SEARCH · Engineering Papers

Results for “wake models”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

NASA NTRS1974

Longitudinal aerodynamic characteristics of an externally blown flap powered lift model with several propulsive system simulators

An investigation of a four-engine externally blown flap (EBF) powered-lift transport was conducted in the Langley V/STOL tunnel to determine the effect of different engine configurations on the longitudinal aerodynamic characteristics. The different engine configurations were simulated by five different sets of propulsion simulators on a single aircraft model. Longitudinal aerodynamic data were obtained for each simulator on each flap deflection corresponding to cruise, take-off, and landing at a range of angles of attack and various thrust coefficients. The bypass ratio (BPR) 6.2 engine simulator provided the best lift and drag characteristics of the five simulators tested in the take-off and landing configurations. The poor performance of the BPR 10.0 and 3.2 engine simulators can be attributed to a mismatch of engine-model sizes or poor engine location and orientation. Isolated engine wake surveys indicated that a reasonable assessment of the aerodynamic characteristics of an engine-wing-flap configuration could be made if qualitative information were available which defined the engine wake characteristics. All configurations could be trimmed easily with relatively small horizontal-tail incidence angles; however, the take-off landing configurations required a high-lift tail.

Hoad, D. R.↗

NASA NTRS1976

Time development of the flow about an impulsively started cylinder

A method is developed to determine the time-dependent flowfield about an impulsively started circular cylinder. An outer potential flow model is interfaced with an inner viscous flow region. The wake is described by a set of elementary point vortices. The position at which the point vortices are shed from the cylinder is obtained from a solution to the unsteady incompressible laminar boundary-layer equations. A rear shear-layer is postulated to account for backflow induced vorticity. Wake development is detailed from the initial formation of the two symmetric vortices to subsequent asymmetry and eventual alternate shedding. Unsteady pressure distributions, lift and drag forces, and Strouhal number are calculated and compared with experiment.

Deffenbaugh, F. D.↗

NASA NTRS1981

The influence of unsteady aerodynamics on hingeless rotor ground resonance

Calculations of the model frequency and damping for a hingeless rotor on a gimballed support in hover are compared with measured results for two configurations (differing in blade flap stiffness). Good correlation is obtaned when an inflow dynamics model is used to account for the influence of the unsteady aerodynamics. The effect of the unsteady aerodynamics is significant for this rotor system. The inflow dynamics model introduces additional states corresponding to perturbations of the wake-induced velocity at the rotor disk. The calculations confirm the experimental observation that the inflow mode introduced by these additional states is measurable for one configuration but not for the other.

Johnson, W.↗

NASA NTRS1984

Comparison of experimental and analytical predictions of rotor blade-vortex interactions using model scale acoustic data

Helicopter blade-vortex interaction (BVI) noise is studied using a model scale rotor acoustic data base and an analytical rotor wake prediction method. The variation of BVI acoustic levels with vehicle flight conditions (forward speed and disk attitude) is presented. Calculations of probable BVI locations on the rotor disk are made for a range of operating conditions using the measured acoustic signals and an acoustic ray tracing technique. Analytical predictions of possible BVI locations on the rotor disk are made using a generalized distorted wake analysis program. Comparisons of the interaction locations are made with the results of both the analytic approach and the acoustic ray tracing technique.

Martin, R. M.↗

NASA NTRS1987

Computation of subsonic base flow on a vector processor

Two-dimensional subsonic laminar compressible base flow has been studied using numerical solutions of the time-dependent Navier-Stokes equations. These solutions were obtained using an explicit finite-difference scheme which is highly efficient on a vector processor. The organization of the code for a CDC CYBER-205 computer is described. Solutions were obtained for Mach 0.4 and 0.6 flows past a slender blunt-based model at moderately high Reynolds numbers. The flow in the wake is unsteady with periodic shedding of vortices from the trailing edge. The computed shedding frequency was found to increase with increasing Reynolds number.

Rudy, D. H.↗

NASA NTRS1988

Numerical simulation of a subsonic jet in a crossflow

The aerodynamic/propulsive interaction between a subsonic jet exhausting perpendicularly through a flat plate into a crossflow is investigated numerically using an approximately factored, partially flux-split, implicit solver for the three-dimensional, thin-layer Navier-Stokes equations. This algorithm is applied to flows with a range of jet-to-crossflow velocity ratios between 4 and 8. The computations model the jet trajectory, the contrarotating vortex pair and the wake region near the plate downstream of the jet orifice. Both qualitative and quantitative agreement with the existing experimental database are demonstrated. Flow visualization is instructive for understanding the physics of this flowfield.

Roth, Karlin R.↗

NASA NTRS1992

An experimental study of a turbulent boundary layer in the trailing edge region of a circulation-control airfoil

This report discusses progress made on NASA Cooperative Agreement NCC2-545, 'An Experimental Study of a Turbulent Boundary Layer in the Trailing-Edge Region of a Circulation-Control Airfoil' during the period 9/1/91 through 9/30/92. The study features 2-component laser Doppler velocimeter (LDV) measurements in the trailing edge and wake regions of a generic 2-dimensional circulation-control model. The final experimental phase of the study will be carried out in the Ames High Reynolds Number Channel 2 (HRC2) transonic blow-down-facility. During the 13-month period covered by this report, work continued on the development of the near-wall laser Doppler velocimeter (LDV) described in previous reports.

Heinemann, K.↗

NASA NTRS1994

Prediction of Undsteady Flows in Turbomachinery Using the Linearized Euler Equations on Deforming Grids

A linearized Euler solver for calculating unsteady flows in turbomachinery blade rows due to both incident gusts and blade motion is presented. The model accounts for blade loading, blade geometry, shock motion, and wake motion. Assuming that the unsteadiness in the flow is small relative to the nonlinear mean solution, the unsteady Euler equations can be linearized about the mean flow. This yields a set of linear variable coefficient equations that describe the small amplitude harmonic motion of the fluid. These linear equations are then discretized on a computational grid and solved using standard numerical techniques. For transonic flows, however, one must use a linear discretization which is a conservative linearization of the non-linear discretized Euler equations to ensure that shock impulse loads are accurately captured. Other important features of this analysis include a continuously deforming grid which eliminates extrapolation errors and hence, increases accuracy, and a new numerically exact, nonreflecting far-field boundary condition treatment based on an eigenanalysis of the discretized equations. Computational results are presented which demonstrate the computational accuracy and efficiency of the method and demonstrate the effectiveness of the deforming grid, far-field nonreflecting boundary conditions, and shock capturing techniques. A comparison of the present unsteady flow predictions to other numerical, semi-analytical, and experimental methods shows excellent agreement. In addition, the linearized Euler method presented requires one or two orders-of-magnitude less computational time than traditional time marching techniques making the present method a viable design tool for aeroelastic analyses.

Clark, William S.↗

NASA NTRS1999

Computation of Turbulent Wake Flows in Variable Pressure Gradient

Transport aircraft performance is strongly influenced by the effectiveness of high-lift systems. Developing wakes generated by the airfoil elements are subjected to strong pressure gradients and can thicken very rapidly, limiting maximum lift. This paper focuses on the effects of various pressure gradients on developing symmetric wakes and on the ability of a linear eddy viscosity model and a non-linear explicit algebraic stress model to accurately predict their downstream evolution. In order to reduce the uncertainties arising from numerical issues when assessing the performance of turbulence models, three different numerical codes with the same turbulence models are used. Results are compared to available experimental data to assess the accuracy of the computational results.

Duquesne, N.↗

NASA NTRS2005

Management of Vortices Trailing Flapped Wings via Separation Control

A pilot study was conducted on a flapped semi-span model to investigate the concept and viability of near-wake vortex management via separation control. Passive control was achieved by means of a simple fairing and active control was achieved via zero mass-flux blowing slots. Vortex sheet strength, estimated by integrating surface pressure ports, was used to predict vortex characteristics by means of inviscid rollup relations. Furthermore, vortices trailing the flaps were mapped using a seven-hole probe. Separation control was found to have a marked effect on vortex location, strength, tangential velocity, axial velocity and size over a wide range of angles of attack and control conditions. In general, the vortex trends were well predicted by the inviscid rollup relations. Manipulation of the separated flow near the flap edges exerted significant control over both outboard and inboard edge vortices while producing negligible lift excursions. Dynamic separation and attachment control was found to be an effective means for dynamically perturbing the vortex from arbitrarily long wavelengths down to wavelengths less than a typical wingspan. In summary, separation control has the potential for application to time-independent or time-dependent wake alleviation schemes, where the latter can be deployed to minimize adverse effects on ride-quality and dynamic structural loading.

Greenblatt, David↗

NASA NTRS2006

Managing Flap Vortices via Separation Control

A pilot study was conducted on a flapped semi-span model to investigate the concept and viability of near-wake vortex management by means of boundary layer separation control. Passive control was achieved using a simple fairing and active control was achieved via zero mass-flux blowing slots. Vortex sheet strength, estimated by integrating surface pressures, was used to predict vortex characteristics based on inviscid rollup relations and vortices trailing the flaps were mapped using a seven-hole probe. Separation control was found to have a marked effect on vortex location, strength, tangential velocity, axial velocity and size over a wide range of angles of attack and control conditions. In general, the vortex trends were well predicted by the inviscid rollup relations. Manipulation of the separated flow near the flap edges exerted significant control over either outboard or inboard edge vortices while producing small lift and moment excursions. Unsteady surface pressures indicated that dynamic separation and attachment control can be exploited to perturb vortices at wavelengths shorter than a typical wingspan. In summary, separation control has the potential for application to time-independent or time-dependent wake alleviation schemes, where the latter can be deployed to minimize adverse effects on ride-quality and dynamic structural loading.

Greenblatt, David↗

NASA NTRS2010

Landing Gear Components Noise Study - PIV and Hot-Wire Measurements

PIV and hot-wire measurements of the wake flow from rods and bars are presented. The test models include rods of different diameters and cross sections and a rod juxtaposed to a plate. The latter is representative of the latch door that is attached to an aircraft landing gear when the gear is deployed, while the single and multiple rod configurations tested are representative of some of the various struts and cables configuration present on an aircraft landing gear. The test set up is described and the flow measurements are presented. The effect of model surface treatment and freestream turbulence on the spanwise coherence of the vortex shedding is studied for several rod and bar configurations.

Hutcheson, Florence V.↗

NASA NTRS1979

The development of methods for predicting and measuring distribution patterns of aerial sprays

The capability of conducting scale model experiments which involve the ejection of small particles into the wake of an aircraft close to the ground is developed. A set of relationships used to scale small-sized dispersion studies to full-size results are experimentally verified and, with some qualifications, basic deposition patterns are presented. In the process of validating these scaling laws, the basic experimental techniques used in conducting such studies, both with and without an operational propeller, were developed. The procedures that evolved are outlined. The envelope of test conditions that can be accommodated in the Langley Vortex Research Facility, which were developed theoretically, are verified using a series of vortex trajectory experiments that help to define the limitations due to wall interference effects for models of different sizes.

Ormsbee, A. I.↗

NASA NTRSDate not supplied

Prediction of Broadband Blade-Wake Back-Scatter Noise from a Hovering Ideally Twisted Rotor using OVERFLOW2-ANOPP2

This work illustrates the use of a hybrid RANS/LES framework for the prediction of broadband noise via integral formulations from an ideally twisted hovering rotor. Four simulations were conducted, which investigated the effect of different turbulence modeling and spatiotemporal resolutions. The aerodynamic performance and aeroacoustics predicted by these four computational cases were compared against data acquired in the Small Hover Anechoic Chamber at the NASA Langley Research Center and against previous simulations conducted using the lattice-Boltzmann solver, PowerFLOW. The simulation case with the finest spatial resolution had the most favorable aerodynamic performance and broadband noise comparison with measured data; however, the simulation case utilizing the SST-DDES turbulence model predicted the most accurate tonal noise signature. Aerodynamic flowfield visualizations identified near-wake trailing edge vortex shedding, perpendicular blade-vortex interactions, and tip vortex formation, which are known to cause broadband noise. The fluid dynamics associated with a new broadband noise source, blade-wake back-scatter, were also identified. Lastly, a broadband noise source visualization technique was utilized to confirm the presence of blade-wake back-scatter as a dominant broadband noise source.

blade-wake back-scatter↗

NASA NTRS1995

The effects of vortex modeling on blade-vortex interaction noise prediction

The use of a blade vortex interaction noise prediction scheme, based on CAMRAD/JA, FPR and RAPP, quantifies the effects of errors and assumptions in the modeling of the helicopter's shed vortex on the acoustic predictions. CAMRAD/JA computes the wake geometry and inflow angles that are used in FPR to solve for the aerodynamic surface pressures. RAPP uses these surface pressures to predict the acoustic pressure. Both CAMRAD/JA and FPR utilize the Biot-Savart Law to determine the influence of the vortical velocities on the blade loading and both codes use an algebraic vortex model for the solid body rotation of the vortex core. Large changes in the specification of the vortex core size do not change the inplane wake geometry calculated by CAMRAD/JA and only slightly affect the out-of-plane wake geometry. However, the aerodynamic surface pressure calculated by FPR changes in both magnitude and character with small changes to the core size used by the FPR calculations. This in turn affects the acoustic predictions. Shifting the CAMRAD/JA wake geometry away from the rotor plane by 1/4 chord produces drastic changes in the acoustic predictions indicating that the prediction of acoustic pressure is extremely sensitive to the miss distance between the vortex and the blade and that this distance must be calculated as accurately as possible for acceptable noise predictions. The inclusion or exclusion of a vortex in the FPR-RAPP calculation allows for the determination of the relative importance of that vortex as a BVI noise source.

Gallman, Judith M.↗

NASA NTRS1974

The Vortex Lattice Method for the Rotor-Vortex Interaction Problem

The rotor blade-vortex interaction problem and the resulting impulsive airloads which generate undesirable noise levels are discussed. A numerical lifting surface method to predict unsteady aerodynamic forces induced on a finite aspect ratio rectangular wing by a straight, free vortex placed at an arbitrary angle in a subsonic incompressible free stream is developed first. Using a rigid wake assumption, the wake vortices are assumed to move downsteam with the free steam velocity. Unsteady load distributions are obtained which compare favorably with the results of planar lifting surface theory. The vortex lattice method has been extended to a single bladed rotor operating at high advance ratios and encountering a free vortex from a fixed wing upstream of the rotor. The predicted unsteady load distributions on the model rotor blade are generally in agreement with the experimental results. This method has also been extended to full scale rotor flight cases in which vortex induced loads near the tip of a rotor blade were indicated. In both the model and the full scale rotor blade airload calculations a flat planar wake was assumed which is a good approximation at large advance ratios because the downwash is small in comparison to the free stream at large advance ratios. The large fluctuations in the measured airloads near the tip of the rotor blade on the advance side is predicted closely by the vortex lattice method.

Padakannaya, R.↗

NASA NTRS1973

Experimental investigation of model variable-geometry and ogee tip rotors.

An experimental investigation was conducted to systematically explore the effects of inter-blade spatial relationships and pitch variations on rotor performance and wake geometry. Variable-geometry rotors consisting of various combinations of blade length, axial spacing, azimuth spacing, and collective pitch were tested at model scale in hover and forward flight. In addition, a hover test of a rotor with an ogee blade tip design was conducted to determine its performance and wake characteristics. The results of this investigation indicate that several variable-geometry rotor configurations can offer substantial improvements in hover performance without adversely affecting forward flight performance.

Landgrebe, A. J.↗

NASA NTRS2011

Advection of Microphysical Scalars in Terminal Area Simulation System (TASS)

The Terminal Area Simulation System (TASS) is a large eddy scale atmospheric flow model with extensive turbulence and microphysics packages. It has been applied successfully in the past to a diverse set of problems ranging from prediction of severe convective events (Proctor et al. 2002), tracking storms and for simulating weapons effects such as the dispersion and fallout of fission debris (Bacon and Sarma 1991), etc. More recently, TASS has been used for predicting the transport and decay of wake vortices behind aircraft (Proctor 2009). An essential part of the TASS model is its comprehensive microphysics package, which relies on the accurate computation of microphysical scalar transport. This paper describes an evaluation of the Leonard scheme implemented in the TASS model for transporting microphysical scalars. The scheme is validated against benchmark cases with exact solutions and compared with two other schemes - a Monotone Upstream-centered Scheme for Conservation Laws (MUSCL)-type scheme after van Leer and LeVeque's high-resolution wave propagation method. Finally, a comparison between the schemes is made against an incident of severe tornadic super-cell convection near Del City, Oklahoma.

Ahmad, Nashat N.↗