Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “Additives”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 793 records · Page 44

Feasibility Study to Dissolve Additively Manufactured Inconel 718 Support Structures

Additive manufacture (AM) component design face constrains due to support structure removal. Interior passages or delicate geometries require supports yet cannot be removed without compromising the design or complicating post-processing. A process was developed to dissolve metal AM supports where a sensitizing agent is applied post-build. During stress relief the sensitizing agent diffuses into the surface and alters the chemical composition of the top 100 to 200 μm. During an electrochemical dissolution process the sensitized region is susceptible to corrosion/dissolution and the etching reaction self-terminates once the sensitized region is dissolved. Support thickness varies from 80 to 200 μm, resulting in total dissolution or sufficiently weakened to facilitate removal. The objective of this project was to demonstrate a support structure dissolution process for IN718 components built using AM and to characterize the impact on mechanical properties, microstructure, and surface finish.

Omar R Mireles↗

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultra-fine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray micro-focus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗

Al-Cu-Zn-Mg Alloy for Additive Manufacturing by Electron Beam Deposition

The application of fusion-based additive manufacturing (AM) to aircraft structural components is limited by the lack of high-strength aluminum alloys optimized for AM processing. High strength aluminum alloys (such as 7050-T7451) are difficult to process by AM because of their solidification cracking susceptibility and loss of volatile alloying elements such as Zn and Mg. The performance of a proprietary Al-Cu-Zn-Mg alloy wire feedstock was evaluated for AM utilizing electron beam deposition. Deposit microstructure, composition, occurrence of porosity and cracking, and post-heat treatment tensile and fracture toughness were correlated with deposition parameters. Post-heat treatment strength, ductility, and fracture toughness were lower than typical values for wrought 7050-T7451, related to significant losses of Zn and Mg and to porosity. Recommendations are offered for modifications to wire feedstock composition and adjustments to deposition conditions and heat treatment to enable AM of electron beam deposited material that has strength comparable to 7050-T7451 wrought products.

Al-Cu-Zn-Mg alloy, electron beam deposition, mecha↗

Additive Manufactured Ultra-Fine Lattice Structures for Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar R Mireles↗

Additive Manufacture of Ultra-Fine Lattice Structures of Green Propulsion Catalysts

Traditional mono-propulsion catalysts consist of coated ceramic or graphite foams that possess anisotropic mechanical and fluid properties limiting design, cost, availability, and operational use. Ultra-fine lattice structures are repeating unit cells with ligament thickness as small as 100 μm produced via Additive manufacture (AM). These lattice structures have the potential to replace coated foams used in a mono-propellant system catalysts. AM ultrafine lattice structures are designed to mimic the operational intent of coated foams but with improved design flexibility, compressive strength, and flow behavior printed from into a single part directly from the preferred platinum metal alloy. The investigation objective was to conduct feasibility studies of AM ultra-fine lattice structures capable of replacing coated foams with superior functionality. NASA MSFC identified desired lattice characteristics and created designs while EOS developed optimized laser powder bed fusion AM parameters to manufacture Ti6Al4V and tungsten specimens. Optimized designs, computational tools, AM parameters, and post-process methods were developed. Specimens underwent x-ray microfocus CT, metallographic inspection, compression testing, and flow testing. Results demonstrate that AM ultra-fine lattices improved geometric and performance repeatability with the potential for significantly increased availability while decreasing cost and lead time.

Omar Mireles↗

Convolutional Neural Networks for Image Classification in Metal Selective Laser Meting Additive Manufacturing

Selective laser melting (SLM) is a metal additive manufacturing process that has several advantages such as the large range of metal materials that can be accommodated, 3D printing of complex shape components, the ability to adjust material properties, and cost reduction as expensive production equipment may not be required. Therefore, process monitoring is crucial in different stages of the component building. In this work, convolutional neural networks (CNNs) are investigated as a suitable technique for post-inspection of builds. The monitoring of manufactured parts was conducted by collecting computed tomography (CT) images and identifying defects. Five CNN models were implemented and tested for the classification of the CT images. The models were based on NASNetMobile and DenseNet121, and a custom built CNN model. The results of this work show that CNNs can be feasible and reliable for rapid monitoring and classification of defects in CT images from build fabrication using SLM.

Rodolfo Ledesma↗

Additive Manufacture of Porous ZrC for NTP In-Core Insulators

Nuclear Thermal Propulsion (NTP) requires the use of in-core insulators to manage to thermal environment between high temperature fuel elements and lower temperature structural components. The unforgiving in-core operating conditions severely limit potential material candidates. Zirconium Carbide (ZrC) is a promising candidate due to a high melting temperature, high compressive strength, hardness, wear resistance, hydrogen compatibility, and low neutron absorption cross sections. However, fully dense ZrC is not an insulator but it has been found that the thermal conductivity of ZrC decreases by increasing porosity to approximately 60 % theoretical density (%TD). Previous methods for generating porous ZrC were difficult, expensive, and time consuming. Binder jet additive manufacture (AM) can print ceramic materials to near net shape. Binder jet AM is not utilized in many applications due to an inherently low post-sintering density on the order of 60 %TD. For this specific application the inherent lower density is leveraged as an advantage in production porous ZrC in order to control the thermal conductivity. A feasibility study was conducted to investigate binder jet AM parameter development for ZrC, heat treatment optimization (burn-out and sinter), microstructural characterization, mechanical testing, and thermal testing to generate near-net shape ZrC components with ~60 %TD with the desired thermal conductivity and mechanical strength.

Omar Mireles↗

Additive Manufacture of Refractory Metal Green Propulsion Thrusters

High temperature refractory metals are required for a number of high temperature propulsion applications. Refractory metals are expensive, difficult to manufacture with high buy-to-fly ratios, and few vendors. Additive manufacture (AM) is used to produce C103, Molybdenum (Mo), and Tungsten (W) reaction chamber and thrust stand-off as well as Iridium ultra-fine lattice catalysts for integration into 1 N green propulsion thrusters. After printing components underwent post-processing to include heat treatment, surface finish modification, inspection, integration, and testing. Properly utilized AM overcomes existing manufacture limitations by greatly increasing design flexibility, material options, decrease price, decrease lead-time, and increase the commercial supply base.

Omar Mireles↗

A Study of Particle Size Metrics Using Non-Spherical Feedstock for Metal Additive Manufacturing

The goal of this work was to determine which standard particle size metric derived from optical analysis most closely approximates the sieved weight percent of irregularly shaped powder intended to be used for directed energy deposition. In this investigation, equivalent circle diameter, maximum diameter, minimum diameter, and perimeter are used as metrics to “virtually sieve” the particles in samples of irregularly shaped powder into the following particle size bins: <45 µm, 45 µm - 150 µm, and >150 µm. The percentage in the 45 µm - 150 µm bin is then compared to the weight percent of the powder mechanically sieved into this size range. The absolute difference between the virtually sieved percentage and the mechanically sieved percentage was assessed for 81 samples of mechanically-generated stainless steel 316L powder all produced under different processing conditions in an oscillation ball mill. This difference was found to be on average, the least with the minimum diameter assessed as an area percentage, followed by the equivalent diameter assessed as an area percentage, and then the maximum diameter assessed as a percentage of the total number of particles ranked third. These findings may be used by powder production process engineers and quality assurance personnel to assist in process control as more diverse additive manufacturing feedstocks become utilized.

Marcus Jackson↗

Responses of Florida Scrub Vegetation to Water Additions from a Groundwater Treatment Project and to Hurricane Disturbance

Florida scrub is a fire-maintained shrub vegetation of well-drained, sandy soils; dominant species include several species of Quercus and Serenoa repens. In a remediation project, treated groundwater was distributed through an exfiltration gallery into intact scrub. We established eight permanent line-intercept transects (15 m length) in the site in April 2002, four close to the exfiltration gallery and four more distant from it. We sampled vegetation, < 0.5 m and ≥ 0.5 m, along each transect and measured vegetation height at four points (0, 5, 10, 15 m) annually through 2019. The initial phase of the project operated from October 2002 to early March 2004 (494 days) and distributed 1.74 x 10^8 L of water. The final phase of the project occurred from March 2005 through August 2008 (1251 days) and distributed 1.90 x 10^8 L of water. Pumping raised the water table near the exfiltration gallery. Vegetation height did not differ between the near and far transects initially. Vegetation height increased in the near transects by 2004 with the greatest percent change in 2003 and 2004 as did total cover ≥ 0.5 m. Total cover < 0.5 m and bare ground were similar initially in the near and far transects and declined in the near transects by 2004. Scrub species, particularly the dominant scrub oaks, increased height and cover in response to water additions with no loss of dominant scrub species and no establishment of mesophytes. Hurricane Frances (September 2004) reduced cover ≥ 0.5 m the following year. Hurricane Matthew (October 2016) and Hurricane Irma (September 2017) caused greater damage including breaking limbs as reflected in reduced height and total cover ≥ 0.5 m probably because the older, taller scrub was more vulnerable to wind damage.

Florida scrub↗

In-Situ Alloying of GRCop-42 via Additive Manufacturing: Precipitate Analysis

GRCop-42, a Cu-4at% Cr-2at% Nb alloy, was designed as a high temperature, high strength, high heat flux material for rocket engine combustion chamber liners by NASA Glenn Research Center. In situ alloying of GRCop-42 (ISGRCop-42) using powder bed fusion (PBF) additive manufacturing (AM) takes elemental powders of Cu, Cr, and Nb to be introduced into the PBF environment and develop the GRCop alloy while simultaneously building an AM component. Elemental powders were milled together prior to printing in an effort to facilitate the alloying process. Success of the in situ alloying process may provide lower cost, faster lead times, alloying optimization, and more design freedom in the development of regeneratively-cooled rocket propulsion systems. Evaluation of the ISGRCop-42 was conducted using a phase extraction procedure to isolate the Cr2Nb precipitates from the pure Cu matrix. The isolated precipitates were then examined using x-ray powder diffraction (XRD), scanning electron microscopy (SEM), and energy dispersion spectroscopy (EDS). It was found that ISGRCop-42 successfully and repeatedly formed Cr2Nb at a yield as high as 89% of potential Cr2Nb. Further, it was identified that the preparation of the powder was the most influential factor in alloying success, and the second most influential factor was the laser power.

In Situ alloying↗

The Effect of Composition on Microstructure and Properties for Additively Manufactured Superalloy 718

Additive manufacturing (AM) represents an exciting new approach towards producing metallic aerospace components. The ability to make complex geometries that were impossible to create using conventional manufacturing methods has sparked interest from the aerospace community, including NASA. The use of AM components for crucial and human rated space missions necessitates a full characterization of the differences between AM and more conventional wrought and cast processes. For this study, sixteen different commercially available superalloy 718 powder feedstocks were obtained, built using laser powder bed fusion(L-PBF), and microstructurally and mechanically analyzed. These measurements revealed a wide range of build qualities and microstructures despite all powder lots falling within the 718chemical specification and being processed using the same prescribed build and heat treatment parameters. Statistical analysis found a strong correlation of the amount of carbon in the powder with the final grain size and strength of the heat-treated 718 part. Ultimately, this study highlights the need of a refined superalloy 718 chemical specification for powder lots to be used in AM.

Timothy M Smith↗

Global Reference Atmospheric Model (GRAM) Advancements and Additions

Introduction:The Global Reference Atmospheric Model (GRAM) is one of the most widely used engineering models of the atmosphere. GRAM development and maintenance has been led by NASA Marshall Space Flight Center (MSFC). The NASA Science Mission Directorate (SMD) has provided funding support to upgrade the GRAMs since Fiscal Year 2018. NASA Langley Research Center has been working with MSFC on the upgrades.This presentation will provide details regarding the upgrades that have been made to the existing GRAMs, the development of new GRAMs, as well as the ongoing objectives, tasks, and milestones re-lated to the GRAM upgrades funded by NASA SMD. GRAM: The GRAMs are engineering-oriented atmospheric models that estimate mean values and statistical variations of the atmospheric properties for numerous planetary destinations.They provide mean values and variability for any point in the atmosphere as well as seasonal, geographic, and altitude variations. GRAM outputs include atmospheric density, temperature, pressure, winds, and chemical composition along a user-defined path.Theyhave been widely used by the engineering community because of their ability to create realistic dispersions. GRAMs have been integrated into high fidelity flight dynamic simulations of launch, entry, descent and landing (EDL), aerobraking and aerocapture. MSFC has been developing and updating GRAMs since 1974; GRAMs are currently available for Earth, Mars, Venus, Neptune, and Titan. GRAM Upgrade Status: Code Moderization.The planetary GRAMs are being rearchitected from Fortran to a common object-ori-entedC++ framework called the GRAM Suite. This new architecture creates a common GRAM library of data models and utilities. The first C++ releases of the existing planetary GRAMs (Mars, Venus, Neptune, and Titan-GRAM) in the GRAM Suite are straight conversions from the latest Fortran version. Model Upgrades.The focus of the model upgrade task is to improve the atmosphere models in the existing GRAMs and to establish a foundation for developing GRAMs for additional destinations. The GRAM ephemerishas been upgraded to the NASA Navigation and Ancillary Information Facility (NAIF) SPICE toolkit (version N0066). The calculation of the speed of sound has also been improved in the GRAMs. The GRAM team has received updated Mars General Circulation Model (MGCM) datasets from NASA Ames Research Center. Mars Global Ionosphere-Thermosphere Model (M-GITM) data is being obtained toreplace the Mars Thermospheric General Circulation Model (MTGCM) data in legacy Mars-GRAM. M-GITM and updated MGCM data will be incorporated into a future GRAM Suite release.Twoprojects that will improve the atmospheric model data in the GRAMs have been funded by the GRAM team since Fiscal Year 2020. Sanjay Limaye and Patrick Fry at the University of Wisconsin are reanalyzing the Venus Express radio occultation observations and analyzing the Akatsukiradio occultation observations.This will lead tothe calculation of number density, temperature, and pressure profiles for the 40-90 km altitude range. Kunio Sayanagi, Justin Garland, and Ryan McCabeat Hampton University are developing empirical global models for Venus,Jupiter, Saturn, Uranus, Neptune, and Titan that incorporates the latest data available for each of these planetary destinations. Upgraded GRAM Releases. GRAM Suite Version 1.0 was released in May 2020 and contains the rearchitected Neptune-GRAM, including the common GRAM framework and planet–specific code. GRAM Suite Version 1.1 was released in September 2020 and addedthe rearchitected Titan-GRAM to the GRAM Suite. A User Guide and Programmer’s Manualarereleased with all GRAMs. The rearchitected Mars and Venus-GRAMs will be released in upcomingversions of the GRAM Suite. New GRAM Releases. New GRAMs have been de-veloped for Uranus and Jupiter. Uranus-GRAM is based on an individual profile generated by Gary Allen (ARC) from Voyager 2 occultation data and will be released in GRAM Suite Version 1.2. Jupiter-GRAM is based on individual profile produced from Al Seiff’s Ju-piter model[1].Jupiter-GRAM will be released in GRAM Suite Version 1.3. Saturn-GRAM is currently under development and will be released in a future version of the GRAM Suite. Conclusions: GRAMs are vital and frequently used toolsets. Releases of the GRAM Suite, upgrades of the existing planetary GRAMs, and development of new planetary GRAMs are ongoing. NASA SMD funding has been essential to addressing current limitations and accomplishing GRAM developmental goals. Continua-tion ofSMD fundingwill ensure the development, up-grades, and maintenance of the GRAMs. References: [1] Seiff, A., et al. (1998) JGR, 103, 22,857-22,889. Acknowledgments: The authors gratefully acknowledge support from the NASA SMD

atmospheric models↗

Hot Isostatic Pressing for Reduction of Defects in Additively Manufactured Inconel-718 Preliminary Simulation Approach and Results

Selective laser melting (SLM) of Inconel-718 (IN718) is a promising advanced manufacturing technology; however, challenges exist for fracture-critical parts where pores induced during the manufacturing process reduce fatigue life of the material. Hot isostatic pressing (HIP) is a common post processing technique used to reduce the part porosity by exposing parts to high temperature and pressures. Pore closure depends on the pore shape, trapped gas, and HIP parameters, and the process can only be optimized by understanding the effect of these variables. An analysis capability is described to better understand the conditions necessary for pore closure, and the effect of several variables on porosity are explored and compared to a baseline case. The importance of valid material response models is identified as a significant factor in model accuracy; especially the creep material response model which, in the baseline case, predicts that creep strain accounts for 87.7% of the total strain at the conclusion of the HIP cycle. Lessons learned are described, in addition to future work including model validation.

Joshua M Fody↗

Backshell Thermal Protection Materials for Additive Manufacturing

NASA invests in additive manufacturing (AM) to enable new mission architectures and design methods, including autonomous fabrication. AM is suited for backshell thermal protection materials that require many complex closeouts that lead to integration challenges. Current work will review printable backshell thermal protection material formulation, development, and characterization, such as Arc-jet testing results.

Tane Boghozian↗

(Preliminary) Effects of Ball Milling Zeolite Powders for Use in Additively Manufactured Solid Sorbents

Zeolite 13X is favorable to be used as an adsorbent in carbon dioxide (CO2) removal from the spacecraft cabin air. Reducing the size of the zeolite particles and particle size distribution is thought to increase the capacity of CO2 adsorption of the zeolite 13X powder, and potentially increase its manufacturability as a paste for additive manufacturing or slip casting. This paper will go into detail on the process of using ball milling in order to reduce particle size and particle size distribution of commercial zeolite 13X powder, as well as to characterize CO2 adsorption and manufacturability of the milled powder. Both dry and wet ball milling was analyzed during the experiment. Studies were also ran on the amount of time the powder was milled, rotational speed of the milling machine, ball to powder ratio, ball to jar ratio, and ethanol to powder ratio. The processed powder was then characterized through laser diffraction, SEM, and surface measurement techniques to show that particle size and particle size distribution could be reduced, and to show the effect of the reduced particle size and particle size distribution on CO2 adsorption and manufacturability.

zeolite↗

Backshell Thermal Protection Materials for Additive Manufacturing

Leveraging AM technology focused on the Fused Deposition Modeling (FDM) process could automate the heat shield manufacturing process and allow it to reduce cost and build time and improve the design to 3D print and process TPS materials directly on the structure in monolith segments. Furthermore, AM allows the production of complicated three-dimensional geometry and density gradient layers without custom molds or special tools. NASA invests in additive manufacturing (AM) to enable new mission architectures and design methods; AM is suited for backshell thermal protection materials that require many complex closeouts that lead to integration challenges. Current work will review backshell thermal protection material formulation, development, and characterization.3D printer was used to 3D print arc-jet test coupons. The coupons were tested at the NASA Ames arc jet facility, and the results show promising properties compared with the heritage materials.

Tane Boghozian↗