Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “open systems”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
DOE OSTI2013

Avoiding compressor surge during emergency shutdown hybridturbine systems

A new emergency shutdown procedure for a direct-fired fuel cell turbine hybrid power system was evaluated using a hardware-based simulation of an integrated gasifier/fuel cell/turbine hybrid cycle (IGFC), implemented through the Hybrid Performance (Hyper) project at the National Energy Technology Laboratory, U.S. Department of Energy (NETL). The Hyper facility is designed to explore dynamic operation of hybrid systems and quantitatively characterize such transient behavior. It is possible to model, test, and evaluate the effects of different parameters on the design and operation of a gasifier/fuel cell/gas turbine hybrid system and provide a means of quantifying risk mitigation strategies. An open-loop system analysis regarding the dynamic effect of bleed air, cold air bypass, and load bank is presented in order to evaluate the combination of these three main actuators during emergency shutdown. In the previous Hybrid control system architecture, catastrophic compressor failures were observed when the fuel and load bank were cut off during emergency shutdown strategy. Improvements were achieved using a nonlinear fuel valve ramp down when the load bank was not operating. Experiments in load bank operation show compressor surge and stall after emergency shutdown activation. The difficulties in finding an optimal compressor and cathode mass flow for mitigation of surge and stall using these actuators are illustrated.

20 FOSSIL-FUELED POWER PLANTS↗
NASA NTRS1966

Automatic protective vent has fail-safe feature

Delayed vent valve system in a mechanical backing pump in a vacuum system allows the pneumatic foreline valve to seal before the pump vent opens. The system is designed to be fail-safe and operate even though there is loss of electrical power.

Dameron, C. E.↗
NASA NTRS1970

Flueric-controller pneumatic stepping motor system

Nutating stepping motor consists of an output rotating gear and a nutating gear. A flueric logic circuit controls the nutating motor. The complete system constitutes a reliable, open loop actuator system with inherently high output stiffness, reasonable slewing speeds and small step size.

Dustin, M. O.↗
NASA NTRS1972

Loudness (annoyance), prediction procedure for steady sounds

Method has been devised to predict loudness level of any steady sound solely from its measured power spectrum level. Method is based on assumption that, with respect to loudness sensation, the human auditory system acts as open-loop transmission system with transmittance function determined from measured tone curves.

Howes, W. L.↗
NASA NTRS2019

Aqueous Alteration on Mars

The occurrence of extensive valley networks and layered deposits of phyllosilicates and sulfates during the late Noachian/Hesperian periods (approx. 3-4 Gyrs) indicates a past martian climate that was capable of maintaining liquid water at the surface. The planet’s climate drastically changed after these early “episodes” of water to a drier and colder environment during the Amazonian period (past 3.0 Gyrs). The objective of this paper is to describe aqueous alteration/weathering scenarios on Mars based on observations returned by rover and lander missions. The chemistry of most outcrops, rocks, and “soils” that have interacted with water has not been extensively changed from average Mars crustal basaltic composition. Little chemical variation suggests closed hydrologic systems were prominent on early Mars and/or the water/rock ratios were low. Open hydrologic systems occur at local scales, e.g., high Si and Ti rocks and “soil” deposits around a volcanic feature in Gusev crater. Geochemical and mineralogical indicators for aqueous alteration include jarosite and other Fe-sulfates at several locations suggesting acid-sulfate alteration conditions. High Si and Ti rocks, sediments, and “soil” deposits are consistent with basaltic residues extenively leached by extremely acidic fluids. Variations in the Fe/Mn ratio of fracture veins infilled with sulfate-rich materials suggest changes in redox and/or pH conditions of the migrating fluids. The increase of nanophase iron oxides and salts with depth in several “soil” pits escavated by the Spirit rover’s wheel in Gusev crater suggests the translocation/mobolization of these phases by liquid water. This “pedogenic” process is the result of limited water movement through the surface sediments during the Amazonian period; however, it is likely that paleosols exist on Mars that formed during the early “wetter” history of the planet. Soil scientists have the opportunity to continue to (and should) be involved in the exploration of the Red planet.

Ming, Douglas W.↗
DOE OSTI2022

A multisite decomposition of the tensor network path integrals

Tensor network decompositions of path integrals for simulating open quantum systems have recently been proven to be useful. However, these methods scale exponentially with the system size. This makes it challenging to simulate the non-equilibrium dynamics of extended quantum systems coupled with local dissipative environments. In this work, we extend the tensor network path integral (TNPI) framework to efficiently simulate such extended systems. The Feynman–Vernon influence functional is a popular approach used to account for the effect of environments on the dynamics of the system. In order to facilitate the incorporation of the influence functional into a multisite framework (MS-TNPI), we combine a matrix product state (MPS) decomposition of the reduced density tensor of the system along the sites with a corresponding tensor network representation of the time axis to construct an efficient 2D tensor network. The 2D MS-TNPI network, when contracted, yields the time-dependent reduced density tensor of the extended system as an MPS. The algorithm presented is independent of the system Hamiltonian. We outline an iteration scheme to take the simulation beyond the non-Markovian memory introduced by solvents. Applications to spin chains coupled to local harmonic baths are presented; we consider the Ising, XXZ, and Heisenberg models, demonstrating that the presence of local environments can often dissipate the entanglement between the sites. We discuss three factors causing the system to transition from a coherent oscillatory dynamics to a fully incoherent dynamics. The MS-TNPI method is useful for studying a variety of extended quantum systems coupled with solvents.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
NASA NTRS2018

How NASA is Building a Petabyte Scale Geospatial Archive in the Cloud

NASA's Earth Observing System Data and Information System (EOSDIS) is working towards a vision of a cloud-based, highly-flexible, ingest, archive, management, and distribution system for its ever-growing and evolving data holdings. This free and open source system, Cumulus, is emerging from its prototyping stages and is poised to make a huge impact on how NASA manages and disseminates its Earth science data. This talk outlines the motivation for this work, present the achievements and hurdles of the past 18 months and charts a course for the future expansion of Cumulus. We explore not just the technical, but also the socio-technical challenges that we face in evolving a system of this magnitude into the cloud. The NASA EOSDIS archive is currently at nearly 30 PBs and will grow to over 300PBs in the coming years. We've presented progress on this effort at AWS re:Invent and the American Geophysical Union (AGU) Fall Meeting in 2017 and hope to have the opportunity to share with FOSS4G attendees information on the availability of the open sourced software and how NASA intends on making its Earth Observing Geospatial data available for free to the public in the cloud.

NASA Archive↗
NASA NTRS1991

Alleviation of whirl-flutter on a joined-wing tilt-rotor aircraft configuration using active controls

The feasibility of using active controls to delay the onset of whirl-flutter on a joined-wing tilt rotor aircraft was investigated. The CAMRAD/JA code was used to obtain a set of linear differential equations which describe the motion of the joined-wing tilt-rotor aircraft. The hub motions due to wing/body motion is a standard input to CAMRAD/JA and were obtained from a structural dynamics model of a representative joined-wing tilt-rotor aircraft. The CAMRAD/JA output, consisting of the open-loop system matrices, and the airframe free vibration motion were input to a separate program which performed the closed-loop, active control calculations. An eigenvalue analysis was performed to determine the flutter stability of both open- and closed-loop systems. Sensor models, based upon the feedback of pure state variables and based upon hub-mounted sensors, providing physically measurable accelerations, were evaluated. It was shown that the onset of tilt-rotor whirl-flutter could be delayed from 240 to above 270 knots by feeding back vertical and span-wise accelerations, measured at the rotor hub, to the longitudinal cyclic pitch. Time response calculations at a 270-knot cruise condition showed an active cyclic pitch control level of 0.009 deg, which equates to a very acceptable 9 pound active-control force applied at the rotor hub.

Vanaken, Johannes M.↗
NASA NTRS1990

Advanced data management system architectures testbed

The objective of the Architecture and Tools Testbed is to provide a working, experimental focus to the evolving automation applications for the Space Station Freedom data management system. Emphasis is on defining and refining real-world applications including the following: the validation of user needs; understanding system requirements and capabilities; and extending capabilities. The approach is to provide an open, distributed system of high performance workstations representing both the standard data processors and networks and advanced RISC-based processors and multiprocessor systems. The system provides a base from which to develop and evaluate new performance and risk management concepts and for sharing the results. Participants are given a common view of requirements and capability via: remote login to the testbed; standard, natural user interfaces to simulations and emulations; special attention to user manuals for all software tools; and E-mail communication. The testbed elements which instantiate the approach are briefly described including the workstations, the software simulation and monitoring tools, and performance and fault tolerance experiments.

Grant, Terry↗
NASA NTRS1994

Personal cooling systems: Possibilities and limitations

Personal thermal control by means of gas- or liquid-conditioned garments was developed during the 1960s and has been applied in a variety of aerospace and industrial settings. Both USAF fighter pilots and astronauts are required to wear heavy protective clothing which insulates them from the environment and thus creates stress through storage of metabolic heat. The problem is particularly severe in astronauts who perform heavy physical work during extra-vehicular activity (EVA); without artificial cooling they could reach incapacitating hyperthermia in a matter of minutes. This paper reviews the factors which influence the design of personal cooling systems. An important early step is determination of acceptable heat stress level, taking into account possible interactions of heat stress with other physiological problems such as motion sickness, diminished plasma volume, decompression sickness and acceleration tolerance. Other factors which require consideration include the work schedule, the area to be covered by the cooling garment, and the practicalities of a fixed or body-mounted heat sink and its power source. Nearly every imaginable heat sink has been proposed or tried over the past 30 years, including direct gas systems, phase-change systems with open or closed loops and thermoelectric heat sinks. The latter are now the system of choice for aircraft.

Nunneley, Sarah A.↗
DOE OSTI2017

High temperature high velocity direct power extraction using an open-cycle oxy-combustion system

The implementation of oxy-fuel technology in fossil-fuel power plants may contribute to increased system efficiencies and a reduction of pollutant emissions. One technology that has potential to utilize the temperature of undiluted oxy-combustion flames is open-cycle magnetohydrodynamic (MHD) power generators. These systems can be configured as a topping cycle and provide high enthalpy, electrically conductive flows for direct conversion of electricity. This report presents the design and modeling strategies of a MHD combustor operating at temperatures exceeding 3000 K. Throughout the study, computational fluid dynamics (CFD) models were extensively used as a design and optimization tool. A lab-scale 60 kWth model was designed, manufactured and tested as part of this project. A fully-coupled numerical method was developed in ANSYS FLUENT to characterize the heat transfer in the system. This study revealed that nozzle heat transfer may be predicted through a 40% reduction of the semi-empirical Bartz correlation. Experimental results showed good agreement with the numerical evaluation, with the combustor exhibiting a favorable performance when tested during extended time periods. A transient numerical method was employed to analyze fuel injector geometries for the 60-kW combustor. The ANSYS FLUENT study revealed that counter-swirl inlets achieve a uniform pressure and velocity ratio when the ports of the injector length to diameter ratio (L/D) is 4. An angle of 115 degrees was found to increase distribution efficiency. The findings show that this oxy-combustion concept is capable of providing a high-enthalpy environment for seeding, in order to render the flow to be conductive. Based on previous findings, temperatures in the range of 2800-3000 K may enable magnetohydrodynamic power extraction. The heat loss fraction in this oxy-combustion system, based on CFD and analytical calculations, at optimal operating conditions, was estimated to be less than 10 percent. Furthermore, the heat transfer design removed approximately 7 MW/m2. The results observed in the lab-scale system were employed to develop a 1-MW scaled prototype. Scaling methods were based on critical design criteria found in similar systems, aimed at replicating combustion flow fields and reducing possible instabilities. A numerical simulation of the combustor wall was developed for a combined thermal steady model and static structural model. This combined model was developed predict combined stress parameters within the wall during testing conditions. Both models were developed within ANSYS FEA software package. The relative accuracy presented as well major performance parameters are discussed to assess the design's validity and ensure safety. The scaled prototype was manufactured through selective laser melting (SLM)-based additive manufacturing to reduce lead times and increase geometrical complexity. Additional CFD models were developed to optimize coolant manifold system parameters and perform a parametric study on channel geometry. An investigation on coolant manifold geometry demonstrated improvements in channel flow distribution when enlarging manifold lengths and increasing the number of tubes feeding into the flow. A three-dimensional model based on a single channel was developed to capture the effect of variable properties and thermal stratification. All cases in the simulation exhibited higher wall temperatures and lower convective coefficients than those determined through 1-D analytical equations. This implies that pressure and velocity safety factors must be implemented during system operation. Overall, the findings made in this investigation are thought to be of value to researchers and industrial practitioners when designing oxy-fuel direct power extraction systems operating at temperatures exceeding 3000 K. In addition to this, the implementation of the developed technology at pilot and commercial scales could result in a significant improvement in the efficiencies of heritage and next-generation power cycles.

03 NATURAL GAS↗
DOE OSTI2024

Bottomonium suppression in 5.02 and 8.16 TeV 𝑝-Pb collisions

Here, we compute the suppression of ϒ⁡(1⁢𝑆), ϒ⁡(2⁢𝑆), and ϒ⁡(3⁢𝑆) states in 𝑝-Pb collisions relative to 𝑝⁢𝑝 collisions, including nuclear parton distribution function (nPDF) effects, coherent energy loss, momentum broadening, and final-state interactions in the quark-gluon plasma. We employ the EPPS21 nPDFs and calculate the uncertainty resulting from variation over the associated error sets. To compute coherent energy loss and momentum broadening, we follow the approach of Arleo, Peigne, and collaborators. The 3+1⁢D viscous hydrodynamical background evolution of the quark-gluon plasma is generated by anisotropic hydrodynamics. The in-medium suppression of bottomonium in the quark-gluon plasma is computed using a next-to-leading-order open quantum system framework formulated within potential nonrelativistic quantum chromodynamics. We find that inclusion of all these effects provides a reasonable description of experimental data from the ALICE, ATLAS, CMS, and LHCb Collaborations for the suppression of ϒ⁡(1⁢𝑆), ϒ⁡(2⁢𝑆), and ϒ⁡(3⁢𝑆) as a function of both transverse momentum and rapidity.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗
DOE OSTI2024

How to Partition a Quantum Observable

We present a partition of quantum observables in an open quantum system that is inherited from the division of the underlying Hilbert space or configuration space. It is shown that this partition leads to the definition of an inhomogeneous continuity equation for generic, non-local observables. This formalism is employed to describe the local evolution of the von Neumann entropy of a system of independent quantum particles out of equilibrium. Crucially, we find that all local fluctuations in the entropy are governed by an entropy current operator, implying that the production of entanglement entropy is not measured by this partitioned entropy. For systems linearly perturbed from equilibrium, it is shown that this entropy current is equivalent to a heat current, provided that the system-reservoir coupling is partitioned symmetrically. Finally, we show that any other partition of the coupling leads directly to a divergence of the von Neumann entropy. Thus, we conclude that Hilbert-space partitioning is the only partition of the von Neumann entropy that is consistent with the laws of thermodynamics.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗
DOE OSTI2022

WinnowML: Stable feature selection for maximizing prediction accuracy of time-based system modeling

Online deep learning (ODL) has become an important methodology for modeling time-based performance of computer systems. An open problem is the intelligent selection of features from raw workload traces of computer systems. The best methods are overly sensitive to noisy data, causing frequent feature changes and re-training. Using all available features inflates training time and introduces model artifacts if some features should have been dropped. We present WinnowML, a method for automatically determining the most relevant feature subset for a predictive time-series model. WinnowML combines existing feature ranking algorithms and a history of each feature's ranking to iteratively rank a feature set to lower prediction error and maximize long term relevance. From this ranked feature set, the most relevant and stable subset is selected to train a model. Experimentally, we show how WinnowML can lower a model's mean absolute relative error up to 42% on average compared to the closest performing approach. Additionally, we lower the fluctuation in feature ranking and selection up to 65%. We also demonstrate how to combine WinnowML and a model search tool to provide improvements in performance of up to 14.5% when compared to using all the feature available.

Bel, Oceane MS↗
DOE OSTI2018

Monte Carlo-Based Method for Parallelizing Quasi-Static Time-Series Power System Simulations: Preprint

Both commercial and open source power system simulators run quasi-static time-series (QSTS) simulations sequentially. For yearlong high-resolution load profiles this sequential execution of load flows incurs long computation times. Parallelizing QSTS simulations on multiple processors is one possible way to reduce the computation time. Parallelization however introduces errors in the simulation results as the initial state of the system at the beginning of each parallelized time period is not known. In this work a Monte Carlo-based approach has been proposed to estimate the initial state of the system for each parallel simulation run to mitigate the errors in the final results. Classical sequential QSTS simulation is the chosen base case against which all other methods have been compared. Results presented in this paper show that the proposed method improves the simulation results considerably. This paper also discusses possible sensitivities of the proposed method to a number of tunable parameters. Additionally, sensitivity analysis results for a number of parameters have also been presented in the results section.

24 POWER TRANSMISSION AND DISTRIBUTION↗
NASA NTRS1984

Engineering model system study for a regenerative fuel cell: Study report

Key design issues of the regenerative fuel cell system concept were studied and a design definition of an alkaline electrolyte based engineering model system or low Earth orbit missions was completed. Definition of key design issues for a regenerative fuel cell system include gaseous reactant storage, shared heat exchangers and high pressure pumps. A power flow diagram for the 75 kW initial space station and the impact of different regenerative fuel cell modular sizes on the total 5 year to orbit weight and volume are determined. System characteristics, an isometric drawing, component sizes and mass and energy balances are determined for the 10 kW engineering model system. An open loop regenerative fuel cell concept is considered for integration of the energy storage system with the life support system of the space station. Technical problems and their solutions, pacing technologies and required developments and demonstrations for the regenerative fuel cell system are defined.

Chang, B. J.↗
NASA NTRSDate not supplied

Validation of the NASA Electrical Power System – Sizing and Analysis Tool (EPS-SAT)

The electrification of aircraft propulsion systems has opened the design space for engineers by allowing for unique and highly specialized propulsion system and vehicle designs. NASA developed the Electrical Power System – Sizing and Analysis Tool (EPS-SAT) to conduct high-level trade studies and sensitivity studies on the various propulsion system designs that can be implemented in electrified aircraft. The results of these studies would be used to better direct investment dollars and determine strengths and weaknesses of propulsion system designs. In this paper, the results of the EPS-SAT tool were validated with hardware data extracted from the NASA Revolutionary Vertical Lift Technology (RVLT) Advanced Reconfigurable Electric Aircraft Lab (AREAL). Updated performance maps were added to the EPS-SAT library so that high-fidelity results could be calculated.

Patrick A. Hanlon↗
DOE OSTI2024

A Survey of Open-Source Tools for Transmission and Distribution Systems Research

This work presents a review of open-source electric power transmission and distribution systems analysis tools suitable for use by industry professionals and academic researchers. Due to the high complexity of the electric grid, there exist numerous tools and extensive research pertaining to nearly every aspect of the design, operation, and control of transmission and distribution networks. In addition to the commercial tools, a wide range of free, open-source tools, models, and data usable by the scientific community for related research have been developed by different organizations, including both international and US universities and national laboratories. However, due to the absence of a catalog of available tools, models and data, researchers often lack a knowledge of existing capabilities and may develop duplicative software and tools. Increasing awareness of these available resources seeks to accelerate their broader use, leading to more efficient and standardized grid analysis. This review paper (which is part of a larger survey effort that studied over 400 tools in the transmission, distribution, buildings, and electric vehicles space) outlines selected open-source resources that have been developed in power transmission and distribution systems research. It is anticipated that this work can serve as a guide for industry and academic researchers alike, ensuring that research efforts are well-channeled.

24 POWER TRANSMISSION AND DISTRIBUTION↗