Results for “performance data” — Page 43

NASA NTRS2006

Comanche Helmet-Mounted Display Symbology Simulation

The Aeroflightdynamics Directorate (AMRDEC) conducted a simulation to examine the performance of the Comanche Contact Analog world-referenced symbology displayed on the Comanche HIDSS when compared with a compressed symbology design similar to that specified by the former MIL-STD 1295. Six experimental test pilots flew one modified ADS-33 maneuver (hover turn, bob-up), an unusual attitude recovery, and two terrain flight tactical tasks in the NASA Vertical Motion Simulator (VMS). Analysis of the pilot objective performance data and subjective data showed the following results. Objective test results showed that 1295 symbology yielded more rapid maneuvering in the hover turn bob-up than Contact Analog symbology. The average margin of difference in the time to complete the maneuver was approximately two seconds, which was statistically significant. There were no significant differences measured between symbology sets with respect to altitude or position performance measures for all other maneuvers. The NOE target ID task data showed improved accuracy in determining heading to target when using Contact Analog over MIL-STD-1295. Subjective test results, including handling qualities ratings (HQRs) and NASA-TLX workload ratings, showed small but consistent advantages of 1295 symbology over Contact Analog for most parameters. For the bob-up maneuver, 1295 symbology handling qualities were rated Desired for lateral position error and time to complete whereas Contact Analog was rated adequate. The average HQRs for all other maneuvers were rated the same for both symbology sets. Pilot comments and the results of an online questionnaire more strongly favored 1295 over Contact Analog. Repeated comments from all six pilots led to a focus on design issues with six Contact Analog symbols. Those symbols were the heading tape, horizon line, radar altitude six-second predictor, the position of the torque symbol, the absence of a hover position cue, and the widespread positioning of the symbology to the outer edges of the display field-of-view. Pilots rated the present design of three of the six symbols as having safety-of-flight implications. Those symbols were the heading tape, horizon line, and six-second predictor. To summarize, test results showed no objective data that would warrant restricting experimental test pilots from flying constrained tasks. Small but consistent advantages were recorded for the MILSTD-1295 symbology design when executing ADS-33 constrained tasks. No general performance differences were recorded for the operational maneuvers (NOE, contour flight modes) except for the azimuth-to-target task, which favored the Contact Analog heading tape design. There were consistent and strong pilot comments supporting the MIL-STD-1295 design over Contact Analog in both this current simulation and in Comanche Sim I. Three Contact Analog symbols warrant modification and further evaluation to mitigate safety-of-flight implications noted by participating test pilots. A plan for symbology redesign and testing was developed. However, the Comanche program was cancelled by Department of Army in February 2004.

Turpin, Terry S.↗

NASA NTRS2010

Human Habitation in a Lunar Electric Rover During a 14-Day Field Trial

Various military and commercial entities, as well as the National Aeronautics and Space Administration (NASA), have conducted space cabin confinement studies. However, after an extensive literature search, only one study was found using a simulated lunar rover (LUNEX II), under laboratory conditions, with a crew of two for an eighteen day lunar mission. Forty-three years later, NASA human factors engineers conducted a similar study using the Lunar Electric Rover (LER) in a dynamic real-world lunar simulation at the Black Point Lava Flow in Arizona. The objective of the study was to obtain human-in-the-loop performance data on the vehicle s interior volume with respect to human-system interfaces, crew accommodations, and habitation over a 14-day mission. Though part of a larger study including 212 overall operational elements, this paper will discuss only the performance of fifty different daily habitational elements within the confines of the vehicle carried out by two male subjects. Objective timing data and subjective questionnaire data were collected. Results indicate, much like the LUNEX II study, the LER field study suggest that a crew of two was able to maintain a satisfactory performance of tasks throughout the 14-day field trail within a relative small vehicle volume.

Litaker, Harry, Jr.↗

DOE OSTI2022

NREL Fleet Analysis Support Through Technology Integration Collaboration

This study leveraged the partnership between the United States Department of Energy's (DOE) Clean Cities Coalition Network and the Association for the Work Truck Industry (NTEA) to launch a vehicle and fleet analysis project that assisted fleets in identifying opportunities to save energy, improve efficiency, reduce costs, and meet environmental goals via short term data logging and analysis. The National Renewable Energy Laboratory (NREL) sought to establish a process that included initial data acquisition, provided data storage, and developed analytic methods to inform fleets of areas of opportunity based on approximately 30 days of in use vehicle performance data. However, long-term the project will require ongoing funding to fully develop and maintain the data sharing platform and to produce more complex analysis.

33 ADVANCED PROPULSION SYSTEMS↗

NASA NTRS1979

A simulation investigation of cockpit display of aircraft traffic during curved, descending, decelerating approaches

The results of a simulation experiment involving the evaluation of cockpit display of aircraft traffic information are presented. The experiment was conducted using taped time dependent, noninteractive traffic in an approach to landing situation and two levels of pilot control models: 3-D automatic and computer augmented control. The tests involved two cases: the simulation aircraft flew approach paths which (1) followed another aircraft in between two other aircraft, and (2) merged between two other aircraft. Speed control via manual throttles was used in all tests (path stretching was not allowed for maintaining separation between aircraft). The approaches were conducted while the simulation aircraft was conducting a curved, descending, decelerating approach to landing. Performance data sets were examined, and subjective opinions regarding workload were gathered. Traffic positioning was varied to further evaluate the test subjects' monitoring performance.

Steinmetz, G. G.↗

NASA NTRS1987

Martian Clouds Data Workshop

The major topics covered were a discussion of the structure of relational data base systems and features of the Britton Lee Relational Data Base Management System (RDBMS); a discussion of the workshop's objectives, approach, and research scenarios; and an overview of the Atmospheres Node User's Guide, which details the datasets stored on the Britton Lee, the structure of the query and data analysis system, and examples of the exact menu screens encountered. Also discussed were experience with the system, review of the system performance, and a strategy to produce queries and performance data retrievals of mutual interest. The goals were defined as examining correlations between cloud occurrence, water vapor abundance, and surface properties.

Lee, Steven↗

NASA NTRS1992

Supersonic investigation of two dimensional hypersonic exhaust nozzles

An experimental investigation was conducted in the NASA Lewis 10 x 10 ft supersonic Wind Tunnel to determine the performance characteristics of 2D hypersonic exhaust nozzles/afterbodies at low supersonic conditions. Generally, this type of application requires a single expansion ramp nozzle (SERN) that is highly integrated with the airframe of the hypersonic vehicle. At design conditions (hypersonic speeds), the nozzle generally exhibits acceptable performance. At off-design conditions (transonic to mid-supersonic speeds), nozzle performance of a fixed geometry configuration is generally poor. Various 2-D nozzle configurations were tested at off-design conditions from Mach 2.0 to 3.5. Performance data is presented at nozzle pressure ratios from 1 to 35. Jet exhaust was simulated with high-pressure air. To study performance of different geometries, nozzle configurations were varied by interchanging the following model parts: internal upstream contour, expansion ramp, sidewalls, and cowl.

Carboni, Jeanne D.↗

NASA NTRS1993

The Third NASA Goddard Conference on Mass Storage Systems and Technologies

This report contains copies of nearly all of the technical papers and viewgraphs presented at the Goddard Conference on Mass Storage Systems and Technologies held in October 1993. The conference served as an informational exchange forum for topics primarily relating to the ingestion and management of massive amounts of data and the attendant problems involved. Discussion topics include the necessary use of computers in the solution of today's infinitely complex problems, the need for greatly increased storage densities in both optical and magnetic recording media, currently popular storage media and magnetic media storage risk factors, data archiving standards including a talk on the current status of the IEEE Storage Systems Reference Model (RM). Additional topics addressed System performance, data storage system concepts, communications technologies, data distribution systems, data compression, and error detection and correction.

Kobler, Benjamin↗

NASA NTRS1995

High performance nickel electrodes for space power applications

The specific energy density and the performance of nickel electrodes are generally limited by the electrode microstructure and the nature of the active material within the electrode matrix. Progress is being made in our laboratory in a collaborative effort with NASA-LEWIS Research Center to develop lighter weight, mechanically stable and highly efficient nickel electrodes for aerospace applications. Our approach is based on an electrode microstructure fabricated from a mixture of nickel fibers as small as 2 micro m diameter and cellulose fibers. Results will be presented to show the optimum conditions for impregnating this electrode microstructure with nickel hydroxide active material. Performance data in half-cell tests and cycle life data will also be presented. The flexibility of this electrode microstructure and the significant advantages it offers in terms of weight and performance will be demonstrated, in particular its ability to accept charge at high rates and to discharge at high rates.

Adanuvor, Prosper K.↗

NASA NTRS2002

Performance Study and CFD Predictions of a Ducted Fan System

An experimental investigation was completed in the NASA Ames 7 by 10-Foot Wind Tunnel to study the performance characteristics of a ducted fan. The goal of this effort is to study the effect of ducted fan geometry and utilize Computational Fluid Dynamics (CFD) analysis to provide a baseline for correlation. A 38-inch diameter, 10-inch chord duct with a five-bladed fixed-pitch fan was tested. Duct performance data were obtained in hover, vertical climb, and forward flight test conditions. This paper will present a description of the test, duct performance results and correlation with CFD predictions.

Abrego, Anita I.↗

NASA NTRS2003

Test of Hydrogen-Oxygen PEM Fuel Cell Stack at NASA Glenn Research Center

This paper describes performance characterization tests of a 64 cell hydrogen oxygen PEM fuel cell stack at NASA Glenn Research Center in February 2003. The tests were part of NASA's ongoing effort to develop a regenerative fuel cell for aerospace energy storage applications. The purpose of the tests was to verify capability of this stack to operate within a regenerative fuel cell, and to compare performance with earlier test results recorded by the stack developer. Test results obtained include polarization performance of the stack at 50 and 100 psig system pressure, and a steady state endurance run at 100 psig. A maximum power output of 4.8 kWe was observed during polarization runs, and the stack sustained a steady power output of 4.0 kWe during the endurance run. The performance data obtained from these tests compare reasonably close to the stack developer's results although some additional spread between best to worst performing cell voltages was observed. Throughout the tests, the stack demonstrated the consistent performance and repeatable behavior required for regenerative fuel cell operation.

Bents, David J.↗

NASA NTRS2020

UAS Integration in the NAS Project: Overview of Flight Test Series 6

The National Aeronautics and Space Administration (NASA) Unmanned Aircraft Systems Integration in the National Airspace System (UAS-NAS) Project has conducted a series of flight test campaigns intended to support the reduction of barriers that prevent unmanned aircraft from flying without the required waivers from the Federal Aviation Administration (FAA). The 2019 Flight Test Series 6 (FT6) campaign furthered this path and supported three test configurations: 1) Radar Characterization, 2) Scripted Encounters and 3) Full Mission. Radar Characterization assessed the performance of Honeywell’s low size, weight, and power (low SWaP) radar system; Scripted Encounters investigated the timing of Detect and Avoid (DAA) alerting thresholds using a Department of Defense (DoD) Group 3 unmanned aircraft system (UAS) equipped with low SWaP sensors and three different live intruder aircraft flown at varying encounter geometries; and Full Mission validated human-in-the-loop simulations by collecting pilot performance data from a ground control station while controlling a live unmanned aircraft on a mission in both virtual and live air traffic controlled airspace. The subject pilot observed a research display that presented DAA advisories to maintain separation from live and virtual aircraft. The test was conducted over a twenty-week period within the R-2508 special use airspace located near Edwards Air Force Base (EAFB), CA. Over 240 encounters were flown during the test series and FT6 proved to be invaluable for the purposes of planning, managing, and executing this type of integrated flight test in both live and virtual environments. Data collected from FT6 was provided to the RTCA Special Committee 228 (SC-228) to help inform the Phase 2 Minimum Operational Performance Standards (MOPS). FT6 was the final test series for the UAS-NAS project that began in 2012. This paper provides an overview of FT6 and its success can be directly attributed to the diligent work of the men and women who supported this effort.

UAS in the NAS↗

NASA NTRS1999

Theory and Modeling in Support of Tether

This final report summarizes the work performed by SAIC's Applied Physics Operation on the modeling and support of Tethered Satellite System missions (TSS-1 and TSS-1R). The SAIC team, known to be Theory and Modeling in Support of Tether (TMST) investigation, was one of the original twelve teams selected in July, 1985 for the first TSS mission. The accomplishments described in this report cover the period December 19, 1985 to September 31, 1999 and are the result of a continuous effort aimed at supporting the TSS missions in the following major areas. During the contract period, the SAIC's TMST investigation acted to: Participate in the planning and the execution on both of the TSS missions; Provide scientific understanding on the issues involved in the electrodynamic tether system operation prior to the TSS missions; Predict ionospheric conditions encountered during the re-flight mission (TSS-lR) based on realtime global ionosounde data; Perform post mission analyses to enhance our understanding on the TSS results. Specifically, we have 1) constructed and improved current collection models and enhanced our understanding on the current-voltage data; 2) investigated the effects of neutral gas in the current collection processes; 3) conducted laboratory experiments to study the discharge phenomena during and after tether-break; and 4) perform numerical simulations to understand data collected by plasma instruments SPES onboard the TSS satellite; Design and produce multi-media CD that highlights TSS mission achievements and convey the knowledge of the tether technology to the general public. Along with discussions of this work, a list of publications and presentations derived from the TMST investigation spanning the reporting period is compiled.

Chang, C. L.↗

NASA NTRSDate not supplied

Earth Independent Medical Operations (EIMO) Datascope: Challenges and Potential Solutions

Data flows and storage/retrieval capacity are severely constrained during missions in space and challenges will become even greater during exploration class missions. There is a need for an artificial intelligence (AI)-based clinical decision support system (CDSS) to monitor and analyze data to provide real-time consultative support for crew medical officer (CMO) decision-making. EIMO is defined as the gradual transition of medical care and decision making from terrestrial to space-based assets, enabling support of astronaut health and performance and reducing overall mission risk. While a hallmark of this paradigm shift from low-earth orbit is that on-board care will increasingly become the responsibility of the astronauts for primary management and decision making, terrestrial assets will continue to be paramount in pre-mission screening and planning, as well as prevention, health maintenance and long-term care contingencies. New capabilities and systems that enable progressively more robust and resilient systems and crews will be necessary to reduce risk and increase probability of deep space exploration mission success. An aspiration for EIMO is to develop AI-enhanced solutions for analysis of crew health & performance data and to facilitate clinical decision support for autonomous medical operations. A “system of systems” approach is envisioned whereby EIMO will deploy AI-supported natural language processing and machine learning (ML) techniques to utilize embedded reference databases and real-time data streams [input vectors] from multiple data sources. Constituent input vectors may include environmental controls, countermeasures data, behavioral data, physiologic wearables, point-of-care laboratory tests, personalized medical records, inventory trade space risk assessments, COTS medical databases, and ground support inputs. An ideal AI capability would possess trained fusion algorithms to cross reference input vectors with medical ‘knowledge’ [cultivated database] to stratify relevant data streams for predictive and actionable capabilities. In addition, EIMO will feature mobility, in that it can be accessed and can push/pull data within and between multiple vehicles/habitats. Large amounts and variable sources of data can be leveraged to diagnose, inform treatment strategies, and potentially predict medical events and performance decrements. Inclusion of advanced training tools using extended reality will enable increasingly autonomous medical care to aid a CMO when ground support is unavailable or time-delayed beyond required action window, e.g., emergent medical situations. EIMO CDSS would require very large datasets to train pre-flight and significant amounts of data are needed to support ML via in-flight CDSS operations. An additional challenge will be to find sufficient data to train a model relevant to astronaut demographics. The rapid, accelerating evolution of this field creates a propitious solution space to leverage multi-modal AI through public-private partnership(s). The status of multi-modal AI systems today would preclude their use for long duration missions as they remain unreliable and are subject to “digital hallucinations” and other errors that could pose operational risk. A federated labs structure is being considered to test and optimize data flow from the multiple input vectors leading to field testing in suitable ground/flight analogs. Critical to the success of an EIMO CDSS will be integration and interoperability and success will be defined by a system that can serve as an in-flight medical consult for the CMO providing critical support during medical contingencies. Benefits to terrestrial medicine may be significant as an outflow of the EIMO medical system, particularly for remote areas and communities lacking significant infrastructure, personnel and resources.

J Lemery↗

NASA NTRS2024

Earth Independent Medical Operations (EIMO) Datascope: Challenges and Potential Solutions

Data flows and storage/retrieval capacity are severely constrained during missions in space and challenges will become even greater during exploration class missions. There is a need for an artificial intelligence (AI)-based clinical decision support system (CDSS) to monitor and analyze data to provide real-time consultative support for crew medical officer (CMO) decision-making. EIMO is defined as the gradual transition of medical care and decision making from terrestrial to space-based assets, enabling support of astronaut health and performance and reducing overall mission risk. While a hallmark of this paradigm shift from low-earth orbit is that on-board care will increasingly become the responsibility of the astronauts for primary management and decision making, terrestrial assets will continue to be paramount in pre-mission screening and planning, as well as prevention, health maintenance and long-term care contingencies. New capabilities and systems that enable progressively more robust and resilient systems and crews will be necessary to reduce risk and increase probability of deep space exploration mission success. An aspiration for EIMO is to develop AI-enhanced solutions for analysis of crew health & performance data and to facilitate clinical decision support for autonomous medical operations. A “system of systems” approach is envisioned whereby EIMO will deploy AI-supported natural language processing and machine learning (ML) techniques to utilize embedded reference databases and real-time data streams [input vectors] from multiple data sources. Constituent input vectors may include environmental controls, countermeasures data, behavioral data, physiologic wearables, point-of-care laboratory tests, personalized medical records, inventory trade space risk assessments, COTS medical databases, and ground support inputs. An ideal AI capability would possess trained fusion algorithms to cross reference input vectors with medical ‘knowledge’ [cultivated database] to stratify relevant data streams for predictive and actionable capabilities. In addition, EIMO will feature mobility, in that it can be accessed and can push/pull data within and between multiple vehicles/habitats. Large amounts and variable sources of data can be leveraged to diagnose, inform treatment strategies, and potentially predict medical events and performance decrements. Inclusion of advanced training tools using extended reality will enable increasingly autonomous medical care to aid a CMO when ground support is unavailable or time-delayed beyond required action window, e.g., emergent medical situations. EIMO CDSS would require very large datasets to train pre-flight and significant amounts of data are needed to support ML via in-flight CDSS operations. An additional challenge will be to find sufficient data to train a model relevant to astronaut demographics. The rapid, accelerating evolution of this field creates a propitious solution space to leverage multi-modal AI through public-private partnership(s). The status of multi-modal AI systems today would preclude their use for long duration missions as they remain unreliable and are subject to “digital hallucinations” and other errors that could pose operational risk. A federated labs structure is being considered to test and optimize data flow from the multiple input vectors leading to field testing in suitable ground/flight analogs. Critical to the success of an EIMO CDSS will be integration and interoperability and success will be defined by a system that can serve as an in-flight medical consult for the CMO providing critical support during medical contingencies. Benefits to terrestrial medicine may be significant as an outflow of the EIMO medical system, particularly for remote areas and communities lacking significant infrastructure, personnel and resources.

Medical Operations↗

NASA NTRS1966

Forecasts and appraisals for management evaluation, volume 2

Forecasting methodology for Apollo project - weight-performance data, mathematical models, probable error relationships, and manual to computational system

MATHEMATICAL MODEL↗

DOE OSTI2025

HP-MDR: High-performance and Portable Data Refactoring and Progressive Retrieval with Advanced GPUs

Scientific applications produce vast amounts of data, posing grand challenges in the underlying data management and analytic tasks. Progressive compression is a promising way to address this problem, as it allows for on-demand data retrieval with significantly reduced data movement cost. However, most existing progressive methods are designed for CPUs, leaving a gap for them to unleash the power of today’s heterogeneous computing systems with GPUs.In this work, we propose HP-MDR, a high-performance and portable data refactoring and progressive retrieval framework for GPUs. Our contributions are four-fold: (1) We carefully optimize the bitplane encoding and lossless encoding, two key stages in progressive methods, to achieve high performance on GPUs; (2) We propose pipeline optimization and incorporate it with data refactoring and progressive retrieval workflows to further enhance the performance for large data process; (3) We leverage our framework to enable high-performance data retrieval with guaranteed error control for common Quantities of Interest; (4) We evaluate HP-MDR and compare it with state of the arts using five real-world datasets. Experimental results demonstrate that HP-MDR delivers an average 13.68 × and 6.31 × throughput in data refactoring and progressive retrieval tasks, respectively. It also leads to 11.22 × throughput for recomposing required data representations under Quantity-of-Interest error control and 6.04 × performance for the corresponding end-to-end data retrieval, when compared with state-of-the-art solutions.

Li, Yanliang [University of Oregon]↗

DOE OSTI2021

FCET Solid Oxide Fuel Cell Testing and Development: CRADA 526 [Abstract only]

The purpose of the proposed project is for PNNL to test the performance of prototype solid oxide fuel cells (SOFCs) created by FCET. Such testing will provide FCET with independent performance data that can be communicated to potential clients and/or investors. Additionally, PNNL will collaborate with FCET on design changes to improve fuel cell performance. Intellectual property developed in this way will benefit FCET with improved products to market, and PNNL through royalty revenue. The key technology held by FCET is a process to deposit extremely thin layers of oxide materials, from 10-50 nm in thickness. The range of possible materials that can be deposited with their method is broad, but this project will focus on the yttria-stabilized zirconia (YSZ) electrolytes for SOFCs. Thin, gas tight YSZ membranes have been a long-sought target in SOFC research. The thinner the YSZ, the lower the cell resistance, and the higher performance of the cell (or the lower the operating temperature). 10-50 nm would be a major step change in YSZ thickness from the state of the art. PNNL can team with FCET on future R&D projects and push this technology forward to improve energy efficiency and reduce carbon emissions.

30 DIRECT ENERGY CONVERSION↗

NASA NTRS1973

Mariner Mars 1971 sun sensor model development and simulation

The sun sensor flight performance data were analyzed along with the results of a newly developed cruise sensor life in order to better understand cadmium sulfide sun sensor performance. A set of mathematical models was constructed which closely approximated the observed sun sensor flight and laboratory test results. These models revealed, among other things, that (1) the aging phenomena in the sintered cadmium sulfide light detector varies across the detector width in proportion to the illumination history, (2) the current cruise sun sensor design is extremely sensitive to changes in the reflected illumination within the sensor housing, (3) the reflected illumination within the detector housing is proportional to the area and intensity of the solar disk observed at the spacecraft, and (4) the acquisition sun sensor becomes a low impedance path across the sensor bridge when in the vicinity of a large-angular-diameter, low-intensity light source.

Schumacher, L.↗