Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS1993

Dynamic Hardness Tester and Cure Meter

The Shore hardness tester is used extensively throughout industry to determine the static modulus of materials. The new apparatus described here extends the capability of an indentor-type tester into the dynamic regime, and provides a measurement of the dynamic shear or Young's modulus and loss factor as a function of frequency. The instrument, model and data of typical rubber samples are given and compared to other dynamic measurements.

Madigosky, Walter M.↗
NASA NTRS1991

Combined micromechanical and fabrication process optimization for metal-matrix composites

A method is presented to minimize the residual matrix stresses in metal matrix composites. Fabrication parameters such as temperature and consolidation pressure are optimized concurrently with the characteristics (i.e., modulus, coefficient of thermal expansion, strength, and interphase thickness) of a fiber-matrix interphase. By including the interphase properties in the fabrication process, lower residual stresses are achievable. Results for an ultra-high modulus graphite (P100)/copper composite show a reduction of 21 percent for the maximum matrix microstress when optimizing the fabrication process alone. Concurrent optimization of the fabrication process and interphase properties show a 41 percent decrease in the maximum microstress. Therefore, this optimization method demonstrates the capability of reducing residual microstresses by altering the temperature and consolidation pressure histories and tailoring the interphase properties for an improved composite material. In addition, the results indicate that the consolidation pressures are the most important fabrication parameters, and the coefficient of thermal expansion is the most critical interphase property.

Morel, M.↗
NASA NTRS1993

Multichannel astrometric photometer parallax studies in the regions of Groombridge 1618, Zeta Bootis, and Sigma Draconis

Improved trigonometric parallaxes are reported for stars in the regions of Groombridge 1618, Zeta Bootis, and Sigma Draconis which differ from generally accepted parallaxes by two to five standard deviations. The weighted mean parallax of Groombridge 1618 becomes 0.2079 +/- 0.0013 arcsec, indicating a distance modulus of -1.59 +/- 0.014 and yielding an absolute magnitude of this K7 V star of 8.20 +/- 0.017. The parallax determined for the visual binary Zeta Bootis is 0.0202 +/- 0.0010 arcsec and implies an average absolute visual magnitude of 1.067 +/- 0.12 for the spectroscopically similar components. The weighted mean parallax of Sigma Draconis becomes 0.1747 +/- 0.0010 arcsec, indicating a distance modulus of -1.210 +/- 0.012 and yielding an absolute visual magnitude of 5.90 +/- 0.012 for this K0 V star. The absolute visual magnitudes of the high velocity star Roman 336 and of the subdwarf star AO 1187 are found to be + 4.0 +/- 0.13 and + 5.9 +/- 0.17, respectively.

Gatewood, George↗
NASA NTRS1993

Probabilistic and structural reliability analysis of laminated composite structures based on the IPACS code

Probabilistic predictions based on the Integrated Probabilistic Assessment of Composite Structures (IPACS) code are presented for the material and structural response of unnotched and notched, 1M6/3501-6 Gr/Ep laminates. Comparisons of predicted and measured modulus and strength distributions are given for unnotched unidirectional, cross-ply, and quasi-isotropic laminates. The predicted modulus distributions were found to correlate well with the test results for all three unnotched laminates. Correlations of strength distributions for the unnotched laminates are judged good for the unidirectional laminate and fair for the cross-ply laminate, whereas the strength correlation for the quasi-isotropic laminate is deficient because IPACS did not yet have a progressive failure capability. The paper also presents probabilistic and structural reliability analysis predictions for the strain concentration factor (SCF) for an open-hole, quasi-isotropic laminate subjected to longitudinal tension. A special procedure was developed to adapt IPACS for the structural reliability analysis. The reliability results show the importance of identifying the most significant random variables upon which the SCF depends, and of having accurate scatter values for these variables.

Sobel, Larry↗
NASA NTRS1990

Application of the embedded atom method to Pb and Be

We have derived the embedding energy functional and two-body potential of the embedded atom method using decreasing exponentials for both the electron density and the two body potential. The embedding function was obtained from the equation of state given by Rose et al. (1984). Because of the form of the embedding function, the equilibrium lattice constant, cohesive energy, and bulk modulus are automatically satisfied. The two parameters phi(e) and gamma of the two-body potential were determined by fitting to shear modulus and the single vacancy formation energy. Contributions of up to the third nearest neighbors were included in the evaluation of the charge density rho and the two-body potential phi. The stability and anisotropy of each structure were estimated and compared with the available experimental data.

Karimi, M.↗
NASA NTRS1992

Effects of changes in composite lamina properties on laminate coefficient of thermal expansion

An analytical study of the effects of changes in composite lamina properties on the laminate coefficient of thermal expansion, CTE, has been made. Low modulus graphite/epoxy (T300/934) and high modulus graphite/epoxy (P75/934, P100/934, P120/934), graphite/aluminum (P100/Al), and graphite/glass (HMS/Gl) composite materials were considered in quasi-isotropic and near-zero CTE laminate configurations. The effects of changes in lamina properties on the laminate CTE strongly depend upon the type of composite material as well as the laminate configuration. A 10 percent change in the lamina transverse CTE resulted in changes as large as 0.22 ppm/C in the laminate CTE of a quasi-isotropic Gr/934 laminates. No significant differences were observed in the sensitivities of the laminate CTEs of the P100/934 and P120/934 composite materials due to identical changes in lamina properties. Large changes in laminate CTE can also result from measured temperature and radiation effects on lamina properties.

Tompkins, Stephen S.↗
NASA NTRS1937

The Lateral Instability of Deep Rectangular Beams

Experimental and analytical studies were made of solid and hollow deep rectangular beams to study their lateral instability under various conditions of loading and restraint. The tests were made on bars and tubes of 17ST aluminum alloy. Failure by lateral buckling occurred only in tests on the solid beams. It was found that, within the elastic range, the test results were in agreement with the classical theory for the lateral buckling of deep beams as given by Prandtl, Mitchell, and Timoshenko. The tests were extended to the inelastic range, where it was found that the substitution for Young's modulus of an average modulus of elasticity derived from the stress-strain curve made it possible to predict instability at high stresses.

Dumont, C↗
NASA NTRS1943

Least-work analysis of the problem of shear lag in box beams

The distribution of stress in the cover sheets of thin-wall box beams is analyzed, with regard to the effect of shear deformation in the cover sheets, by the method of least work. Explicit results are obtained for a number of representative cases that show the influence of the following factors on the stress patterns. (1) Variation of stress in spanwise direction as given by elementary beam theory. (2) Value of a parameter called shear-lag aspect ratio which designates the product of span-width ratio of the beam and of the square root of the ratio of effective shear modulus and tensing modulus of the cover sheets. (3) Value of ratio of cover-sheet stiffness to side-web stiffness. (4) Variation of beam height in span direction. (5) Variation of beam width in span direction. (6) Variation of cover-sheet thickness in span direction. General conclusions are drawn from the results obtained. Among them the most important one appears to be the fact that the shear-lag effect depends primarily on the following tow quantities: (1) the value of the shear-lag aspect ratio. (2) the shape of the curve representing the product of the stress of elementary beam theory and of the cover-sheet thickness.

STRESS CALCULATIONS, LEAST-WORK↗
NASA NTRS1939

Tensile elastic properties of 18:8 chromium-nickel steel as affected by plastic deformation

The relationship between stress and strain, and between stress and permanent set, for 18:8 alloy as affected by prior plastic deformation is discussed. Hysteresis and creep and their effects on the stress-strain and stress-set curves are also considered, as well as the influence of duration of the rest interval after cold work and the influence of plastic deformation on proof stresses, on the modulus of elasticity at zero stress, and on the curvature of the stress-strain line. A constant (c sub 1) is suggested to represent the variation of the modulus of elasticity with stress.

Mcadam, D J↗
NASA NTRS1947

Effects of temperature distribution and elastic properties of materials on gas-turbine-disk stresses

Calculations were made to determine the influence of changes in temperature distribution and in elastic material properties on calculated elastic stresses for a typical gas-turbine disk. Severe temperature gradients caused thermal stresses of sufficient magnitude to reduce the operating safety of the disk. Small temperature gradients were found to be desirable because they produced thermal stresses that subtracted from the centrifugal stresses in the region of the rim. The thermal gradients produced a tendency for a severe stress condition to exist near the rim but this stress condition could be shifted away from the region of blade attachment by altering the temperature distribution. The investigation of elastic material properties showed that centrifugal stresses are slightly affected by changes in modulus of elasticity, but that thermal stresses are approximately proportional to modulus of elasticity and to coefficient of thermal expansion.

Holms, Arthur G↗
NASA NTRS1950

The longitudinal stability of elastic swept wings at supersonic speed

The longitudinal stability characteristics of elastic swept wings of high aspect ratio experiencing bending and torsional deformations are calculated for supersonic speed by the application of linearized lifting-surface theory. A parabolic wing deflection curve is assumed and the analysis is simplified by a number of structural approximations. The method is thereby limited in application to wings of high aspect ratio for which the root effects are small. Expressions for the lift, pitching-moment, and span load distribution characteristics are derived in terms of the elastic properties of the wing; namely, the design stress, the modulus of elasticity, the shearing modulus, and the maximum design load factor. The analysis applies to wings with leading edges swept behind the Mach lines. In all cases, however, the trailing edge is sonic or supersonic. Application of the method of analysis to wings with leading edges swept ahead of the Mach lines is discussed.

Frick, C W↗
NASA NTRS1949

Correlation of physical properties of ceramic materials with resistance to fracture by thermal shock

An analysis is made to determine which properties of materials affect their resistance to fracture by thermal stresses.From this analysis, a parameter is evaluated that is correlated with the resistance of ceramic materials to fracture by thermal shock as experimentally determined. This parameter may be used to predict qualitatively the resistance of a material to fracture by thermal shock. Resistance to fracture by thermal shock is shown to be dependent upon the following material properties: thermal conductivity, tensile strength, thermal expansion, and ductility modulus. For qualitative prediction of resistance of materials to fracture by thermal shock, the parameter may be expressed as the product of thermal conductivity and tensile strength divided by the product of linear coefficient of thermal expansion and ductility modulus of the specimen.

Lidman, W G↗
NASA NTRS1930

Riveted joints in thin plates

The method of riveting by forming the closing head under increasing pressure or by a series of hammer blows is investigated. The question as to the best edge distance, i.e. that distance from the rivet center to the plate edge below which it is unadvisable to go and, at the same time useless to go beyond, was examined. The slippage of plates which occurs under the effect of a certain stress, does not completely disappear on unloading. The elastic form change is essentially a function of the elasticity modulus, the slip modulus, the supporting moment, the rivet spacing, etc.

Hilbes, W↗
NASA NTRS1993

Physical and chemical properties of some new perfluoropolyalkylether lubricants prepared by direct fluorination

A series of perfluoropolyalkylether (PFPAE) fluids was synthesized by direct fluorination. Viscosity-temperature properties, oxidation stabilities, oxidation-corrosion properties, bulk modulus, lubricity, surface tension and density were measured. It was shown that as the carbon to oxygen ratio in the polymer repeating unit decreases, the viscometric properties improve, the fluids may become poorer boundary lubricants, the bulk modulus increases, the surface tension increases and the fluid density increases. The presence of difluoromethylene oxide units in the polymer does not significantly lower the oxidation and oxidation-corrosion stabilities as long as the difluoromethylene oxide units are separated by other units.

Jones, W. R., Jr.↗
NASA NTRS1992

Properties of Graphite Fiber Reinforced Copper Matrix Composites for Space Power Applications

The thermal and mechanical properties of pitch-based graphite fiber reinforced copper matrix (Gr/Cu) composites usable for space applications such as radiator fins were investigated. Thermal conductivity was measured as a function of fiber volume fraction and architecture. Results showed for unidirectional P-100 Gr/Cu composites, the longitudinal thermal conductivity was nearly independent of fiber volume fraction. Transverse thermal conductivities (perpendicular to the fibers) were strongly affected by the fiber volume fraction with higher volume fractions resulting in lower thermal conductivities. The effect of architecture on thermal conductivity followed the cosine squared law for simple architectures. Insufficient data are available currently to model more complex architectures, but adding fibers in the direction of the heat flow increases the thermal conductivity as low conductivity plies are supplemented by high conductivity plies. Thermal expansion tests were conducted on the Gr fibers and Gr/Cu composites. The results show a considerable thermal expansion mismatch between the fibers and the Cu matrix. The longitudinal thermal expansion showed a strong dependence on the architecture of the Gr/Cu composites. The composites also show a thermal expansion hysteresis. The hysteresis was eliminated by an engineered interface. Mechanical testing concentrated on the dynamic modulus and strength of the composites. The dynamic modulus of the Gr/Cu composites was 305 GPa up to 400 C, a value equivalent to Be. The strengths of the composites were less than expected, but this is attributed to the poor bond across the interface between the Gr fibers and Cu matrix. Testing of composites with an engineered interface is expected to yield strengths nearer the values predicted by the rule of mixtures.

Ellis, David L.↗
NASA NTRS1994

Non-linear numerical analysis of the Iosipescu specimen for composite materials

A nonlinear elastic finite element analysis is presented of the Iosipescu shear specimen tested in the modified Wyoming fixture for unidirectional graphite/epoxy composites. It is shown that the nonlinear effects due to specimen-to-fixture contact interactions and specimen geometry on the overall shear response are negligible. It is proposed that the tangential shear modulus should be used to characterize the shear resistance of composite materials with highly nonlinear shear response. The correction factors, which are needed to compensate for the nonuniformity of the shear stress or strain distribution in the specimen test section for shear modulus measurement, have to be defined carefully. Strain contours in the nonlinear response ranges are presented and the initiation of failure in the notch regions is investigated.

Ho, Henjen↗
NASA NTRS1994

Variable stiffness torsion springs

In a torsion spring the spring action is a result of the relationships between the torque applied in twisting the spring, the angle through which the torsion spring twists, and the modulus of elasticity of the spring material in shear. Torsion springs employed industrially have been strips, rods, or bars, generally termed shafts, capabable of being flexed by twisting their axes. They rely on the variations in shearing forces to furnish an internal restoring torque. In the torsion springs herein the restoring torque is external and therefore independent of the shearing modulus of elasticity of the torsion spring shaft. Also provided herein is a variable stiffness torsion spring. This torsion spring can be so adjusted as to have a given spring constant. Such variable stiffness torsion springs are extremely useful in gimballed payloads such as sensors, telescopes, and electronic devices on such platforms as a space shuttle or a space station.

Alhorn, Dean C.↗
NASA NTRS1994

New techniques for diffusing-wave spectroscopy

We present two new types of measurements that can be made with diffusing-wave spectroscopy (DWS), a form of dynamic light scattering that applies in limit of strong multiple scattering. The first application is to measure the frequency-dependent linear viscoelastic moduli of complex fluids using light scattering. This is accomplished by measuring the mean square displacement of probe particles using DWS. Their response to thermal fluctuations is determined by the fluctuation-dissipation relation, and is controlled by the response of the surrounding complex fluid. This response can be described in terms of a memory function, which is directly related to the complex elastic modulus of the system. Thus by measuring the mean square displacement, we are able to determine the frequency dependent modulus. The second application is the measurement of shape fluctuations of scattering particles. This is achieved by generalizing the theory for DWS to incorporate the effects if amplitude fluctuations in the scattering intensity of the particles. We apply this new method to study the thermally induced fluctuations in the shape of spherical emulsion droplets whose geometry is controlled by surface tension.

Mason, T. G.↗