Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “CASTINGS”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

From casting to 3D printing geopolymers: A proof of concept

The objective of this paper is to define a mix design strategy allowing the implementation of geopolymer in powder bed 3D printing. In a selective binder approach, an aluminosilicate powder bed is activated through the deposit of an alkaline silicate solution. We first show that, in comparison to casting, this technology requires mastering the spreading of the liquid into the powder bed to ensure that the reaction takes place where it is needed. A series of experiments at the drop level, mimicking the 3D printing process, were performed to determine the printing solution composition for a given powder bed packing. We then highlight the relationship between the compressive strength of the printed geopolymer and the powder bed saturation, controlled by the printing parameters. Finally, SEM/EDX analysis confirm the formation of geopolymer with desired Si/Al and Na/Al ratios in the resulting printed material.

36 MATERIALS SCIENCE↗

Sulfate performance of blended cements (limestone and illite calcined clay) exposed to aggressive environment after casting

This paper evaluates how early aggressive exposure affects the sulfate resistance of blended cements containing limestone filler and/or calcined clay. Mortar and cement paste specimens were elaborated with different combinations of limestone filler and two different illitic calcined clays and exposed to a sodium sulfate solution shortly after casting. Assessment of sulfate resistance was based on expansion, mass variation, and compressive strength. Microscale evolution and distribution were examined by mercury intrusion porosimetry, X-ray diffraction, and scanning electron microscopy with energy-dispersive spectrometry measurements. Results prove superior sulfate resistance of compositions with high calcined clay content over limestone filler addition. Furthermore, the results reported suggest that the pozzolanic reaction progresses enough to reduce the sulfate ingress even at early exposure conditions. Therefore, calcined clay replacement can still provide effective pore refinement to limit sulfate penetration, increase strength, and reduce available CH to limit expansive phase formation.

36 MATERIALS SCIENCE↗

Alkali-silica reaction expansion model for confined concrete with stress-dependency and casting direction anisotropy

Alkali-silica reaction (ASR) is a deleterious chemical reaction between alkali hydroxyl ions and types of silica found in some aggregates of concrete. Owners and regulators of nuclear power plants aim to ensure the safety of the concrete structures with optimal maintenance strategies. A new model was developed for predicting the expansion of concrete structures affected by alkali-silica reaction. The model includes a novel combination of existing models as an alkali-silica reaction advancement model, a casting direction anisotropic expansion model, a stress-dependent anisotropic expansion model, and a material property evolution model dependent on the degree of ASR expansion. The model parameters were calibrated based on existing literature data and data generated by previous efforts of this study. The calibrated model was then validated with the experiments carried out in previous efforts of this study. The model was shown to accurately predict the ASR-expansion of large-scale reinforced concrete specimens with confinement.

36 MATERIALS SCIENCE↗

Influence of casting porosity on the corrosion behaviour of Mg0.1Si

We investigated the influence of casting porosity on the corrosion behaviour of Mg0.1Si for immersion in 3.5% NaCl solution saturated with Mg(OH) 2 . The corrosion behaviour was characterised using (i) hydrogen evolution, (ii) weight loss, (iii) cathodic polarisation curves, (iv) electrochemical impedance spectroscopy (EIS), and (v) an examination of the corroded surfaces. Specimens with porosity had higher corrosion rates attributed to the corrosion associated with the pores activating significant corrosion over the whole specimen surface, wherein important aspects were (i) the breakdown of a partly protective surface film, and (ii) micro-galvanic acceleration of the corrosion by Fe-rich particles.

36 MATERIALS SCIENCE↗

3D microstructure reconstruction of casting aluminum alloy based on serial block-face scanning electron microscopy

In this work, the inner microstructure of aluminum-silicon casting alloy was experimentally investigated to reveal the spatial morphology and phase distribution. Its industrial use is as a light-weight structural material. As a powerful three-dimensional (3D) imaging tool at the nano-scale, the serial block-face scanning electron microscopy (SBFSEM) was employed to investigate the specimens. After being 3D reconstructed, the images were visualized to identify preference for several specific intermetallics by quantitative analysis. It was found that these phases have certain relationships in spatial distribution and differences in spatial shapes. In conclusion, the spatial distribution of cracks was studied to understand their propagation and growth.

3D microstructure reconstruction↗

Laser-induced slip casting as an additive manufacturing approach for silicon carbide

Here, this work presents processing silicon carbide (SiC) with the laser-induced slip casting (LIS) additive manufacturing (AM). SiC was stabilized in water with polyethyleneimine (PEI) dispersant, and SiC slurries were made with rheology for LIS printing. High-density ceramic parts were printed, followed by single-step binder burnout and sintering. The printed parts achieved 93–95 % of theoretical density. X-ray computed tomography (XCT) revealed a small distribution of flaws exceeding 100 microns. The mechanical properties were measured in both parallel and perpendicular to the printing layers, and the orientation with layers perpendicular to the bending moment resulted in higher strength compared to the parallel direction. Porosity resulting from processing and large inclusions of boron carbide (B4C) were the root cause of failure in the measured samples. Despite these defects through this effort, this new approach demonstrates promise for green forming of SiC with densities greater than 95 % theoretical and tensile strengths above 250 MPa.

Additive Manufacturing↗

Microstructure and mechanical properties of ultrasonic spot welding of AA7075-T6 and A380 casting aluminum alloy

Ultrasonic spot welding (USW) was employed to join AA7075-T6 and casting Al alloy A380. Under a constant welding power, the influence of the welding time duration (from 1 s to 3 s) on peak temperature, microstructure, hardness, and mechanical strength of the joints were studied. It was found that the peak temperature increased with welding time. A sound solid-state metallurgical bonding was obtained at the joint interface. The cracks occurred at the edge of the joints were eventually eliminated as the welding time increased. A layer of refined grains formed in A380 adjacent to the bonding line. Further, hardness reduction occurred in AA7075 at the joint interface and the degree of hardness reduction and the volume increased with the peak temperature. By increasing welding time, lap shear tensile tests show that the peak load increased from 5.3 kN to 6.55 kN. The corresponding interfacial shear strength ranged from 96.29 MPa to 99.72 MPa, lower than the shear strength of both base materials (331 MPa for AA7075 and 185 MPa for A380). All joint samples exhibited interfacial fracture after lap shear tensile testing, with a thin layer of A380 remnant attached to AA7075 at the center of the fractured surface.

36 MATERIALS SCIENCE↗

Microstructural characterization of as-cast U-20Pu-10Zr-3.86Pd and U-20Pu-10Zr-3.86Pd-4.3Ln

Palladium is being investigated as a potential additive to metallic fuel to bind fission product lanthanides, with the goal of reducing or preventing fuel-cladding chemical interactions (FCCI). A primary cause of FCCI is the lanthanide fission products moving to the fuel periphery and interacting with the cladding. This interaction will lead to wastage of the cladding and eventually to a cladding breach. The current study is a scanning electron microscopy (SEM) and transmission electron microscopy (TEM) investigation of as-cast U-20Pu-10Zr-3.86Pd and U-20Pu-10Zr-3.86Pd-4.3Ln in wt%, where Ln = 53Nd-25Ce-16Pr-6La. In U-20Pu-10Zr-3.86Pd, PdZr2 is forming, along with a possible ternary phase between Pu, Zr, and Pd. Pu is also present in the Pd-Ln precipitates formed in U-20Pu-10Zr-3.86Pd-4.3Ln. In the LnPd phase, Pu appears to be substitutional, forming (Ln,Pu)Pd. The other prominent phase, which appears to be Ln7Pd3, has a fine, lamellar structure. As a result, the lanthanides remain essentially constant across this fine structure, but Pu and Pd alternate as to which has the higher concentration.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Phase evolution of U-Zr system in a thermal cycling neutron diffraction experiment: as-cast U-35Zr and U-50Zr

Here, phase evolution of as-cast U-35 wt% Zr and U-50 wt% Zr alloys during thermal cycling (303–1073 K) was investigated using in-situ neutron diffraction. Analysis was performed using Rietveld crystal and microstructure refinements from time-of-flight neutron diffraction data, with a focus on evolution of lattice parameter, atom ordering, unit cell volume, and weight fractions during the thermal cycling. Disordered δ-UZr 2 and residual γ-(U,Zr) phase are retained in the field of δ of the U-Zr equilibrium phase diagram for the U-50Zr sample, and in the field between δ and α-U for the U-35Zr sample. The α phase that is present in the reported phase diagrams of U-Zr was not observed in the diffraction patterns. The evolutions of lattice parameter and unit cell volume of δ and γ are affected by both thermal expansion and chemistry.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Titanium porous-transport layers for PEM water electrolysis prepared by tape casting

While the porous-transport layer (PTL) is a key component in PEM electrolyzers, it is one of the most underexplored due to limited available structures. In this work, we present a novel PTL design for PEM water electrolyzers enabled by a cost-effective, scalable tape-casting technique. Here, a precise control of the PTL pore structure is achieved by incorporating poreformers of various sizes, and by varying the titanium and poreformer ratio. The structures are characterized with SEM and synchrotron X-ray computed tomography imaging techniques. Comprehensive electrochemical performance analysis demonstrates that higher titanium loading provides improved contact at the catalyst-layer/PTL interface but suffers from severe mass-transport losses due to gas bubbles. We solve this mass-transport problem by mixing in large poreformer beads that produce a highly porous structure with excellent gas removal properties yet still maintaining mechanical integrity. The PTL fabricated with 60:40 Ti:PMMA ratio and 60 μm PMMA bead size outperformed the standard commercial Ti powder-based PTL by 62 mV at 4 A/cm 2 .

25 ENERGY STORAGE↗

Effect of scandium on the microstructure and ageing behaviour of cast Al-6Mg alloy

Microstructural modification and grain refinement due to addition of scandium in Al-6Mg alloy has been studied. Transmission electron microscopy is used to understand the microstructure and precipitation behaviour in Al-6Mg alloy doped with scandium. It is seen from the microstructure that the dendrites of the cast Al-6Mg alloy have been refined significantly due to addition of scandium. Increasing amount of scandium leads to a greater dendrite refinement. The age hardening effect in scandium added Al-6Mg alloys has been studied by subjecting the alloys containing varying amount of scandium ranging from 0.2 wt.% to 0.6 wt.% to isochronal and isothermal ageing at various temperatures for different times. It is observed that significant hardening takes place in the aged alloys due to the precipitation of scandium aluminides.

36 MATERIALS SCIENCE↗

Effect of tungsten addition on the toughness and hardness of Fe{sub 2}B in wear-resistant Fe-B-C cast alloy

The effects of tungsten additions of 0%, 1.12%, 2.04%, and 3.17% (in wt.%) on the morphology, fracture toughness and micro-hardness of Fe{sub 2}B in Fe-B-C cast alloy were investigated. The results indicate that, with the increase of tungsten addition, the morphology and distribution of Fe{sub 2}B have no change and a new W-containing phase, except the (Fe, W){sub 2}B with a certain tungsten solution, does not form, and that the fracture toughness of Fe{sub 2}B increases first and then decreases, while the hardness increases first and then has a little change. Compared with the fracture toughness (3.8 MPa{center_dot}m{sup 1/2}) of Fe{sub 2}B without tungsten addition, the toughness at 2.04 wt.% tungsten can be improved by about above 80% and achieves about 6.9 MPa{center_dot}m{sup 1/2}, and variation characteristics of hardness and toughness of Fe{sub 2}B were also testified by viewing the indentation marks and cracks on the Fe{sub 2}B, respectively. - Highlights: Black-Right-Pointing-Pointer Poor toughness of Fe2B decreases obviously the wear resistance of the alloy. Black-Right-Pointing-Pointer As W content increases, Fe2B's toughness increases first and then decreases. Black-Right-Pointing-Pointer As W content increases, Fe2B's hardness first increases and then has little change. Black-Right-Pointing-Pointer The toughness at 2.04 % W can be improved by above 80% more than that at 0% W.

36 MATERIALS SCIENCE↗

Analysis of wear track and debris of stir cast LM13/Zr composite at elevated temperatures

Particulate reinforced aluminum metal matrix composite is in high demand in automobile industry where the operational conditions vary from low to high temperature. In order to understand the wear mode at elevated temperature, this study was planned. For this purpose we developed a metal matrix composite containing aluminum alloy (LM13) as matrix and zircon sand as particulate reinforcement by stir casting process. Different amounts of zircon sand (5, 10, 15 and 20 wt.%) were incorporated in the matrix to study the effect of reinforcement on the wear resistance. Dispersion of zircon sand particles in the matrix was confirmed by using optical microscopy. Sliding wear tests were done to study the durability of the composite with respect to the base alloy. The effects of load and temperature on wear behavior from room temperature to 300 Degree-Sign C were studied to understand the wear mechanism deeply. Surface morphology of the worn surfaces after the wear tests as well as wear debris was observed under scanning electron microscope. Mild to severe wear transition was noticed in tests at high temperature and high load. However, there is interesting change in wear behavior of the composite near the critical temperature of the composite. All the observed behavior has been explained with reference to the observed microstructure of the wear track and debris. - Highlights: Black-Right-Pointing-Pointer Good interfacial bonding between zircon sand particles and Al matrix was observed. Black-Right-Pointing-Pointer The effect of temperature on the wear behavior of LM13/Zr composites was studied. Black-Right-Pointing-Pointer Wear resistance of the composite was improved with addition of zircon sand. Black-Right-Pointing-Pointer Transition temperature from mild to severe wear also improved in composite. Black-Right-Pointing-Pointer SEM analysis of the tracks and debris was done to establish wear mechanism.

36 MATERIALS SCIENCE↗

Strengthening of σ phase in a Fe20Cr9Ni cast austenite stainless steel

The strengthening mechanism of σ phase in a Fe20Cr9Ni cast austenite stainless steel used for primary coolant pipes of nuclear power plants has been investigated. The yield and ultimate tensile strengths of aged specimens increased comparing with those of the unaged ones. It was found that the increase of strengths is due to the hard and brittle (σ + γ{sub 2}) structure which decomposed from α phase in the steel. Fracture surfaces of specimens after in situ tensile test showed that the inhibition of (σ + γ{sub 2}) structure on the dislocation movements was more significant than ferrite although cracks started predominately at σ/γ{sub 2} interfaces. The (σ + γ{sub 2}) structure behaves like a fiber reinforced composite material. - Highlights: • The strengthening mechanism of σ phase in a Fe20Cr9Ni CASS is investigated. • The yield and ultimate tensile strengths increase with increasing of σ phase. • The increase of strengths is due to hard and brittle (σ + γ{sub 2}) structure. • The (σ + γ{sub 2}) structure in CASS behaves like a fibre reinforced composite material. • The σ/γ{sub 2} and α/σ/γ{sub 2} boundaries hinder the movement of dislocation.

36 MATERIALS SCIENCE↗

Age hardening and creep resistance of cast Al–Cu alloy modified by praseodymium

The effects of praseodymium on age hardening behavior and creep resistance of cast Al–Cu alloy were investigated. The results indicated that praseodymium facilitated the formation of the θ′ precipitates during the age process and improved the hardness of the Al–Cu alloy. Besides, praseodymium resulted in the formation of the Al{sub 11}Pr{sub 3} phase in the grain boundaries and among the dendrites of the modified alloy. Because of the good thermal stability of Al{sub 11}Pr{sub 3} phase, it inhibits grain boundary migration and dislocation movement during the creep process, which contributes to the improvement in the creep resistance of the modified alloy at elevated temperatures. - Highlights: • Pr addition enhances the hardness and creep resistance of the Al–Cu alloy. • Pr addition facilitates the formation of the θ′ precipitates. • Pr addition results in the formation of the Al11Pr3 phase in the Al–Cu alloy.

36 MATERIALS SCIENCE↗

Elemental segregation and subsequent precipitation during solidification of continuous cast Nb–V–Ti high-strength low-alloy steels

In this study, elemental segregation during solidification and subsequent precipitation behaviour in a continuous cast Nb–V–Ti high-strength low-alloy steel was investigated by optical microscopy, scanning electron microscopy with energy dispersive X-ray spectroscopy and thermodynamic modelling. It is known that for steels with low carbon contents the pearlite that forms on slow cooling does so where the interdendritic liquid was present prior to final solidification. The alloying elements of Nb, Ti, Mn and V segregate into the interdendritic liquid during solidification, while Al preferentially segregates into the solidifying solid phase. The composition analysis on the slab samples verified the predicted element segregation behaviour, with a smaller difference in the concentrations of Mn and V in the pearlite and dendritic ferrite regions being observed compared to the Nb levels. Small (30–100 nm) spherical or irregular shaped Nb-rich precipitates (Nb(C, N) and (Nb, V)(C, N)) were mainly found in the pearlite regions, while angular Al-rich (60–300 nm) precipitates were found in the dendritic ferrite regions, in the form of AlN and complex AlN–V(C, N) precipitates. Small isolated ferrite regions surrounded by pearlite were observed in the microstructure and has two origins: one type is dendritic ferrite that appears as an isolated island due to a sectioning effect when observing the two-dimensional microstructure; the other is a ferrite idiomorph that forms in the interdendritic region due to the low carbon content of the steel. Accordingly, in these isolated ferrite islands two different precipitation behaviours are found; predominantly Al-rich particles in the dendritic regions or predominantly Nb-rich precipitates in the interdendritic ferrite idiomorphs. No Al-rich precipitates were observed in the interdendritic regions (pearlite or isolated ferrite idiomorphs) despite the Thermo-Calc predictions indicating a higher volume fraction of AlN in these regions compared to the dendritic regions. This is believed to be due to back diffusion of nitrogen after solidification reducing the available nitrogen, which reacts with the high Nb levels present. - Highlights: • Nb-rich precipitates (Nb(C, N) and (Nb, V)(C, N)) were mainly found in pearlite. • Angular Al-rich precipitates (AlN and AlN–V(C, N)) were found in dendritic ferrite. • Precipitation behaviour in isolated ferrite islands within pearlite was revealed. • Segregation of substitutional elements during solidification is retained. • Back diffusion of interstitial elements (C, N) occurred.

36 MATERIALS SCIENCE↗

Dynamic recrystallization behavior of an as-cast TiAl alloy during hot compression

High temperature compressive deformation behaviors of as-cast Ti–43Al–4Nb–1.4W–0.6B alloy were investigated at temperatures ranging from 1050 °C to 1200 °C, and strain rates from 0.001 s{sup −1} to 1 s{sup −1}. Electron back scattered diffraction technique, scanning electron microscopy and transmission electron microscopy were employed to investigate the microstructural evolutions and nucleation mechanisms of the dynamic recrystallization. The results indicated that the true stress–true strain curves show a dynamic flow softening behavior. The dependence of the peak stress on the deformation temperature and the strain rate can well be expressed by a hyperbolic-sine type equation. The activation energy decreases with increasing the strain. The size of the dynamically recrystallized β grains decreases with increasing the value of the Zener–Hollomon parameter (Z). When the flow stress reaches a steady state, the size of β grains almost remains constant with increasing the deformation strain. The continuous dynamic recrystallization plays a dominant role in the deformation. In order to characterize the evolution of dynamic recrystallization volume fraction, the dynamic recrystallization kinetics was studied by Avrami-type equation. Besides, the role of β phase and the softening mechanism during the hot deformation was also discussed in details. - Highlights: • The size of DRXed β grains decreases with increasing the value of the Z. • The CDRX plays a dominant role in the deformation. • The broken TiB{sub 2} particles can promote the nucleation of DRX.

36 MATERIALS SCIENCE↗

Damage morphology study of high cycle fatigued as-cast Mg–3.0Nd–0.2Zn–Zr (wt.%) alloy

Laser scanning confocal microscopy (LSCM) and Electron back-scattered diffraction (EBSD) were applied to the study of surface morphology variation of as-cast Mg–3.0Nd–0.2Zn–Zr (NZ30K) (wt.%) alloy under tension-compression fatigue test at room temperature. Two kinds of typical damage morphologies were observed in fatigued NZ30K alloy: One was parallel lines on basal planes led by the cumulation of basal slips, called persistent slip markings (PSMs), and the other was lens shaped, thicker and in less density, led by the formation of twinning. The surface fatigue damage morphology evolution was analyzed in a statistical way. The influences of stress amplitude and grain orientation on fatigue deformation mechanisms were discussed and the non-uniform deformation among grains and the PSMs, within twinning were described quantitatively. - Highlights: • Fatigue morphology evolution was studied by Laser Scanning Confocal Microscopy. • 3D morphology of persistent slip markings and twins was characterized. • Non-uniform deformation among grains, the PSMs and twins were quantified. • Initiations of fatigue crack were clearly investigated.

36 MATERIALS SCIENCE↗