SEARCH · Engineering Papers

Results for “small reactors”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

DOE OSTI2020

The passivity of low-temperature carburized austenitic stainless steel AISI-316L in a simulated boiling-water-reactor environment

The passive film on low-temperature-carburized AISI-316L austenitic stainless steel was studied in an oxygenated, simulated boiling-water-reactor environment with normal water chemistry. The microstructure was studied using scanning electron microscopy, grazing-incidence X-ray diffractometry, Auger electron spectroscopy, X-ray energy-dispersive spectroscopy, and transmission electron microscopy. For non-surface engineered AISI-316L, three distinct layers were observed after exposure: an outer layer of larger nickel-oxide enriched particles with the spinel structure, an intermediate layer of small Cr-oxide-enriched hematite particles, and a compact inner layer of Cr-enriched oxide also having the spinel structure. Exposure of low-temperature-carburized AISI-316L, in contrast, resulted in only two distinct layers. These layers did not include a compact Cr-rich inner layer. Instead, the innermost layer consisted of an oxide with the spinel structure that was a mixture of Fe, Cr and Ni oxide. The outer layer on the low-temperature-carburized specimen consisted of large loosely stacked particles with the spinel structure of mixed composition. In addition to passive-film characterization, the corrosion rate was studied by monitoring mass loss. Finally, after 500 h of immersion, the mass changes measured were relatively low for all specimens indicating good adhesion and low oxidation rates.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Design of a gas-solid-solid separator to remove ash from circulating fluidized bed reactors

Cyclones are one of the most common types of gas-solid separators used in circulating fluidized bed boilers. However, cyclones typically do not allow ash to leave the system through the cyclone exit, causing ash to build up in the fluidized bed and necessitating additional systems to remove ash that builds up in the bed. In this study, an alternative “disengager” gas-solid separator is proposed as a way of inherently separating small and large solids, resulting in a gas-solid-solid separation system where ash is allowed to leave the system along with gas while the desired fluidized bed material is retained. Unlike cyclones, which rely on centrifugal force to separate solids and gas, the disengager separates based on entrainment velocity of the particles. Upwards-flowing gas and particles strike a deflection plate and enter the disengaging chamber where particles with low terminal velocity such as ash fines flow with the gas, while larger particles such as sand fall to the bottom of the separator and are returned to the fluidized bed. In this study, several different proposed disengager configurations are simulated and compared to a typical cyclone using computational fluid dynamic (CFD) simulations. Furthermore, it was found that separation efficiency in the disengager is strongly influenced by the size of the deflection plate, rather than by the size of the unit itself. The predicted separation efficiency showed that compared to a cyclone, the disengager design allows significantly more ash to exit the system but retains a similar amount of desirable material. Additionally, the disengager was predicted to not suffer significantly more erosion that a cyclone.

42 ENGINEERING↗

DOE OSTI2025

SPC-71250 Rev 0 MARVEL Upper Shield Build to Print Fabrication Specification

Idaho National Laboratory (INL) is developing a microreactor to produce electrical power utilizing a small nuclear core under the Microreactor Application Research Validation and Evaluation (MARVEL) program. This procurement specification defines the requirements for fabrication of the Upper Shield Assembly.

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

DOE OSTI2021

Decrypting bacterial polyphenol metabolism in an anoxic wetland soil

Abstract Microorganisms play vital roles in modulating organic matter decomposition and nutrient cycling in soil ecosystems. The enzyme latch paradigm posits microbial degradation of polyphenols is hindered in anoxic peat leading to polyphenol accumulation, and consequently diminished microbial activity. This model assumes that polyphenols are microbially unavailable under anoxia, a supposition that has not been thoroughly investigated in any soil type. Here, we use anoxic soil reactors amended with and without a chemically defined polyphenol to test this hypothesis, employing metabolomics and genome-resolved metaproteomics to interrogate soil microbial polyphenol metabolism. Challenging the idea that polyphenols are not bioavailable under anoxia, we provide metabolite evidence that polyphenols are depolymerized, resulting in monomer accumulation, followed by the generation of small phenolic degradation products. Further, we show that soil microbiome function is maintained, and possibly enhanced, with polyphenol addition. In summary, this study provides chemical and enzymatic evidence that some soil microbiota can degrade polyphenols under anoxia and subvert the assumed polyphenol lock on soil microbial metabolism.

59 BASIC BIOLOGICAL SCIENCES↗

DOE OSTI2022

Enhancing Coking Tolerance and Stability of SOFC Anodes Using Atomic Layer Deposition (ALD) of Oxide Thin Films

The overall objective of this project was to use atomic layer deposition (ALD) to add modifiers to the surfaces of conventional Ni-YSZ cermet, solid oxide fuel cell (SOFC) anodes to enhance both their tolerance to hydrocarbon fuels by decreasing their propensity to form coke deposits, and to increase redox stability. Studies of the use of ALD to modify analogous supported metal powder catalysts were also added to the scope of the project in response to our industrial partner, Atrex going out of business. The initial portion of the program focused on designing and building the ALD reactor required for deposition of the oxide modifier films. Studies of the oxide modifier films on the coking tolerance and of redox properties of Ni-cermet anodes were then carried out. These studies demonstrated that while surface oxide modifiers were able to impart some coking resistance this only occurred for a relatively small range of operating conditions (e.g., temperature, steam-to-fuel ratio, etc.) and not at the level that would be required for operating in methane fuel at low steam-to-methane ratios. In light of this observation, we focused on assessing another approach to enhance anode coking resistance which eliminated bulk Ni from the anode. This approach made use of electronically conducting perovskite films to provide electrical conductivity in the anode, while using small amounts of Ni or other metals, such as Pt, deposited using ALD as the anode oxidation catalyst. This approach proved to be quite promising at both imparting coking resistance and redox stability.

03 NATURAL GAS↗

DOE OSTI2025

Modular Processing of Flare Gas for Carbon Nanoproducts

This project demonstrated the technical viability and economic promise of a modular system for converting flared natural gas into valuable carbon nanoproducts (CNPs) through catalytic chemical vapor deposition (CVD). All major project milestones were successfully completed, including reactor design and commissioning, catalyst development, process optimization, technoeconomic analysis, and application testing in concrete systems. The overarching goal was to create a scalable, field-deployable process that valorizes stranded methane by producing high-value carbon materials for use in cementitious composites. At the lab scale, the team designed and built a fluidized bed reactor optimized for use with silica fume-supported nickel catalysts synthesized via atomic layer deposition (ALD). A statistically designed sintering study enabled precise tuning of nickel nanoparticle size, identifying the influence of oxygen partial pressure, time, and temperature on catalyst morphology and performance. These insights allowed the team to target catalyst conditions that maximize carbon nanofilament growth. Subsequent CVD experiments achieved up to 31.8 wt% carbon deposition under optimized conditions, with TEM confirming the presence of nanofilament structures and sustained hydrogen evolution during reaction. Reactor upgrades and empirical fluidization studies supported the development of reliable, repeatable experimental protocols. The modular pilot-scale skid reactor was fully constructed, instrumented, and commissioned. Capable of operating at 675–800°C and pressures up to 290 psig, the system was designed for continuous operation at a carbon production rate of 1 kg/hr. Initial demonstration runs confirmed solids handling, thermal control, and system leak-tightness, although a critical reactor component (the downfeed tube) was inadvertently omitted during final assembly. This omission limited gas–solid contact and prevented meaningful carbon deposition during pilot-scale CVD runs. Nonetheless, the system operated safely under design conditions, and the root cause of performance limitations was clearly identified. Complementary work on UHPC formulations demonstrated that small additions of carbon nanoproducts, including those derived from flare gas, can significantly enhance mechanical performance while preserving workability. A comprehensive study of CNF dispersion techniques and mix design optimization led to a clear protocol for integrating these nanomaterials into concrete. Incorporation of CNPs improved flexural toughness and reduced porosity, supporting their use in high-performance infrastructure applications. A technoeconomic analysis (TEA) confirmed that this process can produce CNP-loaded catalyst material at a levelized cost below $\$$7/kg across a range of catalyst loadings and reaction yields. With estimated market values for the carbon composite product ranging from $\$$14 to over $\$$60/kg, and the ability to blend CNPs into concrete at sub-percent levels with less than 10% added cost, the system presents a compelling economic case. While additional engineering work is needed to optimize fluidization and heat transfer at scale, this project establishes a strong foundation for commercial development. The process is not only technically sound but also economically promising, representing a viable pathway for flare gas mitigation through modular carbon nanomaterial production.

03 NATURAL GAS↗

DOE OSTI2024

Impacts of future nuclear power generation on the international monitoring system

Many countries are considering nuclear power as a means of reducing greenhouse gas emissions, and the IAEA (IAEA, 2022) has forecasted nuclear power growth rates up to 224% of the 2021 level by 2050. Nuclear power plants release trace quantities of radioxenon, an inert gas that is also monitored under international agreements as a signature of nuclear weapons tests. To better understand how nuclear energy growth (and resulting Xe emissions) could affect this global nonproliferation architecture, we modeled daily releases of radioxenon isotopes used for nuclear explosion detection in the International Monitoring System (IMS) that is part of the Comprehensive Nuclear Test-Ban Treaty: 131m Xe, 133 Xe, 133m Xe, and 135 Xe to examine the change in the number of radioxenon detections as compared to the 2021 detection levels. If a 40-station IMS network is used, the detections of 133 Xe in 2050 would range from 82% for the low-power scenario to 195% for the high-power scenario, compared to the detections in 2021. If an 80-station IMS network is used, the detections of 133 Xe in 2050 would range from 83% of the 2021 detection rate for the low-power scenario to 209% for the high-power scenario. Essentially no detections of 131m Xe and 133m Xe are expected. The high growth scenario could lead to a six-fold increase in 135 Xe detections, but the total number of detections is still small (on the order of 1 detection per day in the entire network).

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Elevated temperature nanoscratch of Inconel 617 Superalloy

Inconel 617 superalloy is a main candidate to be used for mechanical and tribo-components in high temperature helium-cooled reactors. Recent findings show that it grows a unique surface oxide, especially under high temperature helium with distinct wear, friction, and contact properties. Here, this study reports the elevated temperature nanoscratch behavior of Inconel 617 and further utilizes it to understand the effect of temperature on contact friction constituent contributors, adhesion and plowing at small scales. Inconel 617 is aged in high temperature helium, and consequently, the total kinetic friction coefficient of the alloy surface oxide is obtained in temperatures ranging from 25 °C to 400 °C. A finite element model is developed and validated based on the experimental results. The model is then utilized along with previously established techniques to determine the adhesion and plowing components of the friction coefficient. At small scale, the experimental results show that with increasing temperature the friction coefficient increases. It was inferred that this increase is mainly due to the increased contribution of plowing friction at high levels of deformation.

36 MATERIALS SCIENCE↗

DOE OSTI2023

H 2 generation by the 10 B(n,α) 7 Li reaction in high temperature water

H 2 produced in water from the 10 B(n,α) 7 Li fission reaction has been measured up to 300 °C. Thermal energy neutrons from the Rhode Island Nuclear Science Center's 2 MW reactor interact with boric acid-containing water in temperature-controlled high-pressure cells made from tubing of either titanium or zirconium alloy. After exposure for a minimum of 1 h, the solution sample is extracted and sparged with argon. The H 2 entrained by the sparging gas is sampled with a small mass spectrometer. A small amount of sodium is included in the boric acid solution so that after sparging, samples can be collected for 24 Na activation measurements in a gamma spectrometer to determine the neutron exposure and thus the total energy deposited in solution. The G-value (μmol/J) for H 2 production is obtained for water at a pressure of 25 MPa, over a temperature range from 20 °C to 300 °C. The weak temperature dependence of this yield between 150 °C and 200 °C demonstrates that the bimolecular reaction of pairs of e$^{–}_{aq}$ is a very minor source of H 2 in high LET tracks.

10B↗

DOE OSTI2021

Pulsed Thermal Tomography Nondestructive Examination of Additively Manufactured Reactor Materials and Components. Third Annual Progress Report

Additive manufacturing (AM) of high-strength corrosion resistance alloys for nuclear energy applications, such as stainless steel and Inconel, is currently based on laser powder bed fusion (LPBF) process. Some of the challenges with using LPBF method for nuclear manufacturing include the possibility of introducing pores into metallic structures. Probability of crack initiation at the pore depends on size, shape, and orientation of the defect. Pulsed Infrared Thermography Imaging (PIT) provides a capability for non-destructive evaluation (NDE) of sub-surface defects in arbitrary size structures. The PIT method is based on recording material surface temperature transients with infrared (IR) camera following thermal pulse delivered on material surface with flash light. The PIT method has advantages for NDE of actual AM structures because the method involves one-sided non-contact measurements and fast processing of large sample areas captured in one image. Following initial qualification of an AM component for deployment in a nuclear reactor, a PIT system can also be used for in-service nondestructive evaluation (NDE) applications. In this report, we describe recent progress in enhancing PIT capabilities in detecting microscopic subsurface defects in metals, and classifying shapes and orientation of pores in thermal images. For detection of microscopic defects in PIT imaging data, we have developed Spatial Temporal Denoised Thermal Source Separation (STDTSS) unsupervised machine learning (ML) image processing algorithm. We show that flat bottom hole (FBH) defects as small as 200µm in SS316 and IN718 specimens, can be detected with STDTSS algorithm. To the best of our knowledge, these are the smallest detected defects which are reported in literature. For classification of defects shapes, we have previously developed thermal tomography (TT) algorithm to obtain depth reconstructions of material defects from data cube of sequentially recorded surface temperatures. However, interpretation of TT images is non-trivial because of blurring with increasing depth. To address this challenge, we have developed a deep learning convolutional neural network (CNN) to classify size and orientation subsurface defects in simulated TT images.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Applicability study of Bayesian optimization in core neutronic design using a toy model

At the Japan Atomic Energy Agency (JAEA), an innovative design approach named ARKADIA (Advanced Reactor Knowledge- and AI-aided Design Integration Approach through the whole plant life cycle) for advanced nuclear reactors is currently under development. One task in ARKADIA is to build a system that automatically optimizes core and fuel designs by conducting core neutronic and thermal-hydraulic calculations, fuel integrity evaluations, and plant dynamic analyses. This system will be implemented to automatically find an optimal design that minimizes (or maximizes) objective function defined by core performance while varying the core and fuel design parameters such as fuel pin diameter, core height and diameter. In this study, as the first step of system development, we focused only on core neutronic design and conducted a study of automatic optimization. As the optimization algorithm, Bayesian optimization (BO), an effective method for optimization problems with expensive computational cost of objective function, was utilized. The applicability of BO was studied based on single- and two-objective optimization examples of core neutronic design in a toy model. As a result, in the former, it was shown that BO can give the optimal solution, which matches the reference solution calculated by a brute force calculation well, with a small number of required calculations. Usability on core neutronic designs, where the computational cost per case is high, was confirmed. In the latter, it was found that BO can give a Pareto solutions-set that shows good agreement with the reference solution. (authors)

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2025

Oxide Dispersion Strengthened Ferritic Steel Wire Feedstock Development for Larger Format Additive Manufacturing (CRADA Final Report)

This CRADA project funded through DOE’s INFUSE program sought to demonstrate the viability of fabricating large, complex parts from oxide dispersion strengthened (ODS) steel with advanced manufacturing. Exhibiting excellent radiation tolerance and high mechanical performance at elevated temperatures, ODS steel is a promising structural material candidate for near-plasma components in fusion energy systems. Its use, however, has been limited by a lack of manufacturability. This project sought to produce ODS steel wire through a solid-state shear assisted extrusion process and then demonstrate that the wire can undergo controlled local melting while being welded with the final part sufficiently retaining the beneficial properties of ODS steel. This would allow the use of wire-arc additive manufacturing (WAAM) to manufacture large-scale ODS parts, even though ODS is currently only available as a powder. WAAM is a promising technique for producing components like the replaceable ARC vacuum vessel in CFS’ fusion reactor design. Meanwhile, this project will also expand PNNL’s capability in producing custom wire feedstock with friction extrusion, enabling downstream large-scale manufacturing with WAAM and solid-state based additive manufacturing. The project achieved its goals of developing tooling and fixturing to produce ODS wire at smaller diameters than previous projects. Several small lengths of wire of 1.5 mm and 2.5 mm diameter in the range of 2.5-30 mm long were produced at tool temperatures that are known to cause ODS particle coarsening (~1200 °C). Fixtures and tooling for longer (>1 m) wires were developed but further process development is needed reduce tool temperature during extrusions and to increase wire length needed for WAAM testing and development.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Corrosion evaluation of metal foams in eutectic molten salts for high temperature latent heat energy storage application

High-temperature Thermal Energy Storage (TES) has drawn great attention as a technology that can increase the role and profitability of micro nuclear reactors in the decentralized clean energy market. Various research needs have been proposed by Idaho National Laboratory (INL) in "the Integrated Energy Systems: 2020 Roadmap" with the goal of utilizing the high temperature of 550 degrees or more generated in the 4th generation reactor to industrial purposes from the standpoint of integrated energy systems [1]. With the recent development of the 4th generation nuclear power plant, including micro nuclear reactor, there is a great deal of interest in researching how to efficiently couple a heat source to an industrial process through thermal processing. Texas A&M University (TAMU) and INL are currently collaborating to develop a novel latent heat storage design called HITB (Heat pipe-Integrated Thermal Battery). As part of the small-scale experimental demonstration research for HITB, a study for storage medium selection was conducted at TAMU. Eutectic salts have attracted interest as high-temperature heat storage medium for HITB. Especially, chloride molten salts and fluoride molten salts are considered promising candidates due to their high melting temperature, thermal stability, and high latent heat of fusion. Since eutectic salts have poor thermal conductivity in general, it is critical to distribute materials with high thermal conductivity evenly to facilitate the charging and discharging of heat. In this study, metal foam was considered in the HITB system to overcome the poor heat transfer characteristics of eutectic salts. In order to improve heat transfer, it is necessary to study materials with high thermal conductivity, corrosion resistant to molten salts, such as fins, extended surfaces, particles, microcapsulation, or foam structure. Porous structure of copper or aluminum can increase heat transfer area, form a thermal transfer network, and increase the effective thermal conductivity of thermal storage medium [2]. Since the melting temperature is required to be at least 450? in the current HITB design, various eutectic salts are being considered. FLiNaK and FLiBe, which are famous for fluoride salts, are good candidates, but due to the sharp rise in the price of LiF recently, they are excluded for economic reasons to be applied to large-capacity thermal energy storage. On the other hand, chloride salts are very cheap and easy to obtain, have a high melting temperature, and have a high latent heat of fusion, so they are recently in the spotlight as a phase change material. However, because of the hygroscopic nature of chloride salts, HCl gas due to impurity is easy to be released and is particularly vulnerable to corrosion. Chloride eutectic salts have been tested and suggested for metal alloys that are particularly resistant to corrosion, such as SS304, SS316, Hastelloy, Inconel 625, Incoloy 800H, which has low thermal conductivity, and is very expensive [3-6]. Porous materials with high thermal conductivity such as copper and aluminum have been tested for stability in fluids such as paraffin or water as metal foam or metal fin structures, but high temperature corrosion tests were not performed on various eutectic salts yet. Therefore, this study investigated the high temperature corrosion characteristics of metal alloys, such as C10100 foam, C10100 plate, 6101 alloy foam, and SS316 plate, while immersed in the candidate eutectic salts. A total of 20 tests for SS316 coupons and 10 tests for C10100 coupons were performed to ensure the repeatability of the present measurements. Since it is difficult to completely remove the salt inside metal foam due to the complex inner structure of the metal foam, only the surface condition was observed with a microscopy and scanning electron microscopy (SEM) image, except for measuring the corrosion rate and average mass loss.

25 ENERGY STORAGE↗

DOE OSTI2025

Design of a separate effects MiniFuel irradiation experiment investigating microstructure evolution in high burnup UO 2

The microstructural evolution of UO 2 fuel pellets during commercial operation in light water reactors (LWRs) is known to vary significantly across the pellet radius due to spatial variations in local temperature and burnup. The primary obstacle to extending LWR refueling cycles to 24-month intervals is the susceptibility of certain high burnup fuel microstructures to fuel fragmentation, relocation, and dispersal (FFRD) during a loss of coolant accident (LOCA). Although FFRD of the high burnup structure in the rim region of a pellet is well studied, the fine fragmentation that has been observed in a second region, near the midradius of the pellet (termed the “dark zone”) following mock LOCA testing of high burnup commercial fuel rods is less understood. This paper describes the design, analysis, and execution of a separate effects MiniFuel irradiation experiment that aims to identify the specific temperature and burnup regimes under which FFRD-susceptible dark zone microstructures form. The small disc specimens (3 mm diameter by ∼0.3 mm thick) enable more precise control of the relatively uniform temperature and burnup conditions. A total of 42 specimens were fabricated with typical LWR fuel densities (∼96%–98% of theoretical density) and grain sizes (∼12 μm) and are being irradiated over a range of temperatures (600°C–1000°C) and discharge burnups (50–72 MWd/kg-U) that bound the midradius region of high burnup LWR fuel. Fuel specimens with identical 235 U enrichments were inserted in two irradiation locations in the High Flux Isotope Reactor and are currently undergoing irradiation to further evaluate the impact of rate effects (fission rate, time at temperature) on the microstructural evolution. The fuel fabrication and the thermal and neutronic simulations used for designing the experiment are detailed in this paper. A secondary objective of the experiment is to observe fission gas release (FGR) under the various irradiation conditions, and this work provides first-order predictions of FGR from all fuel specimens. The insights gained from these experiments will inform future high burnup core designs that could minimize the formation of susceptible microstructures and ultimately enable 24-month refueling cycles while minimizing the fraction of the fuel susceptible to FFRD.

FFRD↗

DOE OSTI2025

SPC-71188 Rev 0 MARVEL Control Drum Rotary Shaft Seal Procurement Specification

21 - SPECIFIC NUCLEAR REACTORS AND ASSOCIATED PLAN↗

DOE OSTI2024

Investigation of Frozen Chemistry for Molten Salt Reactors (MSRs)

Understanding accident progression and the potential/conditions for fission product release from fuel is necessary to evaluate safety for any nuclear reactor system. Molten Salt Reactors (MSRs) under development need such analysis to support safety evaluations. Fission product chemistry specific to MSR concepts is a critical area that introduces distinct considerations relative to the current state-of-knowledge in reactor safety, primarily developed for water-moderated nuclear reactor systems. In Light Water Reactor (LWR) systems, it is necessary to capture the chemical interaction of fission products with the reactor evironment, containment and confinement systems. The overall effects at this point are relatively well understood for the purposes of performing safety evaluations. A key insight from LWR studies is that fission product chemical behavior can be reasonably captured by modeling approaches where the chemistry is "frozen". These modeling approaches assume that radionuclide reaction and speciation can be represented by chemical classes, each with characteristic transport behavior that is invariant under a broad range of thermochemical conditions. However, radionuclides can exhibit a range of behavior in the liquid salt-melt phase of the coolant used in MSRs. Radionuclides, salt, and the metal containment surfaces (i.e. pipes) can co-exist in dynamic equilibrium that could evolve with small system mass changes. A detailed investigation to the degree the equilibrium state can dynamically evolve with changes in the conditions of the molten salt mixture has not been previously conducted. It is currently not well understood where frozen chemistry assumptions are valid. Expanding the state-of-knowledge in this regard is relevant to better assessing the range of chemical effects that should be incorporated as part of MSR safety assessments. This investigation used the Oak Ridge Isotope GENeration (ORIGEN) module of the Standardized Computer-Analysis for Licensing Evaluation (SCALE) code to generate simulated radionuclide inventories for the MSR Experiment (MSRE) and then modeled reactor chemical speciation using the Molten Salt Thermodynamic Database – Thermochemical (MSTDB-TC) coupled with Thermochimica. The effect of composition variation during decay of fission product inventory in a molten salt over a period of 500 days prolonged post- at multiple temperatures was studied. Mass fractions for fluorine and berilium were varied in order to probe the effects of free fluorine control. Finally, speciation of fluoride reactors were showed by comparing MSRE readionuclide inventories with a FLiBe based molten salt breeder reactor (MSBR). The results showed that fission product mass change has little effect on phase mass changes and vapor pressures for fluoride species, but differ with varying carrier and fuel salt compositions. However, iodine species were found to have a vapor pressure not only dependent on temperature, but also the free fluorine potential, releasing iodine when the free fluorine potential is equal to the iodine inventory. This observation, however, arose under free fluorine potentials that are very unlikely to be realized in typical molten salt mixtures. Despite this observation, temperature was found to be the dominant parameter that drove phase change and fission product species vapor pressure. The results indicate that the current frozen chemistry approach is adequate for MSR analysis.

22 GENERAL STUDIES OF NUCLEAR REACTORS↗

DOE OSTI2022

Control of neutral fueling and helium exhaust to NSTX-U plasmas by means of three-dimensional magnetic control fields

Resonant magnetic perturbations are used to stabilize plasma edge instabilities, so-called edge localized modes (ELMs), in high-performance (H-mode) plasmas explored for fusion energy. These ELMs cause repetitive outburst of confined energy and particles and cause cyclic loading of plasma facing components (PFCs). This endangers the integrity of the PFCs and hence limits the lifetime and hence commercial viability of fusion. It was shown that these ELMs can be stabilized by application of small amplitude resonant magnetic perturbation (RMP) fields. This removes the ELMs as edge instabilities but also induces three-dimensional (3D) effects to the plasma boundary, which was formerly toroidally axisymmetric. The impact of this 3D perturbation on the plasma boundary solution needs to be understood to extrapolate the effects to ITER and towards a fusion reactor, if ELM control by RMP fields would be utilized.

3D Boundary Plasmas↗

DOE OSTI2024

Numerical simulation of involute-plate research reactor flow behavior using RANS, LES and DNS

This paper investigates the flow behavior of involute-plate research reactors by performing Reynolds-Averaged Navier Stokes simulation (RANS), Large Eddy Simulation (LES) and Direct Numerical Simulation (DNS) of the channel flow between fuel plates. By modeling turbulence with different numerical approaches, this study provides data with three levels of fidelity. For the RANS simulation, three widely used turbulence models, i.e., k-ε, k-ω, Reynolds Stress Turbulence model (RST) are applied by using the commercial CFD code STAR-CCM +. For LES and DNS, the open-source CFD code, Nek5000, is used given its outstanding scalability on High Performance Computer (HPC) and high-order technique. The results from RANS simulations are compared with that from LES and DNS for benchmarking. Both macroscale parameters and turbulence statistics, such as velocity magnitude, lateral velocity and turbulence kinetic energy, are presented and analyzed. The results from RANS simulation achieve good agreement with LES and DNS on velocity and turbulence kinetic energy prediction. The RST turbulence model predicts the most similar flow pattern of lateral velocity as compared to LES and DNS. The Lambda-2 (λ2) criterion with a reasonable threshold is used to demonstrate the instantaneous vortices distribution in the involute channel from both LES and DNS calculation. The DNS simulation captures more detailed turbulence especially near the corner, which explains the discrepancy between LES and DNS results near the corner. The normalized RMS error are defined and calculated to assess the performance of those turbulence models. The RST model captures the anisotropic feature of turbulence, which enable it to outperform other turbulence models for predicting the flow behavior in an involute channel. Although some discrepancies are found between LES and DNS results in the corner, the overall deviations between LES and DNS are found to be small. In conclusion, given that the computational cost of DNS calculation is an order of magnitude higher, using LES data for benchmarking RANS model is a cost-effective approach.

DNS↗