Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Advanced Nuclear Reactor”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44
All sourcesNASA NTRSDOE OSTI
DOE OSTI2024

The importance of delayed neutron precursors in gamma dose calculations for activated primary heat exchanger components in the Molten Salt Breeder Reactor

The Molten Salt Reactor (MSR) Multiphysics Applications technical area in the Nuclear Energy Advanced Modeling and Simulation program has supported the development of 3D Monte Carlo models of the Molten Salt Breeder Reactor (MSBR) over the last couple of years. This MSBR model was previously run with the Shift Monte Carlo code to perform radiation shielding calculations in the reactor cell area. The MSBR is a 2250 MWth (1000 MWe) liquid-fueled molten salt reactor design developed at Oak Ridge National Laboratory in the 1970s. Determining the source terms from activated primary heat exchanger (HX) components is important because delayed and prompt neutron fluxes incident on these components affect the dose rate in the primary HX maintenance areas. This information can be used in the development of remote handling procedures required during shutdown for maintenance. A methodology has been developed and is proposed in this paper to quantify the activated source term from the primary HX components as a result of the movement of the delayed neutron precursors in flowing primary fuel salt through the primary HXs in the MSBR. The goal of this research is to evaluate the gamma dose rates in the maintenance hatches above the primary HX using the activated HX source terms. The study showed that the gamma dose rates are approximately two orders of magnitudes higher when accounting for the neutron activation from the movement of delayed neutron precursors through the HXs than when flowing fuel is not considered. Thus, the movement of delayed neutron precursors must be taken into account for accurately predicting the neutron activation of primary loop components.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Fluoride-Cooled High-Temperature Pebble-Bed Reactor Reference Plant Model Updates

This work presents the latest improvements to, and investigations performed with, the Fluoride-Cooled High-Temperature Pebble-Bed Reactor reference plant models for the United States Nuclear Regulatory Commission. These models, developed with the Comprehensive Reactor Analysis Bundle, or BlueCRAB, serve as the foundation for the future development of detailed design evaluation models based on license applications. BlueCRAB is the code suite proposed for non-light-water reactor systems safety analyses, and it incorporates various simulation tools developed by the Nuclear Energy Advance Modeling and Simulation program, including the Griffin code for reactor physics, the Pronghorn and SAM codes for core thermal fluids, the BISON code for solid conduction and fuel performance, and the SAM code for system analysis. The primary objective of this work is to assess the level of readiness of BlueCRAB for modeling fluoride-cooled high-temperature pebble-bed reactors. We first developed numerical models in BlueCRAB that include the key physics for this technology, ensuring an adequate level of fidelity for modeling the core performance during accident scenarios. This was followed by simulation of transient scenarios, two loss-of-forced-cooling events (one protected and one unprotected), and two control rod withdrawal events (one delayed and one prompt supercritical reactivity insertion). The analysis includes comparisons between the 2-D thermal fluid porous media models in Pronghorn and SAM, comparisons between coupled Pronghorn-Griffin and coupled SAM-Griffin models for two loss-of-forced cooling events and one control rod withdrawal event, and comparisons between SAM single-solve and domain-overlapping approaches for multi-scale thermal fluid coupling. In addition, we performed comparisons between 3-D, 2-D, and 0-D neutronic models for the two control rod withdrawal scenarios with Pronghorn-Griffin. The results show that the BlueCRAB models led to physically intuitive solutions for the scenarios examined. The changes in the various scalar and vector fields such as the neutron flux, power, temperatures, densities, pressures, and velocities are all within the expected ranges, and their distributions can be explained from the system response of the transients and the geometric and material variations. Several comparisons suggest that the porous media models in Pronghorn and SAM can lead to similar solutions, even though they are based on different methodologies. The simulations demonstrate that there are differences between the various levels of fidelity, and it is advisable to have flexible tools that can cover the breadth and depth of needs that may arise in future technical evaluations. We believe that BlueCRAB’s capabilities represent a significant asset for confirmatory analyses aimed at resolving important safety questions.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

GDOE Bearing

Explore the source record for details and available documents.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2022

Coupling coarse-mesh CFD with fine-mesh CFD for modeling molten-salt reactors in the Virtual Test Bed (VTB)

The Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims at developing a simulation tool kit to accelerate the development and deployment of nuclear power technologies. NEAMS multiphysics tools have been designed to provide numerical simulation support for the design and licensing of GEN IV reactors. Pronghorn is NEAMS's coarse-mesh computational fluid dynamics (CFD) tool, which is designed to run 3D core transients in GEN IV reactors at a reduced computational cost. To increase their accuracy, coarse-mesh CFD simulations require calibrated closure coefficients. One way of computing these coefficients is via the Nek5000, NEAMS's high-fidelity CFD tool. This article discusses our current research lines in informing Pronghorn closure coefficients via Nek5000 to enable multiphysics simulations of the core cavity of the molten-salt fast reactor. We present an application in which Pronghorn mixing length turbulent viscosity has been calibrated from Nek5000 simulations. The resulting Pronghorn thermal-hydraulics model is then coupled to Griffin, the NEAMS neutron transport solver, to solve for the steady-state configuration of the molten-salt fast reactor. (authors)

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2022

Coupling coarse mesh CFD with fine mesh CFD for modeling for Molten Salt Reactors in the Virtual Test Bed VTB

The Nuclear Energy Advanced Modeling and Simulation (NEAMS) program aims at developing a simulation tool kit to accelerate the development and deployment of nuclear power technologies. NEAMS multiphysics tools have been designed to provide numerical simulation support for the design and licensing of GEN IV reactors. Pronghorn is NEAMS’s coarse-mesh computational fluid dynamics (CFD) tool, which is designed to run 3D core transients in GEN IV reactors at a reduced computational cost. To increase their accuracy, coarse-mesh CFD simulations require calibrated closure coefficients. One way of computing these coefficients is via the Nek5000, NEAMS’s high-fidelity CFD tool. This article discusses our current research lines in informing Pronghorn closure coefficients via Nek5000 to enable multiphysics simulations of the core cavity of the molten-salt fast reactor. We present an application in which Pronghorn mixing length turbulent viscosity has been calibrated from Nek5000 simulations. The resulting Pronghorn thermal-hydraulics model is then coupled to Griffin, the NEAMS neutron transport solver, to solve for the steady-state configuration of the molten-salt fast reactor.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2020

3D CFD Model Validation Using Benchmark Data of 1/16th Scaled VHTR Upper Plenum and Development of Wall Heat-Transfer Correlation For Laminar Flow

With support from the U.S. Department of Energy-Office of Nuclear Energy’s (DOE-NE’s) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, an effort has been pursued to support high-temperature gas-cooled reactor (HTGR) technology development and its modeling and simulation needs. There is a particular need for advanced modeling and simulation tools to predict thermal-fluid behavior in the nuclear reactor primary system, especially in the core and the lower and upper plena, during safety-related transients. In this report, two main such activities are presented relevant to the HTGRs: (1) three-dimensional (3D) computational fluid dynamics (CFD) validation using benchmark data from the upper plenum of Texas A&M University’s 1/16th scaled very-high-temperature gas-cooled reactor (VHTR), and (2) development of wall heat-transfer correlation for laminar flow in a wall-heated pipe. The CFD tool validation exercises can be helpful to choose the models and CFD tools to simulate and design specific components of the HTRGs such as upper plenum where jet mixing is a complex phenomenon. In a loss of forced circulation event, the laminar flow can be observed during the development of natural circulation flow. This work includes the development and validation of heat transfer correlations for laminar flow using the Nek5000 CFD code due to limited available experimental data for laminar flow conditions to guide low-order models (1D). In this report, the flow characteristics of a single isothermal jet discharging into the upper plenum was investigated using the Nek5000 Large-Eddy Simulation (LES) CFD tool. Several numerical simulations were performed for various jet-discharged Reynolds numbers ranging from 3,413 to 12,819. A grid-independent study was performed. The numerical results of mean velocity, root-mean-square fluctuating velocity, and Reynolds stress were compared against the benchmark data. Good agreement was obtained between simulated and measured data for axial mean velocities, except near the upper plenum hemisphere. The maximum predicted errors for axial mean velocities at various normalized coolant channel diameter heights of 1, 5, and 10 are 1.56%, 1.88%, and 3.82%, respectively. In addition, the predicted root-mean-square fluctuating velocity and Reynolds stress are qualitatively in agreement with the experimental data. The Nek5000 code was used to develop wall-heat transfer correlation for laminar flow in a cylindrical tube. Several simulations were performed for various Reynolds flow and wall-heat fluxes. A new heat transfer correlation was developed using data from Nek5000 simulation results and regression functions in Matlab. The developed heat transfer correlation is valid for various Reynolds flows from 200 to 2000. The predicted R² value for model fit was 0.875, which ensures that 87.5% of the model data lies on the Nek5000 data. Moreover, a machine learning (ML) tool was used to train and test the Nek5000 data. A good fit of the ML-based model was observed with the test data.

21 SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLANTS↗
DOE OSTI2024

Generating An Advanced Cross-section Library For HTGR Pebble Bed Depletion Calculations Using Reduced-Order Model Generation Techniques

For code development, Advanced Reactor Technologies - Gas Cooled Reactors Program (ART-GCR) rely on a collaboration with the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program, but the cross sections generation and the methodology definition is part of this program area goals. Based on previous studies in FY23, the size of microscopic cross section libraries increases rapidly with the number of tabulations, requiring significant amount of memory and drastically slowing down the Griffin calculations when evaluating cross sections via the multivariate linear interpolation approach. Rising to these challenges, this work investigates constructing Reduced-order Models (ROMs) for the multi-group microscopic cross sections to accelerate the cross section evaluation in Griffin. A database of multigroup cross sections is first collected considering all possible parameters that a designer could change for optimization. Down-selection of the ROM techniques afterward shows Deep Neural Network (DNN) as the best candidate when jointly consider memory efficiency, predictive accuracy, computational cost, scalability, flexibility and ease of implementation of the algorithms in comparison to the multidimensional interpolation. This work develops a specific interface that enables the cross section predictions using pre-trained DNN models into Griffin leveraging the existing ROM capabilities. DNNs have been trained for all isotopes for use in Griffin. Preliminary Griffin testing shows that DNNs exhibit exceptional predictive accuracy and the use of DNNs provides orders of magnitude improvement in memory efficiency compared to conventional interpolation techniques. With such ROM techniques, it holds great promise to further increase the fidelity of the Pebble Bed Reactor (PBR) simulation by increasing the number of tabulations/state variables during cross section evaluation, while maintaining the computational cost affordable in Griffin.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Effect of Surrogate Fission Products on Thermal Conductivity and Viscosity of NaCl-UCl 3

Thermophysical properties of salt systems relevant to molten salt reactors (MSRs) are experimentally measured in support of the US Department of Energy Office of Nuclear Energy (DOE-NE) MSR campaign within the Advanced Reactor Technology (ART) Program. These property measurements also support the development of the thermophysical arm of the Molten Salt Database (MSD) within DOE-NE’s Nu clear Energy Advanced Modeling and Simulation (NEAMS) Program. Several US Department of Energy (DOE) laboratories, including Oak Ridge National Laboratory (ORNL), have been capitalizing on modern methodologies and sample characterization techniques to conduct thermophysical property measurements to support these programs and to provide MSR developers and modelers with more recent and higher-quality data.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Transformational challenge reactor analysis to inform preconceptual core design decisions: Sensitivity study of transient analysis in a hydride-moderated microreactor

The Transformational Challenge Reactor (TCR) program aims to demonstrate a revolutionary design approach enabled by advanced manufacturing and data analytics in the design of nuclear reactors. This article discusses scoping analyses of preconceptual designs to inform TCR design decisions and the evaluation of sensitivities and uncertainties on postulated transient scenarios. The applicability of the systems codes TRACE and RELAP5-3D to TCR transient analysis are examined, and RELAP5-3D models are used to examine the transient response of two candidate core designs at multiple power levels. Then, the uncertainty quantification code RAVEN is used to quantify the effect of several design parameters on reactivity-initiated accident (RIA) progression at hot zero power (HZP) and hot full power (HFP) as well as to assess the impact of uncertainties in transient parameters for the pressurized loss of forced cooling (PLOFC).When results were compared, TRACE and RELAP5-3D showed good agreement in their ability to predict system behavior, but RELAP5-3D calculations were closer to analytical predictions for the RIA. Furthermore, models for a PLOFC accident in two designs (a UO2 and TRISO core) at multiple power levels showed greater temperature margins for the TRISO core at all power levels. Using this information, along with other scoping analyses and constraints, the TCR design team selected a power level of 3 MWth and a TRISO-based core design. For this design RAVEN was applied to vary RIA parameters in RELAP5-3D models at HZP and HFP to understand the effect on figures of merit such as peak power, fuel and coolant temperature, and energy deposition. This sensitivity study found that the inserted reactivity worth was the most important parameter controlling all figures of merit, but for insertion up to 1.5$ no failure of TCR fuel is anticipated. For constant reactivity insertions, the magnitude of the fuel temperature coefficient was found to have the greatest effect on all figures of merit under most circumstances. These results not only demonstrate the anticipated robust safety of the proposed TCR fuel form but also provide a reference for future metal-hydride moderated systems to understand RIA behavior. In the PLOFC, the impact of heat transfer enhancement due to wavy flow channel effects dominated the variance in peak temperatures, and variations in heat exchanger elevation provided the greatest control on natural circulation flow rate. Additionally, no fuel particle failure is anticipated in the PLOFC.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2026

Small Nuclear Reactors for Maritime Ports

Maritime ports are entering a period of sharply rising electricity demand as operations are electrified, shore power adoption grows, and energy-intensive industries expand near ports. This report evaluates the feasibility of small nuclear reactors at U.S. ports, which could offer stable baseload power and reduced dependence on regional grids. The report describes the current state of advanced reactor technologies and other factors important for future deployment such as safety and operations, siting requirements, regulatory environments and policy, and other co-benefit considerations. A structured evaluation across a diverse group of U.S. ports highlights the wide variation in feasibility. Fifteen ports were analyzed through port interviews and data collection to assess the port-specific conditions that most impact advanced reactor deployment. The analysis found that the most feasible ports for deployment have favorable geotechnical stability, supportive regulatory environments, and substantial energy loads in a grid-constrained environment. Additionally, an initial reactor size matching was done for the ports based on their reported energy consumption across different modes of operation. However, further analysis and detailed data will be required in the future to determine the optimal reactor-port matching. The economic viability to adopt this technology will be dictated by competitive cost of nuclear-generated electricity compared to other alternatives. Overall, small nuclear reactors present a promising but highly site-dependent pathway for ports seeking resilient, high-capacity energy solutions that support future energy demands. This report identifies key areas for future research and highlights ports that warrant further evaluation to assess the viability of small nuclear reactor implementation. By establishing these priorities, the analysis provides support for the development of informed strategies for potential advanced nuclear technology deployment. The inclusion of ports in this report does not imply their endorsement of nuclear energy generation, and the authors are grateful for the information, expertise, and perspectives they contributed.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2024

Energy Requirements for Integration of Nuclear Reactors with Iron and Steel Plants

This report identifies energy needs of heavy energy users within the domestic iron and steel industry and suggests solutions for integrating nuclear energy. The iron and steel industry, composed of several types of plants which perform different processes with varied energy demands and vectors, is a heavy consumer of electric power and fossil fuels including coke and natural gas. Almost all major process temperatures exceed the temperatures of direct heat available from advanced reactors, and so electricity and hydrogen were considered instead. Reference units were adopted and estimated energy demands computed for the blast furnace (BF), direct reduced iron (DRI) unit, electric arc furnace (EAF), and reheat furnaces. By utilizing production capacity data from industry reports, the ranges of power demands were estimated, including for hydrogen production by high temperature steam electrolysis (HTSE). For the EAF and DRI unit, more detailed integration studies with thermodynamic modeling were also conducted and determined a possible solution with a specific reactor design and number of modules. Furthermore, because many unit processes are co-located, entire plants were considered by adding the energy demands of the unit processes to form four hypothetical reference plants. The range of power needs for the reference plants is compatible with multi-unit banks of microreactors at the low end, and would create a need for multiple larger-capacity SMRs at the high end (1 GWe plus 0.14 GWt). Although the overall power need at the high end is well-matched with one present-day large reactor offering (1.1 GWe), redundancy considerations may require a minimum of two reactors, potentially eliminating the single large reactor from consideration. Auxiliary or house loads would increase the reference plant estimates. Finally, the report provides total estimated energy needs under integration of all U.S. units of each process (BF, DRI, EAF, and reheat furnaces), representing a national potential for nuclear energy in the industry. U.S. iron and steel plants may be candidates for integration with nuclear reactors via electricity and hydrogen, and many sites have energy requirements that correspond well to the capacities of several advanced nuclear power designs.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2021

Integrating Advanced Modeling and Accelerated Testing for a Modernized Fuel Qualification Paradigm

With the increasing interest in sodium fast reactor technology, as seen by applications to the U.S. Nuclear Regulatory Commission for the OKLO Aurora plant, fuel testing for the TerraPower Traveling Wave Reactor, and the impending construction and startup of the versatile test reactor (VTR), a modernized, accelerated approach to fuel qualification is needed. To guide this effort, a Phenomena Identification Ranking Table–styled analysis was performed for a U-Pu-Zr sodium-free annular fuel system. This analysis evaluated a series of fuel design properties and parameters against their contributions to key fuel performance phenomena. The resulting priority parameters were then reviewed against existing modeling and experimental capabilities to support investigation of the highest-priority parameters. A pathway for qualification was then established using highthroughput, high-volume experiments from MiniFuel and FAST in parallel with advanced physics-based model development. This effort outlines how the first stages of qualification can be reduced from the typical 20+-year development cycle to 5 to 7 years by deploying accelerated irradiation testing platforms. As with any accelerated test, these methods are prototypic in some aspects and less so in others; however, by coupling with advanced fuel performance modeling and simulation capabilities, the larger space of irradiation parameters and material response provided offers advantages for the validation of physics-based models supporting the deployment of novel fuel designs. As a test case, this paper utilizes a proposed Mark II fuel system for the upcoming VTR. Thus, an accelerated qualification method can be tested for the development of MARK II driver fuel so that by the time of VTR startup, lead test assemblies for a Mark II fuel can be initiated.

73 NUCLEAR PHYSICS AND RADIATION PHYSICS↗
DOE OSTI2025

Identifying Challenges in Safeguards for Metallic Fuel Fabrication Facilities

As new advanced reactors gain popularity, there is an increasing interest in metallic fuel fabrication for fast reactors. While metallic fuels themselves are not a new idea, as many of the first reactors employed metallic fuels, new designs, compositions, and fabrication methods are appearing throughout the nuclear community. As the interest grows and facilities are constructed, both domestic and international safeguards will need to be heavily involved to support safeguards-by-design (SBD) measures from the start. This work compiles a review of historical and modern fuel types and fabrication methods, fabrication processes, safeguards gaps, and potential safeguards solutions. Metallic nuclear fuel types have been around for many decades and were included in some of the first reactors including the Experimental Breeder Reactor (EBR)-I and -II, the Fermi 1 reactor, the Integral Fast Reactor (IFR), and the Dounreay Fast Reactor (DFR). These reactors used various compositions including pure uranium (U) metal, U-zirconium (Zr) alloys, plutonium (Pu)-aluminum (Al) alloys, U-fissium (Fs) alloys, U-Pu-Zr alloys, and U-molybdenum (Mo) alloys [1, 2, 3, 4, 5]. These small alloying additions are included to improve the material properties of the pure U metal. The alpha-phase U (stable below 661C) suffers elongation in one direction causing grain boundary cracking and increasing creep rate due to irradiation growth, thermal cycling, and preferential crystal orientation. It is ideal to utilize the gamma-phase U (typically stable above 769C) by adding small amounts of alloying elements such as Zr or Mo to stabilize this phase down to room temperature [3]. Additionally, some research has been focused on U with transuranic (TRU) elements present, typically coming from the used fuel recycling process. Including these elements in fast reactor fuel can aid in the reduction of nuclear waste by burning minor long-lived actinides. However, the additions of TRU elements can cause concerns to arise when trying to fabrication or safeguard metallic fuels. A typical metallic fuel element is shown in Figure 1. Sodium is added into the cladding to create a thermal bond between the fuel slug and cladding wall. The fuel slug is then inserted and the end plug is welded on to the top of the fuel element. A gas plenum is left to create a headspace for gaseous fission products to escape rather than continue to build in the fuel itself [1, 5]. Other fuel element geometries exist as well, such as the Lightbridge twisted cruciform geometry shown in Figure 2 [6]. This design allows for better cooling performance and provides room for fuel rod swelling without impacting the fuel rod diameter. There are many different fabrication methods for metallic fuels, which is one of the many benefits of these fuel types. Many of these fabrication methods are relatively easy and cost-efficient. The most popular fabrication method is injection casting, sometimes called vacuum induction melting (VIM), shown in Figure 3 [4, 8, 9, 7, 10]. This method was largely used for EBR-II fuel fabrication. The injection casting system is contained inside of a vessel consisting of a Y2O3-coated graphite crucible surrounded by an induction coil with ZrO2-coated quartz molds suspended above the crucible. The fuel feedstock is placed inside of the graphite crucible and melted using the induction furnace. The induction furnace utilizes a dual frequency with the high frequency melting the feedstock and the low frequency causing stirring of the melted feedstock to form a homogeneous mixture. The mixture is heated to approximately 1600C in an argon environment. The vessel is evacuated and then the quartz molds are lowered into the graphite crucible containing the molten metal and the vessel is repressurized to inject the metal fuel upwards into the molds. The molds are removed and then shattered to release the fuel slugs. This fabrication method was used to fabricate 39,000 metallic fuel pins for EBR-II. While injection casting has been the most common metallic fuel fabrication method throughout the decades, many other methods have been explored including low-pressure gravity casting, microwave casting, continuous casting, centrifugal casting, coextrusion, and many others [11, 12, 8, 13, 14, 15]. Some of these methods aim to mitigate challenges that arise with americium (Am) volatilization during the casting process for TRU-containing fuel feedstocks, an issue with injection casting. Coextrusion is one of the methods explored at the Idaho National Laboratory (INL) and has been utilized for the initial fabrication tests of Lightbridge's unique fuels, as well as other metallic fuels with cladding coextruded. In this process, large billets are formed and machined and then inserted into a molten salt bath for approximately 30 minutes. The billets are then loaded into the extrusion press and extruded. This process can be seen in Figure 4 [15].

11 - NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗
DOE OSTI2025

Decay heat analysis for advanced reactor spent fuel transportation and storage applications

Accurate characterization of nuclide inventories and decay heat in spent nuclear fuel is critical for ensuring its safe handling, storage, transportation, and disposal. Although extensive research has been conducted on light-water reactor fuel, advanced reactors present unique challenges due to their diverse core configurations, fuel characteristics, neutron energy spectra, and burnup levels. Building upon previous efforts that developed representative reactor core models for various advanced reactor types and fuels, this study evaluates reactor-specific decay heat characteristics. The results highlight significant variations across advanced reactor types as well as across reactor designs within the same reactor type, and they provide comparison to typical commercial light-water reactor fuel. For example, thermal-spectrum reactor fuels were observed to have an approximately 100-fold decrease in decay heat over the first decade of cooling, whereas the reduction was 10-fold for fast-spectrum reactor fuels. Mass-specific decay heat at discharge can differ by three orders of magnitude among the fast and thermal reactor systems considered. Overall, for the analyzed advanced reactor fuel, fewer than 17 nuclides account for over 99% of total decay heat at 0.5 years, and that number drops to fewer than 7 nuclides at 100 years of cooling. By quantifying reactor-specific decay heat trends and nuclide contributions, this work provides a technical basis to support the development of spent fuel management strategies for advanced reactor fuels as well as safety evaluations for storage, transportation, and long-term waste disposal.

Advanced reactors↗
DOE OSTI2023

Modeling Enhancements and Demonstration of Shift Capabilities for PBRs and MSRs

This technical report documents the modeling enhancements and demonstrations with the Shift Monte Carlo (MC) code targeted at pebble-bed reactors (PBRs) and molten salt reactors (MSRs) under the US Department of Energy (DOE) Nuclear Energy Advanced Modeling and Simulation (NEAMS) program in fiscal year (FY) 2023. The work performed included several enhancements, such as improvements for multigroup cross section generation, a new eigenvalue mode considering only prompt fission neutrons, and enhancements to the Titan frontend for Shift to allow for new geometry types and tally functionality. Additionally, new PBR equilibrium core search reference calculations were generated with Shift and compared to Serpent calculations provided by Idaho National Laboratory (INL). These enhancements provide a robust foundation for applying Shift for both reference and two-step neutronics analysis for advanced reactor simulation.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2023

Development and Porting of Nuclear Reactor Computational Models for the NRIC Virtual Test Bed in FY23

The U.S. DOE’s National Reactor Innovation Center (NRIC) hosts an open-source website and associated GitHub repository called the Virtual Test Bed (VTB) on which computational models for advanced reactors are documented and shared with the reactor community. In FY23 under the NRIC program, computational models for nuclear reactor analysis were developed and contributed to the VTB Github repository during FY23 by contributors at Argonne National Laboratory. Other models developed outside of NRIC were also ported to the VTB as part of this work, serving a broader mission to make computational reactor analysis models more widely available to the reactor community. The model development activities focused on demonstration of gas-cooled microreactor models including computational fluid dynamics simulations of flow through an industry-inspired air jacket design, and simulation of multiphysics transients for a gas-cooled microreactor assembly. Additionally, development of a molten salt reactor (led at Idaho National Laboratory) was supported through Argonne’s expertise in multigroup cross sections generation. Models for these two reactor types were targeted due to their relevancy to NRIC’s Demonstration of Microreactor Experiments (DOME) and Laboratory for Operation and Testing in the U.S. (LOTUS) physical test beds, which are slated to host microreactor and molten salt reactor experiments. The model porting activities consisted of developing detailed documentation for several physics models which originate from the Nuclear Energy Advanced Modeling and Simulation (NEAMS) program. We include only contributions from Argonne National Laboratory in this report.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

Integrated Molten Salt Reactor Modeling Capabilities in NEAMS Thermal Hydraulics Tools

The DOE Nuclear Energy Advanced Modeling and Simulation (NEAMS) program supports a full range of computational thermal fluids analysis capabilities and code developments for a broad range of advanced reactor concepts. The research and development approach under the thermal fluids technical area synergistically combines three length and time scales in a hierarchical multi-scale approach. To enable multi-scale thermal fluids capability using these codes, a key joint effort has been underway to develop an integrated system- and engineering-scale thermal fluids analysis capability, through integration of SAM and Pronghorn codes, both based on the MOOSE framework.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗
DOE OSTI2025

High-resolution characterization of ceramic-metal interface of TiN coating on ferritic-steels for nuclear application

Advanced fuel cladding is critical for fast reactors, offering sufficient thermal conductivity, mechanical and dimensional stability and radiation tolerance of the cladding base material. Additionally, it must provide corrosion resistance and high temperature coolant compatibility on the cladding outer surface, as well as chemical stability on the cladding inner wall against fuel cladding chemical interaction (FCCI). TiN ceramic coating has been considered an effective diffusion barrier for inner and outer cladding-walls for enhanced performance. The TiN-metal interface microstructure and chemistry play a critical role in coating bond strength and integrity under harsh conditions. High-resolution transmission electron microscopy characterization of ceramic-metal interface at atomic resolution in unirradiated, irradiated and thermal cycled conditions were performed. The interface remained intact after irradiation up to 200 dpa or thermal cycling five times up to 550 °C. In conclusion, this work discusses the potential impact of these results on coating performance and design for advanced claddings.

36 - MATERIALS SCIENCE↗