Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “small wind”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS2000

Examination of the Lateral Attenuation of Aircraft Noise

Measurements of the lateral attenuation of noise from aircraft operations at Denver International Airport were made at distances up to 2000 feet and elevation angles up to 27 degrees. Attenuation Calculated from modem ground impedance theory agrees well with average measured attenuation. The large variability between measured and predicted levels observed at small elevation angles is demonstrated to be due to refraction by wind and temperature gradients.

Plotkin, Kenneth J.↗
NASA NTRS1941

The Development of a New Lateral-Control Arrangement

Development work on an arrangement using ailerons and spoilers for lateral control was carried out by the Vought-Sikorsky Aircraft Division of the United Aircraft Corporation on a small commercial airplane in flight and on an airfoil in a wind tunnel. Spoiler hinge moments were reduced by aerodynamic balance. The arrangement was then built into an experimental airplane and further improvements were adopted as the result of flight and tunnel tests. The use of ailerons for lateral control with flaps up, spoilers with flaps full down, and gradual transition as the flaps are lowered was found to provide lateral control under the flight conditions for which they were best suited. The ailerons were of short span, permitting the use of long-span flaps, and were drooped to a relatively large angle when the flaps were deflected. A high maximum lift coefficient was thus attained. With large control deflections in the intermediate flap-angle range and spoiler effectiveness near neutral improved by "ventilating" the spoiler, the lateral control was satisfactory for the experimental airplane and was a definite improvement over that of a conventional control arrangement.

Baker, Paul S.↗
NASA NTRS2018

An OSSE Investigating a Constellation of 4-5 Micrometer Infrared Sounders

NASA is investigating the utility of a strategically-constructed constellation of infrared sounders on board small satellites to be able to ultimately provide spaceborne measurements of wind. The method proposed by instrument teams is to fly multiple instruments in complementary orbits so that atmospheric motion vector measurements can be made. As part of the investigation of this measurement approach, the Global Modeling and Assimilation Office (GMAO) at NASA Goddard Space Flight Center performed a set of Observing System Simulation Experiments (OSSEs) to demonstrate the value of the wind measurements as well as the corresponding infrared radiance observations that will come from the constellation. This work was an extension of the GMAO OSSE infrastructure and is in the context of the MISTIC Winds concept. It is noted, though, that this provided insight to the overall measurement strategy. This talk addresses the simulation of the atmospheric motion vectors retrieved via the constellation, the simulation and validation of the radiance observations measured via the constellation, the specification of observations errors for both winds and radiances, and the extension of the data assimilation system to utilize these additional observations on top of a full global observation system. Finally, the results from a set of OSSE experiments is presented.

McCarty, Will↗
NASA NTRS2022

Identification and Reduction of Interactional Noise of a Quadcopter in Hover and Forward Flight Conditions

Advanced Air Mobility is a vision for a safe, accessible, and sustainable aviation system to transport people and cargo between places not served by traditional aviation. With this emerging transportation industry, there is motivation to characterize the noise of vehicles to determine their potential impacts on the community. An experimental testing campaign was conducted on a representative model of a small unmanned aircraft system in the NASA Langley Low Speed Aeroacoustic Wind Tunnel as a continuation of a previous testing campaign. The goals of the current test are to identify sources of interactional noise as well as to test custom-designed rotors and noise reduction devices. The tested noise reduction methods involve increasing the vertical distances between the rotors and the vehicle airframe as well as between the forward and aft rotor disk planes. These methods are intended to reduce rotor-airframe interaction noise in hover and fore-aft rotor wake ingestion noise in forward flight. A phased microphone array is also utilized to identify the locations of prominent noise generation for the different vehicle configurations in forward flight. Elevation of the rotors from the vehicle airframe yielded nearly 8 dBA overall noise reduction in forward flight, while yielding up to 4 dB reduction in overall tonal levels for one of the rotors in hover.

Nikolas S Zawodny↗
NASA NTRS2004

Position Sensor Integral with a Linear Actuator

A noncontact position sensor has been designed for use with a specific two-dimensional linear electromagnetic actuator. To minimize the bulk and weight added by the sensor, the sensor has been made an integral part of the actuator: that is to say, parts of the actuator structure and circuitry are used for sensing as well as for varying position. The actuator (see Figure 1) includes a C-shaped permanent magnet and an armature that is approximately centered in the magnet gap. The intended function of the actuator is to cause the permanent magnet to translate to, and/or remain at, commanded x and y coordinates, relative to the armature. In addition, some incidental relative motion along the z axis is tolerated but not controlled. The sensor is required to measure the x and y displacements from a nominal central position and to be relatively insensitive to z displacement. The armature contains two sets of electromagnet windings oriented perpendicularly to each other and electrically excited in such a manner as to generate forces in the x,y plane to produce the required motion. Small sensor excitation coils are mounted on the pole tips of the permanent magnet. These coils are excited with a sine wave at a frequency of 20 kHz. This excitation is transformer-coupled to the armature windings. The geometric arrangement of the excitation coils and armature windings is such that the amplitudes of the 20-kHz voltages induced in the armature windings vary nearly linearly with x and y displacements and do not vary significantly with small z displacements. Because the frequency of 20 kHz is much greater than the maximum frequency characteristic of the actuation signals applied to the armature windings, there is no appreciable interference between actuator and sensor functions of the armature windings.

Howard, David E.↗
NASA NTRSDate not supplied

Developing Materials and Coating Technologies for Mitigation of Lunar Dust Adhesion and Abrasion

Lunar regolith was first identified as a major issue during the Apollo missions. There are three characteristics of lunar regolith that cause issues: small size, rough surface topology, and particle charge. The lack of a magnetosphere allows solar wind to bombard the lunar surface which results in the regolith becoming charged. These charged particles will adhere to most surfaces and degrade thermal control systems. The lack of atmosphere and surface liquids on the lunar surface results in the regolith’s small particle size, abrasive topology, and chemical reactivity. When the dust adheres to a surface, or the lunar lander exhaust kicks up dust regolith, it can impair instrument or thermal control system function, abrade optical surfaces, diminish range of motion, and mechanically degrade soft-goods such as gloves and astronaut suits. All of these examples were experienced during the Apollo missions. The objective of this study was to select and evaluate abrasion-resistant ceramic materials for application on the lunar landing equipment.

materials↗
NASA NTRS2022

The Imprint of Intermittent Interchange Reconnection on the Solar Wind

The solar wind is known to be highly structured in space and time. Observations from Parker Solar Probe have revealed an abundance of so-called magnetic switchbacks within the near-Sun solar wind. In this Letter, we use a high-resolution, adaptive-mesh, magnetohydrodynamics simulation to explore the disturbances launched into the solar wind by intermittent/bursty interchange reconnection and how they may be related to magnetic switchbacks. We find that repeated ejection of plasmoid flux ropes into the solar wind produces a curtain of propagating and interacting torsional Alfvénic waves. We demonstrate that this curtain forms when plasmoid flux ropes dynamically realign with the radial field as they are ejected from the current layer and that this is a robust effect of the 3D geometry of the interchange reconnection region. Simulated flythroughs of this curtain in the low corona reveal an Alfvénic patch that closely resembles observations of switchback patches, but with relatively small magnetic field deflections. Therefore, we suggest that switchbacks could be the solar wind imprint of intermittent interchange reconnection in the corona, provided an in situ process subsequently amplifies the disturbances to generate the large deflections or reversals of radial field that are typically observed. That is to say, our results indicate that a combination of low-coronal and inner-heliospheric mechanisms may be required to explain switchback observations.

corona↗
NASA NTRS2016

WindBots: A Concept for Persistent In-Situ Science Explorers for Gas Giants

This report summarizes the study of a mission concept to Jupiter with one or multiple Wind Robots able to operate in the Jovian atmosphere, above and below the clouds - down to 10 bar, for long durations and using energy obtained from local sources. This concept would be a step towards persistent exploration of gas giants by robots performing in-situ atmospheric science, powered by locally harvested energy. The Wind Robots, referred in this report as WindBots (WBs), would ride the planetary winds and transform aeolian energy into kinetic energy of flight, and electrical energy for on-board equipment. Small shape adjustments modify the aerodynamic characteristics of their surfaces, allowing for changes in direction and a high movement autonomy. Specifically, we sought solutions to increase survivability to strong/turbulent winds, and mobility and autonomy compared to passive balloons.

WindBots↗
NASA NTRS1992

Analysis of TIMS performance subjected to simulated wind blast

The results of the performance of the Thermal Infrared Multispectral Scanner (TIMS) when it is subjected to various wind conditions in the laboratory are described. Various wind conditions were simulated using a 24 inch fan or combinations of air jet streams blowing toward either or both of the blackbody surfaces. The fan was used to simulate a large volume of air flow at moderate speeds (up to 30 mph). The small diameter air jets were used to probe TIMS system response in reaction to localized wind perturbations. The maximum nozzle speed of the air jet was 60 mph. A range of wind directions and speeds were set up in the laboratory during the test. The majority of the wind tests were conducted under ambient conditions with the room temperature fluctuating no more than 2 C. The temperature of the high speed air jet was determined to be within 1 C of the room temperature. TIMS response was recorded on analog tape. Additional thermistor readouts of the blackbody temperatures and thermocouple readout of the ambient temperature were recorded manually to be compared with the housekeeping data recorded on the tape. Additional tests were conducted under conditions of elevated and cooled room temperatures. The room temperature was varied between 19.5 to 25.5 C in these tests. The calibration parameters needed for quantitative analysis of TIMS data were first plotted on a scanline-by-scanline basis. These parameters are the low and high blackbody temperature readings as recorded by the TIMS and their corresponding digitized count values. Using these values, the system transfer equations were calculated. This equation allows us to compute the flux for any video count by computing the slope and intercept of the straight line that relates the flux to the digital count. The actual video of the target (the lab floor in this case) was then compared with a simulated target. This simulated target was assumed to be a blackbody at emissivity of .95 degrees and the temperature was assumed to be at ambient temperature as recorded by the TIMS for each scanline. Using the slope and the intercept the flux corresponding to this target was converted into digital counts. The counts were observed to have a strong correlation with the actual video as recorded by the TIMS. The attached graphs describe the performance of the TIMS when compressed air is blown at each one of the blackbodies at different speeds. The effect of blowing a fan and changing the room temperature is also being analyzed. Results indicate that the TIMS system responds to variation in wind speed in real time and maintains the capability to produce accurate temperatures on a scan line basis.

Jaggi, S.↗
NASA NTRS1976

A design approach and selected wind tunnel results at high subsonic speeds for wing-tip mounted winglets

Winglets, which are small, nearly vertical, winglike surfaces, substantially reduce drag coefficients at lifting conditions. The primary winglet surfaces are rearward above the wing tips; secondary surfaces are forward below the wing tips. This report presents a discussion of the considerations involved in the design of the winglets; measured effects of these surfaces on the aerodynamic forces, moments, and loads for a representative first generation, narrow body jet transport wing; and a comparison of these effects with those for a wing tip extension which results in approximately the same increase in bending moment at the wing-fuselage juncture as did the addition of the winglets.

Whitcomb, R. T.↗
NASA NTRS2004

Evaluation of High-Resolution Ocean Surface Vector Winds Measured by QuikSCAT Scatterometer in Coastal Regions

The SeaWinds scatterometer onboard QuikSCAT covers approximately 90% of the global ocean under clear and cloudy condition in 24 h, and the standard data product has 25-km spatial resolution. Such spatial resolution is not sufficient to resolve small-scale processes, especially in coastal oceans. Based on range-compressed normalized backscatter and a modified wind retrieval algorithm, a coastal wind dataset at 12.5-km resolution was produced. Even with larger error, the high-resolution winds, in medium to high strength, would still be useful over coastal ocean. Using measurements from moored buoys from the National Buoy Data Center, the high-resolution QuikSCAT wind data are found to have similar accuracy as standard data in the open ocean. The accuracy of both high- and standard-resolution winds, particularly in wind directions, is found to degrade near shore. The increase in error is likely caused by the inadequacy of the geophysical model function/ambiguity removal scheme in addressing coastal conditions and light winds situations. The modified algorithm helps to bring the directional accuracy of the high-resolution winds to the accuracy of the standard-resolution winds in near-shore regions, particularly in the nadir and far zones across the satellite track.

scatterometer↗
NASA NTRS2020

Formation and Topology of Foreshock Bubbles

We use global and local hybrid (kinetic ions and fluid electrons) simulations to investigate the conditions under which foreshock bubbles (FBs) form and how their topology changes with solar wind conditions. FBs form as a result of the interaction between solar wind discontinuities and backstreaming ion beams in the foreshock. They consist of an outer shock and its associated sheath plasma and a low density high temperature core with low magnetic field strength. The structure of FBs is determined by the angle between the interplanetary magnetic field and the normal to the solar wind discontinuity. We show that interaction of rotational discontinuities with the foreshock during small angles between the interplanetary magnetic field and discontinuity normal results in the formation of a nearly spherical bubble with a radius that scales with the width of the foreshock. As this angle increases, FBs become more elongated and eventually become nearly planar structures with dimensions that scale with the length of the foreshock. Despite this transformation, the signatures of FBs in spacecraft time series data remain the same in agreement with the observations. Global simulation results show that FBs form when the solar wind flow speed corresponds to high or intermediate Alfvén Mach numbers (approximately >7 MA). In general, this is tied to the relative speed between the solar wind and ion beams and drop in density of the back streaming ions.

Nick Omidi↗
NASA NTRS1997

Optimal Configuration of an Array of Tabs for Mixing Enhancement in a Shear Layer

The large and small scale vortical motions produced by delta tabs in a two-stream shear layer have been studied experimentally. The tabs were placed at the trailing edge of a splitter plate, mounted in the test section of a wind tunnel, that produced the shear layer. Hot-wire measurements detailed the velocity, vorticity and small scale population distributions in the 3-D space behind the tabs. Small scale structures, which represent the peak in the dissipation spectrum, were identified and counted using the Peak-Valley-Counting technique. The optimal tab inclination angle, theta, and the optimal spanwise spacing, S, for a multiple tab array were identified. The optimal condition was that which maximized the small scale population and generated the strongest streamwise vorticity. Increasing the tab pitch angle from flush to normal to the splitter plate increased the streamwise vorticity as well as the overall small scale population. In fact, the increase in the overall small scale population correlated strongly with the increase in streamwise vorticity intensity. The optimal conditions for peak streamwise vorticity and peak small scale population, with minimum area blockage, were determined to be theta = 45deg and S = 1.5 tab widths.

Foss, J. K.↗
NASA NTRS2004

The Opportunity Rover's Athena science investigation at Meridiani Planum, Mars

The Mars Exploration Rover Opportunity has investigated the landing site in Eagle crater and the nearby plains within Meridiani Planum. The soils consist of fine-grained basaltic sand and a surface lag of hematite-rich spherules, spherule fragments, and other granules. Wind ripples are common. Underlying the thin soil layer, and exposed within small impact craters and troughs, are flat-lying sedimentary rocks. These rocks are finely laminated, are rich in sulfur, and contain abundant sulfate salts. Small-scale cross-lamination in some locations provides evidence for deposition in flowing liquid water. We interpret the rocks to be a mixture of chemical and siliciclastic sediments formed by episodic inundation by shallow surface water, followed by evaporation, exposure, and desiccation. Hematite-rich spherules are embedded in the rock and eroding from them. We interpret these spherules to be concretions formed by postdepositional diagenesis, again involving liquid water.

Mars↗
NASA NTRS1988

Hot gas ingestion testing of an advanced STOVL concept in the NASA Lewis 9- by 15-foot low speed wind tunnel with flow visualization

Advanced Short Takeoff/Vertical Landing (STOVL) aircraft capable of operating from remote sites, damaged runways, and small air capable ships are being pursued for deployment around the turn of the century. To achieve this goal, it is important that the technologies critical to this unique class of aircraft be developed. Recognizing this need, NASA Lewis Research Center, McDonnell Douglas Aircraft, and DARPA defined a cooperative program for testing in the NASA Lewis 9- by 15-Foot Low Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion, one of the technologies critical to STOVL. Results from a test program are presented along with a discussion of the facility modifications allowing this type of testing at model scale. These modifications to the tunnel include a novel ground plane, an elaborate model support which included 4 degrees of freedom, heated high pressure air for nozzle flow, a suction system exhaust for inlet flow, and tunnel sidewall modifications. Several flow visualization techniques were employed including water mist in the nozzle flows and tufts on the ground plane. Headwind (free-stream) velocity was varied from 8 to 23 knots.

Johns, Albert L.↗
NASA NTRS1988

Hot gas ingestion testing of an advanced STOVL concept in the NASA Lewis 9- by 15-foot Low Speed Wind Tunnel with flow visualization

Advanced Short Takeoff/Vertical Landing (STOVL) aircraft capable of operating from remote sites, damaged runways, and small air capable ships are being pursued for deployment around the turn of the century. To achieve this goal, it is important that the technologies critical to this unique class of aircraft be developed. Recognizing this need, NASA Lewis Research Center, McDonnell Douglas Aircraft, and DARPA defined a cooperative program for testing in the NASA Lewis 9- by 15-foot Low Speed Wind Tunnel (LSWT) to establish a database for hot gas ingestion, one of the technologies critical to STOVL. Results from a test program are presented along with a discussion of the facility modifications allowing this type of testing at modal scale. These modifications to the tunnel include a novel ground plane, an elaborate model support which included 4 degrees of freedom, heated high pressure air for nozzle flow, a suction system exhaust for inlet flow, and tunnel sidewall modifications. Several flow visualization techniques were employed including water mist in the nozzle flows and tufts on the ground plane. Headwind (free-stream) velocity was varied from 8 to 23 knots.

Johns, Albert L.↗
NASA NTRS1992

Severe turbulence and maneuvering from airline flight records

Digital flight records from reported clear-air turbulence incidents are used to determine winds, to determine maneuver G loads, and to analyze control problems. Severe turbulence is found downwind of mountains and thunderstorms associated with vortices in atmospheric waves. It is also found in strong updrafts above thunderstorm buildups that are not detected by onboard weather radar. An important finding is that there are large maneuvering loads in over half of the reported clear-air turbulence incidents. Maneuvering loads are determined through an analysis of the short-term variations in elevator deflection and aircraft pitch angle. For altitude control in mountain waves the results indicate that small pitch angle changes with proper timing are sufficient to counter the vertical winds. For airspeed control in strong mountain waves, however, there is neither the available thrust nor the quickness in engine response necessary to counter the large and rapid variations in horizontal wind.

Wingrove, R. C.↗
NASA NTRS1958

The measured and estimated rotary stability derivatives of the X-15 airplane

Measurements of the rotary derivatives of the X-15 aircraft were made in several of the wind tunnels of the National Advisory Committee for Aeronautics. The speed range was from landing speed up to Mach number, 3.5. The measurements were made on the steady-state, forced-oscillation equipment. The apparatus measures the rotary derivatives during small-amplitude, single-degree-of-freedom oscillations. In this paper the results of the wind-tunnel tests are compared with the values of the rotary derivatives estimated by the available procedures. Whenever possible, the results of wind-tunnel measurements of the static forces and moments on the X-15 have been utilized in the estimation procedures to obtain lift-curve slopes and centers of pressure of the tail surfaces. In this way, at least a partial account is taken of the effects of the fuselage and wing downwash and pressure field on the tail surfaces.

Tinling, Bruce↗