Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “yield point”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Whiskers, cones and pyramids created in sputtering by ion bombardment

A thorough study of the role which foreign atoms play in cone formation during sputtering of metals revealed many experimental facts. Two types of cone formation were distinquished, deposit cones and seed cones. Twenty-six combinations of metals for seed cone formation were tested. The sputtering yield variations with composition for combinations which form seed cones were measured. It was demonstrated that whisker growth becomes a common occurrence when low melting point material is sputter deposited on a hot nonsputtered high melting point electrode.

Wehner, G. K.↗

A method to estimate critical volumes

Methods for estimating the volume of the critical temperature used for the estimation of thermodynamic properties of substances are described. The possibility to estimate the critical temperature by using a combination of only eighteen atomic and structural contributions is shown. These contributions are listed and the critical temperature is given by a linear expression. By comparing the Vetere (1976) and Lydersen (1955) methods with the method discussed it is noted that while all three methods yield about the same average error (about 3%), the new method is superior in that it requires a smaller number of increments to fit data points.

Fedors, R. F.↗

Analog Video Image-Enhancing Device

Inexpensive system yields pseudo-three-dimensional effect. Includes video camera with lens, connected to video monitor for analog video enhancement. Video signal obtained from monitor at point beyond where synchronization signals are detected, eliminating need to regenerate composite video signal. Analog video image-enhancing device improves appearance of technical photographs by selectively compressing overall dynamic ranges while accentuating edges or small details of greatest interest.

Weinstein, L. M.↗

Amorphous silicon photovoltaic modules and test devices design, fabrication and testing

In July of 1984, Hughes and JPL initiated a contract for Hughes to design, fabricate and test 10 thin film Amorphous Silicon (a-Si) photovoltaic power modules. These modules were to be 1 ft x 4 ft in size. They were to be preceded by the delivery of 10 a-Si 4 in. square test devices. This effort is very timely since thin film PV development has progressed to the point where intermediate load power applications are on the horizon. It is important to know if current a-Si submodule design and manufacturing processes yield a product that is compatible with the packaging needed to meet a 20 to 30 year life span expectancy. The term submodule is assigned to an interconnected assembly of 28 a-Si cells deposited on a 1 foot square glass superstrate. These assemblies are equipped with electrical terminations, i.e., copper tabs at the four corners of the inverted submodules. It is these submodules that are to be interconnected and packaged into power modules, as opposed to the interconnected individual crystalline cells packaged into todays PV modules. A discussion of the fabrication methods and results follows.

Vanleeuwen, M.↗

The observation of possible reconnection events in the boundary changes of solar coronal holes

Coronal holes are large scale regions of magnetically open fields which are easily observed in solar soft X-ray images. The boundaries of coronal holes are separatrices between large scale regions of open and closed magnetic fields where one might expect to observe evidence of solar magnetic reconnection. Previous studies by Nolte and colleagues using Skylab X-ray images established that large scale (greater than or equal to 9 x 10(4) km) changes in coronal hole boundaries were due to coronal processes, i.e., magnetic reconnection, rather than to photospheric motions. Those studies were limited to time scales of about one day, and no conclusion could be drawn about the size and time scales of the reconnection process at hole boundaries. Sequences of appropriate Skylab X-ray images were used with a time resolution of about 90 min during times of the central meridian passages of the coronal hole labelled Coronal Hole 1 to search for hole boundary changes which can yield the spatial and temporal scales of coronal magnetic reconnection. It was found that 29 of 32 observed boundary changes could be associated with bright points. The appearance of the bright point may be the signature of reconnection between small scale and large scale magnetic fields. The observed boundary changes contributed to the quasi-rigid rotation of Coronal Hole 1.

Kahler, S. W.↗

The observation of possible reconnection events in the boundary changes of solar coronal holes

Coronal holes are large scale regions of magnetically open fields which are easily observed in solar soft X-ray images. The boundaries of coronal holes are separatrices between large-scale regions of open and closed magnetic fields where one might expect to observe evidence of solar magnetic reconnection. Previous studies by Nolte and colleagues using Skylab X-ray images established that large-scale (more than 90,000 km) changes in coronal hole boundaries were due to coronal processes, i.e., magnetic reconnection, rather than to photospheric motions. Those studies were limited to time scales of about one day, and no conclusion could be drawn about the size and time scales of the reconnection process at hole boundaries. Sequences of approximate Skylab X-ray images with a time resolution of about 90 min are here used during times of the central meridian passages of the coronal hole labelled 'Coronal Hole 1' to search for hole-boundary changes which can yield the spatial and temporal scales of coronal magnetic reconnection. It is found that 29 of 32 observed boundary changes could be associated with bright points. The appearance of the bright point may be the signature of reconnection between small-scale and large-scale magnetic fields. The observed boundary changes contributed to the quasi-rigid rotation of Coronal Hole 1.

Kahler, S. W.↗

Experimental segregation of iron-nickel metal, iron-sulfide, and olivine in a thermal gradient: Preliminary results

Speculation about the possible mechanisms for core formation in small asteroids raises more questions than answers. Petrologic evidence from iron meteorites, pallasites, and astronomical observations of M asteroids suggests that many small bodies were capable of core formation. Recent work by Taylor reviews the geochemical evidence and examines the possible physical/mechanical constraints on segregation processes. Taylor's evaluation suggests that extensive silicate partial melting (preferably 50 vol. percent or greater) is required before metal can segregate from the surrounding silicate and form a metal core. The arguments for large degrees of silicate partial melting are two-fold: (1) elemental trends in iron meteorites require that the metal was at is liquidus; and (2) experimental observations of metal/sulfide inclusions in partially molten silicate meteorites show that the metal/sulfide tends to form spherules in the liquid silicate due to surface tension effects. Taylor points out that for these metal spherules to sink through a silicate mush, high degrees of silicate partial melting are required to lower the silicate yield strength. Although some qualitative experimental data exists, little is actually known about the behavior of metals and liquid sulfides dispersed in silicate systems. In addition, we have been impressed with the ability of cumulative olivine to expel trapped liquid when placed in a thermal gradient. Consequently, we undertook to accomplish the following: (1) experimentally evaluate the potential for metal/sulfide/silicate segregation in a thermal gradient; and (2) obtain quantitative data of the wetting parameters of metal-sulfide melts among silicate grains.

Jurewicz, Stephen R.↗

Captain, sensors report ...: Correction of Remote Sensing Data

Remote sensing data acquired by airborne and satellite Systems have many impressive virtues for ecology and other sciences. They are synoptic. They are extremely cheap per data point. They cover large areas. They are not subjective. They detect features that are of clear and obvious interest for many uses. But, they also yield totally irreproducible measurements. Sensors that operate in the visible, near infrared and thermal portions of the spectrum are sensitive to a host of phenomena that are usually of little interest to the average user. Fully recognizing the power and sophistication of the algorithms currently available to users of remote sensing, the authors as long time developers (20+ years) of such algorithms, demonstrate that a host of other signals are convolved with the typical data set, and that many of these signals are very commonly not even recognized, and that these signals are often larger than the signal from the putative target. These derive from both geometric and radiometric sources as well as fundamental flaws in sensor engineering. Until such extraneous factors can be controlled or eliminated the utility of the data is greatly restricted. Finally, the authors lay out a design elements for a rational sensor and methods of deconvolving the complexity of the real world data using such a sensor.

Rickman, Doug↗

Extraction of Airport Features from High Resolution Satellite Imagery for Design and Risk Assessment

The LPA Group, consisting of 17 offices located throughout the eastern and central United States is an architectural, engineering and planning firm specializing in the development of Airports, Roads and Bridges. The primary focus of this ARC project is concerned with assisting their aviation specialists who work in the areas of Airport Planning, Airfield Design, Landside Design, Terminal Building Planning and design, and various other construction services. The LPA Group wanted to test the utility of high-resolution commercial satellite imagery for the purpose of extracting airport elevation features in the glide path areas surrounding the Columbia Metropolitan Airport. By incorporating remote sensing techniques into their airport planning process, LPA wanted to investigate whether or not it is possible to save time and money while achieving the equivalent accuracy as traditional planning methods. The Affiliate Research Center (ARC) at the University of South Carolina investigated the use of remotely sensed imagery for the extraction of feature elevations in the glide path zone. A stereo pair of IKONOS panchromatic satellite images, which has a spatial resolution of 1 x 1 m, was used to determine elevations of aviation obstructions such as buildings, trees, towers and fence-lines. A validation dataset was provided by the LPA Group to assess the accuracy of the measurements derived from the IKONOS imagery. The initial goal of this project was to test the utility of IKONOS imagery in feature extraction using ERDAS Stereo Analyst. This goal was never achieved due to problems with ERDAS software support of the IKONOS sensor model and the unavailability of imperative sensor model information from Space Imaging. The obstacles encountered in this project pertaining to ERDAS Stereo Analyst and IKONOS imagery will be reviewed in more detail later in this report. As a result of the technical difficulties with Stereo Analyst, ERDAS OrthoBASE was used to derive aviation obstruction measurements for this project. After collecting ancillary data such as GPS locations, South Carolina Geodetic Survey and Aero Dynamics ground survey points to set up the OrthoBASE Block File, measurements were taken of the various glide path obstructions and compared to the validation dataset. This process yielded the following conclusions: The IKONOS stereo model in conjunction with Imagine OrthoBASE can provide The LPA Group with a fast and cost efficient method for assessing aviation obstructions. Also, by creating our own stereo model we achieved any accuracy better currently available commercial products.

Robinson, Chris↗

Growth and photosynthetic responses of wheat plants grown in space

Growth and photosynthesis of wheat (Triticum aestivum L. cv Super Dwarf) plants grown onboard the space shuttle Discovery for 10 d were examined. Compared to ground control plants, the shoot fresh weight of space-grown seedlings decreased by 25%. Postflight measurements of the O2 evolution/photosynthetic photon flux density response curves of leaf samples revealed that the CO2-saturated photosynthetic rate at saturating light intensities in space-grown plants declined 25% relative to the rate in ground control plants. The relative quantum yield of CO2-saturated photosynthetic O2 evolution measured at limiting light intensities was not significantly affected. In space-grown plants, the light compensation point of the leaves increased by 33%, which likely was due to an increase (27%) in leaf dark-respiration rates. Related experiments with thylakoids isolated from space-grown plants showed that the light-saturated photosynthetic electron transport rate from H2O through photosystems II and I was reduced by 28%. These results demonstrate that photosynthetic functions are affected by the microgravity environment.

NASA Discipline Plant Biology↗

Gamma Ray Burst Discoveries by the Swift Mission

With 3 years of on-orbit operations (launched in Nov 2004), Swift has detected over 300 gammaray bursts (GRBs). The unique combination of quick and accurate position determinations by the BAT instrument, fast autonomous spacecraft slewing, and multi-band instrumentation (XRT and UVOT) has allowed Swift to accumulate a long list of discoveries about GRBs. These positions are also available to the ground follow-up community (via TDRSS and GCN) within 15-30 sec. A summary of these discoveries will be given (e.g. long and short GRB host associations, SN associations, flaring and on-going activity in the central engine). The Swift spacecraft and instruments are in fine working order with no signs of performance degradation. With an expected orbital lifetime well past 2020, the overlap with GLAST (launch in mid-2008) will yield greater than 30 GRBs/year with observations by both missions. This will provide an unprecedented wavelength coverage from optical to 100 GeV. The coordination of pointing Swift with GLAST will be described.

Barthelmy, Scott↗

Accurate ab initio Quartic Force Fields of Cyclic and Bent HC2N Isomers

Highly correlated ab initio quartic force field (QFFs) are used to calculate the equilibrium structures and predict the spectroscopic parameters of three HC2N isomers. Specifically, the ground state quasilinear triplet and the lowest cyclic and bent singlet isomers are included in the present study. Extensive treatment of correlation effects were included using the singles and doubles coupled-cluster method that includes a perturbational estimate of the effects of connected triple excitations, denoted CCSD(T). Dunning s correlation-consistent basis sets cc-pVXZ, X=3,4,5, were used, and a three-point formula for extrapolation to the one-particle basis set limit was used. Core-correlation and scalar relativistic corrections were also included to yield highly accurate QFFs. The QFFs were used together with second-order perturbation theory (with proper treatment of Fermi resonances) and variational methods to solve the nuclear Schr dinger equation. The quasilinear nature of the triplet isomer is problematic, and it is concluded that a QFF is not adequate to describe properly all of the fundamental vibrational frequencies and spectroscopic constants (though some constants not dependent on the bending motion are well reproduced by perturbation theory). On the other hand, this procedure (a QFF together with either perturbation theory or variational methods) leads to highly accurate fundamental vibrational frequencies and spectroscopic constants for the cyclic and bent singlet isomers of HC2N. All three isomers possess significant dipole moments, 3.05D, 3.06D, and 1.71D, for the quasilinear triplet, the cyclic singlet, and the bent singlet isomers, respectively. It is concluded that the spectroscopic constants determined for the cyclic and bent singlet isomers are the most accurate available, and it is hoped that these will be useful in the interpretation of high-resolution astronomical observations or laboratory experiments.

Inostroza, Natalia↗

Tungsten erosion during L-mode discharges in the DIII-D SAS-VW divertor

A series of L-mode plasma discharges was performed in the DIII-D tokamak to assess the impact of outer strike point (OSP) position and toroidal magnetic field direction on erosion and core contamination potential of the recently-installed, tungsten-coated Small Angle Slot (SAS-VW) divertor. In one discharge, in-slot emission spectroscopy measured an<48 % increase in the W gross erosion rate when the OSP was moved 3 cm outwards, away from the V-shaped vertex of the slot divertor. However, the effective W yield (erosion rate divided by the incident D flux) was, overall, insensitive to changes in OSP location. Consistently low estimates of the effective W yield based on measurements taken a few cm outwards from the vertex suggest potentially significant C surface contamination. No W emission signal was detected when orienting the toroidal magnetic field such that the ion B×∇B drift direction is pointed away from the X-point. However, measurements of W content in the plasma core for both toroidal magnetic field directions suggest the presence of additional, unmeasured sources of erosion. The difference in the measured core W density with OSP position is much greater than the difference in the measured erosion rates, which may suggest that the leakage of eroded impurities out of the divertor is governed primarily through the parallel ion temperature gradient and friction forces.

70 PLASMA PHYSICS AND FUSION TECHNOLOGY↗

Production and Catalytic Upgrading of 2,3-Butanediol Fermentation Broth into Sustainable Aviation Fuel Blendstock and Fuel Properties Measurement

With the increasing demand for sustainable supplies of aviation fuel and need to address climate change, new conversion technologies are needed to efficiently process biomass, produce high quality jet fuel blendstock, and meet carbon emission targets. This study demonstrates the synthesis, conditioning, and catalytic upgrading of 2,3-butanediol (BDO) fermentation broth into a jet fuel blendstock candidate. A high-titer 2,3-BDO fermentation broth (i.e., ~90 g/L) was produced at a 100-L scale and pretreated via nanofiltration to decrease the impurities level in the broth from 4.6 to 0.6 wt%. A novel process for catalytic upgrading of aqueous 2,3-BDO into a jet fuel blendstock candidate was developed, and each step was efficiently demonstrated. The catalytic steps include 1) 2,3-BDO dehydration into methyl ethyl ketone (MEK) over AlPO4, 2) MEK conversion into olefins over Zn1Zr10Ox, 3) oligomerization of olefins over a zeolite beta, and 4) hydrogenation over platinum/carbon. Both the model feed and real 2,3-BDO fermentation broth were tested for upgrading 2,3-BDO to MEK. With the real feed, a continuous loss of conversion (i.e., >50% loss over ~140 h time-on-stream [TOS]) was partly attributed to reversible deactivation from coking species. However, the conversion remained stable with the model feed, which demonstrates the efficiency of the first step for converting aqueous 2,3-BDO (10 wt% in water). For upgrading MEK to olefins, high selectivity to olefins (i.e., 82.5%) was obtained at high conversion levels (i.e., 93-98%) with stable conditions being achieved for > 70-hours TOS. Oligomerization of light olefins, which was demonstrated for > 270 h TOS, mainly led to the formation of dimers (C8-10) and trimers (C13-14). The oligomerized product was hydrogenated and distilled to recover the jet fraction (35 mass% or 40.9% carbon based yield), which consists mostly of desired isoalkanes (31.7 wt%), n-alkanes (24.5 wt%), and cycloalkanes (29.6 wt%). While some improvement is still needed to meet ASTM D7566 specifications for viscosity and final boiling point temperature, freezing point, density, aromatics content, and sulfur content of the jet blendstock candidate were within acceptable ranges, thus highlighting the potential of this process for production of jet fuel blendstock.

ADVANCED PROPULSION SYSTEMS,BIOMASS FUELS↗

Bioblendstocks to Optimize Mixing Controlled Compression Ignition (MCCI) Engines

In this project, a team of researchers from the University of Massachusetts Lowell, the University of Maine, and Mainstream Engineering developed an integrated process for the product of bioblendstocks to optimize mixing controlled compression ignition (MCCI) engines. The objective was to improve the energy density, sooting propensity, and cetane number of base diesel fuel while maintaining cold weather behavior. The process converts woody biomass (e.g. sawmill residues) into bio-oil through selective fast pyrolysis; the bio-oil is then selectively upgraded to form selectively oxygenated, minimally-branched hydrocarbons using non-noble metal catalysts in combination with metal-catalyzed hydrogenation. Advanced predictive models, in conjunction with existing property databases, and experimental testing are used to evaluate overall bioblendstock properties and their impact on base diesel fuel. An iterative, targeted upgrading approach was implemented to optimize the proposed bioblendstock’s properties. Assessment methodologies included techno-economic analysis, life-cycle assessment, property testing, and engine testing. Ultimately, the project team successfully produced a viable bioblendstock while identifying critical process points related to scale-up efforts. It was found that producing pyrolysis oils at 500 degrees C and with pine particle sizes of 1-2 mm led to bio-oil with a higher yield (of approximately 45 wt%) and rich amounts of aromatic alcohols. The resultant pyrolysis oil was then upgraded using a sequence of mild hydrotreating, followed by catalytic etherification and esterification, followed by another final mild hydrotreating to produce a blendstock containing saturated species with a limited, but non-zero, amount of oxygen. The aromatic alcohols produced by pyrolysis were especially helpful in this regard, as the resulting bicycloethers and derivatives exhibited high cetane numbers. While most bulk properties of the bioblendstock met or exceeded targeted thresholds, viscosity and cloud point notably fell outside the expected range; this could be addressed by blending limits and/or through the use of additives that are commonplace in current refinding practices. Identification of a bioblendstock that can be produced economically at scale while improving the performance and emissions characteristics of internal combustion engines positively affects the economy by boosting domestic fuel production and the environment by decreasing harmful emissions and increasing efficiency.

09 BIOMASS FUELS↗

A numerically exact full wave packet approach to molecule-surface scattering

A numerically exact spectral method for solving the time-dependent Schroedinger equation in spherical coordinates is described. The angular dependence of the wave function is represented on a two-dimensional grid of evenly spaced points. The fast Fourier transform algorithm is used to transform between the angle space representation of the wave function and its conjugate representation in momentum space. The time propagation of the wave function is evaluated using an expansion of the time evolution operator as a series of Chebyshev polynomials. Calculations performed for a model system representing H2 scattering from a rectangular corrugated surface yield transition probabilities that are in excellent agreement with those obtained using the close-coupling wave packet (CCWP) method. However, the new method is found to require substantially more computation time than the CCWP method because of the large number of grid points needed to represent the angular dependence of the wave function and the variation in the number of terms required in the Chebyshev representation of the time evolution operator.

Mowrey, R. C.↗

Dispersing nano- and micro-sized portlandite particulates via electrosteric exclusion at short screening lengths

In spite of their high surface charge (zeta potential ζ = +34 mV), aqueous suspensions of portlandite (calcium hydroxide: Ca(OH) 2 ) exhibit a strong tendency to aggregate, and thereby present unstable suspensions. While a variety of commercial dispersants seek to modify the suspension stability and rheology (e.g., yield stress, viscosity), it remains unclear how the performance of electrostatically and/or electrosterically based additives is affected in aqueous environments having either a high ionic strength and/or a pH close to the particle's isoelectric point (IEP). We show that the high native ionic strength (pH ≈ 12.6, IEP: pH ≈ 13) of saturated portlandite suspensions strongly screens electrostatic forces (Debye length: κ -1 = 1.2 nm). As a result, coulombic repulsion alone is insufficient to mitigate particle aggregation and affect rheology. However, a longer-range geometrical particle–particle exclusion that arises from electrosteric hindrance caused by the introduction of comb polyelectrolyte dispersants is very effective at altering the rheological properties and fractal structuring of suspensions. As a result, comb-like dispersants that stretch into the solvent reduce the suspension's yield stress by 5× at similar levels of adsorption as compared to linear dispersants, thus enhancing the critical solid loading (i.e., at which jamming occurs) by 1.4×. Significantly, the behavior of diverse dispersants is found to be inherently related to the thickness of the adsorbed polymer layer on particle surfaces. These outcomes inform the design of dispersants for concentrated suspensions that present strong charge screening behavior.

36 MATERIALS SCIENCE↗

Gross-fragmentation of meteoroids and bulk density of Geminids from photographic fireball records

The explicit solution of the drag and ablation equations of a single nonfragmenting meteoroid moving in any actual atmosphere was published several years ago. The solution yields the theoretical relation of l, the distance flown by the meteoroid in its trajectory, as a function of time, t, assuming that the height, h, is a known function of l. The photographic records of meteors and fireballs are coded by time marks, using a rotating shutter or a similar device to break the moving image. Time is, thus, the independent variable and for each time mark on a meteoroid trajector, the observed distance along the trajectory, l sub obs, as well as the double- or multiple- station photographs of the same meteoroid. Applying this solution to all available Prairie Network (PN) fireball-records, we recognized that the majority of them gave good solutions with standard deviations somewhat bigger than the intrinsic geometrical precision of the data. We also noticed that, on an average, previous methods of evaluation of the meteoroid velocities (interpolation polynomials, numerical differenciation of the observed l sub obs) used up to only several tens of percent of the intrinsic precision of the PN observational data. When residuals of these solutions, i.e. l sub obs - l sub com, were represented as a function of time for about 75 percent of solutions. The remaining 25 percent of residuals showed systematic changes with time exceeding one standard deviation. We tried to explain these systematic time course of residuals by using different meteoroids first computed theoretically and then analyzed by the same model as the natural PN fireballs were. The conclusion of these model computations is that systematic time changes of residuals in the nonfragmenting model exceeding one standard of deviation are caused by sudden gross fragmentation at one or more trajectory points. Thus, we generalized the explicit solution of the drag and ablation equations of a single nonfragmenting meteoroid by allowing for one or more points, where sudden gross fragmentation can occur. Using this generalized solution, the distances along the meteoroid trajectory can be computed for any choice of input parameters and compared with the observed distances flown by the meteoroid. For the most precise and long fireball trajectories, the least-squares solution can, thus, yield the initial velocities, the ablation coefficients, the dynamical masses, the positions of gross-fragmentation points, and the terminal mass. At a gross-fragmentation point, the ratio of the main mass to all the remaining fragments can be compared with the dynamic mass determined from our gross-fragmentation model and, thus, the meteoroid bulk density can be evaluated. We applied the gross-fragmentation model to sever PN fireballs showing time changes of residuals, and we recognized that, in all these cases, the new computed bulk densities of meteoroids resulted higher in comparison with the meteoroid densities determined with the non-gross-fragmentation model. Other aspects of the study are discussed.

Ceplecha, Zdenek↗