Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Curved Structures”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
NASA NTRS1990

Numerical study of turbulent secondary flows in curved ducts

The pressure driven, fully-developed turbulent flow of an incompressible viscous fluid in curved ducts of square-section is studied numerically by making use of a finite volume method. A nonlinear Kappa - Iota model is used to represent the turbulence. The results for both straight and curved ducts are presented. For the case of fully-developed turbulent flow in straight and curved ducts, the secondary flow is characterized by an eight-vortex structure for which the computed flowfield is shown to be in good agreement with available experimental data. The introduction of moderate curvature is shown to cause a substantial increase in the strength of the secondary flow and to change the secondary flow pattern to either a double-vortex or a four-vortex configuration.

Hur, N.↗
NASA NTRS1992

Selection of LCTV operating curves for input and filter

A liquid crystal television (LCTV) SLM's phase, amplitude, and polarization all influence our selection of operating curves for input and filter. With its continuum of drive voltage, the LCTV permits grey-level control in both locations. Selection of an optimum curve depends on expected variations in signal amplitude, presence of input scene structured noise, and other factors. Using modulators obtained from a commercially available projection LCTV, and with no specifically added input noise present, we have obtained laboratory results in which the ratio of peak intensity to correlator system noise exceeded 100:1. Unfortunately, it was massively inefficient to implement the algorithm which had been developed as the abstract for this paper was submitted. Fortunately, we have quite recently developed two insights that will speed it by several orders of magnitude, and we shall report that result in the future. We will also extend the work to include clutter objects and additive input scene noise.

Juday, Richard D.↗
NASA NTRS1950

The longitudinal stability of elastic swept wings at supersonic speed

The longitudinal stability characteristics of elastic swept wings of high aspect ratio experiencing bending and torsional deformations are calculated for supersonic speed by the application of linearized lifting-surface theory. A parabolic wing deflection curve is assumed and the analysis is simplified by a number of structural approximations. The method is thereby limited in application to wings of high aspect ratio for which the root effects are small. Expressions for the lift, pitching-moment, and span load distribution characteristics are derived in terms of the elastic properties of the wing; namely, the design stress, the modulus of elasticity, the shearing modulus, and the maximum design load factor. The analysis applies to wings with leading edges swept behind the Mach lines. In all cases, however, the trailing edge is sonic or supersonic. Application of the method of analysis to wings with leading edges swept ahead of the Mach lines is discussed.

Frick, C W↗
NASA NTRS2001

Buckling Behavior of Long Anisotropic Plates Subjected to Fully Restrained Thermal Expansion

An approach for synthesizing buckling results and behavior for thin balanced and unbalanced symmetric laminates that are subjected to uniform heating or cooling and fully restrained against thermal expansion or contraction is presented. This approach uses a nondimensional analysis for infinitely long, flexurally anisotropic plates that are subjected to combined mechanical loads and is based on useful nondimensional parameters. In addition, stiffness-weighted laminate thermal-expansion parameters are derived that are used to determine critical temperatures in terms of physically intuitive mechanical buckling coefficients, and the effects of membrane orthotropy and membrane anisotropy are included. Many results are presented for some common laminates that are intended to facilitate a structural designer's transition to the use of the generic buckling design curves that are presented in the paper. Several generic buckling design curves are presented that provide physical insight into the buckling response in addition to providing useful design data. Examples are presented that demonstrate the use of the generic design curves. The analysis approach and generic results indicate the effects and characteristics of laminate thermal expansion, membrane orthotropy and anisotropy, and flexural orthotropy and anisotropy in a very general and unifying manner.

Nemeth, Michael P.↗
NASA NTRS2003

Buckling Behavior of Long Anisotropic Plates Subjected to Fully Restrained Thermal Expansion

An approach for synthesizing buckling results and behavior for thin, balanced and unbalanced symmetric laminates that are subjected to uniform heating or cooling and which are fully-restrained against thermal expansion or contraction is presented. This approach uses a nondimensional analysis for infinitely long, flexurally anisotropic plates that are subjected to combined mechanical loads and is based on useful nondimensional parameters. In addition, stiffness-weighted laminate thermal-expansion parameters are derived and used to determine critical temperature changes in terms of physically intuitive mechanical buckling coefficients. The effects of membrane orthotropy and anisotropy are included. Many results are presented for some common laminates that are intended to facilitate a structural designer's transition to the use of the generic buckling design curves that are presented in the paper. Several generic buckling design curves are presented that provide physical insight into buckling response and provide useful design data. Examples are presented that demonstrate the use of generic design curves. The analysis approach and generic results indicate the effects and characteristics of laminate thermal expansion, membrane orthotropy and anisotropy, and flexural orthotropy and anisotropy in a very general, unifying manner.

Nemeth, Michael P.↗
NASA NTRS2003

Buckling Of Long Compression-Loaded Anisotropic Plates Restrained Against Inplane Lateral and Shear Deformations

An approach for synthesizing buckling results and behavior for thin balanced and unbalanced symmetric laminates that are subjected to uniform axial compression loads and elastically restrained against inplane expansion, contraction, and shear deformation is presented. This approach uses a nondimensional analysis for infinitely long, flexurally anisotropic plates (coupling between bending and twisting) that are subjected to combined mechanical loads and is based on nondimensional parameters. In addition, nondimensional loading parameters are derived that account for the effects of the elastic inplane deformation restraints, membrane orthotropy, and membrane anisotropy on the induced prebuckling stress state. The loading parameters are used to determine buckling coefficients that include the effects of flexural orthotropy and flexural anisotropy. Many results are presented, for some selected laminates, that are intended to facilitate a structural designer's transition to the use of the generic buckling design curves that are presented and discussed in the paper. Several buckling response curves are presented that provide physical insight into the behavior for combined loads, in addition to providing useful design data. An example is presented that demonstrates the use of the generic design curves, which are applicable to a wide range of laminate constructions. The analysis approach and generic results indicate the effects and characteristics of laminate orthotropy and anisotropy in a very general and unifying manner.

Nemeth, Michael P.↗
NASA NTRS2004

Buckling Behavior of Long Anisotropic Plates Subjected to Elastically Restrained Thermal Expansion and Contraction

An approach for synthesizing buckling results for thin balanced and unbalanced symmetric laminates that are subjected to uniform heating or cooling and elastically restrained against thermal expansion or contraction is presented. This approach uses a nondimensional analysis for infinitely long, flexural anisotropic plates that are subjected to combined mechanical loads. In addition, stiffness-weighted laminate thermal-expansion parameters and compliance coefficients are derived that are used to determine critical temperatures in terms of physically intuitive mechanical-buckling coefficients. Many results are presented for some common laminates that are intended to facilitate a structural designer s transition to the use of the generic buckling design curves. Several curves that illustrate the fundamental parameters used in the analysis are presented, for nine contemporary material systems, that provide physical insight into the buckling response in addition to providing useful design data. Examples are presented that demonstrate the use of the generic design curves.

Nemeth, Michael P.↗
NASA NTRS2010

Alternative Modal Basis Selection Procedures for Nonlinear Random Response Simulation

Three procedures to guide selection of an efficient modal basis in a nonlinear random response analysis are examined. One method is based only on proper orthogonal decomposition, while the other two additionally involve smooth orthogonal decomposition. Acoustic random response problems are employed to assess the performance of the three modal basis selection approaches. A thermally post-buckled beam exhibiting snap-through behavior, a shallowly curved arch in the auto-parametric response regime and a plate structure are used as numerical test articles. The results of the three reduced-order analyses are compared with the results of the computationally taxing simulation in the physical degrees of freedom. For the cases considered, all three methods are shown to produce modal bases resulting in accurate and computationally efficient reduced-order nonlinear simulations.

Przekop, Adam↗
NASA NTRS2012

Alternative Modal Basis Selection Procedures For Reduced-Order Nonlinear Random Response Simulation

Three procedures to guide selection of an efficient modal basis in a nonlinear random response analysis are examined. One method is based only on proper orthogonal decomposition, while the other two additionally involve smooth orthogonal decomposition. Acoustic random response problems are employed to assess the performance of the three modal basis selection approaches. A thermally post-buckled beam exhibiting snap-through behavior, a shallowly curved arch in the auto-parametric response regime and a plate structure are used as numerical test articles. The results of a computationally taxing full-order analysis in physical degrees of freedom are taken as the benchmark for comparison with the results from the three reduced-order analyses. For the cases considered, all three methods are shown to produce modal bases resulting in accurate and computationally efficient reduced-order nonlinear simulations.

Przekop, Adam↗
NASA NTRS2016

Shrink Tape Technique for Heat Forming Aluminum Substrates for Thin Foil X-Ray Mirrors and the Neutron Star Interior Composition Explorer X-Ray Concentrators

Consistent improvements in the design and fabrication of thin-foil, epoxy-replicated x-ray mirrors for astronomical telescopes have yielded increasingly higher quality and more precise astrophysical data. The Neutron Star Interior Composition Explorer (NICER) x-ray timing mission optics continues this tradition and introduces design elements that promise even more accurate measurements and precise astrophysical parameters. The singly reflecting concentrators have a curved axial profile to improve photon concentration and a sturdy full shell structure for enhanced module stability. These design elements introduced the challenge of reliably forming mirror substrates at an acceptable production rate. By developing a technique using heat shrink tape to compress and conform thin aluminum mirror substrates to shaping mandrels, production rate improved with successful fabrication. The technique's efficiency was analyzed by measuring hundreds of substrate profiles postforming, performance testing completely assembled concentrators composed of every size substrate, and comparing the results to simulated fabrication scenarios. On average, the profiles were copied within 4.6 plus or minus 3.7 percent. These measurements and the overall success of NICER's optics, via ground calibration, have shown that the heat-shrink tape method is reliable, repeatable, and could be used in future missions to increase production rate and improve performance.

Balsamo, Erin↗
DOE OSTI2019

Discovery of Giant, Non-saturating Thermopower in Topological Semimetal at Quantum Limit

Thermoelectrics are promising by directly generating electricity from waste heat. However, (sub-) room-temperature thermoelectrics have been a long-standing challenge, due to the vanishing electronic entropy at low temperature. Topological materials offer a new avenue for energy harvesting applications. Recent theories predicted that topological Weyl semimetals (WSMs) at the quantum limit can lead to a non-saturating longitudinal thermopower, as well as a quantized thermoelectric Hall conductivity approaching to a universal value. Here, we experimentally demonstrate the non-saturating thermopower and the signature of quantized thermoelectric Hall conductivity in WSM tantalum phosphide (TaP). An ultrahigh longitudinal thermopower Sxx = 1.1x10 3 muV/K, along with a power factor ~500 muW/cm/K 2 , are observed ~40K. Moreover, the thermoelectric Hall conductivity develops a plateau at high-fields and low temperatures, which further collapses onto a single curve determined by universal constants. Our work highlights the unique WSM electronic structure and topological protection of Weyl nodes toward low-temperature energy harvesting applications.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
NASA NTRS1989

R-Curve Instability Calculations Of Crack Growth

Report discusses use of instability method of calculation and R-curve mathematical models to analyze growth of cracks in fracture-mechanics specimens. In case of single material and structure, such analysis sometimes simple enough to be done on pocket calculator. Where microcomputer or larger computer available, comprehensive program includes libraries of driving-force equations for various configurations and R-curve mathematical models for different materials. Author concludes instability method simple and effective and model equations studied all viable in sense at lease one of them should fit almost any applicable set of crack-growth data. Method and models constitute powerful mathematical tools for analysis of fractures.

Orange, Thomas W.↗
NASA NTRS2023

Damage Tolerance Study of Carbon Fiber/Epoxy Sandwich Structure in Support of the SLS Payload Adapter Fitting (PAF)

This study presents experimental results of impact and subsequent compression after impact (CAI) strength testing of sandwich structure representative of most of the acreage of a Payload Adaptor Fitting (PAF) that has been built at NASA’s Marshall Space Flight Center (MSFC). An instrumented drop weight tower was used to inflict different levels of impact damage to specimens. Load versus deflection of impact curves, visual damage, dent depth, damage as ascertained by thermography and cross-sectional microscopy were evaluated as part of the damage resistance of the structure. Compression After Impact (CAI) was performed to assess damage tolerance. The results show that at the amount of visual damage was highly dependent on whether the peel ply was present on the surface of the structure. The peel ply had some effect on the CAI strength values since the specimens with peel ply showed a 14% higher average CAI strength value. For all specimens tested in this study, CAI versus damage and CAI versus impact energy curves were plotted and it was found that damage size was a good indicator of CAI strength. It is suggested to use a b-basis damage tolerance curve based on damage size as a conservative measure of the load carrying capability of the sandwich structure with impact damage.

T1100/3960↗
DOE OSTI2022

Measuring the melting curve of iron at super-Earth core conditions

The discovery of more than 4500 extrasolar planets has created a need for modeling their interior structure and dynamics. Given the prominence of iron in planetary interiors, we require accurate and precise physical properties at extreme pressure and temperature. A first-order property of iron is its melting point, which is still debated for the conditions of Earth’s interior. Here, we used high-energy lasers at the National Ignition Facility and in situ x-ray diffraction to determine the melting point of iron up to 1000 gigapascals, three times the pressure of Earth’s inner core. We used this melting curve to determine the length of dynamo action during core solidification to the hexagonal close-packed (hcp) structure. We find that terrestrial exoplanets with four to six times Earth’s mass have the longest dynamos, which provide important shielding against cosmic radiation.

58 GEOSCIENCES↗
NASA NTRS1976

Meter-wavelength VLBI. III - Pulsars

Observations of pulsars, especially the Crab Nebula pulsar, made in very long baseline interferometry (VLBI) experiments are discussed. Based on a crude 144 MHz visibility curve which is consistent with a Gaussian brightness distribution, the measured visibilities at 196, 111, and 74 MHz were interpreted to yield apparent angular diameters (at half-power) of about 0.03 sec, 0.07 sec, and 0.18 sec, respectively. These sizes scale approximately as wavelength-squared, and the 74 MHz size agrees with recent observations using interplanetary scintillation techniques. The total flux densities lie on the extrapolation from higher frequencies of the pulsing flux densities. Variations in the total flux density up to 25 per cent were observed. A lack of fine structure other than the pulsar in the nebula is indicated by the simple visibility curves. The pulse shapes are similar to single-dish measurements at 196 MHz but reveal a steady, nonpulsing component at 111 MHz. The ratio of pulsing to total power was approximately equal to one-half but varied with time. It was found that four strong, low-dispersion pulsars were only slightly resolved.

Vandenberg, N. R.↗
DOE OSTI2023

In situ mechanical characterization of a single cell-cell adhesion interface under large strain

A method of measuring a stress-strain curve in a cell-cell adhesion interface, the method including: providing a structure including a first movable island supported by a first beam, a second movable island supported by a second beam, and a gap therebetween connected by a pair of cells forming a junction, the pair of cells comprising a cell-cell adhesion interface having an initial length defined by a distance between nuclei of the pair of cells; moving the second movable island with a defined displacement; determining a displacement of the first movable island based on moving the second movable island; calculating a difference between the displacement of the first movable island and the defined displacement of the second movable island based on moving the second movable island; determining an applied strain in the cell-cell adhesion interface between the pair of cells based on the difference divided by the initial length of the cell-cell adhesion interface; calculating a force between the cell-cell adhesion interface of the pair of cells based on the displacement of the first movable island; calculating a stress in the cell-cell adhesion interface between the pair of cells based on the force; and determining the stress-strain curve of the cell-cell adhesion interface between the pair of cells by plotting the calculated stress against the applied strain.

Yang, Ruiguo↗
NASA NTRS2003

Advances in Structural Integrity Analysis Methods for Aging Metallic Airframe Structures with Local Damage

Analysis methodologies for predicting fatigue-crack growth from rivet holes in panels subjected to cyclic loads and for predicting the residual strength of aluminum fuselage structures with cracks and subjected to combined internal pressure and mechanical loads are described. The fatigue-crack growth analysis methodology is based on small-crack theory and a plasticity induced crack-closure model, and the effect of a corrosive environment on crack-growth rate is included. The residual strength analysis methodology is based on the critical crack-tip-opening-angle fracture criterion that characterizes the fracture behavior of a material of interest, and a geometric and material nonlinear finite element shell analysis code that performs the structural analysis of the fuselage structure of interest. The methodologies have been verified experimentally for structures ranging from laboratory coupons to full-scale structural components. Analytical and experimental results based on these methodologies are described and compared for laboratory coupons and flat panels, small-scale pressurized shells, and full-scale curved stiffened panels. The residual strength analysis methodology is sufficiently general to include the effects of multiple-site damage on structural behavior.

fatigue-crack growth↗
NASA NTRS1994

Analysis of the early spectra and light curve of SN 1987A

Numerical modeling of supernova spectra, light curves, and hydrodynamics requires physical inputs, numerical techniques, approximations, and assumptions which must be thoroughly understood in order to study the details of supernova explosions. Here, we discuss some of these in the context of the early evolution of supernova 1987A. Gray radiation-hydrodynamics is used to calculate the bolometric light curve and the hydrodynamic evolution of the supernova. Synthetic spectra are then obtained for the resulting density and velocity structure. The spectrum calculations are performed using a special-relativistic treatment of the radiative transfer equation in the comoving frame, line blanketing by about 10(exp 5) spectral lines, and departures from local thermodynamic equilibrium (LTE) for H I, He I, Mg II, and Ca II. We find that we are able to simultaneously fit the early light curve and spectra reasonably well, using a progenitor model from Arnett (1991a), without fine-tuning the free parameters. Temperature structures and radiative equilibrium, non-LTE effects, homologous expansion, and mean opacities are discussed.

Hauschildt, Peter H.↗