SEARCH · Engineering Papers

Results for “Composite particles”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

All sources NASA NTRS DOE OSTI

NASA NTRS2014

Aerosol Remote Sensing in Polar Regions

Multi-year sets of ground-based sun-photometer measurements conducted at 12 Arctic sites and 9 Antarctic sites were examined to determine daily mean values of aerosol optical thickness tau(lambda) at visible and near-infrared wavelengths, from which best-fit values of Ångström's exponent alpha were calculated. Analyzing these data, the monthly mean values of tau(0.50 micrometers) and alpha and the relative frequency histograms of the daily mean values of both parameters were determined for winter-spring and summer-autumn in the Arctic and for austral summer in Antarctica. The Arctic and Antarctic covariance plots of the seasonal median values of alpha versus tau(0.50 micrometers) showed: (i) a considerable increase in tau(0.50 micrometers) for the Arctic aerosol from summer to winter-spring, without marked changes in alpha; and (ii) a marked increase in tau(0.50 micrometer) passing from the Antarctic Plateau to coastal sites, whereas alpha decreased considerably due to the larger fraction of sea-salt aerosol. Good agreement was found when comparing ground-based sun-photometer measurements of tau(lambda) and alpha at Arctic and Antarctic coastal sites with Microtops measurements conducted during numerous AERONET/MAN cruises from 2006 to 2013 in three Arctic Ocean sectors and in coastal and off-shore regions of the Southern Atlantic, Pacific, and Indian Oceans, and the Antarctic Peninsula. Lidar measurements were also examined to characterize vertical profiles of the aerosol backscattering coefficient measured throughout the year at Ny-Ålesund. Satellite-based MODIS, MISR, and AATSR retrievals of tau(lambda) over large parts of the oceanic polar regions during spring and summer were in close agreement with ship-borne and coastal ground-based sun-photometer measurements. An overview of the chemical composition of mode particles is also presented, based on in-situ measurements at Arctic and Antarctic sites. Fourteen log-normal aerosol number size-distributions were defined to represent the average features of nuclei, accumulation and coarse mode particles for Arctic haze, summer background aerosol, Asian dust and boreal forest fire smoke, and for various background austral summer aerosol types at coastal and high-altitude Antarctic sites. The main columnar aerosol optical characteristics were determined for all 14 particle modes, based on in-situ measurements of the scattering and absorption coefficients. Diurnally averaged direct aerosol-induced radiative forcing and efficiency were calculated for a set of multimodal aerosol extinction models, using various Bidirectional Reflectance Distribution Function models over vegetation-covered, oceanic and snow-covered surfaces. These gave a reliable measure of the pronounced effects of aerosols on the radiation balance of the surface-atmosphere system over polar regions.

Sun-photometer measurements↗

NASA NTRS2020

Characterizing Deposits Emplaced by Cryovolcanic Plumes on Europa

In the absence of direct observations of Europa’s particle plumes, deposits left behind during eruptive events would provide the best evidence for recent geological activity, and would serve as indicators of the best places to search for ongoing activity on the icy moon. Here, we model the morphological and spectral signatures of europan plume deposits, utilizing constraints from recent Hubble Space Telescope observations as model inputs. We consider deposits emplaced by plumes that are 1 km to 300 km tall, and find that in the time between the Galileo Mission and the arrival of the Europa Clipper spacecraft, plumes that are < 7 km tall are most likely to emplace deposits that could be detected by spacecraft cameras. Deposits emplaced by larger plumes could be detected by cameras operating at visible wavelengths provided that their average particle size is sufficiently large, their porosity is high, and/or they are salt-rich. Conversely, deposits emplaced by large plumes could be easily detected by near-IR imagers regardless of porosity, or individual particle size or composition. If low-albedo deposits flanking lineated features on Europa are indeed cryoclastic mantlings, they were likely emplaced by plumes that were less than 4 km tall, and deposition could be ongoing today. Comparisons of the sizes and albedos of these deposits between the Galileo and Europa Clipper missions could shed light on the size and frequency of cryovolcanic eruptions on Europa.

Lynnae C Quick↗

NASA NTRS2011

TPSAS-NF1676L-13040-DND

We examine the feasibility of using airborne lidar data to: 1) infer CRC Convair-580 profiles of submicrometer fraction (SMF) over land (which is the fraction of aerosols with diameters less than 1 micrometer and is closely related to FMF) and 2) provide a proxy for CCN. If these initial Aerosol Extinction Aerosol Effective Radius feasibility studies prove successful, we will then apply these methodologies in subsequent studies to examine the feasibility of using CALIPSO data in a similar manner. We use data acquired by the NASA Langley Research Center airborne High Spectral Resolution Lidar (HSRL) during several recent field missions conducted by NASA, the Department of Energy, and NOAA. The airborne HSRL, which has acquired over 300 hours of data coincident with CALIPSO overpasses, measures aerosol extinction (532 nm), backscatter (532 and 1064 nm), and depolarization (532 and 1064 nm) profiles and thereby provides a dataset directly applicable to the CALIPSO measurements. During several of these field campaigns, airborne in situ measurements were acquired simultaneously within the HSRL “curtains” thereby facilitating direct correlations of the lidar observables to in situ measurements of particle size and composition, including SMF and CCN concentration. Previous studies have used simultaneous in situ measurements of SMF and Angström exponents derived from in situ scattering (Anderson et al., 2005) and remote sensing extinction (Redemann et al. 2009) measurements to build empirical relationships between these parameters. We adopt a similar approach and investigate relationships between the lidar observables, such as backscatter and extinction Angström exponents, with the coincident airborne in situ measurements of SMF and CCN concentration.

Richard Ferrare↗

NASA NTRS2020

Characterizing Deposits Emplaced by Cryovolcanic Plumes on Europa

In the absence of direct observations of Europa’s particle plumes, deposits left behind during eruptive events would provide the best evidence for recent geological activity, and would serve as indicators of the best places to search for ongoing activity on the icy moon. Here, we model the morphological and spectral signatures of europan plume deposits, utilizing constraints from recent Hubble Space Telescope observations as model inputs. We consider deposits emplaced by plumes that are 1 km to 300 km tall, and find that in the time between the Galileo Mission and the arrival of the Europa Clipper spacecraft, plumes that are <7 km tall are most likely to emplace deposits that could be detected by spacecraft cameras. Deposits emplaced by larger plumes could be detected by cameras operating at visible wavelengths provided that their average particle size is sufficiently large, their porosity is high, and/or they are salt-rich. Conversely, deposits emplaced by large plumes could be easily detected by near-IR imagers regardless of porosity, or individual particle size or composition. If low-albedo deposits flanking lineated features on Europa are indeed cryoclastic mantlings, they were likely emplaced by plumes that were <4 km tall, and deposition could be ongoing today. Comparisons of the sizes and albedos of these deposits between the Galileo and Europa Clipper missions could shed light on the size and frequency of cryovolcanic eruptions on Europa.

Lynnae C Quick↗

NASA NTRSDate not supplied

The Effects of Arcing Ejecta on Space Suit Materials from ISS RPCM Hot Mate/Demate During EVA

Onboard ISS, taking systems off-line when powering down to perform servicing on Remote Power Control Modules (RPCMs) introduces operational risk. An investigation lead by the NASA Engineering and Safety Center (NESC) was performed by a multi-center team to assess the safety of performing on-orbit replacement of RPCMs without powering down. This investigation revealed the potential for molten metal particulate generation in the event of an arcing occurrence. As RPCM replacement can be performed outside ISS during an Extra Vehicular Activity (EVA), it is necessary to assess the effects of this molten metal ejecta contact with the Extravehicular Mobility Unit (EMU) Space Suit Assembly (SSA) during an arcing event. A test was devised to mimic arcing ejecta contact with samples representing various SSA cross-sections. Four areas of the SSA were chosen for test to represent the majority of the SSA cross-sections. Testing was conducted by the University of California, Riverside that generated the molten metal particles, included varying composition, size and temperature, and dropped them onto the surface of the various SSA cross-sections. Exposed SSA materials were then evaluated for degree of damage, penetration, and thermal conductance through the cross-section by ILC Dover. Results showed that the SSA Glove is most susceptible to damage from arcing events. This data will be used to make risk management decisions for future RPCM servicing operations. This testing also demonstrated the durability of the SSA design and materials to exposure to extreme environments

Linda S Hewes↗

NASA NTRSDate not supplied

The Effects of Arcing Ejecta on Space Suit Materials from ISS RPCM Hot Mate/Demate During EVA

Linda S. Hewes↗

DOE OSTI2020

Sandwich gasification process for high-efficiency conversion of carbonaceous fuels to clean syngas with zero residual carbon discharge

The present invention discloses a gasifier and/or a gasification process that provides a long, uniform temperature zone in the gasifier, regardless of the particle size, chemical composition, and moisture content of the fuel by sandwiching a reduction zones between two oxidation zones. The gasifier and/or gasification process has a char that is more energy-dense and almost devoid of moisture that affords for an additional (or char) oxidation zone with a temperature that is higher than a first oxidation zone which is closer to a evaporation and devolatilization zone. As such, the additional (or char) oxidation zone contributes to augmenting the reduction zone temperature, thereby providing a favorable dual impact in improving syngas composition and near-complete conversion of the tar.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

DOE OSTI2022

Sandwich gasification process for high-efficiency conversion of carbonaceous fuels to clean syngas with zero residual carbon discharge

The present invention discloses a gasifier and/or a gasification process that provides a long, uniform temperature zone in the gasifier, regardless of the particle size, chemical composition, and moisture content of the fuel by sandwiching a reduction zones between two oxidation zones. The gasifier and/or gasification process has a char that is more energy-dense and almost devoid of moisture that affords for an additional (or char) oxidation zone with a temperature that is higher than a first oxidation zone which is closer to an evaporation and devolatilization zone. As such, the additional (or char) oxidation zone contributes to augmenting the reduction zone temperature, thereby providing a favorable dual impact in improving syngas composition and near-complete conversion of the tar.

Patel, Nikhil Manubhai↗

DOE OSTI2023

Sandwich gasification process for high-efficiency conversion of carbonaceous fuels to clean syngas with zero residual carbon discharge

gasifier and a gasification process provides a long, uniform temperature zone in the gasifier, regardless of the particle size, chemical composition, and moisture content of the fuel by sandwiching a reduction zones between two oxidation zones. The gasifier and gasification process produces a char that is more energy-dense and almost devoid of moisture, affording an additional (char) oxidation zone with a temperature that is higher than a first oxidation zone which is closer to an evaporation and devolatilization zone. As such, the additional (char) oxidation zone contributes to augmenting the reduction zone temperature, providing a favorable dual impact in improving syngas composition and near-complete conversion of the tar.

Patel, Nikhil Manubhai↗

DOE OSTI2024

High-Fidelity and High-Performance Computational Simulations for Rapid Design Optimization of Sulfur Thermal Energy Storage

Industrial process heating (IPH) accounts for approximately 70% of US manufacturing energy use and is primarily produced by fossil fuel combustion. Approximately 1500 TWht (approximately 60%) of IPH demand is in the temperature range of 100-300. Industrial applications in this temperature range include drying, hydrothermal processing, thermal enhanced oil recovery, food and beverage, bioethanol production, etc. Cost-effective thermal energy storage (TES) that increases the utilization of waste and renewable heat (solar, geothermal, etc.) could provide significant energy savings and reliable heat sources, decrease emissions, and increase US manufacturing competitiveness through reductions in fuel consumption. TES development has historically been dominated by technologies suitable for deployment with concentrating solar power (CSP). State-of-the-art thermal storage deployed commercially with power tower CSP plants uses a 60%/40% NaNO3/KNO3 molten salt and operates between temperatures of approximately 280 degrees Celsius and 570 degrees Celsius using a two-tank configuration. However, these nitrate salts are unsuitable for operation outside of this temperature range due to a high freezing point of approximately 220 degrees Celsius, and limits on high-temperature salt stability and corrosion resistance of containment alloys. Other materials being investigated for TES include those based on: (1) sensible energy storage (various molten salt compositions, inert solid particles, rocks or pebble beds, sulfur, water, concrete, graphite, etc.), (2) latent energy storage in materials that undergo solid-liquid phase change at relevant temperatures (organic materials for low-temperature applications, inorganic salts and/or metals for high-temperature applications), or (3) thermochemical energy storage (hydrides, hydroxides, carbonates, metal oxides, etc.). The application temperature and challenges pertaining to storage material and/or containment cost, energy density, long-term thermal and cyclic stability, and charge/discharge heat transfer effectiveness drive material selection for a given IPH or electricity generation application. Sulfur is a cheap commodity at $80/ton compared to $1100 - 1300/ton for conventional salts. When using a metric of storage cost per kWh, sulfur costs around 2-3 $/kWh. Previous sulfur TES development focused on high temperature (>600 degrees) concentrated solar power applications with sulfur encapsulated in pipes and flow of gaseous HTF (air) in the shell side. However, for lower-temperature IPH applications in the range of approximately 100-300 degrees Celsius Element 16 adopted a compact and scalable TES design with molten sulfur in the shell and HTF pipes submerged in the molten sulfur bath. The low-cost molten sulfur TES for dispatchable IPH has deployment potential for broad applications. The spatial and temporal evolution of the HTF and sulfur temperature is critical to the TES system performance, and thus detailed modeling can improve understanding of the performance and facilitate design improvements. Using high performance computing and computational fluid dynamics (CFD) a low-cost molten sulfur thermal energy storage (TES) system for industrial process heating (IPH) applications was developed. The unique challenges in CFD modeling of sulfur TES are the sharp property changes of sulfur relevant to the working temperatures. Above 159, liquid sulfur undergoes polymerization, and the viscosity of sulfur rapidly increases by several orders of magnitude between 159 degrees Celsius and 188 degrees Celsius, followed by a decrease in viscosity beyond 188 degrees Celsius due to thermal bound dissociation. In addition, various concentrations of H2S impurities can also modify sulfur viscosity. This numerical challenge is especially relevant to transient simulation of the sulfur TES charging and discharging processes as the extreme property variations limit the applicability of traditional heat transfer correlations. Transient CFD simulations including the temperature-dependent sulfur properties and geometric complexity of the TES design were used to predict the effect of natural convection during charging and discharging on the heat transfer process, sulfur temperature uniformity, charge/discharge rates, and performance of the storage devices. The CFD model was validated with experimental results for a full charge and discharge cycle. The work will show 3D and 2D simulation comparisons aimed to facilitate rapid design iterations and a machine learning based design optimization approach.

CFD↗

DOE OSTI2024

Percolating Interfacial Layers Enhance Conductivity in Polymer–Composite Electrolytes

Here, this study investigates the impact of the ceramic particle size on the bulk and interfacial ion transport properties of composite polymer electrolytes. The ceramic particles used for this study are micrometer-sized commercial lithium lanthanum titanate (LLTO) powders and LLTO nanorods (NR) prepared in the laboratory. The polymer matrices are vinylene carbonate (VEC) based single-ion-conducting (SIC) and dual-ion-conducting (DIC) polymer electrolytes. Our results reveal that the addition of LLTO NR results in improved ion transport, while the addition of commercial LLTO is ineffective or even detrimental. We ascribe these results to the formation of an interfacial polymer layer around the LLTO particles with enhanced Li + mobility and estimate the thickness of the interfacial layer to be ∼5 nm. The high surface-to-volume ratio of the LLTO NR leads to the percolation of the interfacial region at a relatively low ceramic loading of 30 wt %. This study highlights the importance of achieving percolation of the interface region (as opposed to the particles themselves) within the composite electrolyte when the interfacial layer is the enhancement mechanism.

Ock, Ji-young↗

NASA NTRS2008

Lunar Dust Effects on Spacesuit Systems: Insights from the Apollo Spacesuits

Systems and components of selected Apollo A7L/A7LB flight-article spacesuits that were worn on the lunar surface have been studied to determine the degree to which they suffered contamination, abrasion and wear or loss of function due to effects from lunar soil particles. Filter materials from the lithium hydroxide (LiOH) canisters from the Apollo Command Module were also studied to determine the amount and type of any lunar dust particles they may have captured from the spacecraft atmosphere. The specific spacesuit study materials include the outermost soft fabric layers on Apollo 12 and 17 integrated thermal micrometeorite garment assemblies and outermost fabrics on Apollo 17 extravehicular pressure gloves. In addition, the degree of surface wear in the sealed wrist rotation bearing from Apollo 16 extravehicular and intravehicular pressure gloves was evaluated and compared. Scanning electron microscope examination of the Apollo 12 T-164 woven TeflonO fabric confirms the presence of lunar soil particles and the ability of these particles to cause separation and fraying of the Teflon fibers. Optical imaging, chemical analysis and particle sampling applied to the outer fabric of the Apollo 17 spacesuit has identified Ti as a potentially useful chemical marker for comparing the amount of lunar soil retained on different areas of the spacesuit outer fabric. High-yield particle sampling from the Apollo 17 fabric surfaces using adhesive tape found 80% of particles on the fabric are lunar soil particles averaging 10.5 m in diameter, with the rest being intrinsic fabric materials or environmental contaminants. Analysis of the mineralogical composition of the lunar particles found that on a grain-count basis the particle population is dominated by plagioclase feldspar and various types of glassy particles derived mostly from soil agglutinates, with a subordinate amount of pyroxene. On a grain size basis, however, the pyroxene grains are generally a factor of 2 larger than glass and plagioclase, so conversion of the data to a modal (volume %) basis results in pyroxene becoming the modally dominant particle type with glass and plagioclase significantly less abundant. When comparisons are made to the modal composition of lunar soil at the Apollo 17 landing site, the results suggest that pyroxene particles have overall better retention on the spacesuit outer fabric compared to plagioclase and especially glass. Scanning electron microscopy revealed no measureable difference in the amount of wear and abrasion in the wrist rotation bearing of an Apollo 16 pressure glove worn only in the spacecraft and one worn only for extravehicular activity on the lunar surface. The results suggest either that the bearing prevented entry of lunar dust, or that dust was not sufficiently abrasive to damage the bearing, or both.

Christoffersen, Roy↗

NASA NTRS1993

The unusual metallic particles in Krymka LL3.0 chondrite

The composition, structure peculiarities, and possible scenario of formation of unusual metallic particles in Krymka LL3.0 are shown. In metal released from gentle crushed after removal of chondrules of Krymka LL3.0 chondrite matter, two types of unusual metallic particles were detected. The first type of particle mainly consists of coarse-grained (greater than or equal to 50 microns) kamacite and fine-grained (less than or equal to 10 microns) Ni-high (approximately 53 wt. percent) taenite. These particles have well-defined zonal structure: kamacite is in central part of particles whereas taenite is in outside and the grains of taenite form the mantle around kamacite. In the second type of particle Fe,Ni-phase contains only fine-grained Ni-rich taenite. In both particle types there are also fine-grained phosphate, troilite, and silicate. Both particle types have mostly rounded to subrounded form.

Fisenko, A. V.↗

NASA NTRS1991

The effect of TiB2 reinforcement on the mechanical properties of an Al-Cu-Li alloy-based metal-matrix composite

The addition of ceramic particles to aluminum based alloys can substantially improve mechanical properties, especially Young's modulus and room and elevated temperature strengths. However, these improvements typically occur at the expense of tensile ductility. The mechanical properties are evaluated to a metal matrix composite (MMC) consisting of an ultrahigh strength aluminum lithium alloy, Weldalite (tm) 049, reinforced with TiB2 particles produced by an in situ precipitation technique called the XD (tm) process. The results are compared to the behavior of a nonreinforced Weldalite 049 variant. It is shown that both 049 and 049-TiB2 show very attractive warm temperature properties e.g., 625 MPa yield strength at 150 C after 100 h at temperature. Weldalite 049 reinforced with a nominal 4 v pct. TiB2 shows an approx. 8 pct. increase in modulus and a good combination of strength (529 MPa UTS) and ductility (6.5 pct.) in the T3 temper. And the high ductility of Weldalite 049 in the naturally aged and underaged tempers makes the alloy a good, high strength matrix for ceramic reinforcement.

Source record↗

DOE OSTI2022

Anisotropic Thermally Conductive Composites Enabled by Acoustophoresis and Stereolithography

Opportunities to improve thermal management in electronic devices are currently hindered by processing constraints that limit thermal conductivity in polymer-matrix composites. Active patterning of filler particles is a promising route to improve conductivity while retaining processability by improving particle contact density and directing heat along optimized pathways. Here, we employ acoustic patterning to align and compact filler particles into stripes during stereolithographic 3D printing. This approach produces polymer-based composite materials with highly efficient embedded heat transport pathways which reach 95 vol% particle utilization (relative to the parallel conduction upper limit). These composites exhibit anisotropic thermal conductivity up to 300% higher than unpatterned composites, with in-plane anisotropy ratios of up to 350%. Combining this high conductivity with 3D printing enables materials with engineered heat networks that optimize transport from hot spots to heatsinks while maintaining low viscosity for fast particle patterning and for infiltration around electronic components. Finally, numerical simulations of acoustic assembly of particles with varied geometry, when compared to experimentally characterized particle packing, illuminate pathways for further improving conductivity by optimizing particle geometry for alignment and stacking of particles with maximum contact surface area.

36 MATERIALS SCIENCE↗

DOE OSTI2021

Composite fermion nonlinear sigma models

We study particle-hole symmetry at the integer quantum Hall plateau transition using composite fermion mean-field theory. Because this theory implicitly includes some electron-electron interactions, it also has applications to certain fractional quantum Hall plateau transitions. Previous work [P. Kumar et al., Phys. Rev. B 100, 235124 (2019)] using this approach showed that the diffusive quantum criticality of this transition is described by a nonlinear sigma model with topological θ = π term. This result, which holds for both the Dirac and Halperin, Lee, and Read composite fermion theories, signifies an emergent particle-hole (reflection) symmetry of the integer (fractional) quantum Hall transition. Here we consider the stability of this result to various particle-hole symmetry-violating perturbations. In the presence of quenched disorder that preserves particle-hole symmetry, we find that finite longitudinal conductivity at this transition requires the vanishing of a symmetry-violating composite fermion effective mass, which if present would generally lead to θ ≠ π and a corresponding violation of particle-hole symmetric electrical transport σ xy ≠ $\frac1{2}$$\frac{e^2}{h}$ . When the disorder does not preserve particle-hole symmetry, we find that θ can vary continuously within the diffusive regime. Our results call for further study of the universality of the quantum Hall plateau transition.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

DOE OSTI2023

Review of Recent Progress in Plasma-Facing Material Joints and Composites in the FRONTIER U.S.-Japan Collaboration

The plasma-facing components (PFCs) of future fusion reactors will have intricate structures and require multiple materials because no one material can simultaneously satisfy all the requirements of the component. The dissimilar material joints in PFCs must withstand extreme thermal and stress gradients under neutron irradiation. The Fusion Research Oriented to Neutron Irradiation and Tritium Behavior at Material Interfaces (FRONTIER) U.S.-Japan collaboration seeks to explore and explain the behavior of internal solid interfaces in PFCs under neutron irradiation. The first step of the collaboration was to identify the leading PFCs that should be studied further and prepare them for the next step, which will include neutron irradiation. Different strategies for material development are being pursued worldwide to produce robust PFCs. Here, in this work, an overview is presented of some of the most promising materials in the areas of copper alloys, tungsten-copper composites, tungsten-steel composites, additively manufactured tungsten, particle-reinforced tungsten, and tungsten and SiC fiber composites. Each material’s fabrication and benefits are described, and some discussion of remaining questions is given.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

NASA NTRS1977

Metallic phases in the Luna 24 soil samples

The metal and sulfide phases in the Luna 24 soil samples were studied with the optical microscope and the electron microprobe. The compositions of the metal particles fall into three groups based on their Ni and Co contents: (1) Samples of meteoritic composition which have undergone metamorphism on the lunar surface. (2) Samples of submeteoritic, low Ni and low Co contents, including most of the metal particles observed. These particles are contained in glass and agglutinate particles and were probably formed by the mixing of meteoritic metal with lunar metal produced by the reduction of silicates during shock-impact. (3) Samples of high-CO content probably formed by mixing of meteoritic material with high-Co metal from the mare basalt or by fractional crystallization from a metal silicate melt. The sulfide minerals were also studied. These are almost pure FeS, and crystallized from a late stage liquid in the mare basalt. Three high-Ni sulfides were also found in the glass phase of agglutinates.

Friel, J. J.↗