SEARCH · Engineering Papers

Results for “velocity model evaluation”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

DOE OSTI2022

Impact of particle size and particle-flow-wall coupling on pressurized oxy-combustion in the down-fired burner

Concerns over climate change have led to numerous efforts in developing low-carbon energy technologies. Pressurized oxy-combustion (POC) is a promising candidate to reduce carbon emissions in power generation. Designing an effective burner plays a vital role in developing new coal combustion technologies. Because of the high pressure, the volume fraction of coal particles at the fuel inlet of the burner of a pressurized oxy-combustor is close or even higher than the maximum limit that commercial CFD codes (e.g., ANSYS FLUENT) can handle. At this high particle volume fraction, the interactions among particles, fluid flow, and wall need to be re-evaluated. The present computational work is the first step of a systematic analysis of the particle influence, like releasing method, releasing locating, and particle size, in a pilot-scale POC combustor, developed at Washington University in St. Louis (WUSTL). In a POC process, pulverized coal is burned under elevated pressure and O2-CO2 environment. Specifically, a 15-bar, 100 kWth, POC combustor is modeled employing ANSYS FLUENT, using Reynolds-averaged Navier-Stokes (RANS) modeling. It is revealed that for this pilot-scale, pressurized burner, velocity profiles of the near-wall region in this POC facility exhibit some discrepancy against the near-wall turbulent flow velocity profile. In order to investigate the particle influence in the near-wall region, particle releasing location will be investigated. Numerical simulation results exhibit the coupling effect of turbulence flow and particles in this case. The particle size also demonstrates a great effect on particle trajectory, then further has an impact on flame stability and temperature.

Li, Lei↗

NASA NTRS1976

The ionization of cloud and intercloud hydrogen by O and B stars

The ionization and acceleration of neutral clouds in the neighborhood of a single O star located in a low-density intercloud medium (ICM) are analyzed. It is shown that due to ionized cloud debris, the rms electron density may increase to 1 per cu cm in the lifetime of the star. It is suggested that an O star which moves away from its primordial nebula at a velocity of 10 to 20 km/s may continuously surround itself with ionized cloud debris and may never extensively ionize a low-density ICM. The lifetime of a remote cloud exposed to relatively uniform Lyman continuum radiation is derived and evaluated as a function of position in the Galaxy. It is found that extensive O-star ionization of a low-density ICM cannot be maintained for more than a few million years if the cloud debris is not cleared away by, for example, supernovae. Various ICM models are examined in which B stars and possibly nuclei of planetary nebulae play a major role in the ionization of interstellar hydrogen. It is shown that such stars may ionize a larger volume of the Galaxy than O stars, even though the volume emissivity of their Lyman continuum radiation is only 5% to 15% of that of O stars.

Elmergreen, B. G.↗

NASA NTRS1981

A model for the acoustic impedance of linear suppressor materials bonded on perforated plate

An analytical model is developed for the acoustic impedance of a composite made of a fine screen bonded to a perforated plate, the resistance having been modeled using steady flow theory and data, and including both linear and nonlinear components. The model of the screen resistance alone is derived first, and it is then extended to include a perforated plate bonded to the screen. Quantities such as effective open ratio and pressure recovery are evaluated. Conclusions are presented, including: (1) when the screen is bonded to a perforated plate, the linear resistance increases as the inverse of the perforate open area, (2) the nonlinearity in the screen resistance depends on the square of the screen wire diameter, and (3) when the resistance is considered as a function of approach velocity, the screen nonlinear term increases as the inverse of the square of the perforated plate open area ratio. The general theory can be applied to any screen structure, but final results are limited to a twilled square weave screen. Results can be applied to the study of sound absorbing materials used for lining the walls of aircraft engine duct suppressors.

Rice, E. J.↗

NASA NTRS1995

The second-moment climatology of the GATE rain rate data

The first part of this paper presents the description of the GARP (Global Atmospheric Research Program) Atlantic Tropical Experiment (GATE) 1 rain-rate data and its two-dimensional spectral and correlation characteristics, which has made it possible to accomplish the following: to show the concentration of a significant power along the frequency axis in the spatiotemporal spectra; to detect a diurnal cycle (which has a range of variation of about 3.4-5.4 mm/n) as one of the sources of bias in the rain statistics of satellite data; to study the distinction between the north-south and east-west transport of spatial rain-rate field and character of its anisotropy; to evaluate the scales of the distinction between second-moment estimates associated with ground and satellite samples; and to determine the appropriate spatial and temporal scales of simple linear stochastic models fitted to averaged rain-rate fields. The second part of this paper is devoted to an analysis of the diffusion of the rain rate by establishing a relationship between the parameters of the multivariate autoregressive model and the coefficients of a diffusion equation. This analysis led to the use of rain data to estimate the rain advection velocity as well as other coefficients of the diffusion equation of the corresponding field. The results obtained can be used for comparison with corresponding estimates of other sources of data (satellite, Tropical Oceans Global Atmosphere Coupled Ocean - Atmosphere Response Experiment (TOGA, COARE) or simulated by physical models), for generating multiple samples of any size, for solving the inverse problems of some of the hydrodynamic equations, and in some other areas of rain data analysis and modeling.

Polyak, Ilya↗

NASA NTRS2008

CFD Modeling of Superheated Fuel Sprays

An understanding of fuel atomization and vaporization behavior at superheat conditions is identified to be a topic of importance in the design of modern supersonic engines. As a part of the NASA aeronautics initiative, we have undertaken an assessment study to establish baseline accuracy of existing CFD models used in the evaluation of a ashing jet. In a first attempt towards attaining this goal, we have incorporated an existing superheat vaporization model into our spray solution procedure but made some improvements to combine the existing models valid at superheated conditions with the models valid at stable (non-superheat) evaporating conditions. Also, the paper reports some validation results based on the experimental data obtained from the literature for a superheated spray generated by the sudden release of pressurized R134A from a cylindrical nozzle. The predicted profiles for both gas and droplet velocities show a reasonable agreement with the measured data and exhibit a self-similar pattern similar to the correlation reported in the literature. Because of the uncertainty involved in the specification of the initial conditions, we have investigated the effect of initial droplet size distribution on the validation results. The predicted results were found to be sensitive to the initial conditions used for the droplet size specification. However, it was shown that decent droplet size comparisons could be achieved with properly selected initial conditions, For the case considered, it is reasonable to assume that the present vaporization models are capable of providing a reasonable qualitative description for the two-phase jet characteristics generated by a ashing jet. However, there remains some uncertainty with regard to the specification of certain initial spray conditions and there is a need for experimental data on separate gas and liquid temperatures in order to validate the vaporization models based on the Adachi correlation for a liquid involving R134A.

Raju, M. S.↗

NASA NTRS2018

Mars Optimal Aerobrake Maneuver Estimation

Mars science satellites often perform orbit changes to obtain different measurements, ground tracks or relay operations. Large reductions in semi-major axis and eccentricity can be done efficiently using the atmospheric drag, a.k.a aerobrake. Aerobraking is one of the most challenging planetary orbit maneuvers in terms of planning and operations. The most important consideration for aerobraking is maintaining the spacecraft's periapsis within an allocated atmospheric density corridor, which is accomplished by raising or lowering periapsis through one or a series of very small and short maneuvers. These maneuvers must be performed as efficiently as possible due to propellant constraints. Work herein details a fast and accurate method to calculate the required impulsive velocity changes in the orbit to guarantee that the spacecraft remains in a prescribed density corridor. The method makes use of the orbit's state transition matrix to map the solution space around the reference orbit. It evaluates the most efficient maneuver epochs to target a given periapsis change with a linear optimal control for single or multiple maneuvers. A fast calculation of the maneuver allows for a more comprehensive evaluation of the trade space, and the selected maneuver may be re-targeted later with a higher- fidelity model. Comparisons against fully propagated models and direct method optimizations demonstrate the new method's performance.

Sarli, Bruno V.↗

NASA NTRS1989

Monte-Carlo modeling of polar wind photoelectron distributions with anomalous heat flux

In situ measurements above the polar cap by the DE satellites show asymmetric field-aligned electron velocity distributions in the photoelectron energy range 5-60 eV. The formation of these anisotropic distributions is described by a collisional kinetic equation that includes the effects of Coulomb collisions (via a Fokker-Planck operator), those of a parallel electric field, and the magnetic mirror effects of the geomagnetic field. This equation is solved using a Monte Carlo simulation method. The simulation illustrates the formation of the portion of the observed electron distributions originating in the ionosphere and makes it possible to evaluate the significance of the suprathermal electrons at higher altitude. Both observations and calculations indicate that these electrons possess an energy flux which, by its effect on the polar-wind electric field, may influence the dynamics of the polar-wind outflow.

Yasseen, F.↗

NASA NTRS1973

Evaluation of experimental flow properties in the wake of a Viking '75 entry vehicle.

An experimental investigation has been conducted to obtain the flow properties in the wake of a model of the Viking '75 entry vehicle. Data are presented for the model at several angles of attack at free-stream Mach numbers from 0.2 to 3.95. The characteristics of the wake flow field are discussed and results are shown to demonstrate the significant variation of wake center-line flow properties in the transonic speed range, the shift in wake profiles with change in angle of attack, and the similarity exhibited by the velocity profiles across the wake.

Campbell, J. F.↗

NASA NTRS1985

Measurements in the flow field of a cylinder with a laser transit anemometer and a drag rake in the Langley 0.3 m transonic cryogenic tunnel

An experiment was conducted at the 0.3 m Transonic Cryogenic Tunnel using a Laser Transit Anemometer (LTA) to probe the flow field around a 3.05 centimeter-diameter circular cylinder. Measurements were made along the stagnation line and determination of particle size was evaluated by their ability to follow the flow field. The LTA system was also used to scan into the boundary layer near the 45 degree point on the model. Results of these scans are presented in graphic and tabular form. Flow field particle seeding was accomplished by inbleeding dry service air. The residual moisture (5-10 ppm) condensed and formed ice particles which served as Mie scattering centers for the LTA detection system. Comparison of data taken along the stagnation streamline with theory indicated that these particles tracked the velocity gradient of the flow. Tunnel operating conditions for the tests were a Mach number of 0.3, a pressure of 1.93 x 100000 n/m squared, and a temperature of 225 degrees K. Free stream Mach number and pressure were varied for the particle size determination.

Honaker, W. C.↗

NASA NTRS1986

Designing Delta-DOR acquisition strategies to determine highly elliptical earth orbits

Delta-DOR acquisition strategies are designed for use in determining highly elliptical earth orbits. The requirements for a possible flight demonstration are evaluated for the Charged Composition Explorer spacecraft of the Active Magnetospheric Particle Tracer Explorers. The best-performing strategy uses data spanning the view periods of two orthogonal baselines near the same orbit periapse. The rapidly changing viewing geometry yields both angular position and velocity information, but each observation may require a different reference quasar. The Delta-DOR data noise is highly dependent on acquisition geometry, varying several orders of magnitude across the baseline view periods. Strategies are selected to minimize the measurement noise predicted by a theoretical model. Although the CCE transponder is limited by S-band and a small bandwidth, the addition of Delta-DOR to coherent Doppler and range improves the one-sigma apogee position accuracy by more than an order of magnitude. Additional Delta-DOR accuracy improvements possible using dual-frequency (S/X) calibration, increased spanned bandwidth, and water-vapor radiometry are presented for comparison. With these benefits, the residual Delta-DOR data noise is primarily due to quasar position uncertainties.

Frauenholz, R. B.↗

NASA NTRS1986

Evaluation of total energy-rate feedback for glidescope tracking in wind shear

Low-altitude wind shear is recognized as an infrequent but significant hazard to all aircraft during take-off and landing. A total energy-rate sensor, which is potentially applicable to this problem, has been developed for measuring specific total energy-rate of an airplane with respect to the air mass. This paper presents control system designs, with and without energy-rate feedback, for the approach to landing of a transport airplane through severe wind shear and gusts to evaluate application of this sensor. A system model is developed which incorporates wind shear dynamics equations with the airplance equations of motion, thus allowing the control systems to be analyzed under various wind shears. The control systems are designed using optimal output feedback and are analyzed using frequency domain control theory techniques. Control system performance is evaluated using a complete nonlinear simulation of the airplane and a severe wind shear and gust data package. The analysis and simulation results indicate very similar stability and performance characteristics for the two designs. An implementation technique for distributing the velocity gains between airspeed and ground speed in the simulation is also presented, and this technique is shown to improve the performance characteristics of both designs.

Belcastro, C. M.↗

NASA NTRS1990

Physical interpretation and application of principles of ultrasonic nondestructive evaluation of high-performance materials

An ultrasonic measurement system employed in the experimental interrogation of the anisotropic properties (through the measurement of the elastic stiffness constants) of the uniaxial graphite-epoxy composites is presented. The continuing effort for the development of improved visualization techniques for physical parameters is discussed. The background is set for the understanding and visualization of the relationship between the phase and energy/group velocity for propagation in high-performance anisotropic materials by investigating the general requirements imposed by the classical wave equation. The consequences are considered when the physical parameters of the anisotropic material are inserted into the classical wave equation by a linear elastic model. The relationship is described between the phase velocity and the energy/group velocity three dimensional surfaces through graphical techniques.

Miller, James G.↗

NASA NTRS1990

Aerodynamics support of research instrument development

A new velocimetry system is currently being developed at NASA LaRC. The device, known as a Doppler global velocimeter (DGV), can record three velocity components within a plane simultaneously and in near real time. To make measurements the DGV, like many other velocimetry systems, relies on the scattering of light from numerous small particles in a flow field. The particles or seeds are illuminated by a sheet of laser light and viewed by two CCD cameras. The scattered light from the particles will have a frequency which is a function of the source laser light frequency, the viewing angle, and most importantly the seed velocities. By determining the scattered light intensity the velocity can be measured at all points within the light sheet simultaneously. Upon completion of DGV component construction and initial check out a series of tests in the Basic Aerodynamic Research (wind) Tunnel (BART) are scheduled to verify instrument operation and accuracy. If the results are satisfactory, application of the DGV to flight measurements on the F-18 High Alpha Research Vehicle (HARV) are planned. The DGV verification test in the BART facility will utilize a 75 degree swept delta wing model. A major task undertaken this summer included evaluation of previous results for this model. A specific series of tests matching exactly the previous tests and exploring new DGV capabilities were developed and suggested. Another task undertaken was to study DGV system installation possibilities in the F-18 HARV aircraft. In addition, a simple seeding system modification was developed and utilized to make Particle Imaging Velocimetry (PIV) measurements in the BART facility.

Miller, L. Scott↗

NASA NTRS1993

The effect of Reynolds number and turbulence on airfoil aerodynamics at -90 degrees incidence

A method has been developed for calculating the viscous flow about airfoils in with and without deflected flaps at -90 deg incidence. This method provides for the solution of the unsteady incompressible Navier-Stokes equations by means of an implicit technique. The solution is calculated on a body-fitted computational mesh using a staggered grid method. The vorticity is defined at the node points, and the velocity components are defined at the mesh-cell sides. The staggered-grid orientation provides for accurate representation of vorticity at the node points and the continuity equation at the mesh-cell centers. The method provides for the direct solution of the flow field and satisfies the continuity equation to machine zero at each time-step. The method is evaluated in terms of its ability to predict two-dimensional flow about an airfoil at -90 degrees incidence for varying Reynolds number and different boundary layer models. A laminar and a turbulent boundary layer models. A laminar and a turbulent boundary layer model are considered in the evaluation of the method. The variation of the average loading and surface pressure distribution due to flap deflection, Reynolds number, and laminar or turbulent flow are presented and compared with experimental results. The comparisons indicate that the calculated drag and drag reduction caused by flap deflection and the calculated average surface pressure are in excellent agreement with the measured results at a similar Reynolds number.

Stremel, Paul M.↗

NASA NTRS1993

Phase 2: HGM air flow tests in support of HEX vane investigation

Following the start of SSME certification testing for the Pratt and Whitney Alternate Turbopump Development (ATD) High Pressure Oxidizer Turbopump (HPOTP), cracking of the leading edge of the inner HEX vane was experienced. The HEX vane, at the inlet of the oxidizer bowl in the Hot Gas Manifold (HGM), accepts the HPOTP turbine discharge flow and turns it toward the Gaseous Oxidizer Heat Exchanger (GOX HEX) coil. The cracking consistently initiated over a specific circumferential region of the hex vane, with other circumferential locations appearing with increased run time. Since cracking had not to date been seen with the baseline HPOTP, a fluid-structural interaction involving the ATD HPOTP turbine exit flowfield and the HEX inner vane was suspected. As part of NASA contract NAS8-36801, Pratt and Whitney conducted air flow tests of the ATD HPOTP turbine turnaround duct flowpath in the MSFC Phase 2 HGM air flow model. These tests included HEX vane strain gages and additional fluctuating pressure gages in the turnaround duct and HEX vane flowpath area. Three-dimensional flow probe measurements at two stations downstream of the turbine simulator exit plane were also made. Modifications to the HPOTP turbine simulator investigated the effects on turbine exit flow profile and velocity components, with the objective of reproducing flow conditions calculated for the actual ATD HPOTP hardware. Testing was done at the MSFC SSME Dynamic Fluid Air Flow (Dual-Leg) Facility, at air supply pressures between 50 and 250 psia. Combinations of turbine exit Mach number and pressure level were run to investigate the effect of flow regime. Information presented includes: (1) Descriptions of turbine simulator modifications to produce the desired flow environment; (2) Types and locations for instrumentation added to the flow model for improved diagnostic capability; (3) Evaluation of the effect of changes to the turbine simulator flowpath on the turbine exit flow environment; and (4) Comparison of the experimental turbine exit flow environment to the environment calculated for the ATD HPOTP.

Cox, G. B., Jr.↗

NASA NTRS2011

Development of Jet Noise Power Spectral Laws

High-quality jet noise spectral data measured at the Aero-Acoustic Propulsion Laboratory (AAPL) at NASA Glenn is used to develop jet noise scaling laws. A FORTRAN algorithm was written that provides detailed spectral prediction of component jet noise at user-specified conditions. The model generates quick estimates of the jet mixing noise and the broadband shock-associated noise (BBSN) in single-stream, axis-symmetric jets within a wide range of nozzle operating conditions. Shock noise is emitted when supersonic jets exit a nozzle at imperfectly expanded conditions. A successful scaling of the BBSN allows for this noise component to be predicted in both convergent and convergent-divergent nozzles. Configurations considered in this study consisted of convergent and convergent- divergent nozzles. Velocity exponents for the jet mixing noise were evaluated as a function of observer angle and jet temperature. Similar intensity laws were developed for the broadband shock-associated noise in supersonic jets. A computer program called sJet was developed that provides a quick estimate of component noise in single-stream jets at a wide range of operating conditions. A number of features have been incorporated into the data bank and subsequent scaling in order to improve jet noise predictions. Measurements have been converted to a lossless format. Set points have been carefully selected to minimize the instability-related noise at small aft angles. Regression parameters have been scrutinized for error bounds at each angle. Screech-related amplification noise has been kept to a minimum to ensure that the velocity exponents for the jet mixing noise remain free of amplifications. A shock-noise-intensity scaling has been developed independent of the nozzle design point. The computer program provides detailed narrow-band spectral predictions for component noise (mixing noise and shock associated noise), as well as the total noise. Although the methodology is confined to single streams, efforts are underway to generate a data bank and algorithm applicable to dual-stream jets. Shock-associated noise in high-powered jets such as military aircraft can benefit from these predictions.

Khavaran, Abbas↗

NASA NTRS1982

Evaluation of a trajectory command concept for manual control of carrier approaches and landings

A novel trajectory control system concept was implemented to provide manual control of a conventional jet aircraft. This concept, called Total Aircraft Flight Control System (TAFCOS), utilizes an inverse model of the aerodynamic and propulsion characteristics and employs feedforward control to provide the required acceleration command. The concept requires on-board digital computations which can easily be handled by a modern airborne computer. The system was studied in a piloted simulation of the carrier approach and landing task with primarily visual flight and guidance cues. The principal modes of vertical flight-path control investigated were vertical velocity command and vertical acceleration command. The study included manual carrier approaches with and without moderate ship motion and associated air disturbances, and tests of the effects of discrete gusts. Manual control of flight path through this new concept was shown to be feasible as an addition to an automatic control system and to have potential as an improved mode of control over conventional control for the carrier approach task.

Mcneill, W. E.↗

DOE OSTI2021

Evaluation of pressure reconstruction techniques for Model Order Reduction in incompressible convective heat transfer

This paper compares pressure reconstruction strategies in Model Order Reduction for incompressible flows with convective heat transfer. The Navier-Stokes equation are reduced along with the passive scalar transport equation for the temperature using the POD-Galerkin technique. Six different pressure reconstruction methods are evaluated, two of which are novel to the best of the authors’ knowledge. Accurate pressure reconstruction is key to avoid error buildup in when solving for the conservation of linear momentum at the reduced level. The six approaches are compared using Direct Numerical Simulations of convective heat exchange processes in a 3D Backward Facing Step with a heated cylinder. Additionally, when comparing time-averaged metrics, we observe that the reconstruction methods that approximate the reduced pressure field using techniques borrowed from full order models (mechanical analogy, pressure Poisson, and velocity supremizers) yield higher errors than the methods that seek to stabilize the reduced systems (reduced residual stabilization, artificial divergence, and Uzawa operator).

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗