Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “isotherm”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS1988

Temperature control in wafer-level testing of large multi-segment electromigration test structures

The paper describes two methods for maintaining a constant metallization temperature throughout a wafer-level isothermal electromigration test of large multisegment test structures where Joule-heating is high and chip to chuck thermal contact is poor. In the first method, an initial calibration of Joule heating versus metal temperature is carried out. During the isothermal electromigration test, the Joule heating is continuously monitored and the chuck temperature is adjusted based on the calibration results to maintain a constant metal temperature. In the second method, temperature sensors are fabricated on the chip and then the sensors are used to monitor the chip temperature directly. The chuck temperature is then adjusted as needed.

Zamani, Nasser↗
NASA NTRS1989

The 3F condensation polyimides: Review and update

Nine new condensation polyimides containing the phenyltrifluoroethylidene (3F) linkage were synthesized by the amic-acid route. Several other polyimides, including some with hexafluoroisopropylidene (6F) linkage, were also prepared as controls. Amic-acid solutions were characterized by determining their inherent viscosities prior to thermal conversion into polyimide films. Glass transition temperatures (T sub g), thermogravimetric analysis (TGA), and isothermal weight loss data (at 316, 371, and 371 C under 0.5 MPa air pressure) were obtained for the films. The films were pulverized into molding powders which, in turn, were thermally processed under pressure into neat resin disks. The disks were also characterized by T sub g's and 316 and 371 C isothermal weight losses. The film study identified two new polyimides with T sub g's greater than 371 C and two new polyimides with low rates of weight loss. The resin disks exhibited the same overall trends in T sub g and weight loss as the respective films, however the weight loss per unit surface area was always greater, presumably due to molecular degradation induced during preparation of the molding powders. The overall results indicate that polyimides containing the 3F linkage have T sub g's and thermo-oxidative stability comparable to polyimides containing the 6F group. Alternate technology was also shown by the synthesis of two new polyalkyl substituted 3F diamines and five more new 3F polymers. Their potential as photoresists was demonstrated by T sub g advancement after ultraviolet exposure. Last, four U.S. patents on 3F monomers and polymers were issued and up to eight more are pending.

Alston, William B.↗
NASA NTRS1989

Development of free-piston Stirling engine performance and optimization codes based on Martini simulation technique

A FORTRAN computer code is described that could be used to design and optimize a free-displacer, free-piston Stirling engine similar to the RE-1000 engine made by Sunpower. The code contains options for specifying displacer and power piston motion or for allowing these motions to be calculated by a force balance. The engine load may be a dashpot, inertial compressor, hydraulic pump or linear alternator. Cycle analysis may be done by isothermal analysis or adiabatic analysis. Adiabatic analysis may be done using the Martini moving gas node analysis or the Rios second-order Runge-Kutta analysis. Flow loss and heat loss equations are included. Graphical display of engine motions and pressures and temperatures are included. Programming for optimizing up to 15 independent dimensions is included. Sample performance results are shown for both specified and unconstrained piston motions; these results are shown as generated by each of the two Martini analyses. Two sample optimization searches are shown using specified piston motion isothermal analysis. One is for three adjustable input and one is for four. Also, two optimization searches for calculated piston motion are presented for three and for four adjustable inputs. The effect of leakage is evaluated. Suggestions for further work are given.

Martini, William R.↗
NASA NTRS1990

Investigation of the reaction kinetics between SiC fibers and selectively alloyed titanium matrix composites and determination of their mechanical properties

During high temperature exposure, an interfacial reaction occurs between SiC fiber reinforcement and titanium matrices which can be detrimental to the mechanical properties of the composite. The reaction kinetics between SCS-6 fibers and Ti-1100 were determined at 800 to 1000 C and found to be slower than those of other currently used titanium alloys (Ti-15-3, Ti-6-4). The experimentally determined reaction kinetics for Ti-1100 were extrapolated to 700 C and found to accurately predict reaction zone size after 1000 hours of exposure. Predictions of the time to consume the surface layer on the SCS-6 and SCS-9 fibers were made in an effort to estimate the time that the fiber will retain its strength in Ti-1100 during isothermal exposure at high temperatures. Using this approach, the strength of an SCS-6 fiber in Ti-1100 should be retained for over 20,000 hours at isothermal exposures less than 800 C. Strength predictions using the rule of mixtures for a unidirectional Ti-1100/SCS-6 composite are presented for short term exposures up to 700 C. Room temperature tests of an as-fabricated 20 volume percent fiber/Ti-1100 composite yielded a UTS of 226 ksi (1490 MPa) which is close to that predicted by the ROM.

Gundel, Douglas B.↗
NASA NTRS1989

Oxidation behavior of FeAl+Hf,Zr,B

The oxidation behavior of Fe-40Al-1Hf, Fe-40Al-1Hf-0.4B, and Fe-40Al-0.1Zr-0.4B (at. percent) alloys was characterized after 900, 1000, and 100 C exposures. Isothermal tests revealed parabolic kinetics after a period of transitional theta-alumina scale growth. The parabolic growth rates for the subsequent alpha-alumina scales were about five times higher than those for NiAl+0.1Zr alloys. The isothermally grown scales showed a propensity toward massive scale spallation due to both extensive rumpling from growth stresses and to an inner layer of Hf02. Cyclic oxidation for 200 1-hr cycles produced little degradation at 900 or 1000 C, but caused significant spallation at 1100 C in the form of small segments of the outer scale. The major difference in the cyclic oxidation of the three FeAl alloys was increased initial spallation for FeAl+Zr,B. Although these FeAl alloys showed many similarities to NiAl alloys, they were generally less oxidation resistant. It is believed that this resulted from nonoptimal levels of dopants and larger thermal expansion mismatch stresses.

Smialek, James L.↗
NASA NTRS1989

Upper ocean thermal and flow fields at 0 deg, 28 deg W (Atlantic) and 0 deg, 140 deg W (Pacific) during 1983-1985

Moored current and temperature measurements were recorded simultaneously for 2 years (August 1983 to July 1985) at six or seven depths between 10 and 250 m on the equator at 28 deg W in the Atlantic and at 140 deg W in the Pacific. The mean depth of the 20-C isotherm, which was representative of thermocline displacements, was identical at both sites. Substantially different annual cycles of the thermal and flow fields represent an enigma. The annual variation of the 20-C isotherm was much less at 140 deg W than at 28 deg W.

Halpern, David↗
NASA NTRS1991

Thermal annealing of GaAs concentrator solar cells

Isochronal and isothermal annealing tests were performed on GaAs concentrator cells which were irradiated with electrons of various energies to fluences up to 1 x 10(exp 16) e/sq cm. The results include: (1) For cells irradiated with electrons from 0.7 to 2.3 MeV, recovery decreases with increasing electron energy. (2) As determined by the un-annealed fractions, isothermal and isochronal annealing produce the same recovery. Also, cells irradiated to 3 x 10(exp 15) or 1 x 10(exp 16) e/sq cm recover to similar un-annealed fractions. (3) Some significant annealing is being seen at 150 C although very long times are required.

Curtis, H. B.↗
NASA NTRS1991

Dehydration kinetics of talc at 1 bar

Experimental results on the dehydration kinetics of talc, which is likely to be a major potential resource for water and hydrogen in carbonaceous chondrites, is presented. The rate of dehydration of an essentially pure Mg-end member natural talc, (Mg(.99)Fe(.01))3Si4O10(OH)2, was studied by measuring in situ weight change under isothermal condition at 1 bar as a function of time in the temperature range 775 to 985 C. The grain size of the starting material was 0.7 to 1 micron. It was found that the data up to 50 to 60 percent dehydration can be fitted by an equation of the form alpha = exp(-Kt(exp n)), where alpha is the weight fraction of talc remaining, K is a rate constant and n is a numerical constant for a given temperature. For any set of isothermal data, there is a major change in the value of n for larger dehydration. For up to approximately 50 percent dehydration, all rate constants can be described by an Arrheniun relation with an activation energy of 432 (+/- 30) kJ/mol; n has a nearly constant value of 0.54 between 775 and 875 C, but increases almost linearly according to n = -10.77 + 0.012T C at T greater than or equal to 875 C.

Ganguly, J.↗
NASA NTRS1991

A comparative flow visualization study of thermocapillary flow in drops in liquid-liquid systems

Experiments are performed to visualize thermocapillary flow in drops in an immiscible host liquid. The host liquid used is silicone oil. Drops of three different liquids are used, viz, vegetable oil, water-methanol mixture anad pure methanol. Clear evidence of thermocapillary flow is seen in vegetable oil drops. For a mixture of water and methanol (approximately 50-50 by weight), natural convection is seen to dominate the flow outside the drop. Pure methanol drops exhibit thermocapillary flow, but dissolve in silicone oil. A small amount of water added to pure methanol significantly reduces the dissolution. Flow oscillations occur in this system for both isothermal and non-isothermal conditions.

Balasubramaniam, R.↗
NASA NTRS1991

Crosslinking-property relationships in PMR polyimide composites. I

The effect of the crosslink density of the matrix on physical and mechanical properties of a graphite-fiber-reinforced PMR (for polymerization of monomer reactants) polyimide composites during isothermal aging was investigated in experiments where unidirectional composite specimens of Celion 6000/PMR-P1 were isothermally exposed at 288 C in air for various time periods up to 5000 hrs. It was found that, as the crosslink density increased, the glass transition temperature, density, and elevated-temperature interlaminar shear strength of a composite increased, while the initial moisture absorption and the coefficient of thermal expansion decreased. However, after reaching the highest possible matrix crosslink density, several of the composite properties began to deteriorate rapidly.

Pater, R. H.↗
NASA NTRS1991

A simulation of the collapse and fragmentation of cooling molecular clouds

The application of the Smoothed Particle Hydrodynamics method to the fragmentation of rotating cloud and disk systems is described, allowing for molecular cooling due to H2 and CO. A novel approach to solving Poisson's equation for disklike structures which exploits the multigrid algorithm is also described. Numerical studies are presented which investigate the evolution of both rotating clouds and Maclaurin disks, in each case with both an isothermal equation of state and with molecular cooling. The results establish the influence of molecular cooling on the fragmentation of molecular clouds. The isothermal sequences, if they fragment at all, do so into far fewer lumps than the cooling sequences. This is not due to a cooling instability as such, but rather to the reduced thermal support. One of the sequences shows a remarkable similarity to the W49A star-forming region.

Monaghan, Joe J.↗
NASA NTRS1991

Three dimensional numerical investigation of gravitational and solutal effects in a cylindrical cell

Three-dimensional numerical computations of natural convection in a cylindrical ampoule (L/R = 4) are presented for a Ga-doped Ge melt. The ampoule is maintained at isothermal end conditions, and the g vector is oriented at an angle gamma with the cylinder axis. Detailed velocity, temperature, and concentration field distributions are presented for different gravity levels and a range of inclination angles (gamma between 0 and 180 deg). For terrestrial conditions, complex, multicellular flow is found to occur for gamma between 0 and 180 deg. The strong convection results in significant isotherm distortions and enhanced heat transfer. As the gravity level is reduced to 0.001 g(0), the overall convection strength decays but the 3D multicellular flow persists, causing appreciable mass transfer. For a further reduction in the gravity level to 0.00001 g(0), the system thermo/solutal characteristics are close to a purely diffusive behavior. Flow and thermal and solutal distributions are presented in the principal, orthogonal, and cross sectional planes, and the average system heat and mass transfer are calculated.

Ramachandran, N.↗
NASA NTRS1991

A review of the regional geophysics of the Arizona Transition Zone

A review of existing geophysical information and new data presented in this special section indicate that major changes in crustal properties between the Basin and Range and Colorado Plateau occur in, or directly adjacent to, the region defined as the Arizona Transition Zone. Although this region was designated on a physiographic basis, studies indicate that it is also the geophysical transition between adjoining provinces. The Transition Zone displays anomalous crustal and upper mantle seismic properties, shallow Curie isotherms, high heat flow, and steep down-to-the-plateau Bouguer gravity gradients. Seismic and gravity studies suggest that the change in crustal thickness, from thin crust in the Basin and Range to thick crust in the Colorado Plateau, may occur as a series of steps rather than a planar surface. Anomalous P wave velocities, high heat flow, shallow Curie isotherms, and results of gravity modeling suggest that the upper mantle is heterogeneous in this region. A relatively shallow asthenosphere beneath the Basin and Range and Transition Zone contrasted with a thick lithosphere beneath the Colorado Plateau would be one explanation that would satisfy these geophysical observations.

Hendricks, J. D.↗
NASA NTRS1991

Performance of journal bearings with semi-compressible fluids

Cryogenic fluids in isothermal rigid surface and foil type journal bearings can sometimes be treated as semicompressible fluids. In these applications, the fluid density is a function of the pressure. At low pressures, the fluids can change from a liquid to a saturated liquid-vapor phase. The performance of a rigid surface journal bearing with an idealized semicompressible fluid is discussed. Pressure solutions are based upon a Reynolds equation which includes the effects of a compressibility via the bulk modulus of the fluid. Results are contrasted with the performance of isothermal constant property incompressible fluids.

Carpino, M.↗
NASA NTRS1991

A silicone column for GC analysis of polar and nonpolar chemicals

The investigation of the Saturnian System is being proposed jointly by NASA and the European Space Agency (ESA). The mission is scheduled for a launch in 1996. The mission provides an opportunity for close observation and exploration of Saturn's atmosphere, the complex Saturnian System of satellites and rings, Titan (Saturn's planet-sized moon), and Saturn's magnetosphere. The mission gives special attention to Titan which is blanketed by a thick, opaque atmosphere. An atmospheric probe will be deposited into the Titan Atmosphere for in situ measurement during a slow, three hour descent to the surface. The results from this analysis may provide the information which is important to the research of chemical evolution, and the origin of life. An analytical system was developed as a part of the Titan Aerosol Gas Experiment (TAGEX), a proposed experiment for the Cassini Mission. This system will use two highly sensitive detectors, the Metastable Ionization Detector (MID) and the Ion Mobility Spectrometer (IMS). Unfortunately, when commercial columns are utilized with these highly sensitive detectors, volatile components continuously bleed from the column and interfere with the detector. In addition, light columns must be able to separate polar and nonpolar organic chemicals within 10-15 minutes under isothermal conditions for the Titan Mission. Therefore, a highly crosslinked silicone polymeric packed column was developed which is able to efficiently separate amines, alcohols, and hydrocarbons with retention times less that 15 minutes at 100 C isothermal condition.

Shen, T. C.↗
NASA NTRS1991

Crustal magnetization and temperature at depth beneath the Yilgarn block, Western Australia inferred from Magsat data

Variations in crustal magnetization along a seismic section across the Archean Yilgarn block of Western Australia inferred from Magsat data are interpreted as a subtle thermal effect arising from variations in depth to the Curie isotherm. The isotherm lies deep within the mantle of the eastern part of the province, but transects the crust-mantle transition and rises well into the crust on the western side. The model is consistent with heat flow variations along the section line. The mean crustal magnetization implied by the model is approximately 2 A/m. The temperature variation implied by the model is consistent with the hypothesis that the crust-mantle transition seen seismically corresponds to the mafic granulite-eclogite phase transition within a zone of igneous crustal underplating.

Mayhew, M. A.↗
NASA NTRS1992

Gravitational lensing, time delay, and gamma-ray bursts

The probability distributions of time delay in gravitational lensing by point masses and isolated galaxies (modeled as singular isothermal spheres) are studied. For point lenses (all with the same mass) the probability distribution is broad, and with a peak at delta(t) of about 50 S; for singular isothermal spheres, the probability distribution is a rapidly decreasing function with increasing time delay, with a median delta(t) equals about 1/h month, and its behavior depends sensitively on the luminosity function of galaxies. The present simplified calculation is particularly relevant to the gamma-ray bursts if they are of cosmological origin. The frequency of 'recurrent' bursts due to gravitational lensing by galaxies is probably between 0.05 and 0.4 percent. Gravitational lensing can be used as a test of the cosmological origin of gamma-ray bursts.

Mao, Shude↗
NASA NTRS1992

Oxidation kinetics of CVD silicon carbide and silicon nitride

The long-term oxidation behavior of pure, monolithic CVD SiC and Si3N4 is studied, and the isothermal oxidation kinetics of these two materials are obtained for the case of 100 hrs at 1200-1500 C in flowing oxygen. Estimates are made of lifetimes at the various temperatures investigated. Parabolic rate constants for SiC are within an order of magnitude of shorter exposure time values reported in the literature. The resulting silica scales are in the form of cristobalite, with cracks visible after exposure. The oxidation protection afforded by silica for these materials is adequate for long service times under isothermal conditions in 1-atm dry oxygen.

Fox, Dennis S.↗