Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “jet flow”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS2002

Effect of Gravity on the Near Field Flow Structure of Helium Jet in Air

Experiments have shown that a low-density jet injected into a high-density surrounding medium undergoes periodic oscillations in the near field. Although the flow oscillations in these jets at Richardson numbers about unity are attributed to the buoyancy, the direct physical evidence has not been acquired in the experiments. If the instability were indeed caused by buoyancy, the near-field flow structure would undergo drastic changes upon removal of gravity in the microgravity environment. The present study was conducted to investigate this effect by simulating microgravity environment in the 2.2-second drop tower at the NASA Glenn Research Center. The non-intrusive, rainbow schlieren deflectometry technique was used for quantitative measurements of helium concentrations in buoyant and non-buoyant jets. Results in a steady jet show that the radial growth of the jet shear layer in Earth gravity is hindered by the buoyant acceleration. The jet in microgravity was 30 to 70 percent wider than that in Earth gravity. The microgravity jet showed typical growth of a constant density jet shear layer. In case of a self-excited helium jet in Earth gravity, the flow oscillations continued as the jet flow adjusted to microgravity conditions in the drop tower. The flow oscillations were however not present at the end of the drop when steady microgravity conditions were reached.

Agrawal, Ajay K.↗
NASA NTRS1972

Effects of rotating flows on combustion and jet noise.

Experimental investigations of combustion in rotating (swirling) flow have shown that the mixing and combustion processes were accelerated, flame length and noise levels significantly decreased, and flame stability increased relative to that obtained without rotation. Unsteady burning accompanied by a pulsating flame, violent fluctuating jet, and intense noise present in straight flow burning were not present in rotating flow burning. Correlations between theory and experiment show good agreement. Such effects due to rotating flows could lead to suppressing jet noise, improving combustion, reducing pollution, and decreasing aircraft engine size. Quantitative analysis of the aero-acoustic relationship and noise source characteristics are needed.-

Schwartz, I. R.↗
NASA NTRS1979

Use of arc-jet hypersonic blunted wedge flows for evaluating performance of Orbiter TPS

Arc-jet tests at NASA/JSC have been conducted recently to evaluate the performance of the Orbiter Thermal Protection System (TPS) on three critical areas of the side and top of the Orbiter fuselage: (1) cargo bay door, (2) crew access door, and (3) LRSI/FRSI joint regions. Test articles corresponding to these three areas on the Orbiter were mounted in an arc-jet test chamber in a blunted-wedge holder and exposed to hypersonic flow at various angles of attack. The effects of flow direction, heating load, and overtemperature were investigated. In addition, the reuse capability of the TPS materials was evaluated, along with the protection of the pressure seals within the test articles. Thermal match model predictions correlated well with primary structure thermocouple data. Heating rate and pressure predictions based on a nonequilibrium flow field computer program showed good agreement with arc-jet test data and existing hypersonic flow theories.

Rochelle, W. C.↗
NASA NTRS1977

Investigation of Inlet Concepts for Maneuver Improvement at Transonic Speeds

A 15 percent scale lightweight fighter type inlet forebody was tested in the Ames 14 foot transonic wind tunnel at Mach numbers of 0.7, 0.9, and 1.04. The inlet was a two dimensional horizontal ramp system designed for a Mach number of 2.2. Four inlet devices designed to prevent or delay cowl-lip boundary layer separation or to improve the inlet internal flow characteristics at high angles of attack were investigated. The devices used to control cowl-lip separation consisted of cowl leading edge flaps, slotted flaps, and tangential blowing. To improve the internal flow characteristics, discrete jet nozzle flows were directed downstream and parallel to the duct surface in the subsonic diffuser to energize the wall boundary layer. The discrete jets used in the subsonic diffuser were also tested in combination with each of the cowl leading edge devices. Test measurements included engine-face total pressure recovery, steady state distortion, dynamic distortion, duct boundary layer profiles, and duct-surface static pressures.

Latham, E.↗
NASA NTRS1985

Coherent large-scale structures in high Reynolds number supersonic jets

The flow structure of a 50.8 mm (2 in) diameter jet operated at a full expanded Mach number of 1.37, with Reynolds numbers in the range 1.7 to 2.35 million, was examined for the first 20 jet diameters. To facilitate the study of the large scale structure, and determine any coherence, a discrete tone acoustic excitation method was used. Phase locked flow visualization as well as laser velocimeter quantitative measurements were made. The main conclusions derived from this study are: (1) large scale coherent like turbulence structures do exist in large Reynolds number supersonic jets, and they prevail even beyond the potential core; (2) the most preferential Strouhal number for these structures is in the vicinity of 0.4; and (3) quantitatively, the peak amplitudes of these structures are rather low, and are about 1% of the jet exit velocity. Finally, since a number of unique problems related to LV measurements in supersonic jets were encountered, a summary of these problems and lessons learned therefrom are also reported.

Lepicovsky, J.↗
NASA NTRS1991

Intrusive and nonintrusive measurements of flow properties in arc jets

While numerous diagnostic techniques are available for determining the flow properties of arc jets, these have to be used complementarily in order to cover all the requisite information. Although intrusive techniques disturb the flow, they yield much information. The determination of total enthalpy remains a major challenge, and accurate heat-flux measurements entail knowledge of atom recombination and chemical energy recombination coefficients. Such state-specific methods as the spectroscopic and laser techniques are useful in understanding the chemistry and nonequilibrium reaction and excitation rates of the flow.

Scott, Carl D.↗
NASA NTRS2002

Pitched and Yawed Circular Jets in Cross-Flow

Results from an experimental investigation of flow field generated by pitched and yawed jets discharging from a flat plate into a cross-flow are presented. The circular jet was pitched at alpha = 20 degrees and 45 degrees and yawed between beta = 0 degrees and 90 degrees in increments of 15 degrees. The measurements were performed with two X-wires providing all three components of velocity and turbulence intensity. These data were obtained at downstream locations of x = 3, 5, 10 and 20, where the distance x normalized by the jet diameter, is measured from the center of the orifice. Data for all configurations were acquired at a momentum-flux ratio J = 8. Additionally, for selected angles and locations, surveys were conducted for J = 1.5, 4, and 20. As expected, the jet penetration is found to be higher at larger alpha. With increasing beta the jet spreads more. The rate of reduction of peak streamwise vorticity, with the downstream distance is significantly lessened at higher alpha but is found to be practically independent of alpha. Thus, at the farthest measurement station x = 20, omega(sub xmax) is about five times larger for beta = 0 degrees compared to the levels at beta = 0 degrees. Streamwise velocity within the jet-vortex structure is found to depend on the parameter J. At J = 1.5 and 4, 'wake-like' velocity profiles are observed. In comparison, a 'jet-like' overshoot is present at higher J.

Milanovic, Ivana M.↗
NASA NTRS1981

Noise radiated from inverted velocity profile jets under simulated flight

Measurements were made of the noise radiated by an inverted profile coannular jet. The measurements were made inside an anechoic chamber and forward flight was simulated with an open jet surrounding a coannular nozzle. The diameters of the center and the annular nozzles were 1.27 cm and 2.03 cm, respectively. The open jet wind tunnel was 17.1 cm in diameter and could be operated at speeds up to 150 m/sec. Noise measurements were made in the acoustic far field at several spherical angles ranging from 20 deg to 120 deg relative to the jet axis. Flow through the center jet decreased the noise radiated by the annular jet. The addition of forward velocity further decreased the noise, and the two noise reductions seem to be additive. Measurements of the mean velocity profile demonstrate that forward flight reduced the growth rate of the high speed annular jet, and that center flow reduced the rate of merging of the annular jet.

Petersen, R. A.↗
NASA NTRS2010

Boundary-layer-ingesting inlet flow control system

A system for reducing distortion at the aerodynamic interface plane of a boundary-layer-ingesting inlet using a combination of active and passive flow control devices is disclosed. Active flow control jets and vortex generating vanes are used in combination to reduce distortion across a range of inlet operating conditions. Together, the vortex generating vanes can reduce most of the inlet distortion and the active flow control jets can be used at a significantly reduced control jet mass flow rate to make sure the inlet distortion stays low as the inlet mass flow rate varies. Overall inlet distortion, measured and described as average SAE circumferential distortion descriptor, was maintained at a value of 0.02 or less. Advantageous arrangements and orientations of the active flow control jets and the vortex generating vanes were developed using computational fluid dynamics simulations and wind tunnel experimentations.

Owens, Lewis R.↗
NASA NTRS1974

Calculations of the pressure distribution on axisymmetric boattails including effects of viscous interactions and exhaust jets in subsonic flow

A method of calculating the pressure distributions on boattails is proposed. This method accounts for viscous effects including the presence of a separated region for base flows by combining an inviscid analysis with a boundary layer analysis in an iterative calculation. Details of the reversed flow region are not considered. Some preliminary results have been obtained for boattails at subsonic free stream Mach number with turbulent boundary layers separating at the boattail base. In some cases convergence could not be obtained using the present computer program. It is possible, in principle, to extend this method to the calculation of boattail flows with pressure gradient induced separation on the boattail.

Rom, J.↗
NASA NTRS1974

Effect of interjet spacing on mixing of multiple coaxial jets in supersonic flow

An experimental and analytical investigation of strut-mounted, four-nozzle, downstream facing, gaseous fuel injector assembly was conducted in a Mach 4 air-stream with P = 154 psia and T sub o 520 R. Helium was used as the injectant, and the interjet spacing (S/D) was the main parameter varied. The principal data are in the form of Helium concentration profiles at seven axial stations, Mach number distributions at three axial stations and schlieren photographs of the flow field at different interjet spacings. An approximate analysis was developed based upon a linearization in the Von Mises plane, Crocco integrals for the temperature and concentrations fields and an eddy viscosity model. Good agreement with the data was achieved. It was found that, at these conditions, interjet spacing has an effect on mixing only up to S/D of approximately 2.5, with concentration of injectant becoming smaller as S/D is increased, and the Mach number downstream of the injector tends to decrease with decreasing S/D.

Lorber, A. K.↗
NASA NTRS1977

Theoretical prediction of over-wing-blowing aerodynamics

A theoretical method is developed for predicting the aerodynamic characteristics of wings with over-wing-blowing jet. The method allows the jet to stay above the wing surface as well as to wash the surface. It accounts for the wing-jet interaction due to differences between the jet and freestream dynamic pressures and Mach numbers, in addition to the jet entrainment. For the former effect, the quasi-vortex-lattice method is used to satisfy the jet and wing boundary conditions. For the latter, a new theory was developed to calculate the jet entrained flow for given jet properties. Comparison of predicted results with available data of various configurations shows reasonably good agreement. Further theoretical analysis indicates that it is aerodynamically advantageous to locate the jet exit near and ahead of the wing leading edge, and that the camber shape has significant effect on the induced drag.

Lan, C. E.↗
NASA NTRS1981

Prediction of jet exhaust noise on airframe surfaces during flight

The behavior of pressure fluctuations measured on the airframe of a prototype high lift jet transport (YC-14) is presented. The data are characterized in terms of a particular jet exhaust flow field idealization, jet mixing noise, and exhaust shock noise. Generalized spectrum shapes and scaling relations for peak level and frequency of peak level are developed, and the frequency is found to depend on jet exhaust velocity and aircraft velocity. Comparisons are made with near-field engine exhaust noise of a conventional jet, and results suggest that the same two exhaust noises are important for both aircraft types. Surface fluctuating pressure data are assessed, and results suggest that the jet mixing and exhaust shock noise source characterizations for the YC-14 have useful applicability to conventionally configured jets.

Butzel, L. M.↗