SEARCH · Engineering Papers

Results for “plastic behavior”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

NASA NTRS1980

Influence of stress interaction on the behavior of off-axis unidirectional composites

The yield function for plane stress of a transversely isotropic composite lamina consisting of stiff, linearly elastic fibers and a von Mises matrix material is formulated in terms of Hill's elastic stress concentration factors and a single plastic constraint parameter. The above are subsequently evaluated on the basis of observed average lamina and constituent response for the Avco 5505 boron epoxy system. It is shown that inclusion of residual stresses in the yield function together with the incorporation of Dubey and Hillier's concept of generalized yield stress for anisotropic media in the constitutive equation correctly predicts the trends observed in experiments. The incorporation of the strong axial stress interaction necessary to predict the correct trends in the shear response is directly traced to the high residual axial stresses in the matrix induced during fabrication of the composite.

Pindera, M. J.↗

NASA NTRS1994

Review of modelling small-crack behavior and fatigue-life predictions for aluminum alloys

The small-crack effect, where small fatigue cracks grow faster and at lower stress-intensity factors than large cracks, has been found to be significant for many materials and loading conditions. In this paper, plasticity effects and crack-closure modelling of small fatigue cracks are reviewed. A crack-closure model with a cyclic-plastic-zone-corrected effective stress-intensity factor range (related to the cyclic J-integral) and microstructural data on crack-initiation sites were used to calculate small-crack growth rates and fatigue lives for unnotched and notched specimens made of two aluminum alloys. The crack-closure transient from the plastic wake was shown to be the dominant cause of the small-crack effect and plasticity effects on the cyclic-plastic-zone-corrected stress-intensity factor range were negligible except at extremely high stress levels. Small-crack growth rates and fatigue lives under both constant-amplitude and spectrum loading from tests and analyses agreed well.

CRACK CLOSURE MODELLING↗

NASA NTRS1994

A Review Of Modelling Small-Crack Behavior And Fatigue-Life Predictions For Aluminum Alloys

The small-crack effect, where small fatigue cracks grow faster and at lower stress-intensity factors than large cracks, has been found to be significant for many materials and loading conditions. In this paper, plasticity effects and crack-closure modelling of small fatigue cracks are reviewed. A crack-closure model with a cyclic-plastic zone-corrected effective stress-intensity factor range (related to the cyclic J-integral) and microstructural data on crack-initiation sites were used to calculate small-crack growth rates and fatigue lives for unnotched and notched specimens made of two aluminum alloys. The crack-closure transient from the plastic wake was shown to be the dominant cause of the small-crack effect and plasticity effects on the cyclic-plastic zone-corrected stress-intensity factor range were negligible except at extremely high stress levels. Small-crack growth rates and fatigue lives under both constant-amplitude and spectrum loading from tests and analyses agreed well.

Newman, J. C., Jr.↗

NASA NTRS2014

Crack Growth Behavior in the Threshold Region for High Cycle Fatigue Loading

This paper describes the results of a research program conducted to improve the understanding of fatigue crack growth rate behavior in the threshold growth rate region and to answer a question on the validity of threshold region test data. The validity question relates to the view held by some experimentalists that using the ASTM load shedding test method does not produce valid threshold test results and material properties. The question involves the fanning behavior observed in threshold region of da/dN plots for some materials in which the low R-ratio data fans out from the high R-ratio data. This fanning behavior or elevation of threshold values in the low R-ratio tests is generally assumed to be caused by an increase in crack closure in the low R-ratio tests. Also, the increase in crack closure is assumed by some experimentalists to result from using the ASTM load shedding test procedure. The belief is that this procedure induces load history effects which cause remote closure from plasticity and/or roughness changes in the surface morphology. However, experimental studies performed by the authors have shown that the increase in crack closure is a result of extensive crack tip bifurcations that can occur in some materials, particularly in aluminum alloys, when the crack tip cyclic yield zone size becomes less than the grain size of the alloy. This behavior is related to the high stacking fault energy (SFE) property of aluminum alloys which results in easier slip characteristics. Therefore, the fanning behavior which occurs in aluminum alloys is a function of intrinsic dislocation property of the alloy, and therefore, the fanned data does represent the true threshold properties of the material. However, for the corrosion sensitive steel alloys tested in laboratory air, the occurrence of fanning results from fretting corrosion at the crack tips, and these results should not be considered to be representative of valid threshold properties because the fanning is eliminated when testing is performed in dry air.

Forman, R. G.↗

DOE OSTI2022

Laboratory Accelerated Cyclic Corrosion Testing and On-Road Corrosion Testing of AA6××× Coupled to Carbon Fiber-Reinforced Plastics

Structures made from a combination of aluminum alloy (AA) and carbon fiber-reinforced plastic (CFRP) are susceptible to galvanic corrosion of the AA in harsh atmospheric conditions, such as might exist for closure panels in automotive applications. It is important to understand the galvanic corrosion behavior of these materials under laboratory conditions as that might allow prediction of performance in real environments. This work tested specially designed AA6×××-CFRP coupons, including AA6111 and AA6022, connected to CFRP made from two different carbon fiber fabrics (twill and random) with the aim of understanding the corrosion behaviors in a laboratory cyclic exposure chamber and during on-road exposure. The extent of corrosion was assessed by galvanic current measurements, optical profilometry, cross-sectional area analysis, and microscopic analysis. Based on the results, it was determined that the corrosion susceptibilities and morphologies observed in CFRP/AA couples tested in an environmental chamber for 12 weeks were in correspondence with those of the coupons subjected to on-road testing for 1 y in Columbus, OH.

Materials Science↗

DOE OSTI2023

Mechanical properties of an Al 10 Nb 20 Ta 15 Ti 30 V 5 Zr 20 A2/B2 refractory superalloy and its constituent phases

Refractory superalloys (RSAs) are a new class of high-temperature structural materials consisting of a nanometer-sized mixture of two coherent A2 (disordered BCC) and B2 (ordered) phases. While these RSAs typically exhibit superior mechanical properties at elevated temperatures, they suffer from limited plasticity at lower temperatures, often attributed to the continuous ordered B2 matrix in these two-phase alloys. To knowledgably control the microstructure and mechanical properties of these alloys, the properties of the constitutive phases in RSAs should be known. Currently this information is absent. Here, in the present work, the microstructure and mechanical properties (at 20–1200 °C) of a candidate Al 0.5 NbTa 0.8 Ti 1.5 V 0.2 Zr RSA and two single-phase alloys, which compositions correspond to the compositions of the A2 and B2 phases in the selected RSA, are reported. Interestingly, and quite unexpectedly, the intrinsic mechanical behavior of the constituent A2 and B2 phases, deciphered for the first time in the present study, revealed that they are softer and substantially more ductile than the parent two-phase RSA. Furthermore, the ordered B2 phase exhibits a deformation twinning mechanism leading to twinning induced plasticity (TWIP) coupled with a low APB energy and activity of 1/2<111> dislocations. These mechanisms are thought to be responsible for the high plasticity of the ordered B2 phase. The results presented here question the current assumption that the ordered B2 phase in these RSAs has limited plasticity and strongly indicate that the nature of the B2/A2 interface boundaries and coherency strengthening play an important role in controlling the mechanical properties of the two-phase RSA.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Investigation of pressure-controlled injection molding on the mechanical properties and embodied energy of recycled high-density polyethylene

Manufacturing with secondary feedstock has been identified as an effective strategy to improve plastic circularity. However, product quality inconsistencies arise due to variations in molecular weight, rheology, and mechanical properties. This work evaluates the processing of recycled high-density polyethylene using pressure-controlled injection molding with a focus on processing behavior and energy consumption. Further, the effects of injection velocity, packing pressure, and transfer position are benchmarked against a conventional velocity-controlled process. The experimental results show that the novel process control strategy significantly affects the mechanical properties, in-mold rheology, and energy consumption. Parts fabricated using pressure-controlled injection molding showed higher tensile properties due to increased macromolecular orientation. Additionally, reduced energy was used due to lower melt pressures required to completely replicate the cavity geometry. The results demonstrate the potential of the technology to support increased utilization of secondary feedstock and reduced carbon footprint.

36 MATERIALS SCIENCE↗

DOE OSTI2023

A mesoscale crystal plasticity model to predict room-temperature deformation and martensitic transformation of high-strength Quenching and Partitioning (Q&P) Steels and validation with synchrotron X-ray diffraction

Renowned for the superior mechanical properties and adeptness at cold-forming, Quenching and Partitioning (QP) steels have gained prominence as a promising candidate material in fabricating safety-critical components in various industries. The pertinent research on QP steels focus on the martensitic transformation of the Retained Austenite (RA) phase during cold-forming, a crucial mechanism that substantially influences the overall strength and ductility of QP steels. The austenite stability and transformation rate heavily rely on the local strain path and the initial microstructure, which is challenging for analytical prediction. In this paper, a mesoscale model is developed to capture the deformation and transformation kinetics of QP steels inside the microstructure. The model integrates the detailed explicit microstructure, acquired from characterization experiments, into a high-resolution finite element (FE) mesh. It distinctly model the deformation and interaction between the various phases and the effect on the transformation of RA. The model is validated with high energy X-ray diffraction (HEXRD) data, and shows excellent capability in predicting the asymmetric stress-strain behavior under uniaxial tension and compression, as well as the martensitic transformation rate. The model is used to investigate the strain and load partitioning effect of surrounding matrix to the transformation of RA, offering insights into the complex behavior of QP980 and facilitates further material development.

36 MATERIALS SCIENCE↗

DOE OSTI2023

Robust deep learning framework for constitutive relations modeling

Modeling the full-range deformation behaviors of materials under complex loading and materials conditions is a significant challenge for constitutive relations (CRs) modeling. Here, we propose a general encoder-decoder deep learning framework that can model high-dimensional stress-strain data and complex loading histories with robustness and universal capability. The framework employs an encoder to project high-dimensional input information (e.g., loading history, loading conditions, and materials information) to a lower-dimensional hidden space and a decoder to map the hidden representation to the stress of interest. We evaluated various encoder architectures, including gated recurrent unit (GRU), GRU with attention, temporal convolutional network (TCN), and the Transformer encoder, on two complex stress-strain datasets that were designed to include a wide range of complex loading histories and loading conditions. All architectures achieved excellent test results with an root-mean-square error (RMSE) below 1 MPa. Additionally, we analyzed the capability of the different architectures to make predictions on out-of-domain applications, with an uncertainty estimation based on deep ensembles. The proposed approach provides a robust alternative to empirical/semi-empirical models for CRs modeling, offering the potential for more accurate and efficient materials design and optimization.

36 MATERIALS SCIENCE↗

NASA NTRS1945

Calculation of Centrally Loaded Thin-Walled Columns Above the Buckling Limit

When thin-walled columns formed from flanged sheet, such as used in airplane construction, are subjected to axial load, their behavior at failure varies according to the slenderness ratio. On long columns the axis deflects laterally while the cross section form is maintained; buckling results. The respective breaking load in the elastic range is computed by Euler's formula and for the plastic range by the Engesser- Karman formula. Its magnitude is essentially dependent upon the length. On intermediate length columns, especially where open sections are concerned, the cross section is distorted while the cross section form is preserved; twisting failure results. The buckling load in twisting is calculated according to Wagner and Kappus. On short columns the straight walls of low-bending resistance that form the column are deflected at the same time that the cross section form changes - buckling occurs without immediate failure. Then the buckling load of the total section computable from the buckling loads of the section walls is not the ultimate load; quite often, especially on thin-walled sections, it lies considerably higher and is secured by tests. Both loads, the buckling and the ultimate load are only in a small measure dependent upon length. The present report is an attempt to theoretically investigate the behavior of such short, thin-walled columns above the buckling load with the conventional calculating methods.

Reinitzhuber, F.↗

DOE OSTI2022

Tuning Stoichiometry to Promote Formation of Binary Colloidal Superlattices

The self-assembly of binary nanoparticle superlattices from colloidal mixtures is a promising method for the fabrication of complex colloidal cocrystal structures. However, binary mixtures often form amorphous or metastable phases instead of the thermodynamically stable phase. Here we show that in binary mixtures of differently sized spherical particles, an excess of the smaller component can promote—and, in some cases, may be necessary for—the self-assembly of a binary cocrystal. Using computer simulations, we identify two mechanisms responsible for this phenomenon. First, excess small particles act like plasticizers and enable systems to reach a greater supersaturation before kinetic arrest occurs. Second, they can disfavor competing structures that may interfere with the growth of the target structure. We find the phase behavior of simulated mixtures of nearly hard spheres closely matches published experimental results. We demonstrate the generality of our findings for mixtures of particles of arbitrary shape by presenting a binary mixture of hard shapes that only self-assembles with an excess of the smaller component.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗

NASA NTRS1972

Analysis of legged landers for the survivable soft landing of instrument payloads.

Two methods of analysis have been developed for legged planetary landers. The first of these, the Large Displacement Gear Analysis, is a design tool for statically determining the large displacement stroking behavior, energy absorption characteristics, and internal load distributions in a single gear. The second, the Landing Dynamics Analysis, predicts the spatial landing dynamics of a legged lander. Effects of structural flexibility, elastic-plastic gear load characteristics, and soil properties on the loads, motions, and stability of the lander may be determined. Validation of the analytical techniques is accomplished through comparison of predicted results and experimental data obtained during a model test program.

Laurenson, R. M.↗

NASA NTRS2016

NiTi Alloys for Tribological Applications: The Role of In-Situ Nanotechnology

Beginning in 2004, NASA initiated the investigation and development of, Nitinol 60, a nickel-rich and dimensionally stable version of shape memory alloy Nitinol 55, as an alternative to bearing steel. Early investigations showed it to be hard and impervious to aqueous corrosion but the fundamental reasons for these properties were unknown. Shape memory alloys made from equiatomic Ni-Ti are widely known for their unique dimensional instability behavior that can be triggered by thermal and mechanical stress. The nickel-rich alloys exhibit no such dimension change property and have high hardness but have largely been overlooked by industry and the engineering community. Though steel is the dominant material of choice for mechanical components (bearings and gears) it has intrinsic limitations related to corrosion and plastic deformation. In contrast, Ni-Ti alloys are intrinsically rustproof and can withstand high contact loads without damage (denting). Over the last decade, focused RD to exploit these alloys for new applications has revealed that in-situ nano-scale phases that form during processing are largely responsible for NiTis remarkable properties. In this presentation, the state-of-art of nickel-rich NiTi alloys will be introduced and the nanotechnology behind their intriguing behavior will be addressed. The presentation will include discussion of how NASA is adopting this new technology inside the space station water recycling system as a pathfinder for more down-to-earth tribological challenges.

metals↗

DOE OSTI2021

Thermal-Mechanical Elastic-Plastic and Ductile Failure Model Calibrations for 304L Stainless Steel Alloy

Numerical simulations of metallic structures undergoing rapid loading into the plastic range require material models that accurately represent the response. In general, the material response can be seen as having four interrelated parts: the baseline response under slow loading, the effect of strain rate, the conversion of plastic work into heat and the effect of temperature. In essence, the material behaves in a thermal-mechanical manner if the loading is fast enough so when heat is generated by plastic deformation it raises the temperature and therefore influences the mechanical response. In these cases, appropriate models that can capture the aspects listed above are necessary. The material of interest here is 304L stainless steel, and the objective of this work is to calibrate thermal-mechanical models: one for the constitutive behavior and another for failure. The work was accomplished by first designing and conducting a material test program to provide data for the calibration of the models. The test program included uniaxial tension tests conducted at room temperature, 150 and 300 C and at strain rates between 10 –4 and 10 3 1/s. It also included notched tension and shear-dominated compression hat tests specifically designed to calibrate the failure model. All test specimens were extracted from a single piece of plate to maintain consistency. The constitutive model adopted was a modular $J_2$ plasticity model with isotropic hardening that included rate and temperature dependence. A criterion for failure initiation based on a critical value of equivalent plastic strain fitted the failure data appropriately and was adopted. Possible ranges of the values of the parameters of the models were determined partially on historical data from calibrations of the same alloy from other lots and are given here. The calibration of the parameters of the models were based on finite element simulations of the various material tests using relatively ne meshes and hexahedral elements. When using the model in structural finite element calculations, however, element formulations and sizes different from those in the calibration are likely to be used. A brief investigation demonstrated that the failure initiation predictions can be particularly sensitive to the element selection and provided an initial guide to compensate for the effect of element size in a specific example.

36 MATERIALS SCIENCE↗

DOE OSTI2022

In-situ synchrotron X-ray diffraction investigation on deformation behavior of Nb/NiTi composite during pre-straining process

The mechanisms responsible for deformation behavior in Nb/NiTi composite during pre-straining were investigated systematically using in-situ synchrotron X-ray diffraction, transmission electron microscopy and tensile test. It is shown that upon loading, the composite experiences elastic elongation and slight plastic deformation of B19', B2 and β-Nb phases, together with the forward stress-induced martensitic (SIM) transformation from B2 to B19'. Upon unloading, the deformation mechanisms of the composite mainly involve elastic recovery of B19', B2 and β-Nb phases, compression deformation of β-Nb phase and incomplete B19'→B2 reverse SIM transformation. In the tensile loading-unloading procedure, besides the inherent elastic deformation and SIM transformation, the (001) compound twins in B19' martensite can also be conducive to the elastic deformation occurring in B19'-phase of the composite. Therefore, this composite can exhibit a large recoverable strain after unloading owing to the elastic deformation, and the partially reversible and consecutive SIM transformation together with the (001) compound twins.

36 MATERIALS SCIENCE↗

DOE OSTI2022

Experimental study of compaction localization in carbonate rock and constitutive modeling of mechanical anisotropy

Abstract Sedimentary rocks are inherently anisotropic and prone to strain localization. While the influence of rock anisotropy on the brittle/dilative regime has been studied extensively, its influence on the ductile/compactive regime is much less explored. This paper discusses the anisotropic behavior of a high‐porosity carbonate rock from central Europe (the Maastricht Tuffeau). A set of triaxial tests with concurrent x‐ray tomography has been performed at different confining pressures. The anisotropic characteristics of this rock have been investigated by testing samples cored at different inclinations of the bedding, thus revealing non‐negligible effects of the coring direction on yielding and compaction behavior. Specifically, samples cored perpendicular to bedding display higher strength and longer stages of post‐yielding deformation before manifesting re‐hardening. Despite such alterations of the inelastic response, Digital Image Correlation has revealed that the strain localization mode is independent of the coring direction, thus being primarily affected by the confinement level. To capture the observed interaction between material anisotropy and compaction behavior at the continuum‐scale, an elastoplastic constitutive law has been proposed. For this purpose, a set of tensorial bases has been introduced to replicate how the oriented rock fabric modulates the yielding and plastic flow characteristics of the material. The analyses show that the impact of the coring direction on yield function and plastic flow rule is fundamentally different, thus requiring the use of distinct projection strategies (a strategy here defined heterotopic mapping). The performance of the model, studied through parametric analyses and by calibrating the experimental results, illustrates the improved capability of the proposed constitutive approach when applied to strongly anisotropic porous rocks.

Shahin, Ghassan↗

DOE OSTI2021

Rheology of fresh cement pastes containing polymer nanoparticles

Influences of polymer nanoparticles (PNPs) with varied charge densities on the rheological behaviors of fresh cement pastes (fcps) without and with polycarboxylate superplasticizer (PCE) were studied. In the blank fcp, the addition of PCE and highly anionically charged PNPs greatly decreases the yield stress and the plastic viscosity due to their large adsorption on cement that produces electrostatic repulsion and steric hindrance between cement grains. However, the non-adsorbing nonionic PNPs show a slightly opposite effect. In the PCE-containing fcp, both the anionic and nonionic PNPs become non-adsorbing on cement due to the stronger affinity of PCE to cement surface. In this way, the addition of the PNPs in the PCE-containing fcp slightly increases the yield stress and the plastic viscosity, but significantly decreases the pseudoplastic index, which is believed to result from the generation of the so-called depletion attractive force between cement grains induced by the non-adsorbing polymers.

36 MATERIALS SCIENCE↗

DOE OSTI2026

Consolidation and Permeability of the B1 and D1 Gas Hydrate Bearing Sands and Associated Seal Sediments of the Extended-Duration Gas Production Test Site on the Alaska North Slope

Gas hydrate, a solid combination of gas (mostly methane in nature) and water molecules stable at low temperatures and elevated pressures, occurs naturally in marine and permafrost-associated environments. Gas hydrate reservoirs, such as those in the Alaska North Slope, have been considered potential energy resources for gas production. To understand the petrophysical and geo-mechanical characteristics of the reservoir, core samples retrieved from the site of the JOGMEC-DOE-USGS collaborative gas hydrate R&D project have been analyzed in the laboratory for their hydraulic and mechanical properties. This paper focuses on both seal and reservoir samples associated with the B1 and D1 sands, which are evaluated for index properties (including porosity, grain size distribution, liquid and plastic limits, specific surface area, and specific gravity), consolidation, permeability, and water retention. Furthermore, the reservoir core samples were tested with pore-filling, laboratory-grown tetrahydrofuran hydrate, in order to assess reservoir behavior during gas production from hydrates. Under simulated in situ stress conditions, the seal and hydrate-free reservoir cores had a permeability anisotropy ratio of k h /k v = 3.0−5.0, and k h /k v = 2.4−3.0 for the reservoir tetrahydrofuran hydrate-bearing cores. The data suggest that depressurizing the reservoir to induce hydrate dissociation alters the reservoir effective permeability in three ways: permeabilities decrease due to porosity lost (e.g., the initial reservoir thickness can decrease by up to 5% upon 7 MPa depressurization), permeability increases due to the loss of solid hydrate in the pore space, and permeability anisotropy k h /k v decreases in response to the evolving pore-space geometry. We show that given the simulated in situ gas hydrate saturations (i.e., S h = 32% in core 7P-2E and S h = 21% in core 20P-4), gas production from the dissociation of tetrahydrofuran hydrate in the two tested cores results in a net increase in effective permeability and a decrease in k h /k v . This study highlights the importance of investigating seal and reservoir sediments and the impacts of depressurization on the porosity and permeability responses during production.

Geological materials↗