Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “plastic crystals”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

770 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS2003

Improved Crystal Quality by Detached Solidification in Microgravity

The goals of our work on detached solidification have been to: Develop a complete understanding of all of the phenomena of detached solidification; Make it possible to achieve detached solidification reproducibly; Increase crystallographic perfection through detached solidification. Specifically, we aimed in this project to: Identify a system and develop methods that would allow viewing of the melt surface and convection in the melt during detached solidification in microgravity; Improve understanding of the origination and evolution of detachment through experiments and theoretical treatments; Achieve detachment on earth. The project resulted in 14 publications, 15 presentations, completion of 2 Ph.D. theses, and completion of 2 M.S. theses. Two additional papers are currently being reviewed for publication. Copies of most of the papers are attached as appendices. Among the accomplishments are: Achievement of detached solidification of InSb on earth and determination of the conditions favoring detachment on earth. Development of a new method for coating the interior of silica growth ampoules with transparent boron nitride, which yields the high contact angles for semiconductor melts that favor detachment. Development of a new coating for the interior of Pyrex ampoules yielding very high contact angles for water and molten organic compounds. Development of a material-balance model for steady detached solidification that provides greatly improved insight into the process, both in microgravity and on earth. Dimensionless parameters were found that clarify the role of operating conditions and physical properties. The reason for the occurrence of two steady states was clarified, along with their relative stability. Observation of periodic gas tubes during directional solidification of water and organic compounds. Gas bubbles did not propagate around the periphery to yield full detachment. Failure to obtain detachment is attributed to the ready plastic deformation of these materials, so that the frozen material continues to adhere to the ampoule wall during cooling.

Regel, Liya L.↗
DOE OSTI2022

Detecting Cage Crossing and Filling Clusters of Magnesium and Carbon Atoms in Zeolite SSZ-13 with Atom Probe Tomography

The conversion of methanol to valuable hydrocarbon molecules is of great commercial interest, as the process serves as a sustainable alternative for the production of, for instance, the base chemicals for plastics. The reaction is catalyzed by zeolite materials. By the introduction of magnesium as a cationic metal, the properties of the zeolite, and thereby the catalytic performance, are changed. With atom probe tomography (APT), nanoscale relations within zeolite materials can be revealed: i.e., crucial information for a fundamental mechanistic understanding. We show that magnesium forms clusters within the cages of zeolite SSZ-13, while the framework elements are homogeneously distributed. These clusters of just a few nanometers were analyzed and visualized in 3-D. Magnesium atoms seem to initially be directed to the aluminum sites, after which they aggregate and fill one or two cages in the zeolite SSZ-13 structure. The presence of magnesium in zeolite SSZ-13 increases the lifetime as well as the propylene selectivity. By using operando UV–vis spectroscopy and X-ray diffraction techniques, we are able to show that these findings are related to the suppression of aromatic intermediate products, while maintaining the formation of polyaromatic compounds. Further nanoscale analysis of the spent catalysts showed indications of magnesium redistribution after catalysis. Unlike zeolite H-SSZ-13, for which only a homogeneous distribution of carbon was found, carbon can be either homogeneously or heterogeneously distributed within zeolite Mg-SSZ-13 crystals as the magnesium decreases the coking rate. Carbon clusters were isolated, visualized, and analyzed and were assumed to be polyaromatic compounds. Small one-cage-filling polyaromatic compounds were identified; furthermore, large-cage-crossing aromatic molecules were found by isolating large coke clusters, demonstrating the unique coking mechanism in zeolite SSZ-13. Short-length-scale evidence for the formation of polyaromatic compounds at acid sites is discovered, as clear nanoscale relations between aluminum and carbon atoms exist.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2021

Deformation of binary and boron-doped Ni 3 Al alloys at high pressures studied with synchrotron x-ray diffraction

In situ x-ray synchrotron diffraction experiments were carried out on nickel-based high-strength superalloys under pressure to understand their deformation mechanism using a diamond anvil cell (DAC). Radial x-ray diffraction determines the room-temperature equations of state and yield strengths of binary Ni 3 Al alloy and 500 ppm boron-doped Ni 3 Al to pressures of 20 and 46 GPa, respectively. Crystallographic preferred orientations observed in these superalloys due to anisotropic stress field in DAC indicate the onset of plastic deformation. Inverse pole figure analysis reveals that the underlying deformation mechanisms change from an octahedral slip to a simultaneous activation of octahedral and cube slips upon doping with boron. The yield-strength values were found to increase with pressure and are comparable to those determined from axial diffraction experiments. The results indicate that the yield strength of Ni 3 Al:B is about 0.5 GPa higher (at pressures below 20 GPa) due to grain boundary strengthening by boron. It is shown that due to high elastic anisotropy of Ni 3 Al alloy, the yield-strength estimations from diffraction experiments strongly depend on the micromechanical model used to convert the measured elastic strains into stresses.

42 ENGINEERING↗
DOE OSTI2026

At Extreme Strain Rates, Pure Metals Thermally Harden while Alloys Thermally Soften

When materials are deformed at extreme strain rates, >10 6 s -1 , a counterintuitive mechanical response is seen where the strength and hardness of pure metals increases with increasing temperature. This anti-thermal hardening is due to dislocations meeting resistance to their motion from phonons in the crystal lattice. However, here, using optically-driven microballistic impact testing to measure dynamic strength and hardness, we show that when the composition is systematically varied away from high purity, the mechanical response of metals transitions from phonon drag of dislocations back to thermally activated pinning of dislocations, even at the highest strain rates. This boundary from “hotter-is-stronger” to “hotter-is-softer” is observed and mapped for nickel, titanium and gold. Furthermore, the ability to tune between deformation mechanisms with very different temperature dependencies speaks to new directions for alloy design in extreme conditions.

Ballistic transport↗
DOE OSTI2023

Microstructure dependent shear localization in 316L SS

Shear localization is characterized by the concentration of plastic deformation within narrow bands of material and constitutes the precursor to failure in materials subjected to high strain rates. These bands have been observed experimentally, but classical continuum material models have not been able to fully capture their development. The aim of this research is to investigate the role of microstructural differences in the dynamic shear response of wrought and additively manufactured (AM) 316L SS. Compact Forced Simple Shear specimens for Digital Image Correlation (CFSS-DIC) of wrought and additively manufactured 316L SS were tested on a Split Hopkinson Pressure Bar (SHPB) in conjunction with infrared thermometry measurements. Results indicate that the microstructures of wrought and AM 316L SS exhibit differences that affect the shear response of this materials. In conclusion, CFSS-DIC samples tested on the SHPB did not exhibit recrystallization inside the shear region, fact confirmed by thermometry measurements.

36 MATERIALS SCIENCE↗
NASA NTRS1990

The effect of hydrogen and microstructure on the deformation and fracture behavior of a single crystal nickel-base superalloy

A study was conducted on the effects of internal hydrogen and microstructure on the deformation and fracture of a single crystal nickel-base superalloy. In particular, room temperature plane strain fracture toughness and tensile tests were performed on hydrogen-free and hydrogen charged samples of PWA 1480. The role of microstructure was incorporated by varying the levels of porosity and eutectic gamma/gamma prime through hot isostatic pressing and heat treatment. The room temperature behavior of PWA 1480 was unusual because precipitate shearing was not the primary deformation mechanism at all strains. At strains over 1 percent, dislocations were trapped in the gamma matrix and an attempt was made to relate this behavior to compositional differences between PWA 1480 and other superalloys. Another unique feature of the tensile behavior was cleavage of the eutectic gamma/gamma prime, which is believed to initiate the failure process. Fracture occurred on (111) planes and is likely a result of shear localization along these planes. Elimination of the eutectic gamma/gamma prime greatly improved the tensile ductility, but pososity had no effect on tensile properties. Large quantities of hydrogen (1.74 at. percent) were gas-phase charged into the material, but surprisingly this was not a function of the amount of porosity or eutectic gamma/gamma prime present. Desorption experiments suggest that the vast majority of hydrogen is at reversible lattice trapping sites. This large, uniform concentration of hydrogen dramatically reduced the tensile strain to failure, but only slightly affected the reduction in area. Available hydrogen embrittlement models were examined in light of these results and it was found that the hydrogen enhanced localized plasticity model can explain much of the tensile behavior. K(IC) fracture toughness tests were conducted, but it was necessary to also perform J(IC) tests to provide valid data.

Walston, William S.↗
DOE OSTI2026

Role of Chemical Disorder in High Temperature Dislocation Glide in Refractory Multi-principal Element Alloys

Refractory multi-principal element alloys (RMPEAs) combine a chemically disordered lattice with a structurally ordered, single‐phase body‐centered cubic (bcc) crystal structure. Chemical fluctuations in these alloys give rise to significant energy barriers that impede dislocation motion. In this study, we use phase field dislocation dynamics to examine how spatial temperature fluctuations compete with randomness in energy barriers to affect the motion of long screw dislocations in three equi-atomic MoNbTa‐based RMPEAs: MoNbTa, MoNbTaW, and MoNbTaVW. Over a wide range of homologous temperatures (T h ≈ 0–0.6), we determined a screw dislocation ‘flow stress’ as the minimum applied stress to sustain continuous motion over a long excursion distance within a fixed timeframe. All three RMPEAs exhibit temperature dependent flow stress with three characteristic glide regimes: at low homologous temperatures, flow stress drops sharply, and screw glide remains planar and rectilinear; at intermediate homologous temperatures, the flow stress levels off as glide becomes planar but wavy; and at high homologous temperatures, flow stress plateaus as screws exhibit nonplanar, three‐dimensional motion. Glide kinetics and transition temperatures are controlled by the chemically induced fluctuations in the energy landscape. The rectilinear to wavy transition temperature is controlled by statistically weakest local barriers in the glide plane, whereas the wavy to 3D transition temperature is governed by statistically strongest local barriers. At low and intermediate homologous temperatures, the relative spread in energy barriers governs glide behavior by controlling the local kinetics of kink pair formation and kink pinning. At high homologous temperatures, the average barrier height governs the glide behavior by controlling the number of out-of-plane excursions during 3D glide. These findings reveal how random chemical fluctuations determine screw‐driven plasticity in RMPEAs, providing critical insight for the design of high temperature structural alloys.

Defects↗
DOE OSTI2020

Nucleation and growth of voids in shock loaded copper bicrystals

Understanding the evolution of damage and deformation due to spall at grain boundaries can provide a basis for connecting micro- to macroscale failure behavior in metals under extreme conditions. Copper bicrystal samples were shock loaded using flyer-plate impacts in a light gas gun with shock stresses ranging from 3 to 6 GPa. Pulse duration as well as crystal orientation along the shock direction were varied for a fixed boundary misorientation to determine their effects on void nucleation and coalescence. Samples were soft recovered and cross-sectioned to characterize damage using electron backscattering diffraction and scanning electron microscopy to gather information on damage characteristics at and around the GB, with emphasis on growth of boundary and bulk voids. Chemistry and composition analysis were also performed on samples to determine if trace elements present in a sample affected the threshold for void nucleation. Results show that the kinetics of damage growth at the boundary are strongly affected by stress level and impurities. It was found that the boundary selected had a similar or even lower tendency to show damage than the bulk at low pulse durations and amplitudes. As pulse duration and amplitude increased damage localized at the boundary, which was found to consist of many small voids, indicating that the boundary experienced rapid void nucleation and coalescence. Furthermore, the presence of impurities correlated strongly with scatter on damage evolution.

36 MATERIALS SCIENCE↗
DOE OSTI2021

Single-Particle Studies Reveal a Nanoscale Mechanism for Elastic, Bright, and Repeatable ZnS:Mn Mechanoluminescence in a Low-Pressure Regime

Mechanoluminescent materials, which emit light in response to elastic deformation, are demanded for use as in situ stress sensors. ZnS doped with Mn is known to exhibit one of the lowest reported thresholds for appearance of mechanoluminescence, with repeatable light emission under contact pressure <10 MPa. Here, the physical basis for such behavior remains as yet unclear. Here, reliable microscopic detection of mechanoluminescence of single ZnS:Mn microparticles, in combination with nanoscale structural characterization, provides evidence that the mechanoluminescent properties of these particles result from interplay between a non-centrosymmetric crystal lattice and its defects, viz., dislocations and stacking faults. Statistical analysis of the distributions of mechanoluminescence energy release trajectories reveals two distinct mechanisms of excitation: one attributable to a piezo-phototronic effect and the other due to dislocation motion. At pressures below 8.1 MPa, both mechanisms contribute to mechanoluminescent output, with a dominant contribution from the piezo-phototronic mechanism. In contrast, above 8.1 MPa, dislocation motion is the primary excitation source. For the piezo-phototronic mechanism, we propose a specific model that accounts for elastic ZnS:Mn mechanoluminescence under very low pressure. The charged interfaces in stacking faults lead to the presence of filled traps, which otherwise would be empty in the absence of the built-in electric field. Upon application of external stress, local enhancement of the piezoelectric field at the stacking faults’ interfaces facilitates release of the trapped carriers and subsequent luminescence. This field enhancement explains how <10 MPa pressure produces thousands of photons.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Linking constituent phase properties to ductility and edge stretchability of two DP 980 steels

Two DP 980 steels were characterized with multiple methods to determine its microstructure characteristics, tensile properties and edge stretchability. The first (DP980-B) is a commercial grade DP980 steel produced by AK Steel, while the second (DP980-T) is a modification of the first one by a tempering process. Both contain two individual phases: ferrite and martensite with body centered cubic (BCC) and tetragonal (BCT) crystal structure respectively. ASTM standard tensile tests were performed for both materials, revealing that DP980-B has higher work hardening and larger total elongation than DP980-T. Standard hole piercing and subsequent hole expansion and extrusion tests were also performed. The critical hole expansion ratio (HER) of hole pierced sheet at different nominal clearances, on the other hand, show an opposite trend: the HER of DP980-T almost doubles that of DP980-B. This indicates the tensile ductility and edge stretchability are determined by different mechanisms due to different deformation modes. The ductility of sheet metal during uniaxial tension is determined by deformation instability, i.e. necking, due to less constraint at the region of deformation and fracture will occur quickly after necking. The contribution of post-necking deformation to the total elongation is insignificant for the high strength grades such as DP980 steels. The ductility during hole-expansion, however, is mainly determined by material fracture behavior that is dependent on phase property disparity and material intrinsic fracture parameters. With the individual phase properties for both DP steels determined by in situ tensile tests under high energy X-ray diffraction, the results show that DP980-T steel has lower property disparities between the two phases than DP980-B steel, due to the tempering process. This explains why the DP980-T steel has higher HER than DP980-B steel: lower phase disparity will lead to less local deformation during loading. The higher work hardening rate for DP980-B steel contributes to its higher uniform elongation compared with DP980-T steel based on the maximum load condition of deformation instability. An integrated finite element simulation framework for studying hole expansion is also presented here, based on the calculated individual phase properties from the combined high energy x-ray diffraction (HEXRD) and elastic plastic self-consistent modeling. The simulation results correlate well with the experimental results on the HER difference between the two materials.

36 MATERIALS SCIENCE↗
DOE OSTI2020

An Integrated Multiscale Experimental-Numerical Analysis on Reconsolidation of Salt-Clay Mixture for Disposal of Heat-Generating Waste (Final NEUP Technical Report)

The overall purpose of this research is to improve understanding of THMC coupling effect on the reconsolidation of granular (or crushed) salt-clay mixture used for seal systems of shafts and drifts in salt repositories. This proposed work is partially motivated by the recent work on the Waste Isolation Pilot Plant (WIPP) that shows the promising sealing capability of clay-salt mixture compared to crushed salt. In particular, primary emphasis is to develop a fully integrated multiscale experiment-numerical study to determine and explain what leads to the superior sealing ability of the clay-salt mixture. These research activities are designed to seek further understanding of (1) why clay additives may enhance the fluid trapping and (2) whether this flow barrier effect may prevail under different combinations of temperature, confining pressure, deviatoric stress and other foreseeable environmental factors. If successful, this enhanced flow trapping ability of the seal provides significant improvement to the seal and repository performance and therefore make the repository safer in the long-term. The experiment component includes microstructural investigation and macroscopic tests on a reconsolidated salt-clay mixture. In the microstructural study, the goal is to (1) characterize microscopic distributions of distinct phases (e.g., clay, salt crystal boundaries, trapped brine, and pore) to examine the connectivity of the pore network inside the salt-clay mixture with different amounts of clay additive and moisture content and (2) analyze multiscale imaging data to reconstruct the polycrystalline microstructures for numerical simulations. Meanwhile, macroscopic tests are performed to analyze how clay alters the failure/creep mechanisms in the salt-clay mixture. Microscopic and macroscopic experimental observations will both be used to calibrate and validate a multiscale model that explicitly simulates the capillary and multiphase flow in the connected pores and the deformation due to the presence of intra-crystalline brine at the pore scale via a new polyhedral discrete element–lattice Boltzmann method (DEM-LBM) coupling model. The pore-scale simulations are homogenized via an upscaling procedure that converts pore-scale information (e.g. force exerted on grain boundary, sliding, pressure-solution) to continuum measures (e.g. Cauchy stress, Darcy’s flow) at each integration point in the macroscopic multiphase TMHC model. This multiscale scheme will allow coupling be- tween high-fidelity simulations of brine-salt-clay interaction and the macroscopic TMHC model. The multiscale model helps the understanding of how the trapped brine inclusion affects the pressure-solution mechanism with the presence of clay and moisture. This work brings new insight into the sealing capacity of salt-clay mixture under elevated temperature over a long period of time - a key to evaluating the potential of salt-clay mixture usage for salt repositories.

42 ENGINEERING↗
DOE OSTI2020

The CLAS12 Forward Tagger

This document presents the technical layout and the performance of the CLAS12 Forward Tagger (FT). The FT, composed of an electromagnetic calorimeter based on PbWO$_4$ crystals (FT-Cal), a scintillation hodoscope (FT-Hodo), and several layers of Micromegas trackers (FT-Trk), has been designed to detect electrons and photons scattered at polar angles from 2$^\circ$ to 5$^\circ$ and to meet the physics goals of the hadron spectroscopy program and other experiments running with the CLAS12 spectrometer in Hall B.

46 INSTRUMENTATION RELATED TO NUCLEAR SCIENCE AND ↗
DOE OSTI2024

Structural and mechanical properties of monolayer amorphous carbon and boron nitride

Amorphous materials exhibit various characteristics that are not featured by crystals and can sometimes be tuned by their degree of disorder (DOD). Here, we report results on the mechanical properties of monolayer amorphous carbon (MAC) and monolayer amorphous boron nitride (maBN) with different DOD. The pertinent structures are obtained by kinetic-Monte-Carlo (kMC) simulations using machine-learning potentials (MLP) with density-functional-theory (DFT)-level accuracy. An intuitive order parameter, namely the areal fraction F x occupied by crystallites within the continuous random network, is proposed to describe the DOD. We find that F x captures the essence of the DOD: Samples with the same F x but different sizes and arrangements of crystallites, obtained using two distinct kMC procedures, have virtually identical radial distributions functions as well as bond-length and bond-angle distributions. Furthermore, by simulating the fracture process with molecular dynamics, we found that the mechanical responses of MAC and maBN before fracture are mainly determined by F x and are insensitive to the sizes and specific arrangements and to some extent the numbers and area distributions of the crystallites. The behavior of cracks in the two materials is analyzed and found to mainly propagate in meandering paths in the CRN region and to be influenced by crystallites in distinct ways that toughen the material. Furthermore, the present results reveal the relation between structure and mechanical properties in amorphous monolayers and may provide a universal toughening strategy for 2D materials.

2-dimensional systems↗
NASA NTRSDate not supplied

Initial analysis of “stone” size Ryugu samples: current status

As a part of the initial analysis of the Ryugu samples, we perform a variety of analyses of millimeter-sized "stones". Our goals are to elucidate the entire formation process of C-type asteroid Ryugu from the viewpoint of petrology and mineralogy ande obtain necessary information by sample analysis, and then simulate the formation of Ryugu based on the evidencef obtained rom sample analysis. Eighteen stones (8 from Room A and 10 from Room C) were received from the ISAS curation facility on June 1, 2021, and brought into a fully nitrogen-displaced glove box at Tohoku University. At the same time, we also received the powder samples from Room A and Room C. To completely block the atmosphere from leaking into the container, all samples were put in the sample transport containers prepared by ISAS, transferred from the main chamber to the glovebox at ISAS, and then all containers were completely sealed in plastic bags with moisture and oxygen absorbers. No moisture or oxygen was detected when the bags were opened in the glove box at Tohoku University, so it was confirmed that there was no exposure to the atmosphere during transport. To date, a number of analyses have been carried out successfully and almost on schedule. The analysis started with the measurement of reflectance spectra, which are sensitive to atmospheric oxidation, hydroxylation, and adsorbed water. The visible, near-infrared, and mid-infrared reflectance spectra were measured while the samples were kept airtight. The spectra of powder samples and stone samples (as aggregates and as single stone) were successfully obtained. A major feature of the stone team's analysis is the use of synchrotron radiation facilities around the world. Since this analysis is non-destructive, stone samples whose reflectance spectra were measured were sent to KEK, SPring-8, ESRF (France), SOLEIL (France), DESY (Germany), and APS (USA). Using these synchrotron radiation facilities, high spatial resolution and sensitivity XRD, STXM, XANES, CT [1], IR-CT, FT-IR [2, 3], XRF, and Mössbauer analyses were performed. Most of the analyses were carried out under air-tight conditions on the stone samples and the particulates separated from the stone samples. These analyses allowed us to determine the three-dimensional distribution of minerals and elements, redox state, density and porosity of the stone samples. Furthermore, as a characteristic analysis of the stone team, light elemental analysis using negative Muon was performed at the MLF facility of J-PARC with an exceptionally long allocation of machine time. This is the only non-destructive method to measure the concentration of light elements in the whole (not the surface) of stone samples. Because the characteristic X-rays produced by muon irradiation are much higher in energy than the fluorescent X-rays produced by X-ray irradiation, there is little effect of self-absorption by the sample, and therefore, the concentration of light elements such as carbon, oxygen, and Na in the entire "stone" sample can be determined. Some stone samples are currently being measured for heat and strength physical properties in order to understand the physical properties of asteroid Ryugu. The data obtained from these measurements are useful for interpreting the remote-sensing data data taken from the surface layer of the asteroid Ryugu [4-7]. It is also important for understanding the behavior of the Ryugu material during impact events. The surfaces of many stone samples were observed by electron microscopy and other techniques, especially on natural “flat” surfaces formed on 5 stomes. As a result, characteristric mineral aggregates formed by the reactions with water and characteiristic impact features were observed on some of the samples. Based on the observations of surfaces and the synchrotron measurements of the whole stones, important objects such as characteristic structures and specific crystal aggregates for understanding the formation history of the asteroid were identified, and these parts were separated from the stone samples using an Xe beam (pFIB) and analyzed by various methods including transmission electron microscopy and synchrotron radiation analysis. Many stone samples, from which important objects have been separated, are embedded in epoxy resin and cut to produce many polished sections. Electron microscopy and spectroscopic measurements of the polished surfaces are being carried out to reveal the detailed mineralogical properties and elemental distribution inside the stone samples. In the fall, machine time for synchrotron radiation will begin, and we plan to analyze single crystals and characteristic objects separated from the stone samples.

Tomoki Nakamura↗