Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “materials aging”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

Effects of proton irradiation on nanocluster precipitation in ferritic steel containing fcc alloying additions

Newly-developed precipitate-strengthened ferritic steels with and without pre-existing nanoscale precipitates were irradiated with 4 MeV protons to a dose of ~5 mdpa at 50 C and subsequently examined by nanoindentation and atom probe tomography (APT). Irradiation-enhanced precipitation and coarsening of pre-existing nanoscale precipitates were observed. Copper partitions to the precipitate core along with a segregation of Ni, Al and Mn to the precipitate/matrix interface after both thermal aging and proton irradiation. Proton irradiation induces the precipitation reaction and coarsening of pre-existing nanoscale precipitates, and these results are similar to a thermal aging process. The precipitation and coarsening of nanoscale precipitates are responsible for the changes in hardness. The observation of the radiation-induced softening is essentially due to the coarsening of the pre-existing Cu-rich nanoscale precipitates. The implication of the precipitation on the embrittlement of reactor-pressure-vessel steels after irradiation is discussed.

Zhang, Zhongwu↗

Anelastic anomalies and negative Poisson's ratio in tetragonal BaTiO{sub 3} ceramics

Anelastic anomalies (sharp variations in modulus and damping with temperature) were observed in tetragonal BaTiO{sub 3} via broadband viscoelastic spectroscopy after aging at 50 deg. C for 15 h. The effect was most pronounced under electrical short circuit condition, at low frequency and under small excitation strain (10{sup -6}). Softening in bulk modulus and negative Poisson's ratio were observed near 60 deg. C. Effects are attributed to an oxygen vacancy mechanism. A relaxational model cannot account for sharp response at smaller strains. Heterogeneity of negative stiffness is considered as a cause.

36 MATERIALS SCIENCE↗

Structure of the lamin A/C R482W mutant responsible for dominant familial partial lipodystrophy (FPLD)

Proteins of the A-type lamin family, which consists of two members, lamin A and lamin C, are the major components of a thin proteinaceous filamentous meshwork, the lamina, that underlies the inner nuclear membrane. A-type lamins have recently become the focus of extensive functional studies as a consequence of the linking of at least eight congenital diseases to mutations in the lamin A/C gene (LMNA). This spectrum of pathologies, which mostly manifest themselves as dominant traits, includes muscle dystrophies, dilated cardiomyopathies, the premature aging syndrome Hutchinson-Guilford progeria and familial partial lipodystrophy (FPLD). The crystal structure of the lamin A/C mutant R482W, a variant that causes FPLD, has been determined at 1.5 {angstrom} resolution. A completely novel aggregation state of the C-terminal globular domain and the position of the mutated amino-acid residue suggest means by which the mutation may affect lamin A/C-protein and protein-DNA interactions.

36 MATERIALS SCIENCE↗

Characterization of intermetallic precipitates in a Nimonic alloy by ultrasonic velocity measurements

Ultrasonic velocity measurements have been carried out in Nimonic 263 specimens thermally aged at 923 and 1073 K for durations up to 75 h and correlated with the results of hardness measurements and electron microscopy studies. The ultrasonic velocities and hardness results obtained in the specimens thermally aged at both temperatures clearly indicated that ultrasonic velocity is more sensitive to the initiation of the precipitation, whereas the influence of precipitation on hardness can be observed only after the precipitates attain a minimum size to influence the movement of dislocations. Further, ultrasonic velocity measurements also revealed faster kinetics and a lesser amount of precipitation at 1073 K compared to 923 K due to higher solubility of precipitate-forming elements.

36 MATERIALS SCIENCE↗

The 3.3 micron feature, H2, and ionized gas in the Orion bar

The results of spectroscopy of the 3.3 micron feature, H2 emission, P-alpha, and Br-alpha, obtained along a line perpendicular to the Orion ionization front, are presented. The intensity of the 3.3 micron feature reaches a maximum between the ionization front and the H2 peak. The 3.33 micron spatial distribution appears to be due to destruction of the emitting material within the H II region and extinction of the exciting radiation between the edge of the H II region and the H2 peak, resulting in a maximum between the ionization front and the H2 peak. The H2 peak is consistent with either being due to a shock front or being due to UV-pumped fluorescence from dense clumps of H2. The width of the 3.3 micron feature observed at high spectral resolution is constant in regions of varying UV flux. It is suggested that the strength of the UV field is not the cause of the variations in the 3.3 micron feature width observed in other sources, but rather that these variations are caused by a compositional change related to the age of the emitting material.

Sellgren, K.↗

Grain boundary precipitation phenomena in an alloy 33 (Cr-Fe-Ni-N) subjected to direct-aging treatments (700 °C and 900 °C)

Highlights: • Complex GB precipitation occurs in Alloy 33 upon aging at 700 °C: conventional and DP modes. At 900 °C only the former occurs. • Two types of DP colonies were observed at 700 °C: unidirectional/parallel and multidirectional/irregular precipitates. • X-ray micro analyses reveal that irregular DP products develop more than one precipitate phase within the same DP colony. - Abstract: Precipitation behavior of alloy 33 upon isothermally aging at 700 °C and at 900 °C was studied by scanning electron microscopy (SEM), transmission electron microscopy (TEM) and X-ray energy dispersive spectroscopy (XEDS). The name, alloy 33, reflects the quasi-equal atomic content of the base elements Fe, Ni and Cr close to 33%, with the addition of Mo and N. The most remarkable features of the microstructural evolution resulting from the aging heat treatments are described as follows: aging at 700 °C leads to homogeneous and heterogeneous grain boundary precipitation, where the discontinuous mode is dominant at this temperature. Conversely, the opposite behavior was observed when the alloy is aged at 900 °C: predominantly homogeneous precipitation together with grain boundary precipitation, however with rare evidence for discontinuous precipitation (DP), even after longer aging times. In the present study, the topology and content of the DP colonies generated by the combined effect of grain boundary migration diffusion and precipitation under isothermal aging at 700 °C were particularly investigated. A variety of morphological features were observed: mainly (1) classical-type microstructure with straight and parallel lamellar precipitates with regular interlamellar spacing and (2) another microstructure with irregular and complex DP colonies. According to our analytical electron microscopy observations, the latter shows that there are more than one precipitate phase within the same colony, which is new to the current theory and experimental evidence on this subject.

36 MATERIALS SCIENCE↗

Sigma phase evolution and nucleation mechanisms revealed by atom probe tomography in a 347H stainless steel

The size evolution and phase composition of sigma phases were investigated for a 347H stainless steel subject to isothermal aging at 750 °C for up to 10,000 h. Scanning electron microscopy reveals that sigma phases are present before 336 h aging and they continue to grow for all aging times studied. Atom probe tomography shows little variation in the sigma phase composition with aging time up to 10,000 h, and only the C content decreases with aging time. The comparison of C concentration suggests that the sigma phase does not nucleate within the C-depleted matrix or precipitate free grain boundaries, leaving dissolving metastable M 23 C 6 as the only possible nucleation site. Based on the experimental results and thermodynamic simulations, the desirable Nb concentration is discussed to reduce the kinetics of sigma phase growth, and possible design directions are suggested to improve 347H.

36 MATERIALS SCIENCE↗

High Resolution Characterization of the Precipitation Behavior of an Al-Zn-Mg-Cu alloy

The metastable particles in an Al-Zn-Mg-Cu alloy have been examined at atomic-resolution using high-angle annular dark field (HAADF) imaging. In underaged conditions, thin {eta}' plates were formed with a thickness of 7 atomic planes parallel to the {l_brace}111{r_brace}Al planes. The five inner planes of the {eta}' phase appear to be alternatively enriched in Mg and Zn, with two outer planes forming distinct Zn-rich interfacial planes. Similar Zn rich interfacial enrichment has also been identified for the {eta} phase, which is a minimum 11-planes thick structure. In rare instances, particles less than 7 planes were found indicating a very early preference for 7-layer particle formation. Throughout the aging, the plate thickness appears constant, while the plate radius increases and no particles between 7 and 11 planes were observed. Based on the HAADF contrast, our observations do not support the {eta}' models previously set forth by other authors. Clear structural similarities between {eta}' and {eta} were observed, suggesting that drawing distinctions between {eta}' and {eta} phases may not be necessary or useful.

36 MATERIALS SCIENCE↗

A facile electron microscopy method for measuring precipitate volume fractions in AlCuMg alloys

Precipitate volume fraction is an important parameter to estimate the strength of precipitation-hardened metals. In this study, a facile method was applied to measure the precipitate volume fractions in an age-hardened AlCuMg alloy. In this method, the precipitate volume fraction values can be obtained by multiplying the volume precipitate number densities with the averaged precipitate volumes, which can be easily measured in scanning electron microscopy and transmission electron microscopy, respectively. Compared with the conventional method, in which the specimen thickness has to be measured in transmission electron microscopy, the method proposed in this study is more facile to perform. - Highlights: Black-Right-Pointing-Pointer We have proposed a facile method to measure precipitate volume fractions for precipitation-hardened metals. Black-Right-Pointing-Pointer This technique works well for the square-shaped {theta} Prime -phase nano-precipitates in 2xxx aluminum alloys. Black-Right-Pointing-Pointer Interesting is that the proposed method is easy for materials scientists and engineers to perform.

36 MATERIALS SCIENCE↗

Microstructure and Hardness Evolution in Haynes 282 Nickel-Based Superalloy During Multi-variant Aging Heat Treatment

In this paper, the effect of applied multi-variant heat treatment on microstructure, phase composition and mechanical response of Haynes 282 nickel-based superalloy was investigated. For this reason, temperatures of both stages of standard two-stage aging treatment (i.e., 1010 °C/2 h + 780 °C/8 h) were extended to 900-1100 °C/2 h and 680-880 °C/8 h ranges, respectively. Consequently, 30 different variants of heat treatment were applied. The microstructural features of heat-treated samples were investigated by means of light microscopy and SEM/EDS methods, while mechanical properties were examined via microhardness measurements. It was found that by using various combinations of temperatures of the first and second stage of aging, the room temperature hardness of Haynes 282 alloy can be decreased by ~ 100 HV units or increased by up to 25 HV units as compared to that of the alloy subjected to the standard heat treatment schedule. The mechanical response of the alloy is determined by a complex structural evolution involving the secondary precipitation of γ′, M{sub 23}C{sub 6} and M{sub 6}C phases, as well as their interaction with the fcc γ matrix.

36 MATERIALS SCIENCE↗

Direct comparison of Fe-Cr unmixing characterization by atom probe tomography and small angle scattering

The fine microstructure obtained by unmixing of a solid solution either by classical precipitation or spinodal decomposition is often characterized either by small angle scattering or atom probe tomography. This article shows that a common data analysis framework can be used to analyze data obtained from these two techniques. An example of the application of this common analysis is given for characterization of the unmixing of the Fe-Cr matrix of a 15-5 PH stainless steel during long-term ageing at 350 °C and 400 °C. A direct comparison of the Cr composition fluctuations amplitudes and characteristic lengths obtained with both techniques is made showing a quantitative agreement for the fluctuation amplitudes. The origin of the discrepancy remaining for the characteristic lengths is discussed. - Highlights: •Common analysis framework for atom probe tomography and small angle scattering •Comparison of same microstructural characteristics obtained using both techniques •Good correlation of Cr composition fluctuations amplitudes from both techniques •Good correlation of Cr composition fluctuations amplitudes with classic V parameter.

36 MATERIALS SCIENCE↗

Effects of Ag addition on solid–state interfacial reactions between Sn–Ag–Cu solder and Cu substrate

Low–Ag–content Sn–Ag–Cu (SAC) solders have attracted much recent attention in electronic packaging for their low cost. To reasonably reduce the Ag content in Pb–free solders, a deep understanding of the basic influence of Ag on the SAC solder/Cu substrate interfacial reaction is essential. Previous studies have discussed the influence of Ag on the interfacial intermetallic compound (IMC) thickness. However, because IMC growth is the joint result of multiple factors, such characterizations do not reveal the actual role of Ag. In this study, changes in interfacial IMCs after Ag introduction were systemically and quantitatively characterized in terms of coarsening behaviors, orientation evolution, and growth kinetics. The results show that Ag in the solder alloy affects the coarsening behavior, accelerates the orientation concentration, and inhibits the growth of interfacial IMCs during solid–state aging. The inhibition mechanism was quantitatively discussed considering the individual diffusion behaviors of Cu and Sn atoms, revealing that Ag inhibits interfacial IMC growth primarily by slowing the diffusion of Cu atoms through the interface. - Highlights: •Role of Ag in IMC formation during Sn–Ag–Cu soldering was investigated. •Ag affects coarsening, crystallographic orientation, and IMC growth. •Diffusion pathways of Sn and Cu are affected differently by Ag. •Ag slows Cu diffusion to inhibit IMC growth at solder/substrate interface.

36 MATERIALS SCIENCE↗

Constitutive modeling for isotropic materials (HOST)

The results of the third year of work on a program which is part of the NASA Hot Section Technology program (HOST) are presented. The goals of this program are: (1) the development of unified constitutive models for rate dependent isotropic materials; and (2) the demonstration of the use of unified models in structural analyses of hot section components of gas turbine engines. The unified models selected for development and evaluation are those of Bodner-Partom and of Walker. A test procedure was developed for assisting the generation of a data base for the Bodner-Partom model using a relatively small number of specimens. This test procedure involved performing a tensile test at a temperature of interest that involves a succession of strain-rate changes. The results for B1900+Hf indicate that material constants related to hardening and thermal recovery can be obtained on the basis of such a procedure. Strain aging, thermal recovery, and unexpected material variations, however, preluded an accurate determination of the strain-rate sensitivity parameter is this exercise. The effects of casting grain size on the constitutive behavior of B1900+Hf were studied and no particular grain size effect was observed. A systematic procedure was also developed for determining the material constants in the Bodner-Partom model. Both the new test procedure and the method for determining material constants were applied to the alternate material, Mar-M247 . Test data including tensile, creep, cyclic and nonproportional biaxial (tension/torsion) loading were collected. Good correlations were obtained between the Bodner-Partom model and experiments. A literature survey was conducted to assess the effects of thermal history on the constitutive behavior of metals. Thermal history effects are expected to be present at temperature regimes where strain aging and change of microstructure are important. Possible modifications to the Bodner-Partom model to account for these effects are outlined. The use of a unified constitutive model for hot section component analyses was demonstrated by applying the Walker model and the MARC finite-element code to a B1900+Hf airfoil problem.

Chan, Kwai S.↗

Hydrothermal Synthesis and Analysis of Iodine-Containing Sodalite - 16153

Five process variables affecting hydrothermal synthesis of iodide sodalite, Na{sub 8}Al{sub 6}Si{sub 6}O{sub 24}I{sub 2}, were investigated, including NaOH concentration, aging time, temperature, Al/Si ratio, and precursor concentration. X-ray powder diffraction was performed to characterize synthesized samples, and Rietveld refinement method was used to quantify the mass fractions of phases. Iodide sodalite yield increased, in general, as NaOH concentration, aging time, and temperature increased. Lowering the Al/Si ratio from 1 to 0.5 increased the formation of cancrinite. Diluting the precursor concentration in the mixed solution with water revealed that nepheline hydrate-1, a zeolite, formed rather than sodalite. This observation, along with the preferential formation of zeolite A in samples where no NaOH was added, suggests that mechanisms for transport of the ions and formation of the aluminosilicate frameworks vary with hydrothermal conditions. The model for the best synthesis conditions based on the four significant variables is presented. (authors)

36 MATERIALS SCIENCE↗

Solutionization via Severe Plastic Deformation: Effect on Natural Aging in an Al-Mg-Si-(Mn) Alloy

Shear Assisted Processing and Extrusion (ShAPE), a severe plastic deformation technique that is fast and scalable, was used to produce thin-wall tubing from alloy 6082 (Al-0.8Mg-0.9Si-0.7Mn) with in-situ solutionization during processing quickly followed by quenching. Quench medium and input material heat treatment were varied and natural aging behavior (T1 heat treatment) was evaluated using tensile testing. As-cast input material was found to have higher strength early in post-ShAPE natural aging and homogenized input material was found to have strengthening during natural aging. Compared to air quenching, water quenching gave greater strength both early in and after natural aging. These observations along with microscopy suggest that: 1. air quenching was too slow; 2. as-cast material was not fully solutionized but plastic deformation broke up the coarse intermetallic particles, which provided strengthening; and 3. homogenized material was solutionized well, which led to good natural aging behavior.

Milligan, Brian K.↗

Pressure effects on phase equilibria and solid solubility in MgO-Y2O3 nanocomposites

We study the temperature and pressure dependence of phase evolution in the 0.5MgO-0.5Y{sub 2}O{sub 3} nanocomposite system using a diamond anvil apparatus in conjunction with in situ synchrotron energy dispersive x-ray diffraction at 7 GPa hydrostatic pressure. At (298 K, 7.0 GPa), structural transformations in the Y{sub 2}O{sub 3} phase are observed, giving rise to the co-existence of its cubic, hexagonal, and monoclinic polymorphs together with cubic MgO. An increase in temperature to 1273 K causes the crystallinity of the Y{sub 2}O{sub 3} hexagonal and monoclinic phases to increase. Isothermal and isobaric hold at (1273 K, 7.0 GPa) for 60 min results in yttrium dissolution in cubic MgO, causing {approx}1.0% expansive volumetric lattice strain despite the large differences in the ionic radii of the cations. Cooling the nanocomposite to (298 K, 0 GPa) after a 60 min soak yields four phase co-existence among cubic MgO and cubic, hexagonal, and monoclinic Y{sub 2}O{sub 3}. The residual MgO unit cell volume expansion is 0.69% at 298 K, indicating solid solution formation at room temperature despite large differences in the ionic radii of Mg{sup 2+} and Y{sup 3+}. The macroscopic shrinkage due to densification is 3% by volume. Thermodynamic considerations suggest that the relative molar partial volume of Y{sup 3+} in MgO is a negative quantity, indicating that the partial molar volume of Y{sup 3+} in the solid solution is smaller than its molar volume in the pure state. Aging of the nanocomposites for 240 h does not change the observed 4 phase co-existence. We propose a crystallographic model in which the observed volumetric expansion of the MgO unit cell is primarily attributed to two hydrostatic expansive strain components accompanying solid solution formation: (i) Coulomb repulsion among O{sup 2-} ions in the immediate vicinity of Mg{sup 2+} vacancies, and (ii) misfit strain due to differences in ionic radii upon Y{sup 3+} substitution on Mg{sup 2+} sites.

36 MATERIALS SCIENCE↗

Assessment of retrogression and re-aging treatment on microstructural and mechanical properties of Al-Zn-Mg-Cu P/M alloy

In order to understand the importance of the retrogression and re-aging as a heat treatment for improving microstructural and mechanical properties of the Al-Zn-Mg-Cu powder metallurgy alloys, Al-Zn-Mg-Cu-Fe-Cr alloys were fabricated from the elemental powders. Green compacts are compressed under compaction pressure about 370 MPa. The sintering process carried out for the samples of aluminum alloys at temperature was 650°C under argon atmosphere for two hours. The sintered compacts were subjected into homogenizing condition at 470°C for 1.5 hours and then aged at 120°C for 24 hours (T6 temper) after that it carried out the retrogressed at 180°C for 30 min., and then re-aged at 120°C for 24 hours (RRA). Observations microstructures were examined using optical, scanning electron microscopy coupled with energy dispersive spectroscopy and X-ray diffraction. Density and porosity content was conducted for the samples of alloys. The result showing that the highest Vickers hardness exhibited for an Al-Zn-Mg-Cu alloy after underwent the retrogression and reaging treatment. Increasing in hardness was because of the precipitation hardening through precipitate the (Mg Zn) and (Mg{sub 2}Zn{sub 11}) phases during matrix of aluminum-alloy.

36 MATERIALS SCIENCE↗

Aging of ErT2 thin films: ERD analysis of mechanical property changes

Rare earth tritide films evolve as tritium decays into 3He, which forms bubbles that influence long-term film stability in applications such as neutron generators. We followed the properties of model ErT2 films as they aged using ERD analysis to monitor T and 3He profiles, nanoindentation testing for mechanical properties and transmission electron microscopy to characterize bubble growth. The profiles of T and 3He are separately measured in ERD using a E - E detector, taking advantage of the differences in energy loss within the E detector. The composition measured by ERD followed the expected build-up of 3He up to near critical release, where 3He begins to escape from the film as bubbles overlap. These measurements complement observations of the changing mechanical properties of these films, where the observed behavior divided into two regimes: a substantial increase in layer hardness but elasticity little changed over 18 months, followed by a decrease in elastic stiffness and a modest decrease in hardness over the final 24 months. The evolution of properties has been explained by a combination of dislocation pinning by the bubbles, elastic softening as the bubbles occupy an increasing fraction of the material, and details of bubble growth modes. The ERD measurements confirm that the changes in properties are due to changes in bubble morphology and not to changes in 3He or T content.

36 MATERIALS SCIENCE↗