Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “microstructure model”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Multiphysics and Multiscale Modeling of Coupled Transport of Chloride Ions in Concrete

Chloride ions (Cl−)-induced corrosion is one of the main degradation mechanisms in reinforced concrete (RC) structures. In most situations, the degradation initiates with the transport of Cl− from the surface of the concrete towards the reinforcing steel. The accumulation of Cl− at the steel-concrete interface could initiate reinforcement corrosion once a threshold Cl− concentration is achieved. An accurate numerical model of the Cl− transport in concrete is required to predict the corrosion initiation in RC structures. However, existing numerical models lack a representation of the heterogenous concrete microstructure resulting from the varying environmental conditions and the indirect effect of time dependent temperature and relative humidity (RH) on the water adsorption and Cl− binding isotherms. In this study, a numerical model is developed to study the coupled transport of Cl− with heat, RH and oxygen (O2) into the concrete. The modeling of the concrete microstructure is performed using the Virtual Cement and Concrete Testing Laboratory (VCCTL) code developed by the U.S. National Institute of Standards and Technology (NIST). The concept of equivalent maturation time is utilized to eliminate the limitation of simulating concrete microstructure using VCCTL in specific environmental conditions such as adiabatic. Thus, a time-dependent concrete microstructure, which depends on the hydration reactions coupled with the temperature and RH of the environment, is achieved to study the Cl− transport. Additionally, Cl− binding isotherms, which are a function of the pH of the concrete pore solution, Cl− concentration, and weight fraction of mono-sulfate aluminate (AFm) and calcium-silicate-hydrate (C-S-H), obtained from an experimental study by the same authors are utilized to account for the Cl− binding of cement hydration products. The temperature dependent RH diffusion was considered to account for the transport of Cl− with moisture transport. The temperature and RH diffusion in the concrete domain, composite theory, and Cl− binding and water adsorption isotherms are used in combination, to estimate the ensuing Cl− diffusion field within the concrete. The coupled transport process of heat, RH, Cl−, and O2 is implemented in the Multiphysics Object-Oriented Simulation Environment (MOOSE) developed by the U.S. Idaho National Laboratory (INL). The model was verified and validated using data from multiple experimental studies with different concrete mixture proportions, curing durations, and environmental conditions. Additionally, a sensitivity analysis was performed to identify that the water-to-cement (w/c) ratio, the exposure duration, the boundary conditions: temperature, RH, surface Cl− concentration, Cl− diffusion coefficient in the capillary water, and the critical RH are the important parameters that govern the Cl− transport in RC structures. In a case study, the capabilities of the developed numerical model are demonstrated by studying the complex 2D diffusion of Cl− in a RC beam located in two different climatic regions: warm and humid weather in Galveston, Texas, and cold and dry weather in North Minnesota, Minnesota, subjected to time varying temperature, RH, and surface Cl− concentrations.

composite theory↗

A Discussion of Strength Reduction Factor Development for Thermal Aging Effect on Nuclear Structural Alloys

In consideration of structural alloy property deterioration during long-term exposure to elevated temperatures, the yield and ultimate tensile strength reduction factors are provided in the Boiler and Pressure Vessel Code Section III for nuclear reactor component design and operation analysis. Because the Gen IV reactor requirement of 40 ~ 60 years of service life makes it difficult to acquire such long exposure test data for developing the reduction factors, they must be derived from test data with relatively short exposure by predictive methods considered to be reasonably reliable. A novel approach with a physically-based model has recently been proposed for application to development of reduction factors for 9Cr-1Mo-V. In the model, contributors to the tensile strength are first identified and related to definite microstructural features of the alloy, then some physically-based methods are employed to simulate the microstructural evolution, and finally the model is assembled with test-data-calibrated parameters to generate the yield and ultimate tensile strength reduction factors covering elevated temperature exposure for up to 57 years. The approach is undoubtedly a trailblazing development that will, if proven reliable, lead to a paradigm shift in predicting thermal aging behavior of many other alloys. Its debut application to Section III, however, concerns nuclear safety and naturally warrants objective, impartial, and thorough technical scrutiny. In the present paper, the novel and conventional approaches are discussed. Necessary improvements to the novel approach are recommended for its application to nuclear structural component design and analysis, and for its potential expanded use to other alloys.

Ren, Weiju↗

Characterization and Modeling of Deformation Induced Damage in Titanium Alloys

Over the lifetime of their DOE support, and specifically during the past funding cycle, the PIs have primarily focused on ambient temperature studies of the mechanisms of heterogeneous deformation and shear transfer at GBs. The PIs have developed and applied a broad array of experimental approaches complemented by advanced computational methods and simulations to enable new understanding of GB shear transfer, and a new approach for modeling this behavior at the mechanistic level has been established. The PIs have examined how slip behavior differs on the surface and interior of polycrystals using a variety of approaches. Some of the associated data has been used to generate 3-D models of experimentally-characterized microstructures that both support interpretation of deformation mechanisms as well as reveal where modeling needs to be improved to more closely agree with what is experimentally observed. The PIs progress in constitutive modeling of crystal plasticity has introduced explicit GB resistance to shear that depends on the mutual geometry of active slip systems. This past work places the PIs in a good position to take on the challenges associated with mechanistically understanding the interplay between GBS and slip interactions.

42 ENGINEERING↗

Li-ion battery design through microstructural optimization using generative AI

Lithium-ion batteries are used across various applications, necessitating tailored cell designs to enhance performance. Optimizing electrode manufacturing parameters is a key route to achieving this, as these parameters directly influence the microstructure and performance of the cells. However, linking process parameters to performance is complex, and experimental or modeling campaigns are often slow and expensive. This study introduces a fast computational optimization framework for electrode manufacturing parameters. A generative model, trained on a small dataset of microstructural images associated with different manufacturing parameters, efficiently generates representative microstructures for new parameters. This model is integrated into a Bayesian optimization loop that includes microstructure generation, characterization, and simulation, aiming to find optimal manufacturing parameters for a particular application. Significant improvement in the energy density of a 4680 cell is achieved through bespoke cell design, highlighting the importance of cell-scale normalization. The framework’s modularity allows its application to various advanced materials manufacturing scenarios.

batteries↗

A phase-field model of quasi-brittle fracture for pressurized cracks: Application to UO 2 high-burnup microstructure fragmentation

Here, in this paper, we present a phase-field model of quasi-brittle fracture with pressurized cracks, with dedicated applications for polycrystalline materials. The model is formulated as a minimization problem within the variational framework. The external work done by pressure on the crack surfaces is included in the objective function. Several careful modeling choices lead to a regularization-length-independent critical strength. The model is constructed to give a softening response with an underlying linear traction-separation law. The pressure-dependent softening response and the regularization of the prescribed pressure are demonstrated with a (quasi) one-dimensional numerical analysis. In a two-dimensional numerical analysis under plane strain assumptions, the critical stress corresponding to crack propagation (as predicted by our quasi-brittle fracture model) is compared with linear elastic fracture mechanics (LEFM) analytical solutions. Our model is further utilized to simulate fission-gas-induced fragmentation of the UO 2 high-burnup structure (HBS). Simulation results show that pressurized bubbles can cause crack nucleation and propagation, and that the bubble size and the surrounding external pressure affect the critical pressure corresponding to crack nucleation. Simulations of a partial HBS at different recrystallization stages show that different grain structures (due to recrystallization) also influence crack paths and fragmentation morphology.

36 MATERIALS SCIENCE↗

A Simplified Micromechanical Modeling Approach to Predict the Tensile Flow Curve Behavior of Dual-Phase Steels

Micromechanical modeling is used to predict material’s tensile flow curve behavior based on microstructural characteristics. This research develops a simplified micromechanical modeling approach for predicting flow curve behavior of dual-phase steels. The existing literature reports on two broad approaches for determining tensile flow curve of these steels. The modeling approach developed in this work attempts to overcome specific limitations of the existing two approaches. This approach combines dislocation-based strain-hardening method with rule of mixtures. In the first step of modeling, ‘dislocation-based strain-hardening method’ was employed to predict tensile behavior of individual phases of ferrite and martensite. In the second step, the individual flow curves were combined using ‘rule of mixtures,’ to obtain the composite dual-phase flow behavior. To check accuracy of proposed model, four distinct dual-phase microstructures comprising of different ferrite grain size, martensite fraction, and carbon content in martensite were processed by annealing experiments. The true stress–strain curves for various microstructures were predicted with the newly developed micromechanical model. The results of micromechanical model matched closely with those of actual tensile tests. Thus, this micromechanical modeling approach can be used to predict and optimize the tensile flow behavior of dual-phase steels.

36 MATERIALS SCIENCE↗

Phase-field simulations of fission gas bubbles in high burnup UO2 during steady-state and LOCA transient conditions

To improve the economics of commercial nuclear energy generation, U.S. utilities are currently seeking licensing approval to operate UO2 fuel to higher burnups. One significant safety issue that must be addressed to obtain approval is the potential for fine fragmentation/pulverization of the fuel during a loss-of-coolant accident (LOCA). It has been hypothesized this is caused by the rapid increase of pressure in fission gas bubbles in the high burnup region of the fuel. To better understand this phenomenon, a novel phase-field model of the fission gas bubble microstructure in UO2 has been developed and implemented in Idaho National Laboratory's Marmot application for phase-field simulation of nuclear materials. Simulations of bubble growth in the high burnup region during steady-state conditions showed that initially overpressurized bubbles decreased in pressure during growth, but still remained above equilibrium pressure. During a LOCA transient, simulations of bubbles in the high burnup region showed that bubble size did not change significantly, and the pressure increase due to the transient was calculated and passed to a phase-field model of fracture.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

A Rate Theory Model of Radiation-Induced Swelling in an Austenitic Stainless Steel

Many rate theory models of cavity (void) swelling have been published over the past 50 years, all having the same, or similar, structures. A rigorous validation of the models has not been possible because of the dearth of information concerning the microstructures that correspond with the swelling data. Whereas the lack of microstructure information is still an issue for historical swelling data, in the past 10–20 years data have been published on the evolution of the microstructure (point defect yields from collision cascades, cavity number densities, and dislocation densities/yield strengths) allowing certain gaps in information to be filled when considering historic swelling data. With reasonable estimates of key microstructure parameters, a standard rate theory model can be applied, and the model parameter space explored, in connection with historical swelling data. By using published data on: (i) yield strength as a function of dose and temperature (to establish an empirical expression for dislocation density evolution); (ii) cavity number densities as a function of temperature; and (iii) freely migrating defect (FMD) production as a function of primary knock-on atom (PKA) spectrum, the necessary parameter and microstructure inputs that were previously unknown can be used in model development. This paper describes a rate-theory model for void swelling of 316 stainless steel irradiated in the EBR-2 reactor as a function of irradiation temperature and neutron dose.

36 MATERIALS SCIENCE↗

A Comparative Study of Constitutive Characteristics and Microstructure Evolution between Uniaxial and Plane Strain Compression of an AA6061 Alloy

The hot deformation behavior of an AA6061 alloy was comparatively studied by uniaxial compression (UC) and plane strain compression (PSC) in the temperature range of 300-450 °C and strain rate range of 0.01-5 s{sup −1}. The processing maps were constructed based on a dynamic materials model, and the associated microstructures were observed. Under the same deformation conditions, the flow stress of the AA6061 alloy during PSC is higher than that during UC, which can be characterized by the Zener–Hollomon (Z) parameter in a hyperbolic sine-type equation with an activation energy Q of 175.2 kJ mol{sup −1} and 201.9 kJ mol{sup −1}, respectively. In addition, the instability domain is narrower under PSC compared to that under UC. The observed microstructures also indicate that as the Z value decreases, the tendency of dynamic recrystallization increases during PSC. The softening mechanisms in the AA6061 alloy after PSC and UC mainly consist of the dynamic recovery that is accompanied by a slight dynamic recrystallization. The optimum parameters are in the temperature range of 360-450 °C and strain rate range of 0.03-0.3 s{sup −1} for UC, and for PSC, the optimum parameters are in the temperature range of 320-400 °C and strain rate range of 0.01-0.05 s{sup −1}.

36 MATERIALS SCIENCE↗

Improving Additive Manufactured Component Performance through Multi-Scale Microstructure Simulation and Process Optimization

The purpose of this project was to utilize computational tools to understand the relationships between processing, microstructure, and properties for additively manufactured (AM) aluminum alloys for automotive applications, and to provide an engineering solution for helping to optimize process conditions. The project leverages ORNL developments in computational modeling, including AM process modeling, phase-field based microstructure evolution predictions, and data analytics techniques for mapping process conditions to material outcomes. The project utilized an Al-Cu-Mn-Zr alloy as a model material for studying formation of defects and microstructural features in response to variations in process conditions. Based on both pre-existing experimental data and simulation results, statistical process maps were constructed to identify regions of process space with minimal defect formation and advantageous microstructures and properties. The software tools used for this purpose were successful disseminated to GM, who were able to successful compile the relevant HPC codes within their own computing ecosystem and perform initial calculations to reproduce ORNL results.

36 MATERIALS SCIENCE↗

TAOI B- Computational Microstructural Optimization Design Tool for High Temperature Structural Materials

The objectives of this research were two-fold: (a) develop a methodology for microstructural optimization of alloys - genetic algorithm approach for alloy microstructural optimization using theoretical models based on fundamental micro-mechanisms, and (b) develop a new computationally designed Ni-Cr alloy for coal-fired power plant applications. The broader outcome of these objectives is expected to be creation of an integrated approach for ‘structural materials by microstructural design’. Three alloy systems were considered for computational optimization and validation, (i) Ni-20Cr (wt.%) base alloy using only solid solution strengthening, (ii) nano-Y 2 O 3 containing Ni-20Cr-1.2Y 2 O 3 (wt.%) alloy for dispersion strengthening and (iii) a sub-micron Al 2 O 3 for composite strengthening, Ni-20Cr-1.2Y 2 O 3 -5.0Al 2 O 3 (wt.%). The specimens were synthesized by mechanical alloying and consolidated using spark plasma sintering. Detailed microstructural characterization was done along with initial mechanical properties to validate the computational prediction. A key target property is to have creep rate of 1x10 -9 s -1 at 100 MPa and 800°C. The initial results were quite promising and require additional quantification of strengthening contributions from dislocation-particle attractive interaction and load transfer. The observed creep rate was in order of 10 -9 s -1 for longer time creep test of Ni-20Cr -1.2Y 2 O 3 -5Al 2 O 3 , lending support to the overall approach pursued in this project.

36 MATERIALS SCIENCE↗

Applying neutron transmission physics and 3D statistical full-field model to understand 2D Bragg-edge imaging

Bragg-edge imaging, which is also known as neutron radiography, has recently emerged as a novel crystalline characterization technique. Modelling of this novel technique by incorporating various features of the underlying microstructure (including the crystallographic texture, the morphological texture, and the grain size) of the material remains a subject of considerable research and development. In this paper, Inconel 718 samples made by additive manufacturing were investigated by neutron diffraction and neutron radiography techniques. The specimen features strong morphological and crystallographic textures and a highly heterogeneous microstructure. A 3D statistical full-field model is introduced by taking details of the microstructure into account to understand the experimental neutron radiography results. The Bragg-edge imaging and the total cross section were calculated based on the neutron transmission physics. A good match was obtained between the model predictions and experimental results at different incident beam angles with respect to the sample build direction. The current theoretical approach has the ability to incorporate 3D spatially resolved microstructural heterogeneity information and shows promise in understanding the 2D neutron radiography of bulk samples. With further development to incorporate the heterogeneity in lattice strain in the model, it can be used as a powerful tool in the future to better understand the neutron radiography data.

72 PHYSICS OF ELEMENTARY PARTICLES AND FIELDS↗

Update on INSIGHTS Development

INSIGHTS is a transformational separate effects testing capability to perform in situ irradiation studies and characterization of the microscale behavior of nuclear fuel materials under a wide variety of in-pile conditions. Separate effects testing including growth, irradiation, and monitoring of these materials, and encompasses the full science based approach for fuels development from the nanoscale to the mesoscale behavior of the sample material and other defects driven by the modeling and simulation efforts of INL.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Radiation-induced Swelling and Microcracking in SiC Cladding for LWRs

After the Fukushima accident in 2011, SiC has attracted considerable attention as a potential material for fuel cladding that can offer increased accident tolerance in light water reactors (LWRs) compared to zircaloy cladding. Existing measurements on nuclear grade SiC/SiC composites made of high-purity, stoichiometric SiC have already shown very good radiation tolerance in various harsh environments. However, there are a number of challenges that need to be addressed before SiC composites can be successfully used in LWR technologies. One of them is irradiation-induced swelling, which can lead to development of significant stresses in the matrix, followed by microcracking and subsequent release of fission products. Models of irradiation-induced swelling had been largely empirical and therefore they cannot be used to predict the microstructural dependence of microcracking. Existing models are also limited by the lack of understanding of defects that form due to irradiation in the range of temperatures relevant to fuel cladding in LWRs (<1000°C). Many of the defects in this regime of temperature are too small to be detected with traditional transmission electron microscopy (TEM) techniques. In fact the defects observed in traditional TEM account only for 10-45% of the swelling measured in irradiated SiC. Here, we developed a multi-scale simulation methodology combined with state of the art experimental imaging techniques based on aberration corrected scanning transmission electron microscopy (STEM) to provide a scientific basis for predictive models of radiation swelling and microcracking in SiC. Specifically, we have developed a phase field fracture model that predicts microcrack initiation and growth in polycrystalline SiC. The model accounts for single crystal anisotropy, including anisotropy in the elastic constants and anisotropic surface energy. It also considers the reduced fracture strength of grain boundaries. The model was implemented using the MARMOT mesoscale nuclear materials tool. We have parameterized the model for SiC using molecular dynamics simulation results. The model has been verified using single crystal, bicrystal, and polycrystal examples. Swelling model has also been developed based on cluster dynamics simulations of defect evolution in SiC. We found that point defects and small defect clusters have a significant contribution to swelling. This finding is important because point defects and very small defect clusters are not visible in experiments (e.g., in TEM). Combined modeling and experiments can bring critical insights into how swelling depends on irradiation conditions and the microstructure. In situ nanoindentation tests and ex situ nanoindentation tests were performed on assynthesized 3C-SiC and 3C-SiC irradiated under different radiation conditions. Without radiation, bend contour movement and residual bend contours after indentation demonstrate some room temperature plastic flow and residual plastic deformation. Plastic deformation recovery is also observed on unirradiated samples during unloading. Radiation-induced embrittlement is demonstrated by differences in crack geometry in in situ tests, and is consistent with ex situ test results. Failure by single, straight, cracks indicates decreased fracture toughness due to irradiation in 3C-SiC. Future work includes coupling of the swelling and fracture models and development of a master equation that can be used in the BISON code.

11 NUCLEAR FUEL CYCLE AND FUEL MATERIALS↗

Phase field modelling of stressed grain growth: Analytical study and the effect of microstructural length scale

We establish the correlation between the diffuse interface and sharp interface descriptions for stressed grain boundary migration by presenting analytical solutions for stressed migration of a circular grain boundary in a bicrystalline phase field domain. The validity and accuracy of the phase field model is investigated by comparing the phase field simulation results against analytical solutions. The phase field model can reproduce precise boundary kinetics and stress evolution provided that a thermodynamically consistent theory and proper expressions for model parameters in terms of physical material properties are employed. Quantitative phase field simulations are then employed to investigate the effect of microstructural length scale on microstructure and texture evolution by stressed grain growth in an elastically deformed polycrystalline aggregate. The simulation results reveal a transitional behaviour from normal to abnormal grain growth by increasing the microstructural length scale.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗

Diffuse-Interface Model for Smoothed Particle Hydrodynamics

Diffuse-interface theory provides a foundation for the modeling and simulation of microstructure evolution in a very wide range of materials, and for the tracking/capturing of dynamic interfaces between different materials on larger scales. Smoothed particle hydrodynamics (SPH) is also widely used to simulate fluids and solids that are subjected to large deformations and have complex dynamic boundaries and/or interfaces, but no explicit interface tracking/capturing is required, even when topological changes such as fragmentation and coalescence occur, because of its Lagrangian particle nature. Here we developed an SPH model for two component single phase fluids that is based on diffuse-interface theory. In the model, the interface has a finite thickness and a surface tension that depend on the coefficient, k, of the gradient contribution to the Helmholtz free energy functional and the density dependent homogeneous free energy. In this model, there is no need to locate the surface (or interface) or to compute the curvature at and near the interface. One- and two-dimensional SPH simulations were used to validate the model.

71 CLASSICAL AND QUANTUM MECHANICS, GENERAL PHYSIC↗

Understanding structure-processing relationships in metal additive manufacturing via featurization of microstructural images

Understanding and predicting accurate property-structure-processing relationships for additively manufactured components is important for both forward and inverse design of robust, reliable parts and assemblies. While direct mapping of process parameters to properties is sometimes plausible, it is often rendered difficult due to poor microstructural control. Exploring the direct relationship between processing conditions and microstructural features can thus provide significant physical insights and aid the overall design process. Here, in this study, we develop an automated high-throughput framework to simulate an uncertainty-aware additive manufacturing (AM) process, characterize microstructural images, and extract meaningful features/descriptors. A kinetic Monte Carlo (KMC) based model of the AM process is used to simulate microstructural evolution for a diverse set of experimentally relevant processing conditions. We perform a parametric study to explore the relationship between microstructural features and processing conditions. Our results indicate that a many-to-one mapping can exist between processing conditions and typical descriptors; therefore, multiple descriptors are thus necessary to unambiguously represent microstructural images. Our work provides crucial quantitative and qualitative in-formation that would aid in the selection of features for microstructural images. Featurized microstructures could then be utilized to build data-driven models for predictive control of microstructures and thereby properties of additively manufactured components.

36 MATERIALS SCIENCE↗