SEARCH · Engineering Papers

Results for “high performance analytics”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

SourceResearch connectionFrom yearThrough year

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43

All sources NASA NTRS DOE OSTI

NASA NTRS1977

Tilt-proprotor perspective

The general tilt-proprotor concept is discussed, and a more detailed look at the XV-15 aircraft is taken. The special features of the two-engine system, engine control system, and flight control system are mentioned. The main objectives of the XV-15 program are to (1) verify rotor/pylon/wing/dynamic stability and aircraft performance over a representative operational envelope, (2) assess the handling qualities and establish a safe operating envelope, and (3) investigate gust sensitivity, effects of downwash, and hover operation. With regard to rotor/pylon stability, one challenge is to be able to predict a parameter's value and then build hardware to match. The analytical program has gained some respect through aeroelastic and full-scale XV-3 demonstrations. Special concern centers around the thrust and power management system when flying at high speed when very small changes in rotor collective pitch represent large changes in thrust and power. Demonstration of the system awaits wind-tunnel and flight testing.

Few, D. D.↗

NASA NTRS1994

An application of miniscale experiments on Earth to refine microgravity analysis of adiabatic multiphase flow in space

Adiabatic two-phase flow is of interest to the design of multiphase fluid and thermal management systems for spacecraft. This paper presents original data and unifies existing data for capillary tubes as a step toward assessing existing multiphase flow analysis and engineering software. Comparisons of theory with these data once again confirm the broad accuracy of the theory. Due to the simplicity and low cost of the capillary tube experiments, which were performed on earth, we were able to closely examine for the first time a flow situation that had not previously been examined appreciably by aircraft tests. This is the situation of a slug flow at high quality, near transition to annular flow. Our comparison of software calculations with these data revealed overprediction of pipeline pressure drop by up to a factor of three. In turn, this finding motivated a reexamination of the existing theory, and then development of a new analytical and is in far better agreement with the data. This sequence of discovery illustrates the role of inexpensive miniscale modeling on earth to anticipate microgravity behavior in space and to complete and help define needs for aircraft tests.

Rothe, Paul H.↗

NASA NTRS1997

Cure Chemistry of Phenylethynyl Terminated Oligomers

The ability to process high performance polymers into quality, void-free composites has been significantly advanced using oligomers terminated with reactive groups which cure or crosslink at elevated temperature without the evolution of volatile byproducts. Several matrix resin systems of considerable interest to the aerospace community utilize phenylethynyl-terminated imide (PETI) technology to achieve this advantage. The present paper addresses the cure chemistry of PETI oligomers. The thermal cure of a low molecular weight model compound was studied using a variety of analytical techniques including differential scanning calorimetry, Fourier transform infrared spectroscopy, and liquid chromatography-mass spectroscopy. The studies indicate an extremely complex cure process. Many stable products were isolated and this paper reports current work on identification of those products. The intent of this research is to provide fundamental insight into the molecular structure of the cured PETI engineering materials so that performance and durability can be more fully assessed.

Wood, Karen H.↗

NASA NTRS2018

Development of the Multi Purpose Transportation System for the Space Launch System (SLS) Core Stage (CS) Flight Article

NASA’s Multi Purpose Transportation System (MPTS) is designed to transport the Space Launch System vehicle segments by waterway and roadway. It is tasked with transporting the vehicle from where it is manufactured to its intermediate test location and final launch destination. Its design incorporates mechanisms that release degrees of freedom to prevent excessive loading during transit and ensure a successful delivery of the vehicle to its intended destination. In addition to the CS (Core Stage) flight article, the system will also move three structural test articles and a simulated CS Pathfinder (weight, center of gravity, outer mold line dimensions, and overall length) over road terrain on four NASA centers and on the Pegasus barge. The MPTS independently supports the article at both ends while communicating as a combined unit through automated monitoring of its released degree of freedom and corrective responses. This allows the system to constrain its payload in a statically determinate manner while traversing across highly variable terrain. Multi-body simulation of the transportation route is useful to predict free-body motion within the specified travel ranges. The MPTS has completed its design and analysis developmental cycles. This unpublished paper will describe the design challenges encountered in developing this system of large scale structure which incorporates complex mechanisms. The unique techniques and methodologies developed for analytical assessment of the hardware will be also be discussed. Key results from analytical evaluations as well as ongoing performance testing will be presented.

Sandridge, Sarah↗

NASA NTRS2023

Reduction in Computational Cost of Progressive Failure Analysis of Composite Structures

Designing aircraft structures requires efficient modeling approaches to iterate on multiple structural configurations to achieve an optimal design. Typically, damage tolerance is not considered at the design stage because of the high computational cost in its implementation within a finite element modeling approach. Therefore, analytical or empirical approaches are often used to size critical damage-tolerant structures once an optimal design is determined. In this study, the Progressive Release eXplicit Virtual Crack-Closure Technique (PRX-VCCT) is assessed for its capability to cost-effectively evaluate skin stringer separation of a blade-stiffened panel that is subjected to seven point bend loads. An initial verification study was performed to evaluate PRX VCCT to accurately simulate skin-stringer separation with respect to existing cohesive element approaches. Furthermore, the influence of element size, ranging from 0.10 in. to 0.40 in., on the total computational time using the PRX-VCCT is investigated. The results indicate that the PRX-VCCT can be used to accurately simulate skin stringer separation using large element lengths (0.40 in.). Additionally, a significant reduction in the computational time to simulate skin stringer separation is observed using the PRX-VCCT. Large-scale progressive damage analysis using PRX-VCCT can be implemented early in the design cycle of composite structures without requiring a global-to-local modeling approach.

Composites↗

NASA NTRSDate not supplied

The Genesis Non-flight Implant Sample Archive

Introduction: For the past 20 years the Genesis science community has been analyzing solar wind captured in sample collectors now curated at Johnson Space Center (JSC). Non-flown flight like collector materials (non-flight) considered reference material was always allocated by the JSC Genesis team for testing experimental procedures. However, to expedite Genesis science, distribution of non-flown reference materials were also provided by, D. S. Burnett (Genesis PI, Caltech) and A. J. G. Jurewicz (ASU) who were funded to aid all Genesis PIs by providing engineering test materials archived at Caltech pre-flight as well as ion implants into these materials [1]. Implanted materials (non-flight reference, flight-like semiconductor materials, and NIST SRM glass) received from the Caltech collection during a pilot project are being used to develop an accession procedure for the purpose of making these materials available to researchers in the future. These implant samples are important because they can be utilized as measurement standards [2]. This is a work in progress and this work reports progress in documentation and imaging. The pilot program received 63 implanted reference materials with known implanted ions. Genesis Non-Flight Database: The existing non-flight material database was modified to allow for the description of implant sessions and to allow correlation of the implant information to individual specimens. An implant session has three main components: a known ion, a known dose (ion/cm2), and a known energy (keV). Procedure: Laboratory Procedure. Upon receiving non-flight analytical standards (independently calibrated implants), or implant samples (nominally calibrated implants), they will be imaged in their current containers to capture any information written before being brought into the Genesis Sample Laboratory. Documentation is provided by the donor and used for correlating the data between the implant sessions and implant samples. This information is not verified by Genesis Curation. The microscope used to image samples in the laboratory has an automated stage with a stainless-steel plate to hold samples and a camera that utilizes the software Surveyor to take photomosaic images of the implant samples. The camera attached to the microscope is a QICAM High Performance IEEE 1394 FireWire Digital CCD Camera. This setup, shown in Fig. 1, allows for photomosaics of small-scale samples with a 10x objective or 25x objective. Examples of images taken with this microscope setup are shown in Fig.2 and Fig. 3. After imaging, samples get stored in a clean fluoroware container or polypropylene vial depending on sample size for long term storage. Database Procedure. The Genesis Non-Flight Database currently allows for the addition of implant sessions. The required fields for adding an implant session are the implant session ion, the implant session dose, and the implant session energy. There are also fields for the date and vendor of the sessions as well as a field for if the session was calibrated or not. Once an implant session has been inserted into the database, additional documentation from the session can be attached. The database will automatically assign an Implant Session Number. After inserting an implant session, the implanted samples can be inserted. The fields required for an implant sample are the material of the sample and the size of the sample. The Generic name for the implant sample with be automatically generated by the database once it has been inserted. Implant sample numbers begin with 3X to distinguish from flown Genesis sample numbers. There are also fields for processors to add the location (room, cabinet, tray) and container type (fluoroware, polypropylene vial). Once an implant session and an associated sample(s) have been inserted into the database the sample can be then tied to all associated implant sessions. An implant sample can be tied to multiple implant sessions. Future work: For curation, future work consists of creating an online catalogue for implant samples as well as updating the database with more samples as we receive them. For the scientific community these implant samples have many potential uses. For Genesis research, they are directly applicable for testing and, in some cases, as analytical standards. For non-Genesis research, implants (especially calibrated implants) could be used for calibrating other, unique planetary materials [1].

C D Calva↗

NASA NTRS1973

Shuttle active thermal control system development testing. Volume 3: Modular radiator system test data correlation with thermal model

Results are presented of an analysis which compares the performance predictions of a thermal model of a multi-panel modular radiator system with thermal vacuum test data. Comparisons between measured and predicted individual panel outlet temperatures and pressure drops and system outlet temperatures have been made over the full range of heat loads, environments and plumbing arrangements expected for the shuttle radiators. Both two sided and one sided radiation have been included. The model predictions show excellent agreement with the test data for the maximum design conditions of high load and hot environment. Predictions under minimum design conditions of low load-cold environments indicate good agreement with the measured data, but evaluation of low load predictions should consider the possibility of parallel flow instabilities due to main system freezing. Performance predictions under intermediate conditions in which the majority of the flow is not in either the main or prime system are adequate although model improvements in this area may be desired. The primary modeling objective of providing an analytical technique for performance predictions of a multi-panel radiator system under the design conditions has been met.

Phillips, M. A.↗

NASA NTRS1975

Technical guidance and analytic services in support of SEASAT-A

The design of a high resolution radar for altimetry and ocean wave height estimation was studied. From basic principles, it is shown that a short pulse wide beam radar is the most appropriate and recommended technique for measuring both altitude and ocean wave height. To achieve a topographic resolution of + or - 10 cm RMS at 5.0 meter RMS wave heights, as required for SEASAT-A, it is recommended that the altimeter design include an onboard adaptive processor. The resulting design, which assumes a maximum likelihood estimation (MLE) processor, is shown to satisfy all performance requirements. A design summary is given for the recommended radar altimeter, which includes a full deramp STRETCH pulse compression technique followed by an analog filter bank to separate range returns as well as the assumed MLE processor. The feedback loop implementation of the MLE on a digital computer was examined in detail, and computer size, estimation accuracies, and bias due to range sidelobes are given for the MLE with typical SEASAT-A parameters. The standard deviation of the altitude estimate was developed and evaluated for several adaptive and nonadaptive split-gate trackers. Split-gate tracker biases due to range sidelobes and transmitter noise are examined. An approximate closed form solution for the altimeter power return is derived and evaluated. The feasibility of utilizing the basic radar altimeter design for the measurement of ocean wave spectra was examined.

Brooks, W. L.↗

NASA NTRS1979

Aerodynamic characteristics of missile configurations based on Soviet design concepts

The aerodynamic characteristics of several missile concepts are examined. The configurations, which are based on some typical Soviet design concepts, include fixed-wing missiles with either forward- or aft-tail controls, and wing-control missiles with fixed aft stabilizing surfaces. The conceptual missions include air-to-air, surface-to-air, air-to-surface, and surface-to-surface. Analytical and experimental results indicate that through the proper shaping and location of components, and through the exploitation of local flow fields, the concepts provide generally good stability characteristics, high control effectiveness, and low control hinge moments. In addition, in the case of some cruise-type missions, there are indications of the application of area ruling as a means of improving the aerodynamic efficiency. In general, a point-design philosophy is indicated whereby a particular configuration is developed for performing a particular mission.

Spearman, M. L.↗

NASA NTRS1991

High enthalpy, hypervelocity flows of air and argon in an expansion tube

An expansion tube with a free piston driver has been used to generate quasi-steady hypersonic flows in argon and air at flow velocities in excess of 9 km/s. Irregular test flow unsteadiness has limited the performance of previous expansion tubes, and it has been found that this can be avoided by attention to the interaction between the test gas accelerating expansion and the contact surface in the primary shock tube. Test section measurements of pitot pressure, static pressure and flat plate heat transfer are reported. An approximate analytical theory has been developed for predicting the velocities achieved in the unsteady expansion of the ionizing or dissociating test gas.

Neely, A. J↗

NASA NTRS1993

Integration of Design, Thermal, Structural, and Optical Analysis, Including Thermal Animation

In many industries there has recently been a concerted movement toward 'quality management' and the issue of how to accomplish work more efficiently. Part of this effort is focused on concurrent engineering; the idea of integrating the design and analysis processes so that they are not separate, sequential processes (often involving design rework due to analytical findings) but instead form an integrated system with smooth transfers of information. Presented herein are several specific examples of concurrent engineering methods being carried out at Langley Research Center (LaRC): integration of thermal, structural and optical analyses to predict changes in optical performance based on thermal and structural effects; integration of the CAD design process with thermal and structural analyses; and integration of analysis and presentation by animating the thermal response of a system as an active color map -- a highly effective visual indication of heat flow.

Amundsen, Ruth M.↗

NASA NTRS1994

Focused Schlieren flow visualization studies of multiple venturi fuel injectors in a high pressure combustor

Multiple venturi fuel injectors were used to obtain uniform fuel distributions, better atomization and vaporization in the premixing/prevaporizing section of a lean premixed/prevaporized flame tube combustor. A focused Schlieren system was used to investigate the fuel/air mixing effectiveness of various fuel injection configurations. The Schlieren system was focused to a plane within the flow field of a test section equipped with optical windows. The focused image plane was parallel to the axial direction of the flow and normal to the optical axis. Images from that focused plane, formed by refracted light due to density gradients within the flow field, were filmed with a high-speed movie camera at framing rates of 8,000 frames per second (fps). Three fuel injection concepts were investigated by taking high-speed movies of the mixture flows at various operating conditions. The inlet air temperature was varied from 600 F to 1000 F, and inlet pressures from 80 psia to 150 psia. Jet-A fuel was used typically at an equivalence ratio of 0.5. The intensity variations of the digitized Schlieren images were analytically correlated to spatial density gradients of the mixture flows. Qualitative measurements for degree of mixedness, intensity of mixing, and mixing completion time are shown. Various mixing performance patterns are presented with different configurations of fuel injection points and operating conditions.

Chun, K. S.↗

NASA NTRS2015

Global Optimization of N-Maneuver, High-Thrust Trajectories Using Direct Multiple Shooting

The performance of impulsive, gravity-assist trajectories often improves with the inclusion of one or more maneuvers between flybys. However, grid-based scans over the entire design space can become computationally intractable for even one deep-space maneuver, and few global search routines are capable of an arbitrary number of maneuvers. To address this difficulty a trajectory transcription allow-ing for any number of maneuvers is developed within a multi-objective, global optimization framework for constrained, multiple gravity-assist trajectories. The formulation exploits a robust shooting scheme and analytic derivatives for com-putational efficiency. The approach is applied to several complex, interplanetary problems, achieving notable performance without a user-supplied initial guess.

trajectory design↗

NASA NTRS2017

Spectroscopic Chemical Analysis Methods and Apparatus

Spectroscopic chemical analysis methods and apparatus are disclosed which employ deep ultraviolet (e.g. in the 200 nm to 300 nm spectral range) electron beam pumped wide bandgap semiconductor lasers, incoherent wide bandgap semiconductor light emitting devices, and hollow cathode metal ion lasers to perform non-contact, non-invasive detection of unknown chemical analytes. These deep ultraviolet sources enable dramatic size, weight and power consumption reductions of chemical analysis instruments. In some embodiments, Raman spectroscopic detection methods and apparatus use ultra-narrow-band angle tuning filters, acousto-optic tuning filters, and temperature tuned filters to enable ultra-miniature analyzers for chemical identification. In some embodiments Raman analysis is conducted along with photoluminescence spectroscopy (i.e. fluorescence and/or phosphorescence spectroscopy) to provide high levels of sensitivity and specificity in the same instrument.

Hug, William F.↗

NASA NTRS2018

Spectroscopic Chemical Analysis Methods and Apparatus

Hug, William F.↗

NASA NTRSDate not supplied

"Giovanni at 20: Consistency and Persistency in Making Earth Remote Sensing Data Available (and Useful) to the Earth Science Community"

Since its creation in the year 2000, the NASA Geospatial Interactive Online Visualization ANd aNalysis Infrastructure (Giovanni) has been an exemplar of how to provide remotely-sensed satellite data and related Earth science datasets to a broad and globally diverse researcher community. One of the hallmarks of Giovanni system usage is that it is common to see practitioners of many branches of science – particularly those in fields not traditionally associated with remote-sensing data, such as animal behavior and paleooceanography – both accessing and employing datasets which the system provides. This usage pattern is attested to by the diversity of published science citing Giovanni. Giovanni has evolved through several versions, each of which increased analytical and visualization options while also enhancing ease-of-use. Information resources supporting Giovanni from the Goddard Earth Sciences Data and Information Services Center (GES DISC), which hosts the system, start with basic mapping and plotting functions and extend to “How-to” recipes demonstrating interusability with other data analysis systems and software. Giovanni is now being developed for use in a cloud environment, potentially expanding datasets the system can be applied to, and also improving performance for data having high spatial and temporal resolution. This presentation covers the system’s historical success with interesting examples of Giovanni-citing research, and will apply its current capabilities to a multi-dataset examination of derecho events associated with mesoscale convective phenomena in the summer of 2020, indicating how Giovanni is prepared for ongoing support of Earth science in a changing world.

Giovanni Derecho visualization↗

NASA NTRS1983

Development of an analytic procedure to calculate damage accumulation in composites during low velocity impact

A computerized procedure was developed to model the response of a laminated composite plate subjected to low velocity impact. The methodology incorporated transient dynamics finite element analysis coupled with composite layer and interlaminar stress predictions. Damage was predicted using a stress based failure criteria and incorporated into the solution as stiffness modifications. The force-displacement relation between the impactor and plate was modelled with a nonlinear contact spring similar to Hertzian contact. Analyses performed predicted ply damage early in the impact event when the displacement fields were characteristic of high frequency flexurable response.

Humphreys, E. A.↗

NASA NTRS1979

Computer and laboratory simulation of interactions between spacecraft surfaces and charged-particle environments

There are two categories of interactions considered in this report. The first, spacecraft passive, refers to cases where the charged-particle environment acts on the spacecraft (e.g., spacecraft charging phenomena). The second, spacecraft active, refers to cases where a system on the spacecraft causes the interaction (e.g., high voltage space power systems). Both categories are studied in ground simulation facilities to understand the processes involved and to measure the pertinent parameters. Computer simulations are based on the NASA Charging Analyzer Program (NASCAP) code. Analytical models are developed in this code and verified against the experimental data. Extrapolation from the small test samples to space conditions are made with this code. Typical results from laboratory and computer simulations are presented for both types of interactions. Extrapolations from these simulations to performance in space environments are discussed.

Stevens, N. J.↗