Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “BLAST”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2023

Reduction of Iron‐Ore Pellets Using Different Gas Mixtures and Temperatures

Direct reduction of iron ore (DRI) is gaining an increased attention due to the growing need to decarbonize industrial processes. The current industrial DRI processes are performed using reformed natural gas, which results in CO 2 emission, although it is less than carbothermic reduction in the blast furnace. Carbon‐free reduction may be realized through the utilization of green H 2 as a reducing agent, in place of natural gas. Herein, the effects of various gas mixtures and temperature on the reduction kinetics of the hematite iron‐ore pellets are focused on in this work. Pellets are reduced at 700, 800, 850, and 900 °C in hydrogen and using various gas mixes at 850 °C. Morphology of the pellets is investigated with the help of scanning electron microscopy and mercury intrusion porosimetry. The effects of temperature and gas composition on the reduction kinetics and porosity of the pellets are discussed. A notable effect of reduction rate on the internal structure of the pellets is detected, slower reduction rate yielded bigger pores offsetting the gas composition. Higher temperature results in coarser pores and higher porosity. Finally, increase of CO content in the gas mix also leads to bigger pore size.

36 MATERIALS SCIENCE↗
DOE OSTI2020

Assessment of Dynamic Fracture in Ultra-High Performance Concrete Using Synchrotron X-ray Source

Ultra-high-performance concretes (UHPCs) retain higher ultimate (compressive) strengths and greater durability relative to traditional concrete materials. As a result, they are enabling construction materials for blast resistant structures, where a higher capacity for energy absorption is required. In past investigations, the strength of UHPCs was shown to retain a dependency on strain rate. Still, the failure mechanisms which govern this rate dependency have yet to be completely elucidated. In the current study, the dynamic fracture behavior of Cor-tuf UHPC was assessed, in-situ, using a Synchrotron X-ray source in phase contrast imaging (PCI) mode. Prior to testing, the material’s morphology was characterized using X-ray computed tomography (CT) and scanning electron microscopy (SEM). A polychromatic pulsed X-ray source, high-speed camera and Kolsky bar apparatus were used in tandem, to observe the transient failure modes. A pin was placed at the end of the incident bar to control the location of damage initiation, and tests were performed at a constant velocity of ~6 m/s. These test conditions were observed to yield cracks with median and/or cone like geometries. Despite the variation in the crack paths, a significant difference in peak load was not observed. The failure mode was also observed to depend on the microstructure of the concrete samples.

Kolsky bar↗
DOE OSTI2024

A Dataset of CFD Simulated Industrial Furnace Images for Conditional Automatic Generation with GANs

The steel industry is constantly looking for ways to automate processes and improve efficiency. A standard practice in industry is to simulate how complex systems will operate before they are actually used. Some complex systems, including steel industry processes such as blast furnaces, require complex physics-based simulations utilizing computational fluid dynamics (CFD). These CFD physics-based simulations are very accurate but can take significant time and computational resources to process, resulting in challenges for the implementation of the models in real-world operational environments. In recent years, deep learning (DL) has been considered as a substitute for these CFD models. DL models can be trained on validated CFD simulation data and then used for industrial process inference. Previous DL-based solutions have made great contributions for industrial automation but are currently missing the additional visualization component that CFD simulations also provide. In this paper, we propose a dataset for simple DL generative approaches that can help to address this issue. The dataset and methodology under development to approach this prediction are discussed in this work.

Calix, Ricardo↗
DOE OSTI2020

Constraining the Chiral Magnetic Effect with charge-dependent azimuthal correlations in Pb-Pb collisions at $ \sqrt{s_{\mathrm{NN}}} $ = 2.76 and 5.02 TeV

Systematic studies of charge-dependent two- and three-particle correlations in Pb-Pb collisions at $ \sqrt{s_{\mathrm{NN}}} $ = 2.76 and 5.02 TeV used to probe the Chiral Magnetic Effect (CME) are presented. These measurements are performed for charged particles in the pseudorapidity ( η ) and transverse momentum ( p T ) ranges | η | < 0 . 8 and 0 . 2 < p T < 5 GeV/ c . A significant charge-dependent signal that becomes more pronounced for peripheral collisions is reported for the CME-sensitive correlators γ 1, 1 =$\langle4cos( φ α + φ β - 2Ψ 2 )$\rangle$ and γ 1, - 3 = $\langle$cos( φ α - 3 φ β + 2Ψ 2 )$\rangle$. The results are used to estimate the contribution of background effects, associated with local charge conservation coupled to anisotropic flow modulations, to measurements of the CME. A blast-wave parametrisation that incorporates local charge conservation tuned to reproduce the centrality dependent background effects is not able to fully describe the measured γ 1 , 1 . Finally, the charge and centrality dependence of mixed-harmonics three-particle correlations, of the form γ 1, 2 = $\langle$cos( φ α + 2 φ β - 3Ψ 3 )$\rangle$, which are insensitive to the CME signal, verify again that background contributions dominate the measurement of γ 1 , 1 .

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2023

Probing the chiral magnetic wave with charge-dependent flow measurements in Pb-Pb collisions at the LHC

The Chiral Magnetic Wave (CMW) phenomenon is essential to provide insights into the strong interaction in QCD, the properties of the quark-gluon plasma, and the topological characteristics of the early universe, offering a deeper understanding of fundamental physics in high-energy collisions. Measurements of the charge-dependent anisotropic flow coefficients are studied in Pb-Pb collisions at center-of-mass energy per nucleon-nucleon collision $\sqrt{s_{\textrm{NN}}}$ = 5.02 TeV to probe the CMW. In particular, the slope of the normalized difference in elliptic (v 2 ) and triangular (v 3 ) flow coefficients of positively and negatively charged particles as a function of their event-wise normalized number difference, is reported for inclusive and identified particles. The slope ${r}_3^{\textrm{Norm}}$ is found to be larger than zero and to have a magnitude similar to ${r}_2^{\textrm{Norm}}$, thus pointing to a large background contribution for these measurements. Furthermore, ${r}_2^{\textrm{Norm}}$ can be described by a blast wave model calculation that incorporates local charge conservation. In addition, using the event shape engineering technique yields a fraction of CMW (f CMW ) contribution to this measurement which is compatible with zero. This measurement provides the very first upper limit for f CMW , and in the 10–60% centrality interval it is found to be 26% (38%) at 95% (99.7%) confidence level.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2018

Explosion-induced ignition and combustion of acetylene clouds

We investigate the explosion-induced ignition and combustion of an acetylene cloud in a rectangular chamber (10 cm × 10 cm × 39 cm). In the experiments, a 0.2-g PETN charge was located at $x = 9.7\,\hbox {cm}$ and a soap bubble (d=5cm) filled with pure acetylene was located at $x = 27\,\hbox {cm}$ as measured relative to the end wall. Detonation of the charge created a blast wave that crushed the soap bubble—inducing mixing with the air. After 0.55 ms, the mixture ignited, forming at turbulent combustion cloud. The flow was modeled using the compressible Navier–Stokes equations assuming unity Lewis number. Arrhenius-based kinetics were used to model ignition. Adaptive mesh refinement was used to capture turbulent mixing on the grid (the MILES approach of J. Boris). Computed pressures were found to be in agreement with measured pressure histories. Finite-rate kinetics were required to capture the ignition processes over the duration of the experiment.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2018

Preparation and Property Research of Perfluoropolyether Oil-Based Ferrofluid

In this study, perfluoropolyether oil-based ferrofluid was prepared to satisfy special demands in applications which are too harsh to conventional ferrofluids. Fe{sub 3}O{sub 4} magnetic nanoparticles were synthesized by co-precipitation and modified by perfluoropolyether carboxylic acid surfactant in the atmosphere without protective gas. Perfluoropolyether oil-based ferrofluid was prepared with modified nanoparticles and perfluoropolyether by high-energy ball milling. Properties of ferrofluid fabricated were verified through a series of experiments. Ferrofluid stability was tested by interval point-density method; the average density change is merely 0.0077 g/ml, and change rate is 0.37% after 500 days. Saturation magnetization is 582.46 Gs, much larger than the other four ferrofluids. The average volatility rate is 7.4985*10{sup − 5} g/h/cm{sup 2} at 80 °C after 260 h. Viscosity increases to 1825.7 mPa⋅ s under − 20 °C and still have mobility at − 40 °C. The ferrofluid can resist air blast for 8 h under 200 °C without oxidation or decomposition. Perfluoropolyether oil-based ferrofluid cannot be damaged by water or organic solvents. In addition, the ferrofluid can survive in pH = 1 acid or pH = 14 alkali at least 279 days without corrosion.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2018

Crucial Physical Dependencies of the Core-Collapse Supernova Mechanism

Here, we explore with self-consistent 2D Fornax simulations the dependence of the outcome of collapse on many-body corrections to neutrino-nucleon cross sections, the nucleon-nucleon bremsstrahlung rate, electron capture on heavy nuclei, pre-collapse seed perturbations, and inelastic neutrino-electron and neutrino-nucleon scattering. Importantly, proximity to criticality amplifies the role of even small changes in the neutrino-matter couplings, and such changes can together add to produce outsized effects. When close to the critical condition the cumulative result of a few small effects (including seeds) that individually have only modest consequence can convert an anemic into a robust explosion, or even a dud into a blast. Such sensitivity is not seen in one dimension and may explain the apparent heterogeneity in the outcomes of detailed simulations performed internationally. A natural conclusion is that the different groups collectively are closer to a realistic understanding of the mechanism of core-collapse supernovae than might have seemed apparent.

79 ASTRONOMY AND ASTROPHYSICS↗
DOE OSTI2025

Mercury sequestration in alkaline salt low-level radioactive waste

Liquid low-level radioactive waste at the Savannah River Site contains several species of mercury, including inorganic, elemental and methylmercury. This waste is solidified and stabilized in a cementitious waste form referred to as saltstone. Soluble mercury is stabilized as β-cinnabar, HgS as the result of reaction between the mercury and sulfur present in blast furnace slag, one of the cementitious regents. In this investigation, Mersorb®, a commercial granular activated carbon impregnated with sulfur, was evaluated as a pretreatment to remove mercury from the solution prior to cementation. Mersorb® was found to remove more than 96 mass percent of the methylmercury in simulated tank waste solution when the mass ratio of Mersorb® to mercury was above 2.5. Slag sequestered relatively more inorganic mercury than organic mercury in simulated tank waste after 24 hours of contact. This is likely due to the mercury-carbon bond being more covalent than the mercury-oxygen bond and therefore more difficult to break and slower to form HgS.

Cementitious Material↗
DOE OSTI2022

In-Situ Observation of FCC→HCP Transformation-Induced Plasticity Behavior During Dynamic Deformation of CoCrNi Multi-principal Element Alloys

CoCrNi multi-principal element alloys (MPEAs) have potential as high toughness, blast resistant materials, but limited studies of their high strain rate behavior have been performed. Their high toughness has been attributed to low stacking fault energies and the activation of toughness enhancing deformation mechanisms, such as twinning- and transformation-induced plasticity (TWIP and TRIP, respectively), that may be affected by increased strain rate. This work examines a series of CoCrNi MPEAs tested with a miniaturized pressure bar, while simultaneous synchrotron x-ray diffraction and imaging are performed, and compares these results to those collected during quasi-static deformation at elevated temperatures. Here, the collected diffraction indicates that TRIP was active at elevated strain rates for the most Co-rich alloys containing 50 or 55 at. pct. Co, while TRIP behavior was suppressed at elevated strain rates in a 40 at. pct. Co alloy anticipated to experience TRIP. The suppression of TRIP in the lower Co alloy at high strain rates is attributed to adiabatic heating, consistent with suppression of TRIP as a result of elevated temperatures.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Mechanism of Low-Temperature Reduction Degradation of Alumina-Containing Hematite Solid Solution Below 550 °C

Low-temperature reduction degradation (LTRD) of sinter has an adverse effect on blast furnace permeability, and it is mainly caused by the stress produced in the reduction process of hematite. This stress is strongly influenced by alumina dissolved in hematite crystal lattice. In this work, the experiments were conducted to investigate the effect of alumina dissolved in hematite solid solution (H{sub ss}) on LTRD by reducing H{sub ss} below 550 °C. Thermogravimetric analysis (TGA), X-ray diffraction (XRD), and optical microscope have been used to characterize the mass change and mineral change of samples, respectively. Jade software has been used to calculate the micro strain in magnetite for quantitatively studying the change of strain in reducing process. The results show that alumina was unfavorable to the reduction of H{sub ss} on thermodynamics, and the starting reduction temperature of H{sub ss} containing 6.0 mol pct alumina was 28 °C higher than that of pure hematite. According to the calculation on kinetics, the generation rate of stress was accelerated by dissolving alumina into hematite crystal lattice. The apparent activation energy of reduction reaction lowered from 47.89 to 28.07 kJ/mol with the increase of alumina content from 0.0 to 6.0 mol pct. The addition of alumina also increased the stress in the reduction products, and this stress was released in the form of LTRD.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2017

Corrosion and Fatigue Behavior of High-Strength Steel Treated with a Zn-Alloy Thermo-diffusion Coating

High and low cycle fatigue tests were conducted on high-strength steel using four-point bending. The materials tested were ASTM A723 steel in the as-machined condition, grit-blasted condition, MIL-DTL-16232 heavy manganese phosphate-coated condition, and ASTM A1059 Zn-alloy thermo-diffusion coated (Zn-TDC). The ASTM A723 steel base material exhibits a yield strength of ~1000 MPa. The effects of the surface treatments versus uncoated steel were examined. The fatigue life of the Zn-TDC specimens was generally reduced on as-coated specimens versus uncoated or phosphate-coated specimens. Several mechanisms are examined including the role of compressive residual stress relief with the Zn-TDC process as well as fatigue crack initiation from the hardened Zn-Fe alloy surface layer produced in the gas-metal reaction. Additionally, the effects of corrosion pitting on the fatigue life of coated specimens are explored as the Zn-TDC specimens exhibit significantly improved corrosion resistance over phosphate-coated and oiled specimens.

36 MATERIALS SCIENCE↗
DOE OSTI2019

Can synthetic lethality approach be used with DNA repair genes for primary and secondary MDS?

Cancer-specific defects in DNA repair pathways create the opportunity to employ synthetic lethality approach. Recently, GEMA (gene expression and mutation analysis) approach detected insufficient expression of BRCA or NHEJ (non-homologous end joining) to predict PARP inhibitors response. We evaluated a possible role of DNA repair pathways using gene expression of single-strand break (XPA, XPC, XPG/ERCC5, CSA/ERCC8, and CSB/ERCC6) and double-strand break (ATM, BRCA1, BRCA2, RAD51, XRCC5, XRCC6, LIG4) in 92 patients with myelodysplastic syndrome (73 de novo, 9 therapy-related (t-MDS). Therapy-related MDS (t-MDS) demonstrated a significant downregulation of axis BRCA1-BRCA2-RAD51 comparing to normal controls (p = 0.048, p = 0.001, p = 0.001). XRCC6 showed significantly low expression in de novo MDS comparing to controls (p = 0.039) and for patients who presented chromosomal abnormalities (p = 0.047). Downregulation of LIG4 was consistently associated with poor prognostic markers in de novo MDS (hemoglobin < 8 g/dL (p = 0.040), neutrophils < 800/mm{sup 3} (p < 0.001), patients with excess of blasts (p = 0.001), very high (p = 0.002)/high IPSS-R (p = 0.043) and AML transformation (p < 0.001). We also performed an evaluation of GEPIA Database in 30 cancer types and detected a typical pattern of downregulation as here presented in primary or secondary MDS. All these results suggest synthetic lethality approach can be tested with DNA repair genes (beyond that of BRCA1/2 status) for de novo and therapy-related myelodysplastic syndrome and may encourage clinical trials evaluating the use of PARP1 inhibitors in MDS. Graphic Abstract: .

62 RADIOLOGY AND NUCLEAR MEDICINE↗
DOE OSTI2019

Genome-Wide Analysis of Nitrate Transporter (NRT/NPF) Family in Sugarcane Saccharum spontaneum L.

Nitrate is the predominant nitrogen source for plant growth and development. However, sugarcane, globally used as the primary sugar crop and biofuel feedstock, displays a low nitrate use efficiency due to a low capacity in storing nitrate in shoots. It is well studied that the nitrate transporter (NRT/NPF) family functions as the gatekeeper in governing nitrogen uptake and distribution, and optimizing nitrogen utilization in plants. This makes it a promising target for improving nitrogen use efficiency in sugarcane. Here, we carried out a comprehensive analysis of NRT/NPF genes at a genome-wide scale in Saccharum spontaneum. A BLAST search of NRT/NPF genes was initially performed against recently released sugarcane genome, followed by phylogenetic, gene structure and protein motif analysis. Additionally, NRT/NPF gene expression profile from various tissues was obtained from RNA-seq data analysis. As a result, we identified 178 NPF, 20 NRT2, and 6 NRT3 genes which spread across all 8 monoploid chromosomes. NPF and NRT3 exhibit high levels of genetic diversities as opposed to NRT2 which is more evolutionarily conserved. Interestingly, several SsNPF genes are products of gene fusions of several tandem duplications, which provide valuable structural resources for functional characterization of nitrate transporters. Moreover, several genes are tissue-specific expressed, indicating roles in tissue-specific nitrate translocations. A substantial number of NRT/NPF genes are heterogeneous in terms of their gene structures and mRNA abundance. Taken together, our work provides a genetic foundation for future investigations of molecular and physiological functions of sugarcane nitrate transporters.

59 BASIC BIOLOGICAL SCIENCES↗
DOE OSTI2019

Preface: meshfree and particle methods for modeling extreme loadings

In memorium: This special issue is dedicated to Steve Attaway, who passed away on February 28, 2019. Steve Attaway worked at Sandia National Laboratories in Albuquerque, NM, for over 30 years making significant contributions in highperformance computing, shock physics, meshfree methods, the geosciences, concrete mechanics, and blast effects on structures.

99 GENERAL AND MISCELLANEOUS↗
DOE OSTI2020

HOSS: an implementation of the combined finite-discrete element method

Nearly thirty years since its inception, the combined finite-discrete element method (FDEM) has made remarkable strides in becoming a mainstream analysis tool within the field of Computational Mechanics. FDEM was developed to effectively “bridge the gap” between two disparate Computational Mechanics approaches known as the finite and discrete element meth-ods. At Los Alamos National Laboratory (LANL) researchers developed the Hybrid Optimization Software Suite (HOSS) as a hybrid multi-physics platform, based on FDEM, for the simulation of solid material behavior complemented with the latest technological enhancements for full fluid–solid interaction. Furthermore, in HOSS, several newly developed FDEM algorithms have been implemented that yield more accurate material deformation formulations, inter-particle interaction solvers, and fracture and fragmentation solutions. Additionally, an explicit computational fluid dynamics solver and a novel fluid–solid interaction algorithms have been fully integrated (as opposed to coupled) into the HOSS’ solid mechanical solver, allowing for the study of an even wider range of problems. Advancements such as this are leading HOSS to become a tool of choice for multi-physics problems. Finally, HOSS has been successfully applied by a myriad of researchers for analysis in rock mechanics, oil and gas industries, engineering application (structural, mechanical and biomedical engineering), mining, blast loading, high velocity impact, as well as seismic and acoustic analysis. This paper intends to summarize the latest development and application efforts for HOSS.

58 GEOSCIENCES↗
DOE OSTI2018

The Effect of Loading Frequency on Fatigue Life of Green onyx under Fully Reversed Loading

Rock structures, in reality, may be subjected to reversed tension-compression loading conditions due to blasting, earthquake, and traffic or injection-recovery process. In this case, loading frequency may have a great influence on fatigue life and behavior of rocks. The effect of loading frequency on fatigue life of a crystalline rock sample under fully reversed loading condition was examined. A new apparatus, based on the R. R. Moore fatigue test machine, was used to assess the fully reversed loading condition. The experimental tests were conducted with five sets of loading frequency and five levels of stress based on the ultimate tensile strength of samples. The test results showed that the variation of ultimate fatigue stress versus loading cycle number (S-N curve) of crystalline rock samples were in accordance with the observed results in other materials such as metals and ceramics. The results showed that fatigue life of a component is positively correlated with the frequency level. The fatigue life improves with increasing the loading frequency, but the improvement was more tangible at lower stress levels than at higher stress levels. The effect of loading frequency in an ordinary S-N equation was also formulated. The results also showed that the loading frequency does not influence the fatigue limit.

36 MATERIALS SCIENCE↗
DOE OSTI2018

Inferring Strength of Tantalum from Hydrodynamic Instability Recovery Experiments

Hydrodynamic instability experiments allow access to material properties at extreme conditions, where strain rates exceed 105 s -1 and pressures reach 100 GPa. Current hydrodynamic instability experimental methods require in-flight radiography to image the instability growth at high pressure and high strain rate, limiting the facilities where these experiments can be performed. An alternate approach, recovering the sample after loading, allows measurement of the instability growth with profilometry. Tantalum samples were manufactured with different 2D and 3D initial perturbation patterns and dynamically compressed by a blast wave generated by laser ablation. The samples were recovered from peak pressures between 30 and 120 GPa and strain rates on the order of 107 s -1 , providing a record of the growth of the perturbations due to hydrodynamic instability. These records are useful validation points for hydrocode simulations using models of material strength at high strain rate. Recovered tantalum samples were analyzed, providing an estimate of the strength of the material at high pressure and strain rate.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗