SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
This paper will describe the ways in which the Cassini Remote Terminal Interface Units were upgraded and enhanced to support flight operations during the Cassini tour of Saturn.
To date the air transportation system has been developed with the in-cremental introduction of new technology and with highly experienced air transport pilots and air traffic controllers overseeing flight operations. Thus, we currently have one of the safest commercial aviation systems in the world. General Aviation (GA) in the United States, however, has not always followed the same cautious and monitored approach to implementation; consequently, the GA safety record does not meet the high standards of commercial aviation. Recently, a new system known as Urban Air Mobility (UAM), is attracting considerable interest and investment from industry and government agencies. UAM refers to a system of passenger and small-cargo air transportation vehicles within an urban area with the goal of reducing the number of times we need to use our cars, thus improving urban traffic by moving people and cargo from crowded single pas-senger vehicles on our roads to personal and on-demand air vehicles. These UAM vehicles will be small and based on electric, Vertical-Take-Off-and-Landing (eV-TOL) systems. A significant component of UAM is offloading of flight-man-agement responsibilities from human pilots to newly-developed autonomy. Cur-rently, over 100 UAM vehicles are either in development or production. Most, if not all, have a goal of fully autonomous vehicle operations, but fully autonomous flying vehicles are not expected in the near future. Therefore, we are de-veloping concepts for UAM vehicles that will be easy to fly and/or manage by operators with minimal pilot training. In this paper we will discuss our human-automation teaming approach to develop an easy-to-operate VTOL aircraft, and some of the fly-by-wire technology needed to stabilize the vehicle so that a sim-ple ecological mental model of the flying task can be implemented. We will discuss the requirements for a stability augmentation system that must be developed to support our simple pilot input model, and also present design guidelines and requirements based on a pilot input and management model. Finally, our ap-proach to vehicle development will involve considerable operator testing and evaluation: improving pilot model, inceptors, displays and also work on a plan for how a UAM vehicle can be integrated with terminal area air traffic control airspace with minimal impact on controller workload.
This document provides a preliminary validation of the Small Aircraft Transportation System (SATS) Higher Volume Operations (HVO) concept for normal conditions. Initial results reveal that the concept provides reduced air traffic delays when compared to current operations without increasing pilot workload. Characteristic to the SATS HVO concept is the establishment of a newly defined area of flight operations called a Self-Controlled Area (SCA) which would be activated by air traffic control (ATC) around designated non-towered, non-radar airports. During periods of poor visibility, SATS pilots would take responsibility for separation assurance between their aircraft and other similarly equipped aircraft in the SCA. Using onboard equipment and simple instrument flight procedures, they would then be better able to approach and land at the airport or depart from it. This concept would also require a new, ground-based automation system, typically located at the airport that would provide appropriate sequencing information to the arriving aircraft. Further validation of the SATS HVO concept is required and is the subject of ongoing research and subsequent publications.
This document expands the Small Aircraft Transportation System, (SATS) Higher Volume Operations (HVO) concept to include off-nominal conditions. The general philosophy underlying the HVO concept is the establishment of a newly defined area of flight operations called a Self-Controlled Area (SCA). During periods of poor weather, a block of airspace would be established around designated non-towered, non-radar airports. Aircraft flying enroute to a SATS airport would be on a standard instrument flight rules flight clearance with Air Traffic Control providing separation services. Within the SCA, pilots would take responsibility for separation assurance between their aircraft and other similarly equipped aircraft. Previous work developed the procedures for normal HVO operations. This document provides details for off-nominal and emergency procedures for situations that could be expected to occur in a future SCA.
The results of electrical power system (EPS) analysis of the planned Shuttle Transportation System Flight 1 mission are presented. The capability of the orbiter EPS to support the planned flight and to provide program tape information and supplementary data specifically requested by the flight operations directorate was assessed. The analysis was accomplished using the orbiter version of the spacecraft electrical power simulator program, operating from a modified version of orbiter electrical equipment utilization baseline revision four. The results indicate that the nominal flight, as analyzed, is within the capabilities of the orbiter power generation system, but that a brief, and minimal, current overload may exist between main distributor 1 and mid power controlled 1, and that inverter 9 may the overloaded for extended periods of time. A comparison of results with launch commit criteria also indicated that some of the presently existing launch redlines may be violated during the terminal countdown.
The Infrared Astronomical Satellite (IRAS) was launched on January 25, 1983, and has provided astronomers with their first extended views of the universe in the 8 to 120 micron wavelength region. The infrared telescope system is one of several United States contributions to this international project sponsored by the U.S.A., The Netherlands, and the U.K. This telescope employs four bands of detectors cooled to 2.4 K to achieve a noise equivalent flux density in the 10 to the -18th to 10 to the -19th watts/sq cm range and will operate for approximately eleven months before depletion of its supply of superfluid helium. This paper describes major problems, early flight results, and technical lessons learned during the course of the telescope's development and flight operations.
On November 25, 1985, the NASA Chief Engineer established a NASA-wide policy to maintain and to require the use of the NASA standard for aerospace nickel-cadmium cells and batteries. The Associate Administrator for Safety, Reliability, Maintainability, and Quality Assurance stated on December 29, 1986, the intent to retain the NASA standard cell usage policy established by the Office of the Chief Engineer. The current NASA policy is also to incorporate technological advances as they are tested and proven for spaceflight applications. This policy will be implemented by modifying the existing standard cells or by developing new NASA standards and their specifications in accordance with the NASA's Aerospace Battery Systems Program Plan. This NASA Specification for Manufacturing and Performance Requirements of NASA Standard Aerospace Nickel-Cadmium Cells is prepared to provide requirements for the NASA standard nickel-cadmium cell. It is an interim specification pending resolution of the separator material availability. This specification has evolved from over 15 years of nickel-cadmium cell experience by NASA. Consequently, considerable experience has been collected and cell performance has been well characterized from many years of ground testing and from in-flight operations in both geosynchronous (GEO) and low earth orbit (LEO) applications. NASA has developed and successfully used two standard flight qualified cell designs.
The Operational Science Analysis (OSA) Functional area supports science instrument data display, analysis, visualization and photo processing in support of flight operations of planetary spacecraft managed by the Jet Propulsion Laboratory (JPL). This paper describes the data products generated by the OSA functional area, and the current computer system used to generate these data products. The objectives on a system upgrade now in process are described. The design approach to development of the new system are reviewed, including use of the Unix operating system and X-Window display standards to provide platform independence, portability, and modularity within the new system, is reviewed. The new system should provide a modular and scaleable capability supporting a variety of future missions at JPL.
Flight tests were recently completed to demonstrate an inlet-distortion-tolerant engine control system. These flight tests were part of NASA's High Stability Engine Control (HISTEC) program. The objective of the HISTEC program was to design, develop, and flight demonstrate an advanced integrated engine control system that uses measurement-based, real-time estimates of inlet airflow distortion to enhance engine stability. With improved stability and tolerance of inlet airflow distortion, future engine designs may benefit from a reduction in design stall-margin requirements and enhanced reliability, with a corresponding increase in performance and decrease in fuel consumption. This paper describes the HISTEC methodology, presents an aircraft test bed description (including HISTEC-specific modifications) and verification and validation ground tests. Additionally, flight test safety considerations, test plan and technique design and approach, and flight operations are addressed. Some illustrative results are presented to demonstrate the type of analysis and results produced from the flight test program.
The objective of this paper is to provide the future ISS scientist and/or engineer a sense of what ISS payload operations are expected to be. This paper uses a real-time operations scenario to convey this message. The real-time operations scenario begins at the initiation of payload operations and runs through post run experiment analysis. In developing this scenario, it is assumed that the ISS payload operations flight and ground capabilities are fully available for use by the payload user community. Emphasis is placed on telescience operations whose main objective is to enable researchers to utilize experiment hardware onboard the International Space Station as if it were located in their terrestrial laboratory. An overview of the Payload Operations Integration Center (POIC) systems and user ground system options is included to provide an understanding of the systems and interfaces users will utilize to perform payload operations. Detailed information regarding POIC capabilities can be found in the POIC Capabilities Document, SSP 50304.
The Advanced Transport Operating System (ATOPS) project is a NASA operational research flight project which is concerned with upgrading the new generation of flight computers. In connection with this work, it becomes also necessary to reassess the adequacy of the flight executive and flight software. In the present discussion, attention is given to the ATOPS project upgrade, the operating flight system, the design criteria for the new flight executive, the implementation of the executive, a sample real-time execution, a real-time debug and test tool, and several experiences which could be useful to others considering a similar exercise.
Since 1972, NASA astronauts have performed hundreds of Extravehicular Activities (EVAs) in support of Skylab, Space Shuttle and International Space Station missions. Not since Apollo, however, have EVAs been driven by discovery-based principles of scientific exploration. Upcoming Artemis missions are challenged to build on lessons learned from Apollo, merging 50 years of EVA experience with the planetary science community’s expertise in the remote surface exploration of Mars. The highest-fidelity preparation for Artemis includes both operational and scientific underpinning to represent the complete, complex picture of lunar surface operations. The Joint EVA & Human Surface Mobility Test Team (JETT) is an interdisciplinary team providing such an environment for collaborative analog testing. JETT builds upon prior analog campaigns (e.g., [1, 2]) to provide high-fidelity environments for hardware and concept of operations development. Sponsored by the NASA EVA & Human Surface Mobility Program (EHP), JETT includes representatives from EHP, NASA Engineering, the Science Mission Directorate (SMD), Human Health & Performance, and the Flight Operations Directorate (FOD). JETT tests evaluate NASA reference designs for EVA (e.g., suits and tools), address gaps and risks for Artemis lunar surface operations, develop capabilities for EVA and science tasks, enable technology maturation, and provide training for Artemis EVA operations. JETT3, the final JETT field test of FY22, occurred Oct 3-11, 2022 in the San Francisco Volcanic Field north of Flagstaff, AZ. The test focused on developing the Artemis concept of operations and systems, including integrating an Artemis-like Science Team into a NASA Flight Control Team (FCT) to plan and execute a series of simulated lunar EVAs in an environment analogous to Artemis 3.
Since 1972, NASA astronauts have performed hundreds of Extravehicular Activities (EVAs) in support of Skylab, Space Shuttle and International Space Station missions. Not since Apollo, however, have EVAs been driven by discovery-based principles of scientific exploration. Upcoming Artemis missions are challenged to build on lessons learned from Apollo, merging 50 years of EVA experience with the planetary science community’s expertise in the remote surface exploration of Mars. The highest-fidelity preparation for Artemis includes both operational and scientific underpinning to represent the complete, complex picture of lunar surface operations. The Joint EVA & Human Surface Mobility Test Team (JETT) is an interdisciplinary team providing such an environment for collaborative analog testing. JETT builds upon prior analog campaigns (e.g., [1, 2]) to provide high-fidelity environments for hardware and concept of operations development. Sponsored by the NASA EVA & Human Surface Mobility Program (EHP), JETT includes representatives from EHP, NASA Engineering, the Science Mission Directorate (SMD), Human Health & Performance, and the Flight Operations Directorate (FOD). JETT tests evaluate NASA reference designs for EVA (e.g., suits and tools), address gaps and risks for Artemis lunar surface operations, develop capabilities for EVA and science tasks, enable technology maturation, and provide training for Artemis EVA operations. JETT3, the final JETT field test of FY22, occurred Oct 3-11, 2022 in the San Francisco Volcanic Field north of Flagstaff, AZ. The test focused on developing the Artemis concept of operations and systems, including integrating an Artemis-like Science Team into a NASA Flight Control Team (FCT) to plan and execute a series of simulated lunar EVAs in an environment analogous to Artemis 3.
This document serves as a user manual for the ATD-2 Metroplex Planner (version 5.11) utilized by the Air Route Traffic Control Center (ARTCC), Terminal Radar Approach Control (TRACON), airport ATC Towers, and by Flight Operators. It describes the elements of the Metroplex Planner interface and provides step-by-step instructions for using the tool. Metroplex Planner functionality includes the display of live flight information, management of traffic restrictions, prediction of expected traffic demand/delay, andTrajectory Option Set (TOS) Operations. The Metroplex Planner is a component of the NASA Airspace Technology Demonstration 2 (ATD-2) sub-project.
The flying qualities of the CV-990 jet transport were evaluated over the normal operating flight envelope and in smooth air to provide baseline data for transport airplanes. Pilot ratings of airplane handling characteristics for specific test conditions and configurations from approach to normal cruise were compared with various flying qualities criteria. In general, the CV-990 flying qualities were evaluated as satisfactory, and the evaluations supported transport flying qualities criteria. The Dutch roll damping was rated more satisfactory than was predicted by the flying qualities criteria. The pilots found rudder coordination for the yaw generated during high roll rates very difficult. They preferred to control with roll and pitch controls and to use the yaw damper to provide the required rudder coordination.
An inviscid technique for designing forebodies which produce uniformly precompressed flows at the inlet entrance for bottom-mounted scramjets has been developed so that geometric constraints resulting from design trade-offs can be effectively evaluated. The flow fields resulting from several forebody designs generated in support of a hypersonic research airplane conceptual design study have been analyzed in detail with three-dimensional characteristics calculations to verify the uniform flow conditions. For the designs analyzed, uniform flow is maintained over a wide range of flight conditions (Mach number equals 4 to 10; angle of attack equals 6 deg to 10 deg) corresponding to scramjet operation flight envelope of the research airplane.
A rapid and simple inviscid technique for designing forebodies which produce uniformly precompressed flows at the entrance for bottom-mounted scramjets was developed so that geometric constraints resulting from design trade-offs can be effectively evaluated. The flow fields resulting from several forebody designs generated in support of a conceptual design for a hypersonic research airplane have been analyzed in detail. Three-dimensional characteristics calculations were used to verify the uniform flow conditions. For the designs analyzed, uniform flow was maintained over a wide range of flight conditions (Mach numbers from 4 to 10; angles of attack of 6 and 10 deg) corresponding to the scramjet operation flight envelope of the research airplane.
The HEAO (High Energy Astronomy Observatory) Program consists of three large automated scientific observatories launched between 1977 and 1979 to observe from near-earth orbit stellar X-ray and gamma-ray sources and to measure incoming cosmic ray particles. The HEAO-2 and HEAO-3 spacecraft are expected to exceed their design lifetimes by a factor of three, as did HEAO-1, which operated for 18 months. All three missions are considered successful in that target dates have essentially been met, launch and flight operations have been relatively smooth, instrumentation has performed well, and there have been no cost overruns. The paper lists ten factors contributing to the missions' success, among them a thorough definition before program start, commonality of spacecraft design, redundancy of mission critical equipment, ample design margins, and tight control of system changes. Specific mission parameters are included in the paper as well as the technological advances engendered by the HEAO Program in such areas as high-resolution X-ray optics and solid-state spectrometry.