SEARCH · Engineering Papers

Results for “shear stress”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

NASA NTRS1993

On the shear stabilization of capillary break-up of finite liquid bridges

In this paper we consider an isothermal finite liquid bridge under zero-gravity. A sinusoidal interfacial shear stress drives a nonparallel flow in the bridge. The linear stability of this flow to three-dimensional disturbances (which may deform the cylindrical gas-liquid interface) is determined numerically by solving an elliptic eigenvalue problem. Previous results on shear stabilization of capillary break-up of axially unbounded cylindrical interfaces containing a parallel flow are hereby extended to a nonparallel flow. The turning flow regions influence the stability significantly. However, for the particular cases considered, a small area in parameter space remains where the capillary instability is suppressed through interfacial shear. Second, non-axisymmetric oscillatory instabilities are found which originate from an interaction of the interface deformation and the basic flow. These instabilities may be the isothermal limit of the oscillatory instabilities observed in float-zone crystal growth.

Dijkstra, Henk A.↗

NASA NTRS2017

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

Full seven-equation Reynolds stress turbulence models are promising tools for today’s aerospace technology challenges. This paper examines two such models for computing challenging turbulent flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSG/LRR full second-moment Reynolds stress models have been implemented into the FUN3D (Fully Unstructured Navier-Stokes Three Dimensional) unstructured Navier-Stokes code and were evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results computed using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST-V) two-equation turbulence models.

reynolds averaging↗

NASA NTRS2017

Evaluation of Full Reynolds Stress Turbulence Models in FUN3D

Full seven-equation Reynolds stress turbulence models are a relatively new and promising tool for todays aerospace technology challenges. This paper uses two stress-omega full Reynolds stress models to evaluate challenging flows including shock-wave boundary layer interactions, separation and mixing layers. The Wilcox and the SSG/LRR full second-moment Reynolds stress models have been implemented into the FUN3D (Fully Unstructured Navier-Stokes Three Dimensional) unstructured Navier-Stokes code and are evaluated for four problems: a transonic two-dimensional diffuser, a supersonic axisymmetric compression corner, a compressible planar shear layer, and a subsonic axisymmetric jet. Simulation results are compared with experimental data and results using the more commonly used Spalart-Allmaras (SA) one-equation and the Menter Shear Stress Transport (SST-V) two-equation turbulence models.

reynolds averaging↗

DOE OSTI2025

Quantifying precursors to void nucleation and coalescence in aluminum

Ductile rupture is a common failure mode for engineering alloys. It is generally comprised of three mechanisms: void nucleation at secondary particles, void growth, and coalescence of voids. Conventional models for ductile rupture have limited precision for predicting macroscopic failure. This is partially because they have been corroborated using ex-situ observations of these three mechanisms and calibrated by macroscopic strain or stress metrics. In this study, in-situ high-energy X-ray characterization was conducted to correlate sites of void nucleation via particle cracking and sites of void growth with grain-scale metrics. Here it is shown that particle cracking is not predicated by elevated stress metrics, which disagrees with classical models. Instead, particle cracking tended to occur for the largest, least spherical particles. This trend persisted on the aggregate-scale and within individual neighborhoods around particles. Furthermore, an Eshelby analysis illuminated a statistically significant increase in maximum principal stress within a cracked particle, compared to an uncracked particle. In-situ observations also revealed two separate examples of intragranular void growth comprised of flat, crack-like features that grew showing alignment with slip systems of the highest resolved shear stress. Post-mortem fractography revealed a secondary population of dimples on these crack-like features, implying that void sheeting may be occurring during this crack-like void growth. Furthermore, these in-situ observations imply that classical models for void growth, that assume a homogenous medium, should be extended to account for the anisotropic grain-level behavior to correctly capture distinct features of void nucleation and growth.

Al-2219↗

NASA NTRS1988

Simulated impact damage in a thick graphite/epoxy laminate using spherical indenters

A study was made to determine the extent of fiber damage caused by low-velocity impact of spherical impactors to a very thick graphite/epoxy laminate. The laminate was cut from a filament wound case being developed for the Space Shuttle solid rocket motors. The case was wound using a wet process with AS4W graphite fiber and HBRF-55A epoxy. Impacts were simulated under quasi-static conditions by pressing hemispherically shaped indenters against the laminate at different locations. The contact force and indenter diameter were varied from location to location. The forces were chosen for each indenter diameter to produce contact pressures below and above that required to initiate damage. After the forces were applied, the laminate was cut into smaller pieces so that each piece contained a test site. The pieces were then deplied and the individual plies examined to determine the extent of fiber damage. Broken fibers were found in the outer layers directly beneath the contact site. The locus of broken fibers in each layer resembled a crack normal to the direction of the fibers. The maximum length and depth of the cracks increased with increasing contact pressure and indenter diameter. The internal stresses in the laminate were calculated using Hertz's law and Love's solution for pressure applied on part of the boundary of a semi-infinite body. The maximum length and depth of the cracks were predicted using a maximum shear stress criterion. Predictions and measurements were in good agreement.

Poe, C. C., Jr.↗

NASA NTRS1998

Determination of Yield and Flow Surfaces for Inconel 718 Under Axial-Torsional Loading at Temperatures Up to 649 C

An experimental program to determine flow surfaces has been established and implemented for solution annealed and aged IN718. The procedure involved subjecting tubular specimens to various ratios of axial-torsional stress at temperatures between 23 and 649 C and measuring strain with a biaxial extensometer. Each stress probe corresponds to a different direction in stress space, and unloading occurs when a 30 microstrain (1 micro eplison = 10(exp -6) mm/mm) offset is detected. This technique was used to map out yield loci in axial-torsional stress space. Flow surfaces were determined by post-processing the experimental data to determine the inelastic strain rate components. Surfaces of constant inelastic strain rate (SCISRS) and surfaces of constant inelastic power (SCIPS) were mapped out in the axial-shear stress plane. The von Mises yield criterion appeared to closely fit the initial loci for solutioned IN718 at 23 C. However, the initial loci for solutioned IN718 at 371 and 454 C, and all of the initial loci for aged IN718 were offset in the compression direction. Subsequent loci showed translation, distortion, and for the case of solutioned IN718, a slight cross effect. Aged IN718 showed significantly more hardening behavior than solutioned IN718.

Gil, Christopher M.↗

NASA NTRS2000

Effect of Crystal Orientation on Analysis of Single-Crystal, Nickel-Based Turbine Blade Superalloys

High-cycle fatigue-induced failures in turbine and turbopump blades is a pervasive problem. Single-crystal nickel turbine blades are used because of their superior creep, stress rupture, melt resistance, and thermomechanical fatigue capabilities. Single-crystal materials have highly orthotropic properties making the position of the crystal lattice relative to the part geometry a significant and complicating factor. A fatigue failure criterion based on the maximum shear stress amplitude on the 24 octahedral and 6 cube slip systems is presented for single-crystal nickel superalloys (FCC crystal). This criterion greatly reduces the scatter in uniaxial fatigue data for PWA 1493 at 1,200 F in air. Additionally, single-crystal turbine blades used in the Space Shuttle main engine high pressure fuel turbopump/alternate turbopump are modeled using a three-dimensional finite element (FE) model. This model accounts for material orthotrophy and crystal orientation. Fatigue life of the blade tip is computed using FE stress results and the failure criterion that was developed. Stress analysis results in the blade attachment region are also presented. Results demonstrate that control of crystallographic orientation has the potential to significantly increase a component's resistance to fatigue crack growth without adding additional weight or cost.

Swanson, G. R.↗

NASA NTRS1985

A three-dimensional turbulent boundary layer undergoing transverse strain and streamwise pressure gradient

Results from an experimental investigation designed to provide data on both mean and turbulence quantities in the axisymmetric, swirling boundary layer (with and without pressure gradient) flowing over a stationary cylinder downstreams of a spinning cylindrical section are presented. The pressure gradient was introduced into the flow field by a 25.4 mm-high, forward-facing, circular step mounted on the stationary cylinder, the step height being nearly equal to the thickness of the approaching boundary layer. All the measurements were made at a nominal upstream reference Reynolds number of 2.4 x 10 to the 6th power/m (corresponding to an upstream reference velocity of 36 to 37 m/sec) with the rotation of the spinner set to make its peripheral speed equal the reference velocity. The data reported included measurements of surface pressure and the mean surface shear-stress vector taken with a miniature, directional, surface-fence gage. These measurements were supplemented by oil-flow visualization studies of the stationary cylinder. The data indicates that the streamwise pressure gradient controls the development of the streamwise component of wall shear, but leaves the peripheral component of wall shear practically unaffected.

Hebbar, S. K.↗

DOE OSTI2020

Origin of micrometer-scale dislocation motion during hydrogen desorption

Hydrogen, while being a potential energy solution, creates arguably the most important embrittlement problem in high-strength metals. However, the underlying hydrogen-defect interactions leading to embrittlement are challenging to unravel. Here, we investigate an intriguing hydrogen effect to shed more light on these interactions. By designing an in situ electron channeling contrast imaging experiment of samples under no external stresses, we show that dislocations (atomic-scale line defects) can move distances reaching 1.5 μm during hydrogen desorption. Combining molecular dynamics and grand canonical Monte Carlo simulations, we reveal that grain boundary hydrogen segregation can cause the required long-range resolved shear stresses, as well as short-range atomic stress fluctuations. Thus, such segregation effects should be considered widely in hydrogen research.

36 MATERIALS SCIENCE↗

NASA NTRS1973

Growth characteristics of a plane crack subjected to three-dimensional loading

The closed form expressions for the stress intensity factors due to concentrated forces applied to the surfaces of a half plane crack in an infinite body are used to generate solutions for distributed loads in this geometry. The stress intensity factors for uniformly distributed loads applied over a rectangular portion of the crack surface are given in closed form. An example of non-uniformly distributed loads which can be treated numerically is also included. In particular, combinations of normal and shear stresses on the crack which simulate the case of loading at an angle to the crack front are considered. The resulting stress intensity factors are combined with the strain energy density fracture criterion for the purpose of predicting the most likely direction of crack propagation. The critical value of the energy density factor can then be used for determining the allowable load on a specimen with a crack front not perpendicular to the tensile axis.

Hartranft, R. J.↗

NASA NTRS1975

A cracked sheet stiffened by several partially debonded intact or broken stringers

The effect of several stringers on the stress intensity factors at the tips of a crack is considered. The stringers which were continuously attached to the plate and placed perpendicular to the crack may be partially debonded due to high stress concentrations. Since the stringers may even break under excessive loading conditions, both intact and broken stringers are considered to investigate the effect of rupture. The continuity of displacements along the bond lines leads to an integral equation which is solved to give the shear stress distribution in the adhesive and the stress intensity factors at the crack tips.

Arin, K.↗

NASA NTRS1976

The effect of several intact or broken stringers of the stress intensity factor in a cracked sheet

The stringers which are continuously attached to the plate and placed perpendicular to the crack may be partially debonded due to high stress concentrations. Since the stringers may even break under excessive loading conditions, both intact and broken stringers are considered to investigate the effect of rupture. The continuity of displacements along the bond lines leads to an integral equation which is solved to give the shear stress distribution in the adhesive and the stress intensity factors at the crack tips.

Arin, K.↗

NASA NTRS1997

Alternative Processing Method Leads to Stronger Sapphire-Reinforced Alumina Composites

The development of advanced engines for aerospace applications depends on the availability of strong, tough materials that can withstand increasingly higher temperatures under oxidizing conditions. The need for such materials led to the study of an oxide-based composite composed of an alumina matrix reinforced with zirconia-coated sapphire fibers. Because the nonbrittle behavior of this system depends on the interface and its ability to prevent fiber-to-matrix bonding and reduce interfacial shear stress, the microstructure of the zirconia must be carefully controlled during both coating application and composite processing. When it was both porous and unstabilized, zirconia (which does not react easily with alumina) was found to be the most effective material tested in reducing interfacial shear strength between the fiber and matrix.

Jaskowiak, Martha H.↗

NASA NTRS1992

A new approach for the calculation of transitional flows

In spite of many attempts at modeling natural transition, it has not been possible to predict the streamwise intensities. A procedure is developed which incorporates some results of linear stability theory into one-equation and stress model formulations. The stresses resulting from fluctuations in the transitional region have turbulent, laminar (nonturbulent) and large eddy components. Comparison with Schubauer and Klebanoff's experiments have shown that the nonturbulent and large eddy components have a large influence on the streamwise intensities and little influence on the shear stress. Finally, predictions of the one-equation model were as good as those obtained by the stress model.

Young, T. W.↗

DOE OSTI2023

Phase transition in bilayer MoS 2 under tensile loading: a molecular dynamics study

Abstract Molybdenum disulfide (MoS 2 ), especially single-layer MoS 2 , has been experimentally and computationally discovered to exist in several different polymorphs exhibiting various electronic and mechanical properties. The morphology of MoS 2 can be tuned through strain engineering. Molecular dynamics simulations are conducted to systematically study the phase transition of single-layer MoS 2 and bilayer MoS 2 under the uniaxial tensile condition at room temperature. The roles of edge and S-line vacancy are investigated. Phase transitions are always triggered near the edge and vacancy sites. The initiation of the metastable T″ phase can release the tensile stress in the lattice, followed by I4/mmm phase initiation, regardless of the edge conditions. The growth of the I4/mmm phase can cause the local buckling of the MoS 2 plane. With a tilted S-line vacancy, I4/mmm phase is first initiated to reduce the local shear stress accumulated near the vacancy line. Overall, the phase transition mechanism of single layer and bilayer MoS 2 under the uniaxial tensile loading is provided, which guides the future strain engineering of MoS 2 in nanoelectronics applications.

Materials Science↗

NASA NTRS1982

Near-wall similarity in three-dimensional turbulent boundary layers. I - Model review. II - Pressure-driven flow results

Eleven proposed models for near-wall similarity for three-dimensional turbulent boundary layer flows are reviewed. Six of these models are comparatively simple scalar models and five are more complex and/or two-component vector models. Ten of the models can be tested as to their validity or predictive capability with the aid of measured mean velocity field, wall pressure field, and direct wall shear stress field (magnitude and direction) data. One of the models cannot be tested owing to its dependence on two parameters that are at present extremely difficult (if not impossible) to measure. Ten three-dimensional near-wall similarity models are then evaluated with direct wall shear, velocity field, and pressure gradient data from a three-dimensional pressure-driven boundary layer flow. In a primary focus of the interval where y+ is between 50 and 300, graphical results suggest that six simpler models and the freestream component of one complex model are adequate for profiles with monotone increasing skew up to about 15 deg.

Pierce, F. J.↗

NASA NTRS1989

Physical analysis and second-order modelling of an unsteady turbulent flow - The oscillating boundary layer on a flat plate

The turbulent boundary layer under a freestream whose velocity varies sinusoidally in time around a zero mean is computed using two second order turbulence closure models. The time or phase dependent behavior of the Reynolds stresses are analyzed and results are compared to those of a previous SPALART-BALDWIN direct simulation. Comparisons show that the second order modeling is quite satisfactory for almost all phase angles, except in the relaminarization period where the computations lead to a relatively high wall shear stress.

Ha Minh, H.↗

NASA NTRS1993

Geophysical models of Western Aphrodite-Niobe region: Venus

The new topography and gravitational field data for Venus expressed in spherical harmonics of degree and order up to 50 allow us to analyze the crust-mantle boundary relief and stress state of the Venusian lithosphere. In these models, we consider models in which convection is confined beneath a thick, buoyant lithosphere. We divide the convection regime into an upper mantle and lower mantle component. The lateral scales are smaller than on Earth. In these models, relative to Earth, convection is reflected in higher order terms of the gravitational field. On Venus geoid height and topography are highly correlated, although the topography appears to be largely compensated. We hypothesize that Venus topography for those wavelengths that correlate well with the geoid is partly compensated at the crust-mantle boundary, while for the others compensation may be distributed over the whole mantle. In turn the strong sensitivity of the stresses to parameters of the models of the external layers of Venus together with geological mapping allows us to begin investigations of the tectonics and geodynamics of the planet. For stress calculations we use a new technique of space- and time-dependent Green's response functions using Venus models with rheologically stratified lithosphere and mantle and a ductile lower crust. In the basic model of Venus the mean crust is 50-70 km thick, the density contrast across the crust-mantle boundary is in the range from 0.3 to 0.4 g/cm(exp -3). The thickness of a weak mantle zone may be from 350 to 1000 km. Strong sensitivity of calculated stress to various parameters of the layered model of Venus together with geological mapping and analysis of surface tectonic patterns allow us to investigate the tectonics and geodynamics of the planet. The results are presented in the form of maps of compression-extension and maximum shear stresses in the lithosphere and maps of crust-mantle boundary relief, which can be presented as a function of time. We have modeled the region of Western Aphrodite and the Niobe plains to get reasonable depths of compensation. Crust mantle boundary relief is calculated for Western Aphrodite-Niobe relative to a mean crustal thickness of 50 km. The calculations include the consequences of simple crust models and more complicated models with a weak, ductile lower crust, a strong upper mantle and a weak lower mantle layer.

Marchenkov, K. I.↗