Results for “Correlation coefficient” — Page 44

NASA NTRS1999

Correlation Between Geometric Similarity of Ice Shapes and the Resulting Aerodynamic Performance Degradation: A Preliminary Investigation Using WIND

Aerodynamic performance calculations were performed using WIND on ten experimental ice shapes and the corresponding ten ice shapes predicted by LEWICE 2.0. The resulting data for lift coefficient and drag coefficient are presented. The difference in aerodynamic results between the experimental ice shapes and the LEWICE ice shapes were compared to the quantitative difference in ice shape geometry presented in an earlier report. Correlations were generated to determine the geometric features which have the most effect on performance degradation. Results show that maximum lift and stall angle can be correlated to the upper horn angle and the leading edge minimum thickness. Drag coefficient can be correlated to the upper horn angle and the frequency-weighted average of the Fourier coefficients. Pitching moment correlated with the upper horn angle and to a much lesser extent to the upper and lower horn thicknesses.

Wright, William B.↗

NASA NTRS2016

Comparison of Spatial Correlation Parameters between Full and Model Scale Launch Vehicles

The current vibro-acoustic analysis tools require specific spatial correlation parameters as input to define the liftoff acoustic environment experienced by the launch vehicle. Until recently these parameters have not been very well defined. A comprehensive set of spatial correlation data were obtained during a scale model acoustic test conducted in 2014. From these spatial correlation data, several parameters were calculated: the decay coefficient, the diffuse to propagating ratio, and the angle of incidence. Spatial correlation data were also collected on the EFT-1 flight of the Delta IV vehicle which launched on December 5th, 2014. A comparison of the spatial correlation parameters from full scale and model scale data will be presented.

Kenny, Jeremy↗

NASA NTRS2002

Thermal Analysis and Correlation of the Mars Odyssey Spacecraft's Solar Array During Aerobraking Operations

The Mars Odyssey spacecraft made use of multipass aerobraking to gradually reduce its orbit period from a highly elliptical insertion orbit to its final science orbit. Aerobraking operations provided an opportunity to apply advanced thermal analysis techniques to predict the temperature of the spacecraft's solar array for each drag pass. Odyssey telemetry data was used to correlate the thermal model. The thermal analysis was tightly coupled to the flight mechanics, aerodynamics, and atmospheric modeling efforts being performed during operations. Specifically, the thermal analysis predictions required a calculation of the spacecraft's velocity relative to the atmosphere, a prediction of the atmospheric density, and a prediction of the heat transfer coefficients due to aerodynamic heating. Temperature correlations were performed by comparing predicted temperatures of the thermocouples to the actual thermocouple readings from the spacecraft. Time histories of the spacecraft relative velocity, atmospheric density, and heat transfer coefficients, calculated using flight accelerometer and quaternion data, were used to calculate the aerodynamic heating. During aerobraking operations, the correlations were used to continually update the thermal model, thus increasing confidence in the predictions. This paper describes the thermal analysis that was performed and presents the correlations to the flight data.

Dec, John A.↗

NASA NTRS1972

Liquid-phase mixing of bipropellant doublets

Experimental results of unlike doublet mixing are correlated with an analytically derived equation predicting fluid cavitation. The correlation relates the minimum orifice pressure drop required to initiate cavitation, with the system back pressure, cold flow simulant vapor pressure, and the orifice flow discharge and contraction coefficients. Stream flow instabilities are also visually correlated with the onset of cavitation and orifice discharge coefficient measurements. The influence of cavitation on the characteristic phenomenon of hydraulic flip is observed for both circular and noncircular shaped orifices. For certain intermediate orifice lengths, some noncircular shapes are shown to produce more fully developed flows (shorter recovery lengths) and therefore a more cohesive jet, which in turn yields slightly higher cold flow mixing uniformities than circular shaped orifices of equal absolute length. The particular noncircular shaped elements evaluated are shown to be more sensitive to liquid stream misimpingement than the corresponding circular orifices.

Hoehn, F. W.↗

NASA NTRS1989

Application of an efficient hybrid scheme for aeroelastic analysis of advanced propellers

An efficient 3-D hybrid scheme is applied for solving Euler equations to analyze advanced propellers. The scheme treats the spanwise direction semi-explicitly and the other two directions implicitly, without affecting the accuracy, as compared to a fully implicit scheme. This leads to a reduction in computer time and memory requirement. The calculated power coefficients for two advanced propellers, SR3 and SR7L, and various advanced ratios showed good correlation with experiment. Spanwise distribution of elemental power coefficient and steady pressure coefficient differences also showed good agreement with experiment. A study of the effect of structural flexibility on the performance of the advanced propellers showed that structural deformation due to centrifugal and aero loading should be included for better correlation.

Srivastava, R.↗

NASA NTRS1990

Application of an efficient hybrid scheme for aeroelastic analysis of advanced propellers

An efficient 3-D hybrid scheme is applied for solving Euler equations to analyze advanced propellers. The scheme treats the spanwise direction semi-explicitly and the other two directions implicitly, without affecting the accuracy, as compared to a fully implicit scheme. This leads to a reduction in computer time and memory requirement. The calculated power coefficients for two advanced propellers, SR3 and SR7L, and various advanced ratios showed good correlation with experiment. Spanwise distribution of elemental power coefficient and steady pressure coefficient differences also showed good agreement with experiment. A study of the effect of structural flexibility on the performance of the advanced propellers showed that structural deformation due to centrifugal and aero loading should be included for better correlation.

Srivastava, R.↗

NASA NTRSDate not supplied

Numerical Investigation of Heat Transfer on the NASA SIDRM Model

NASA has developed a Simulated Inter-Duct Research Model (SIDRM) to study ice crystal icing in aircraft engines. A numerical investigation has been completed using the NASA in-house code, GlennHT. For each flow condition, many different wall thermal boundary conditions were imposed. Six uniform wall temperature cases were generated, with wall temperature relative to the freestream total temperature of 0.85, 0.90, 0.95, 1.05, 1.10, and 1.15. In addition, five cases with uniform heat flux were generated. Heat fluxes were chosen to generate average wall temperatures in the range explored by the uniform wall temperature cases. Included in the uniform heat flux cases is the adiabatic case where heat flux equals zero. The results of these simulations are then used to quantify the degree to which the heat transfer coefficient depends on wall thermal boundary condition. It is seen that the heat transfer coefficient is fairly independent of wall thermal boundary condition, as expected. However, it would appear that, at least in some locations, it may be prudent to attempt to correlate a variation of heat transfer coefficient with wall thermal boundary condition.

Ice Crystal Icing↗

NASA NTRS1976

Low-perigee aerodynamic heating during orbital flight of an atmosphere Explorer

An extensive, low-perigee orbital aerodynamic heating study was undertaken in support of the Atmosphere Explorer-C Temperature Alarm. State of the art of low-density, high-speed flows, some models of the earth's atmosphere, external flow-field definition, thermodynamic and transport properties of atmospheric gases, the accommodation coefficient orbital thermal environment, and correlation of theory and measurements are discussed. Aerodynamic heating rates are determined for eight selected orbits by means of a reduced, analytical model verified by both ground test and flight data. These heating rates are compared with classical free-molecule and first-order collision regime values.

Caruso, P. S., Jr.↗

NASA NTRS1977

Boiling incipience and convective boiling of neon and nitrogen

Forced convection and subcooled boiling heat transfer data for liquid nitrogen and liquid neon were obtained in support of a design study for a 30 tesla cryomagnet cooled by forced convection of liquid neon. The cryogen data obtained over a range of system pressures, fluid flow rates, and applied heat fluxes were used to develop correlations for predicting boiling incipience and convective boiling heat transfer coefficients in uniformly heated flow channels. The accuracy of the correlating equations was then evaluated. A technique was also developed to calculate the position of boiling incipience in a uniformly heated flow channel. Comparisons made with the experimental data showed a prediction accuracy of + or - 15 percent.

Papell, S. S.↗

NASA NTRS1977

Boiling incipience and convective boiling of neon and nitrogen

Forced convection and subcooled boiling heat transfer data for liquid nitrogen and liquid neon were obtained in support of a design study for a 30 tesla cryomagnet cooled by forced convection of liquid neon. This design precludes nucleate boiling in the flow channels as they are too small to handle vapor flow. Consequently, it was necessary to determine boiling incipience under the operating conditions of the magnet system. The cryogen data obtained over a range of system pressures, fluid flow rates, and applied heat fluxes were used to develop correlations for predicting boiling incipience and convective boiling heat transfer coefficients in uniformly heated flow channels. The accuracy of the correlating equations was then evaluated. A technique was also developed to calculate the position of boiling incipience in a uniformly heated flow channel. Comparisons made with the experimental data showed a prediction accuracy of plus or minus 15 percent

Papell, S. S.↗

NASA NTRS1978

An approximate inviscid radiating flow field analysis for outer planet entry probes

An approximate computational technique has been developed for predicting inviscid, radiating flows about blunt probes entering atmospheres consisting of hydrogen and helium. The technique is rapid and versatile and is well suited for performing parametric trade studies for outer planet entries. Details of the computational technique, the thermodynamic correlations, the 58-step absorption coefficient model and the analytic shock shape equations are discussed. Good comparisons of the radiative heating computed by the approximate method and by detailed calculations are obtained.

Zoby, E. V.↗

NASA NTRS1981

Forebody drag reduction

It is shown that the mechanisms of forebody drag reduction by means of either a spike or a forward-facing jet are similar, with the maximum achievable drag reduction being of the same order. Because the jet may be a relatively cool gas, however, the forward facing jet has the additional capability of reducing the aerodynamic heating that is so severe at high Mach numbers. By means of the correlation presented, jet ejection parameters may be chosen to achieve maximum permissible forebody drag reduction. The correlation method uses a momentum coefficient that characterizes jet efflux and freestream conditions.

Pamadi, B. N.↗

NASA NTRS1982

Transonic three-dimension viscous-inviscid interaction for wing-body configuration analysis

A three-dimensional small disturbance transonic analysis code has been coupled with a three-dimensional integral boundary layer code. A scheme was developed to interact the two codes through the use of a controlling module. The resulting hybrid code does not increase the costs or computer core requirements over that of the previous capabilities of the analysis code, which used a two-dimensional boundary layer analysis to model viscous effects. Several configurations have been analyzed and results compared against both experimental data and computational results using the two-dimensional viscous model. Results indicate good agreement with experimental data when using the three-dimensional interaction scheme, with the most marked improvement in the correlations observed for wing pressure coefficient predictions in the lower surface cusp region for supercritical wings.

Waggoner, E. G.↗

NASA NTRS1989

A generalized one-dimensional computer code for turbomachinery cooling passage flow calculations

A generalized one-dimensional computer code for analyzing the flow and heat transfer in the turbomachinery cooling passages was developed. This code is capable of handling rotating cooling passages with turbulators, 180 degree turns, pin fins, finned passages, by-pass flows, tip cap impingement flows, and flow branching. The code is an extension of a one-dimensional code developed by P. Meitner. In the subject code, correlations for both heat transfer coefficient and pressure loss computations were developed to model each of the above mentioned type of coolant passages. The code has the capability of independently computing the friction factor and heat transfer coefficient on each side of a rectangular passage. Either the mass flow at the inlet to the channel or the exit plane pressure can be specified. For a specified inlet total temperature, inlet total pressure, and exit static pressure, the code computers the flow rates through the main branch and the subbranches, flow through tip cap for impingement cooling, in addition to computing the coolant pressure, temperature, and heat transfer coefficient distribution in each coolant flow branch. Predictions from the subject code for both nonrotating and rotating passages agree well with experimental data. The code was used to analyze the cooling passage of a research cooled radial rotor.

Kumar, Ganesh N.↗

NASA NTRS1989

A generalized one dimensional computer code for turbomachinery cooling passage flow calculations

A generalized one-dimensional computer code for analyzing the flow and heat transfer in the turbomachinery cooling passages was developed. This code is capable of handling rotating cooling passages with turbulators, 180 degree turns, pin fins, finned passages, by-pass flows, tip cap impingement flows, and flow branching. The code is an extension of a one-dimensional code developed by P. Meitner. In the subject code, correlations for both heat transfer coefficient and pressure loss computations were developed to model each of the above mentioned type of coolant passages. The code has the capability of independently computing the friction factor and heat transfer coefficient on each side of a rectangular passage. Either the mass flow at the inlet to the channel or the exit plane pressure can be specified. For a specified inlet total temperature, inlet total pressure, and exit static pressure, the code computers the flow rates through the main branch and the subbranches, flow through tip cap for impingement cooling, in addition to computing the coolant pressure, temperature, and heat transfer coefficient distribution in each coolant flow branch. Predictions from the subject code for both nonrotating and rotating passages agree well with experimental data. The code was used to analyze the cooling passage of a research cooled radial rotor.

Kumar, Ganesh N.↗

NASA NTRS1993

Thermal-Hydraulic-Analysis Program

ELM computer program is simple computational tool for modeling steady-state thermal hydraulics of flows of propellants through fuel-element-coolant channels in nuclear thermal rockets. Evaluates various heat-transfer-coefficient and friction-factor correlations available for turbulent pipe flow with addition of heat. Comparisons possible within one program. Machine-independent program written in FORTRAN 77.

Walton, J. T.↗

NASA NTRS1992

Registering and resampling images in STSDAS

Registering different images can be difficult, especially if the images to be registered are images at different wavelengths, where features in one image may look entirely different or be absent from the second image. Using two new packages soon to be added to the STSDAS package, REGISTER and RESAMPLE, this job is done automatically. The REGISTER package allows the user to determine the amount of translation, rotation, and/or magnification needed to make two images, spectra, or time series congruent. The methods implemented to compute the registration parameters use: a set of the pixel coordinates of the same features identified in two files, or the FITS coordinate transformation parameters in the headers of two data files, or a single feature identified as the peak of a cross-correlation between two vectors. The coefficients describing the registration are defined by the equations (for a two-dimensional image): x = a + bx + cy, y = d + ex + fy, where (X,Y) are the pixel coordinates of a feature in the reference image, (x,y) are the pixel coordinates of a feature in the secondary image, and the computed coefficients are a, b, c, d, e, and f. Results may be produced by linking the output of REGISTER to RESAMPLE in a command language procedure. The output from REGISTER and the input to RESAMPLE consists of a matrix of coefficients (a through f above) fully specifying the registration. The RESAMPLE package resamples simple vector or image data for a given amount of translation, rotation (images only), and magnification, or reflection of the science data. Specific options included are: image rotation about the FITS reference pixel; scale changes, i.e. magnification or demagnification (for images, independently on both axes); simple translation; reflection (for images, about one or both axes); and resampling and registration to a reference data set. Output from the RESAMPLE task is the resampled image which may then be displayed and compared with the reference image.

Williamson, R. L., II↗

NASA NTRS1995

Enhanced capabilities and modified users manual for axial-flow compressor conceptual design code CSPAN

Modifications made to the axial-flow compressor conceptual design code CSPAN are documented in this report. Endwall blockage and stall margin predictions were added. The loss-coefficient model was upgraded. Default correlations for rotor and stator solidity and aspect-ratio inputs and for stator-exit tangential velocity inputs were included in the code along with defaults for aerodynamic design limits. A complete description of input and output along with sample cases are included.

Glassman, Arthur J.↗