direction in RHEA development will be discussed.

high temperature materials↗
DOE OSTI2019

An Experimental and Numerical Analysis of the Compression of Bimetallic Cylinders

This paper investigates the upsetting of bimetallic cylinders with an aluminum alloy center and a brass ring. The influence of the center-ring shape factor and type of assembly fit (interference and clearance), and the effect of friction on the compression force and ductile damage are comprehensively analyzed by means of a combined numerical-experimental approach. Results showed that the higher the shape factor, the lower the forces required, whereas the effect of friction is especially important for cylinders with the lowest shape factors. The type of assembly fit does not influence the compression force. The accumulated ductile damage in the compression of bimetallic cylinders is higher than in single-material cylinders, and the higher the shape factor, the lower the damage for the same amount of stroke. The highest values of damaged were found to occur at the middle plane, and typically in the ring. Results also showed that an interference fit was more favorable for preventing fracture of the ring than a clearance fit. Microstructural analysis by scanning electron microscopy revealed a good agreement with the finite element predicted distribution of ductile damage.

36 MATERIALS SCIENCE↗
NASA NTRS1969

Effects of high-pressure hydrogen on storage vessel materials

Tensile tests on welded plates of three grades of steel indicate an appreciable decrease of tensile strength and ductility of notched specimens and a decrease in ductility of unnotched samples. Surface cracking, evident in unnotched specimens, is conducive to breakdown in tensile strength and ductility.

Chandler, W. T.↗
NASA NTRS1972

Mechanical properties of electron-beam-melted molybdenum and dilute molybdenum-rhenium alloys

A study of molybdenum and three dilute molybdenum-rhenium alloys was undertaken to determine the effects of rhenium on the low temperature ductility and other mechanical properties of molybdenum. Alloys containing 3.9, 5.9, and 7.7 atomic percent rhenium exhibited lower ductile-brittle transition temperatures than did the unalloyed molybdenum. The maximum improvement in the annealed condition was observed for molybdenum - 7.7 rhenium, which had a ductile-brittle transition temperature approximately 200 C (360 F) lower than that for unalloyed molybdenum. Rhenium additions also increased the low and high temperature tensile strengths and the high temperature creep strength of molybdenum. The mechanical behavior of dilute molybdenum-rhenium alloys is similar to that observed for dilute tungsten-rhenium alloys.

Klopp, W. D.↗
NASA NTRS1974

Directionally solidified composite systems under evaluation

Various types of high temperature in-situ composites were reviewed and attempts were made to determine which ones offer the most potential for future development. Some of the systems that were investigated according to the ductility of the component phases were categorized. The categories range from ductile-ductile to brittle-brittle. Examples in each category are considered with special emphasis on systems which look attractive for use in gas turbine engines. Data also touch on microstructure, mechanical properties, and process problems.

Ashbrook, R. L.↗
NASA NTRS1975

Compositional effects on mechanical properties of hafnium-carbide-strengthened molybdenum alloys

The mechanical properties of swaged rod thermomechanically processed from arc melted Mo-2Re-Hf-C alloys containing as much as 0.9-mol% HfC were evaluated. The low-temperature ductilities of these alloys were not influenced by the amount of HfC present but by the amount of Hf in excess of stoichiometry. Maximum ductility occurred at 0.2- to 0.3-at.% excess Hf. At 0.3- to 0.5-mol% HfC, alloy strength varied directly with the Mo content of extracted carbide particles, both decreasing as the amount of excess Hf increased. Additions of 2-at.% Re had little effect on strength or ductility. Tensile and creep strengths of Mo-2Re-0.7Hf-0.5C alloy equaled or exceeded those of other high strength Mo alloys.

Witzke, W. R.↗
NASA NTRS1975

A review of chromium, molybdenum, and tungsten alloys

The mechanical properties of chromium, molybdenum, and tungsten alloys are reviewed with particular emphasis on high-temperature strength and low-temperature ductility. Precipitate strengthening is highly effective at 0.4 to 0.8 times the melting temperature in these metals, with HfC being most effective in tungsten and molybdenum, and Ta(B,C) most effective in chromium. Low-temperature ductility can be improved by alloying to promote rhenium ductilizing or solution softening. The low-temperature mechanical properties of these alloys appear related to electronic interactions rather than to the usual metallurgical considerations.

Klopp, W. D.↗
NASA NTRS1975

Weldability of three forms of chemically vapor deposited tungsten

Methods were developed for electron-beam welding several forms of chemically vapor-deposited tungsten. Weld ductility was evaluated from the results of ductile-brittle transition-temperature determinations. Welds in tungsten produced from WF6 were considerably more ductile than those associated with WCl6-produced tungsten. The larger grain size of the latter material was largely responsible for this behavior.

Bryant, W. A.↗