Portable lightweight bandsaw
Bandsaw of aluminum-6061 weighs about five kg and is operable by one or two men. Spiral blade cuts in any direction and at any angle. Hardness of materials to be cut is limited by material and dimension of blade.
SEARCH · Engineering Papers
Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.
Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.
Bandsaw of aluminum-6061 weighs about five kg and is operable by one or two men. Spiral blade cuts in any direction and at any angle. Hardness of materials to be cut is limited by material and dimension of blade.
Fabric knitted on conventional knitting machines uses commercially available yarns, has high aerodynamic drag capability, and is relatively inexpensive. The two yarn components used are 15-denier nylon monofilament and aluminized Mylar tape.
Self evacuating multilayer insulation system of aluminized Mylar and polyurethane foam for liquid hydrogen tanks
Spectrum analyzer, utilizing techniques similar to those used to classify energy levels of nuclear particles, is incorporated into electric field detector. Primary advantage is ability to perform qualitative broad-band frequency analysis over a large dynamic amplitude range with minimum weight and electrical power requirements.
A baseline configuration for a three section folding array, with retraction capability, was developed which would utilize electroformed aluminum hollowcore substrates and beryllium frames. The three section array was not fabricated because of difficulties with impurities in the aluminum electroforming bath. A procedure was developed for etching the copper mandrel from virtually any size of aluminum hollowcore panel in approximately one hour. Procedures were developed for analyzing the content of peroxide, water, total aluminum, and lithium-aluminum-hydride in an aluminum electroforming solution.
The use of a low density, polyurethane based foam to suppress a fire and to provide protection for the structure of an aircraft or spacecraft is discussed. The mechanism by which foams provide protection from heat and create a nonflammable surface is described. Various materials and their application to specific types of structures are examined.
Thin gage materials selected and the rationale for their basic requirements are discussed. The resin used in all prepreg manufacture is Monsanto RS-6234 polyimide. The selected fiber for core manufacture is Hercules HT-S, and the selected fiber for face sheets is Hercules HM-S. The technique for making thin gage prepreg was to wind spread carbon fiber tows into a resin film on a large drum. This technique was found to be superior to others investigated. A total of 22 pounds of 1 to 2 mil/ply prepreg was fabricated for use on the program.
A conceptual design was developed for an MLI system which will meet the design constraints of an ILRV used for 7- to 30-day missions. The ten tasks are briefly described: (1) material survey and procurement, material property tests, and selection of composites to be considered; (2) definition of environmental parameters and tooling requirements, and thermal and structural design verification test definition; (3) definition of tanks and associated hardware to be used, and definition of MLI concepts to be considered; (4) thermal analyses, including purge, evacuation, and reentry repressurization analyses; (5) structural analyses (6) thermal degradation tests of composite and structural tests of fastener; (7) selection of MLI materials and system; (8) definition of a conceptual MLI system design; (9) evaluation of nondestructive inspection techniques and definition of procedures for repair of damaged areas; and (10) preparation of preliminary specifications.
Fiberglass is wound in three winding and cure sequences with first two followed by grit blasting of surface before final step. Result is uniformly stressed metal liner assembly with excellent structural characteristics.
Panels are constructed of honeycombed polyimide/graphite core covered with thin face sheet of same material. Fabrication is based on extension of thin-gage graphite technology and modification of glass filament polyimide honeycomb techniques.
Antenna was produced in segments. Parabole sections were built up as aluminum foil sandwich with core bonded by film adhesive; whole structure was oven-cured after assembly. Structure was assembled with special tool for splice-bonding segments into complete dish, and inflatable bladder to apply pressure at joints during cure.
Material features combination of Mylar, for strength, and Saran, for impermeable qualities. Second lamination of Mylar prevents blocking, adds strength, and increases barrier rating. Different combinations of laminations produce variety of thicknesses and barrier ratings. Material can be metallized for increased barrier reliability and radar reflectivity, and can be treated with a heat-resistant coating.
Work performed in the last three phases of the program included: (1) face sheet processing; (2) honeycomb core manufacture; (3) face sheet-to-core bonding development; and (4) sandwich panel fabrication and testing. Resin cure studies were a major portion of this effort since processing problems traced to the polyimide matrix resin had to be resolved before quality core and face sheets could be fabricated. Honeycomb core fabrication and testing were conducted by Hexcel Corporation. A total of four graphite/polyimide resin composite cores were fabricated, tested, and reported. Two sandwich panels weighing .48 and .58 lb/sq ft, respectively were designed and fabricated which meet the support structure loads for the shuttle orbiter thermal protection system.
Analytical and experimental studies were performed to evaluate the structural efficiencies afforded by the selective reinforcement of conventional aluminum compression panels with unidirectional boron epoxy composite materials. A unique approach for selective reinforcement was utilized called boron/epoxy infiltration. This technique uses extruded metal sections with preformed hollow voids into which unidirectional boron filaments are drawn and subsequently infiltrated with resin to form an integral part. Simplified analytical models were developed to investigate the behavior of stiffener webs with reinforced flanges. Theoretical results are presented demonstrating the effects of transverse shear, of the reinforcement, flange eccentricity and torsional stiffness in such construction. A series of 55 tests were conducted on boron-infiltrated rods and extruded structural sections.
The development of structurally efficient, metal-lined, glass-fiber composite pressure vessels. Both the current state-of-the-art and current problems are discussed along with fracture mechanics considerations for the metal liner. The design concepts used for metal-lined, glass-fiber, composite pressure vessels are described and the structural characteristics of the composite designs are compared with each other and with homogeneous metal pressure vessels. Specific design techniques and available design data are identified. Results of a current program to evaluate flaw growth and fracture characteristics of the metal liners are reviewed and the impact of these results on composite pressure vessel designs is discussed.
The elements in the evacuated multilayer insulation system were investigated, and the major weight contributors for optimization selected. Outgassing tests were conducted on candidate vacuum jacket materials and experiments were conducted to determine the vacuum and structural integrity of selected vacuum jacket configurations. A nondestructive proof test method, applicable to externally pressurized shells, was validated on this program.
The adaptation of the Self Evacuating Multilayer Insulation System to the space shuttle orbiter liquid hydrogen tanks was investigated. Small scale material screening tests and subscale panel tests demonstrated the potential of the insulation to withstand the anticipated 100 flight cycles. The composition of the material and the process for producing the finished insulation are described. Results of the various tests to determine the durability of the material are presented.
Low mass bearing balls with hardened iron-plated surfaces can eliminate problems of low fatigue strength and flexure fatigue, and lead to increased life and reliability of high speed ball bearings. Low mass balls exert lower centrifugal forces on outer race of bearing thus eliminating detrimental effect of high speed operation.