Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Chemical initiation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Rapid AI-based Dissection of Ashes using Raman and XRF Spectroscopy (RADAR-X)

Waste-to-energy (WTE) facilities incinerate ~35 million tons of municipal solid waste annually in the United States. The incineration process reduces the mass and the volume of the waste fraction by over 75 and 95%, respectively. The fraction left after incineration remains as ash residues and is referred to as WTE ash, compromising of bottom and fly ash. In the United States, ~10 million tons of WTE ashes are generated annually and predominantly landfilled because of the lack of secondary end-use pathways. This incurs a significant financial burden (landfilling costs) on U.S. WTE facilities and also results in the loss of materials to the landfill. The primary objective of this research is to understand better the elemental and mineralogical composition of WTE ashes from diverse origins and find composition dependent upcycling pathways for diverting these ashes from landfills. This primary objective was addressed through three research tasks –(Task I) An AI-led Multi-Modal Approach for Compositional Analysis, (Task II) Developing a Dissolution-Based Test for Real Time Analysis, and (Task III) Establishing composition-dependent end uses. The chemical composition of WTE ash is dependent on two factors, i.e., the input waste composition and the operational parameters of a WTE facility (combustion conditions). Amongst these two factors, the input waste composition will likely show spatial and temporal variation. As a result, the chemical composition of WTE ash will also fluctuate. To understand the spatial and temporal variation in WTE ash composition, in Task I, we collected 128 ash samples (62 bottom ash and 66 fly ash samples) from 11 WTE facilities located in 11 U.S. states and characterized them via X-ray Fluorescence, powder X-ray Diffraction, and Raman Spectroscopy. The findings from this extensive characterization work indicated that the key elements in WTE fly ashes are Ca, Cl (greater than 10 wt. %), Si, S, K, Zn ( between 1 and 10 wt. %), Mg, Al, P, Ti, Fe, Cu, Br, and Pb (between 0.1 and 1 wt. %). Similarly, the key elements in WTE bottom ash fraction finer than 45μm are Ca (greater than 10 wt. %), Mg, Al, Si, S, Cl, K, Ti, Fe, Zn (between 1 and 10 wt. %), P, V, Cr, Mn, Cu, Br, and Pb (between 0.1 and 1 wt. %). Here, we note that the dominant fraction of WTE bottom ash is the coarse fraction. The coarse WTE bottom ash fraction (rich in silicon) was not characterized in this study because of excessive grinding requirements and their unsuitability as a supplementary cementitious material due to their coarse nature. The elements in WTE bottom ashes are present as calcite, anhydrite, vaterite, hydroxyapatite, quartz, bassanite, gehlenite, akermanite, hydrocalumite, and portlandite. Similarly, the mineralogical species present in WTE fly ashes are calcium chloride hydroxide, halite, calcite, anhydrite, sylvite, hydrocalumite, vaterite, hannebachite, quartz, and bassanite. Temporal variation in ash composition may also result in significant fluctuations in chemical compositions. Therefore, a WTE facility may need to monitor the ash composition (elemental and mineralogical composition) in real time. In Task I, we evaluated the possibility of using a portable X-ray fluorescence (XRF) spectrometer to monitor the elemental composition in real-time. Specifically, we collected XRF data on identical specimens via a portable XRF spectrometer (low-end) and a lab-based benchtop XRF spectrometer (high-end). The collected data was used to train an A.I. algorithm (portable XRF data as an input and benchtop XRF data as an output) to predict accurate elemental composition using portable XRF data. Finally, we developed a 2-minute photobleaching protocol to monitor the mineralogical characteristics of WTE ashes via Raman spectroscopy. Overall, the activities in Task I improved our understanding of ash composition and developed techniques to monitor elemental and mineralogical composition in near real-time. Based on the findings of Task I, we find that WTE ashes exhibit wide variability in mineralogy. For ICP-based elemental analysis, all the mineralogical species in WTE ashes must be brought into solution. This is traditionally accomplished with acid digestion using a combination of multiple acids. However, acid digestion with multiple acids is time-consuming and often fails to ensure complete digestion of the ash matrix. To address this limitation, in Task II, we developed an alkali-fusion-based digestion protocol using a combination of lithium tetraborate, lithium metaborate, and their combinations as possible alkali fluxes for digesting WTE ashes entirely and rapidly. The validity of the developed method was evaluated on two standard ash specimens, i.e., SRM 1633c coal fly ash and BCR-176R incineration fly ash specimen. The findings suggest that the developed protocol can ensure complete digestion of elements such as Al, Ba, Ca, Cr, Cu, Mg, Mn, P, Sr, V, Zn, Be, K, and rare earth elements. The recent changes in the energy market towards renewables and increased metal recycling have resulted in reduced supplies of supplementary cementitious materials (coal fly ash and slag). Therefore, in Task III, we evaluated the possibility of employing WTE ashes as SCMs. As the chemical composition of WTE ashes varies temporally (on an hourly basis), there was also a need to develop tests that can evaluate the suitability of material to act as supplementary cementitious material rapidly, i.e., in a few minutes. Therefore, in Task II, we also developed a rapid test to assess the suitability of a material to act as an SCM in 5 minutes. This represents a significant advance over the state-of-the-art R 3 test, which takes ~144 hours. This test was initially validated on amorphous aluminosilicates, such as calcined clays, and could be extended to evaluate other industrial by-products, such as WTE ashes. In Task III, we evaluated the possibility of employing WTE ashes for two applications, i.e., as an SCM and a lime substitute for clay stabilization. The findings from Task I indicated that WTE ashes are enriched in chlorine and, therefore, cannot be used directly as an SCM due to corrosion-related risks and altered hydration kinetics. Accordingly, we developed an ash treatment protocol to reduce the solubility of chlorine-containing species in WTE ashes. The developed treatment protocol also immobilized lead in certain mineral forms. As a result of the treatment, WTE ashes can be used as SCMs without any corrosion or heavy metal leaching concerns. The second application examined in this study was clay stabilization. WTE ashes are calcium-rich and can be an adequate lime replacement for clay stabilization. Our findings reveal that the sum of the concentrations of Ca(OH) 2 and CaClOH controls the clay stabilization capability of WTE ashes. In summary, in this work, we evaluated the elemental and mineralogical characteristics of U.S. WTE ashes from diverse origins and developed tests to evaluate the chemical characteristics of these ashes in real time through a portable XRF and a benchtop Raman spectrometer. Based on the chemical characteristics of these ashes, we developed an ash treatment process to enable the use of WTE ashes as an SCM and also evaluated the possibility of employing these ashes for clay stabilization. Overall, the findings from this work enables the diversion of WTE ashes from landfills for multiple end-uses, i.e., as an SCM or a lime substitute for clay stabilization.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Chemical pumps and flexible sheets spontaneously form self-regulating oscillators in solution

The synchronization of self-oscillating systems is vital to various biological functions, from the coordinated contraction of heart muscle to the self-organization of slime molds. Through modeling, we design bioinspired materials systems that spontaneously form shape-changing self-oscillators, which communicate to synchronize both their temporal and spatial behavior. Here, catalytic reactions at the bottom of a fluid-filled chamber and on mobile, flexible sheets generate the energy to “pump” the surrounding fluid, which also transports the immersed sheets. The sheets exert a force on the fluid that modifies the flow, which in turn affects the shape and movement of the flexible sheets. This feedback enables a single coated (active) and even an uncoated (passive) sheet to undergo self-oscillation, displaying different oscillatory modes with increases in the catalytic reaction rate. Two sheets (active or passive) introduce excluded volume, steric interactions. This distinctive combination of the hydrodynamic, fluid–structure, and steric interactions causes the sheets to form coupled oscillators, whose motion is synchronized in time and space. We develop a heuristic model that rationalizes this behavior. These coupled self-oscillators exhibit rich and tunable phase dynamics, which depends on the sheets’ initial placement, coverage by catalyst and relative size. Moreover, through variations in the reactant concentration, the system can switch between the different oscillatory modes. This breadth of dynamic behavior expands the functionality of the coupled oscillators, enabling soft robots to display a variety of self-sustained, self-regulating moves.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A new paradigm in electron microscopy: Automated microstructure analysis utilizing a dynamic segmentation convolutional neutral network

Over the past half century, the transmission electron microscope enabled insight into the fundamental arrangements and structures of materials. State-of-the-art electron microscopes can acquire large image datasets across multiple imaging modalities. However, the manual annotation process for feature or defect quantification may not be feasible with the modern microscope. Convolutional neural networks emerged to characterize individual microstructural features from an image in a cost-effective, consistent manner. However, many of these neural network approaches rely on thousands to hundreds of thousands of manual annotations of each feature type across hundreds of images to train the network for adequate performance. This work focused on the development and application of a pixel-wise defect detection machine-learning dynamic segmentation convolutional neural network with associated automated acquisition and postprocessing to identify microstructural features rapidly and quantitatively from a small initial dataset incorporating multiple imaging modes. The approach was demonstrated for characterization of superalloy 718 from both single image acquisition on multiple detectors to in-situ evolution captured with a single detector on a standard desktop computer to demonstrate the low barrier to entry required for widespread adoption. Pixel-by-pixel class identification was excellent with strong identification of chemically distinct phases, structurally distinct phases, and defect structures, thus demonstrating the new paradigm of machine learning-assisted characterization.

36 MATERIALS SCIENCE↗
DOE OSTI2024

Tailoring Pore Architecture and Heteroatom Functionality of Polymeric Waste-Derived Nanoporous Carbon for CO 2 Capture Applications

This study proposes upcycling polymeric waste, i.e., waste floral foam, into high-performance nanoporous carbon that efficiently captures CO 2 . This paper presents strategies for improving the properties of nanoporous carbon, which aid in a superior CO 2 capture performance. Initially, pristine nanoporous carbon was produced from waste floral foam using various KOH impregnation ratios. The nanoporous carbon with a 1:2 (waste floral foam:KOH) ratio exhibiting optimal CO 2 capture capability was further advanced through single and dual atom doping. The doping of N and codoping of N,S atoms into the nanoporous carbon altered its textural and surface chemical properties, making them efficient for CO 2 capture. Comparative CO 2 capture studies of pristine nanoporous carbon (NC-x), N-doped nanoporous carbon (N-NC2), and N,S-codoped nanoporous carbon (N,S-NC2) demonstrate the superiority of N-doping. N-doped nanoporous carbon exhibited the largest ultramicroporosity (0.3100 cm3/g, 63.43%) and highest heteroatom content (34.94 atomic %), contributing to its enhanced CO 2 capture capability (4.54 mmol/g). Finally, implementing the “waste-to-depollution” approach, this research lays the groundwork for producing low-cost, environmentally friendly nanoporous carbon with remarkable CO 2 capture attributes.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2025

Stable-Cycling Sustainable Na-Ion Batteries with Olivine Iron Phosphate Cathode in an Ether Electrolyte

Sustainable batteries using nontoxic, earth-abundant, and low-cost materials are key to decarbonization. Olivine NaFePO 4 fulfills these criteria, is attractive for Na-ion batteries, and can be derived from LiFePO 4 recycled from Li-ion battery wastes. Critical knowledge is needed for transforming LiFePO 4 to NaFePO 4 to enable such a sustainable, green engineering path toward high-performance Na-ion batteries. Herein, we report on the development of a stable-cycling, sustainable olivine iron phosphate-based Na-ion battery empowered by an improved understanding of materials transformation and electrolyte chemistry. First, we found that the conventional carbonate electrolyte with fluoroethylene carbonate additive causes an additional plateau (~2.4 V) at the end of the discharge process of the FePO 4 ||Na metal cell, leading to lower initial discharge capacity and voltage. This result shows that the voltage profile is influenced by not only intrinsic materials phase transformation during battery cycling but also the electrolyte additives and interphases formed. With the 1 M NaPF 6 diglyme electrolyte, we achieved an excellent capacity retention of 96% and 98% after 500 cycles at 1 and 5 C, respectively. Second, we chemically sodiated FePO 4 to form single-phase Na 0.9 FePO 4 . Na 0.9 FePO 4 ||hard carbon full cells demonstrated a remarkable capacity retention of ~84% at 3 and 5 C after 1000 cycles. The successful implementation of hard carbon, which can be derived from biomass waste, will further improve the sustainability of energy storage technologies. Our research demonstrates that electrolyte chemistry influences the voltage profile of phase-changing electrodes and provides effective electrolyte and full-cell design solutions for stable-cycling NaFePO 4 .

36 MATERIALS SCIENCE↗
DOE OSTI2021

Performance of Embedded Sensors in 3D Printed SiC

This report summarizes recent advances in embedding sensors in 3D printed silicon carbide (SiC) ceramic components under the Transformational Challenge Reactor (TCR) program. The additive manufacturing technologies developed under this program will enable fabrication of complex structures with embedded fuels and sensors. The sensors will be capable of characterizing fuel performance using spatially distributed measurements at the most strategic locations that would be otherwise inaccessible using conventional manufacturing techniques. While previous programmatic updates describe initial concepts for embedding sensors, materials selection, and initial characterization of the embedded sensors, the technology requires further demonstration, and quality-significant procedures must be established before the embedding technology is ready for adoption by industry. To this end, this report describes the most effective techniques that have been used to embed functional sensors in 3D printed components using a combination of binder-jet additive manufacturing and chemical vapor infiltration (CVI). A detailed procedure describes each step in the process and is available upon request. Molybdenum (Mo)-sheathed thermocouples have been successfully embedded in complex SiC components, and temperatures were monitored in situ during the embedding process. Post-embedding measurements showed no significant hysteresis, and characterization of the interface revealed qualitatively strong bonding around the entire perimeter of the sensor sheath. Distributed fiber-optic temperature sensors were able to briefly measure temperature profiles during CVI, but they ultimately failed prior to completion of the CVI run. The failure appears to be related to the fiber coating at temperatures close to 1,000°C. Future work will focus on irradiation testing of embedded thermocouples and other sheathed electrical sensors, as well as the identification of fiber-optic sensor coatings that can survive CVI.

42 ENGINEERING↗
DOE OSTI2022

Combinatorial Cu-Ni Alloy Thin-Film Catalysts for Layer Number Control in Chemical Vapor-Deposited Graphene

We synthesized a combinatorial library of CuxNi1−x alloy thin films via co-sputtering from Cu and Ni targets to catalyze graphene chemical vapor deposition. The alloy morphology, composition, and microstructure were characterized via scanning electron microscopy (SEM), energy dispersive x-ray spectroscopy (EDS), and X-ray diffraction (XRD), respectively. Subsequently, the CuxNi1−x alloy thin films were used to grow graphene in a CH4-Ar-H2 ambient at atmospheric pressure. The underlying rationale is to adjust the CuxNi1−x composition to control the graphene. Energy dispersive x-ray spectroscopy (EDS) analysis revealed that a continuous gradient of CuxNi1−x (25 at. % < x < 83 at.%) was initially achieved across the 100 mm diameter substrate (~0.9%/mm composition gradient). The XRD spectra confirmed a solid solution was realized and the face-centered cubic lattice parameter varied from ~3.52 to 3.58 A˙, consistent with the measured composition gradient, assuming Vegard’s law. Optical microscopy and Raman analysis of the graphene layers suggest single layer growth occurs with x > 69 at.%, bilayer growth dominates from 48 at.% < x < 69 at.%, and multilayer (≥3) growth occurs for x < 48 at.%, where x is the Cu concentration. Finally, a large area of bi-layer graphene was grown via a CuxNi1−x catalyst with optimized catalyst composition and growth temperature.

2D materials↗
DOE OSTI2022

Chemical kinetic interactions of NO with a multi-component gasoline surrogate: Experiments and modeling

Here this work reports an experimental and modeling study on the chemical kinetic interactions of NO with a multi-component gasoline surrogate, namely PACE-20, using a twin-piston rapid compression machine at a stochiometric fuel loading with 20% EGR (exhaust gas recirculation) by mass, pressures of 20 and 40 bar, and temperatures from 700 to 930 K. Five NO concentrations are investigated, namely 0, 20, 50, 70 and 150 ppm, where NO addition effects are characterized through changes in PACE-20 ignition reactivity and heat release characteristics. Experiments indicate that within the low-temperature regime, NO promotes low-temperature heat release rate and main ignition reactivity at low addition levels, with saturation or even inhibiting effects observed at >50 ppm NO addition, while within the NTC/intermediate-temperature regime, adding NO only promotes reactivity. A recently updated, detailed chemical kinetic model with chemistry specific to NOx/hydrocarbons interaction incorporated is used to simulate the experiments, and reasonable agreement is obtained. In-depth sensitivity and rate of production analyses are further performed. The results indicate that NO interacts with PACE-20 via two types of interaction: (a) direct interactions between NO and PACE-20 derivatives, primarily through NO+HO 2 ↔NO 2 +OH and RO 2 +NO↔RO+NO 2 , and (b) indirect interactions between PACE-20 derivatives and NO 2 produced from the direct interactions, primarily through R+NO 2 ↔RO+NO. The observed NO inhibiting effect at low temperatures and 150 ppm NO addition is attributed to the lack of HO 2 radicals to sustain NO consumption via NO+HO 2 ↔NO 2 +OH, and the take-up of inhibiting pathways via RO 2 +NO↔RO+NO 2 . The results also indicate that even with the presence of multiple fuel components, NOx/hydrocarbons interactions are highly selective, and are mainly initiated by the interactions between NO and RO 2 radicals from cyclopentane and ethanol, as well as between NO 2 and R radicals from toluene, 1,2,4-trimethylbenzene and 1-hexene. Further studies on these interactive reactions are therefore highly recommended.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2023

Triplet Fusion Upconversion for Photocuring 3D-Printed Particle-Reinforced Composite Networks

High energy photons (λ < 400 nm) are frequently used to initiate free radical polymerizations to form polymer networks, but are only effective for transparent objects. This phenomenon poses a major challenge to additive manufacturing of particle-reinforced composite networks since deep light penetration of short-wavelength photons limits the homogeneous modification of physicochemical and mechanical properties. Herein, the unconventional, yet versatile, multiexciton process of triplet–triplet annihilation upconversion (TTA-UC) is employed for curing opaque hydrogel composites created by direct-ink-write (DIW) 3D printing. TTA-UC converts low energy red light (λ max = 660 nm) for deep penetration into higher-energy blue light to initiate free radical polymerizations within opaque objects. Further, as proof-of-principle, hydrogels containing up to 15 wt.% TiO 2 filler particles and doped with TTA-UC chromophores are readily cured with red light, while composites without the chromophores and TiO 2 loadings as little as 1–2 wt.% remain uncured. Importantly, this method has wide potential to modify the chemical and mechanical properties of complex DIW 3D-printed composite polymer networks.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Coupling reduced‐order modeling and coarse‐grained CFD‐DEM to accelerate coal gasifier simulation and optimization

Abstract High fidelity three‐dimensional (3‐D) numerical simulations of commercial‐scale coal gasifiers are very time consuming and expensive. This article proposes a reduced‐order modeling approach that uses quasi one‐dimensional (1‐D) CFD–DEM simulation results to serve as an accurate initial condition for the 3‐D simulation, which significantly shortens the physical time from several hours to minutes to achieve steady states. The 3‐D simulation employs a previously validated coarse‐grained CFD‐DEM approach, which further accelerates the simulation. Both 1‐D and 3‐D simulations adopt a particle shrinkage scheme to correctly account for the particle volume change due to chemical reaction and thus provides an accurate bed height. Comparison with available experimental measurements of the bed temperature and synthesis gas composition is used to validate the simulation. The final syngas composition and flowrates are strongly affected by the fuel or gasification agent rate and process operating conditions as expected. This approach is then used to optimize two important operating conditions (air and steam flows) to achieve specific gasifier performance goals for the production of Fischer–Tropsch synthesis gas and production of fuel gas for gas turbines.

Yu, Jia↗
DOE OSTI2021

Operational Limits of Redox Metal Oxides Performing Thermochemical Water Splitting

Solar thermochemical hydrogen production is an attractive technology that stores intermittent solar energy in the form of chemical bonds. Efficient operation requires the identification of a redox-active metal oxide (MO x ) material that can achieve high conversion of water to hydrogen at minimal energy input. Water splitting occurs by consecutive reduction and reoxidation reactions of MO x . MO x is reduced to MO x-δ and, in the second step, is reoxidized by water recovering the initial MO x and generate H 2 . The material must reduce at temperatures achievable in concentrated solar receiver/reactors, while maintaining a thermodynamic driving force to split water. At equilibrium, extent of reduction depends on temperature and oxygen partial pressure, and in this analysis, a set of thermodynamic properties, namely, enthalpy and entropy of oxygen vacancy formation, is sufficient to represent MO x . Herein, a method to easily classify materials based on these thermodynamic properties under any condition of oxygen partial pressure and temperature is presented. This method is based on fundamental thermodynamic principles and is applicable for any redox material with known thermodynamic properties. Despite the simplicity of the method, it is believed that this analysis will support future research in targeting thermodynamic properties of redox-active metal oxides.

water splitting↗
DOE OSTI2020

Radiolytic degradation of formic acid and formate in aqueous solution: modeling the final stages of organic mineralization under advanced oxidation process conditions

The successful use of advanced oxidation processes to treat aqueous solutions containing undesirable organic species requires the degradation of these species to lower molecular weight, lower hazard compounds. Safe application of this technology requires a thorough understanding of the mechanisms of degradation. These oxidative transformations are mainly initiated by the reactions of reactive oxygen species, particularly hydroxyl radicals. These react with organic molecules to generate carbon-centered radicals. In the presence of dissolved oxygen, the carbon-centered radicals are next converted to peroxyl radicals, which then decay to lower molecular weight species by multiple mechanistic pathways. Formic acid and its conjugate base formate are the last stable chemical species produced immediately before the complete mineralization of any organic molecule undergoing oxidative degradation in aqueous solution. Once understood, the radical-induced chemistry of formic acid/formate under these conditions has wide applicability in all advanced oxidation technologies. To develop this quantitative knowledge, here we have performed a series of 60 Co gamma irradiation studies on aqueous formic acid/formate over different pH and solution conditions. The measured species concentration changes, as a function of applied dose, are compared with the predictions of a kinetic computer model constructed from literature reactions and reported rate coefficients. The excellent agreement found between the results and modeling gives confidence in the mechanism presented here and provide the first complete computer model for the radiolytic degradation of formic acid in water.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

A DFT-based kinetic Monte Carlo simulation of multiphase oxide-metal thin film growth

Functional thin films of nanoscale metal pillars in oxide or nitride matrices known as vertically aligned nanocomposite (VAN) have gained much interest owing to their unique strain-coupled and highly anisotropic properties. So far, the deposition of these films has been explored mostly experimentally. In this work, a density functional theory (DFT)-based kinetic Monte Carlo simulation model using Bortz–Kalos–Lebowitz algorithm was developed to understand the growth of VAN films deposited by pulsed laser technique on mismatching substrates. The model has been parameterized and applied to understand the kinetics of growth thin films consisting of Au pillars in CeO2 matrix deposited on SrTiO3 substrates. The effects of pulsed laser deposition (PLD) conditions including the pulse frequency, deposition flux, and substrate temperature were explored. The simulations indicate that the Au pillar size and shape exhibit significant dependence on the PLD conditions. Namely, increasing the temperature increases the average pillar size and lowers the pillar density, and vice versa. In addition, the simulations revealed that increasing the deposition rate results in lowering the average pillar size and increasing the density. Particularly, the DFT results suggest that Au pillar size can be tuned during the initial growth of the first monolayer due to the significantly low activation barrier. Our analysis showed that the relationship between the average pillar size and pillar density is influenced by the kinetics. Furthermore, autocorrelation analysis showed that pillars self-organize in quasi-ordered patterns at certain windows of the deposition conditions, which is attributed to the complex nature of the chemical interactions in the system, the kinetics, and the deposition parameters.

Physics↗
DOE OSTI2023

Atomistic simulations for investigation of substrate effects on lipid in-source fragmentation in secondary ion mass spectrometry

In beam-based ionization methods, the substrate plays an important role on the desorption mechanism of molecules from surfaces. Both the specific orientation that a molecule adopts at a surface and the strength of the molecule-surface interaction can greatly influence desorption processes, which in turn will affect the ion yield and the degree of in-source fragmentation of a molecule. In the beam-based method of secondary ion mass spectrometry (SIMS), in-source fragmentation can be significant and molecule specific due to the hard ionization method of using a primary ion beam for molecule desorption. To investigate the role of the substrate on orientation and in-source fragmentation, we have used atomistic simulations—molecular dynamics in combination with density functional theory calculations—to explore the desorption of a sphingolipid (palmitoylsphingomyelin) from a model surface (gold). We then compare SIMS data from this model system to our modeling findings. Using this approach, we found that the combined adsorption and binding energy of certain bonds associated with the headgroup fragments (C3H8N+, C5H12N+, C5H14NO+, and C5H15PNO4+) was a good predictor for fragment intensities (as indicated by relative ion yields). This is the first example where atomistic simulations have been applied in beam-based ionization of lipids, and it presents a new approach to study biointerfacial lipid ordering effects on SIMS imaging.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2024

Sub-pilot-scale Production of High-Value Products from U.S. Coals

Investigators from the University of Utah, University of Wyoming and Marshall University pursued a program to study the conversion of raw coal to high-value products of carbon fiber and silicon carbide. Team members also developed an initial framework for a data portal that can incorporate laboratory data on coal processing and product quality, and also work with tools for machine learning for data analysis, data visualization and economic assessment. Experimental R&D efforts focused on the conversion of raw coal to coal tar and other byproducts, and the resulting tar intermediates were upgraded to form anisotropic and isotropic pitch materials. These pitch materials were produced from coal using both thermal (pyrolysis) and chemical (mild solvolysis liquefaction) decomposition of raw coal. Four different coals were studied: Utah bituminous coal (Sufco), Wyoming PRB coal (Black Thunder), Illinois bituminous coal (Illinois #6), and West Virginia bituminous coal (Flying Eagle). Both metallurgical-grade coking coals and lower-grade steam coals were investigated, and controlled secondary gas-phase reactions were used during a two-stage pyrolysis process to induce cracking and condensation reactions among the pyrolytic tar species. This approach successfully improved the performance of the lower grade coals for yielding pitch materials, with properties more consistent with a commercial-grade pitch that had previously demonstrated success for quality carbon fiber production. The use of waste plastic materials was also studied, to help improve physical and chemical characteristics of the intermediate tars and final pitch product; in particular, for lowering the pitch softening point to an acceptable level for melt spinning carbon fiber. Mild solvolysis liquefaction was also used as a method for producing pitch for carbon fiber production. As expected, significantly higher pitch yields were obtained using this approach, and waste plastic materials were also successfully used to reduce pitch softening point to an acceptable level. The plastic materials were also utilized to create a solvent for the mild solvolysis process, and this plastic-derived solvent was shown to provide results consistent with more expensive commercial chemical solvents, and could thus avoid the need for costly recovery and recycle of a liquefaction solvent. Additional experimental R&D focused on the production of silicon carbide (β-SiC) from the residual char byproduct from pitch production, and also on the production of carbon fiber from the anisotropic pitch. SiC was successfully synthesized using a mixture of residual char and sandstone at a ratio of 1:1. Reaction temperature and residence time were optimized and yielded a product purity of 81%. For carbon fiber production, the most successful pitch samples were obtained from the mild solvolysis liquefaction approach, combined with the use of a plastic (HDPE)-derived solvent. Fiber properties improved over time as laboratory fiber production methodologies improved, and final yields of carbon fiber were obtained with a diameter of 12.14 ± 1.10 um, Modulus of 173.73 ± 15.25 GPa, and Tensile Strength of 1.04 ± 0.10 GPa. A proof-of-concept Modern Community Research Data Portal (MCRDP) was developed and deployed for coal and coal-derived pitch characterization, with the full support of (i) remote web-based access, (ii) distributed analysis, (iii) interactive visualization and exploration, (iv) shared and long-term data access, (v) advanced query capabilities and (vi) real-time collaboration. The Coal to Products Data Portal “coaltoproducts.org” provides researchers with space to store and share data within a project, tools for analyzing and understanding data for scientific investigation, and the ability to publish data to the broader community for reproducibility. The portal leverages the Material Commons 2.0 (MC) platform developed by the Center for PRedictive Integrated Structural Materials Science (PRISMS) of the University of Michigan, to achieve long-term longevity of data collections and, more importantly, collaborative science. A number of data visualization tools were also assessed and implemented for interrogating the experimental and modeling data. The machine learning portion of this project analyzed datasets from two different coal conversion processes performed on a diverse set of coal samples from both the coal pyrolysis experiments and the solvent liquefaction experiments. The work was initiated by exploring standard regression models on the pyrolysis data, aiming to understand the impact of sample characteristics and processing conditions on key product metrics. Over the course of the project, the focus expanded to include a variety of machine learning tools, delving into both supervised and unsupervised learning methods. Models tested on the pyrolysis data included linear, ridge, lasso, elastic-net, Gaussian process, random forest regression, and AutoSklearn, and the approach was continually refined to enhance predictive accuracy and model interpretability. Similar techniques were applied to the liquefaction data with an additional focus on feature engineering. Along with mesophase content, additional outputs of interest were the pitch yield, softening point, and QI content. Insights derived from these analyses are crucial in determining the factors influencing the quality and yield of coal-derived products. As the work progressed, the research evolved from foundational model comparisons to analyses of random forests, decision paths, and feature importance scores. A thorough market analysis was performed to examine the prospects of coal-based carbon fibers. The best opportunities for coal come from its lower and more stable price relative to petroleum, particularly for subbituminous coals, which is the primary advantage that a coal refinery may have over a petroleum refinery. Before a commercial CTP production facility can be modeled, however, several things need to be understood regarding the nature of the would-be coal refinery. These include the technology to be deployed, the size of facility, the volume(s) of co-product(s), and the waste and emissions profile of the plant. The volume of co-products and waste may be substantial and will require separate market analysis to ensure viability. In the near-term, the importance of coal tar pitch, in the form of carbon pitch, to the aluminum and steel industries is likely to overshadow the alternative use of this material as an input for carbon fiber. The importance of steel and aluminum in building materials, and the need for carbon materials in their manufacturing, will ensure that demand for these products remains for the long run. In addition, carbon fiber may also be the best substitute for steel and aluminum well into the future. While society will eventually be able to shift production of much of its electricity needs to renewables, it will not be able to shift away from fossil fuels for production of high-strength construction and vehicular materials. Demand for carbon fiber is expected to increase quickly, but the volume of carbon fiber and the amount of coal that would be needed to produce even a sizeable share of this market may still be relatively small compared to current coal production. Thus, other coal-based products like graphene, graphite, carbon foams, resins, and carbon-based building products will play important roles in sustaining coal production as coal-fired power generation continues to decline.

01 COAL, LIGNITE, AND PEAT↗
DOE OSTI2025

Broadband Fourier-Transform Optical Photothermal Infrared Spectroscopy and Imaging

Infrared (IR) spectroscopy is a powerful method for mapping chemical heterogeneity on the microscale. Synchrotron IR radiation uniquely provides a high brightness and broad bandwidth to further extend the capabilities of IR spectroscopic imaging. However, the diffraction-limited spatial resolution of IR spectroscopy is insufficient for studies requiring submicrometer spatial differentiation. Optical photothermal IR (O-PTIR) microscopy is a powerful, emerging method that overcomes the IR diffraction limit in IR hyperspectral imaging by employing a modulated IR beam and a visible probe laser beam to detect local temperature-induced modulation at the visible diffraction limit. In this work, we extend the spectral range of photothermal infrared measurements by incorporating a synchrotron IR source, demonstrating a combined synchrotron-based O-PTIR modality that enables high spatial resolution far-field chemical imaging spanning the entire mid-IR range. Both optical- and fluorescence-detected photothermal modalities were performed using a step-scan interferometer, demonstrating improved spectral range (541-4000 cm-1) when compared to optical photothermal microscopy with commercial laser sources (800-1800 cm-1 for this particular source) and improved spatial resolution, when compared to synchrotron microspectroscopy measurements. Following these initial validation studies, synchrotron Fourier-transform fluorescence-detected photothermal IR spectroscopy in combination with synchrotron microspectroscopy measurements was used to differentiate cells in mouse brain tissue sections, which requires submicron spatial resolutions beyond those accessible by IR spectroscopy alone.

Razumtcev, Aleksandr↗
DOE OSTI2025

Thermally Evaporated Naphthalene Diimides as Electron Transport Layers for Perovskite Solar Cells

Thermally evaporated organic electron transport layers (ETLs) have the potential to enable high-performance and scalable perovskite solar cells (PSCs). Among these, naphthalene diimide (NDI)-based ETLs are a promising family of materials that exhibit the optoelectronic properties, ambient stability and versatility required of high-performance ETLs. Here, we synthesized five NDI derivatives with varying functional groups and identified the two most promising candidates for evaluating the impact of molecular structure on processability via thermal evaporation. While phosphonic acid functionalization was shown to introduce thermal instability, leading to chemical changes during evaporation, NDI-bis N-phenyl-bromide (NDI-(PhBr) 2 ) emerged as a promising ETL candidate. NDI-(PhBr) 2 demonstrated excellent compatibility with the thermal evaporation process and enabled PSCs with power conversion efficiencies (PCEs) of 15.6%, surpassing all previously reported PSCs containing thermally evaporated NDI ETLs. Furthermore, NDI-(PhBr) 2 exhibited excellent operational stability, retaining 75% of the initial PCE after 150 h of operation under continuous illumination at 65 °C. These results highlight the potential of NDI-based ETLs for advancing the scalability and performance of PSCs.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Semi-Automated Creation of Density Functional Tight Binding Models through Leveraging Chebyshev Polynomial-Based Force Fields

Density functional tight binding (DFTB) is an attractive method for accelerated quantum simulations of condensed matter due to its enhanced computational efficiency over standard density functional theory (DFT) approaches. However, DFTB models can be challenging to determine for individual systems of interest, especially for metallic and interfacial systems where different bonding arrangements can lead to significant changes in electronic states. In this regard, we have created a rapid-screening approach for determining systematically improvable DFTB interaction potentials that can yield transferable models for a variety of conditions. Our method leverages a recent reactive molecular dynamics force field where many-body interactions are represented by linear combinations of Chebyshev polynomials. This allows for the efficient creation of multi-center representations with relative ease, requiring only a small investment in initial DFT calculations. Here, we have focused our workflow on TiH 2 as a model system and show that a relatively small training set based on unit-cell-sized calculations yields a model accurate for both bulk and surface properties. Our approach is easy to implement and can yield reliable DFTB models over a broad range of thermodynamic conditions, where physical and chemical properties can be difficult to interrogate directly and there is historically a significant reliance on theoretical approaches for interpretation and validation of experimental results.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗