Engineering Papers⌕ Search

SEARCH · Engineering Papers

Results for “high modulus”

Search indexed NASA NTRS and DOE OSTI research on propulsion, heat transfer, battery materials and energy systems. Follow report and document links to the original sources.

Quote a phrase for an exact phrase match. Source license links do not imply unrestricted reuse.

At least 775 records · Page 43
All sourcesNASA NTRSDOE OSTI
NASA NTRS1973

A shock-induced phase change in orthoclase.

New shock compression data to 340 kb for single-crystal orthoclase (along (001)), demonstrate the onset of a shock-induced phase change at about 115 kb. Along the Hugoniot a mixed-phase region extends to about 300 kb, above which the data are believed to correspond to the properties of a high-pressure phase having the hollandite structure (zero pressure density of 3.84 g/cu cm) reported by Ringwood et al. If the hollandite value for the zero pressure density is used, the zero pressure bulk modulus of this phase is approximately 1.8 plus or minus 0.2 Mb.

Ahrens, T. J.↗
NASA NTRS1978

Measurement of the time-temperature dependent dynamic mechanical properties of boron/aluminum composites

A flexural vibration test and associated equipment were developed to accurately measure the low strain dynamic modulus and damping of composite materials from -200 C to over 500 C. The basic test method involves the forced vibration of composite bars at their resonant free-free flexural modes in a high vacuum cryostat furnace. The accuracy of these expressions and the flexural test was verified by dynamic moduli and damping capacity measurements on 50 fiber volume percent boron/aluminum (B/Al) composites vibrating near 2000 Hz. The phase results were summarized to permit predictions of the B/Al dynamic behavior as a function of frequency, temperature, and fiber volume fraction.

Dicarlo, J. A.↗
NASA NTRS2006

Properties of a Ni(sub 19.5)Pd(sub 30)Ti(sub 50.5) high-temperature shape memory alloy in tension and compression

Potential applications involving high-temperature shape memory alloys have been growing in recent years. Even in those cases where promising new alloys have been identified, the knowledge base for such materials contains gaps crucial to their maturation and implementation in actuator and other applications. We begin to address this issue by characterizing the mechanical behavior of a Ni19.5Pd30Ti50.5 high-temperature shape memory alloy in both uniaxial tension and compression at various temperatures. Differences in the isothermal uniaxial deformation behavior were most notable at test temperatures below the martensite finish temperature. The elastic modulus of the material was very dependent on strain level; therefore, dynamic Young#s Modulus was determined as a function of temperature by an impulse excitation technique. More importantly, the performance of a thermally activated actuator material is dependent on the work output of the alloy. Consequently, the strain-temperature response of the Ni19.5Pd30Ti50.5 alloy under various loads was determined in both tension and compression and the specific work output calculated and compared in both loading conditions. It was found that the transformation strain and thus, the specific work output were similar regardless of the loading condition. Also, in both tension and compression, the strain-temperature loops determined under constant load conditions did not close due to the fact that the transformation strain during cooling was always larger than the transformation strain during heating. This was apparently the result of permanent plastic deformation of the martensite phase with each cycle. Consequently, before this alloy can be used under cyclic actuation conditions, modification of the microstructure or composition would be required to increase the resistance of the alloy to plastic deformation by slip.

Noebe, Ronald↗
DOE OSTI2026

Valorization of consolidated bioprocessing residues for bioplastics

This study demonstrates an organic solvent-free processing strategy to valorize consolidated bioprocessing (CBP) residues, from switchgrass and poplar biomass, into functional poly(butylene succinate) (PBS)-based biocomposites using high-shear homogenization (HSH). HSH transformed the switchgrass and poplar CBP residues (CBP-R) into fine, uniformly distributed particles and microfibers. The composites of PBS with homogenized switchgrass residues (H-CBP-R-SG) or homogenized poplar residues (H-CBP-R-P) at a 70/30 weight ratio exhibited improved processability and mechanical integrity, with the Young's modulus for the PBS/H-CBP-R-SG and PBS/H-CBP-R-P nearly doubling to 0.66 ± 0.07 GPa and 0.65 ± 0.04 GPa, respectively, compared to neat PBS (0.36 ± 0.02 GPa). Dynamic Mechanical Analysis (DMA) reveals a significant suppression of the tan δ peak magnitude, indicating that HSH-mediated physical activation facilitates stress transfer in composites typical of covalent chemical grafting systems. While the transition to a stiffness-dominated profile reduces ductility, the resulting composites exhibit the dimensional stability and resistance to thermal warping required for high-fidelity FDM 3D printing and injection molding. Beyond material performance, comprehensive techno-economic analysis (TEA) and life cycle assessment (LCA) confirmed that diverting CBP residues into composite products can improve the economic viability of the biorefinery without substantially increasing biorefinery global warming potential (GWP). At a 30 wt% blend ratio, incorporating residuals into PBS yielded a minimum selling price for the composite of $\$4.07$ per kg compared to the conventional bioplastic price of $\$5.00$ per kg. This approach aligns with circular bioeconomy principles by converting waste streams into value-added products. Furthermore, this innovative strategy addresses key challenges in bioplastic development, including cost, compatibility, and performance, while simultaneously advancing waste minimization strategies for sustainable manufacturing systems.

09 BIOMASS FUELS↗
DOE OSTI2020

Well-designed Crosslinked Polymer Electrolyte Enables High Ionic Conductivity and Enhanced Salt Solvation

A new facile single-step method to fabricate crosslinked polymer electrolyte membranes consisting of branched poly(ethyleneimine), (PEI) and poly(ethylene oxide), (PEO) is demonstrated. The membranes exhibit excellent ionic conductivity (1.2 × 10 –3 S cm –1 at 80 °C) with minimal addition of plasticizer (20 wt%). The amine functional group in the PEI-PEO crosslinked matrix provides Lewis basic and hydrogen bonding characteristics that facilitate the dissolution of lithium salt and enables a higher cation transport number than a PEO crosslinked matrix. The glass transition temperature, degree of crystallinity, and room temperature storage modulus increases with decreasing crosslink density and increasing ratio of free amines. The resultant ionic conductivity and mechanical strength can be flexibly tailored by varying the molar ratio of free amine moieties in the crosslinked PEI-PEO matrix. This study provides an improved synthesis method, in-depth characterization, and fundamental insights on the effect of free amine moieties on the transport properties of a highly conductive gel polymer electrolyte.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2020

Machine-learning informed prediction of high-entropy solid solution formation: Beyond the Hume-Rothery rules

The empirical rules for the prediction of solid solution formation proposed so far in the literature usually have very compromised predictability. Some rules with seemingly good predictability were, however, tested using small data sets. Based on an unprecedented large dataset containing 1252 multicomponent alloys, machine-learning methods showed that the formation of solid solutions can be very accurately predicted (93%). The machine-learning results help identify the most important features, such as molar volume, bulk modulus, and melting temperature. As such a new thermodynamics-based rule was developed to predict solid–solution alloys. The new rule is nonetheless slightly less accurate (73%) but has roots in the physical nature of the problem. The new rule is employed to predict solid solutions existing in the three blocks, each of which consists of 9 elements. The predictions encompass face-centered cubic (FCC), body-centered cubic (BCC), and hexagonal closest packed (HCP) structures in a high throughput manner. The validity of the prediction is further confirmed by CALculations of PHAse Diagram (CALPHAD) calculations with high consistency (94%). Since the new thermodynamics-based rule employs only elemental properties, applicability in screening for solid solution high-entropy alloys is straightforward and efficient.

36 MATERIALS SCIENCE↗
DOE OSTI2022

3D printing of a recycled copolyester of terephthalic acid, cyclohexanedimethanol and tetramethylcyclobutanediol

2,2,4,4-Tetramethyl-1,3-cyclobutanediol (TMCD) is a diol monomer for terephthalic acid (TPA) class of copolyesters that can increase the glass transition temperature and mechanical strength in comparison to conventional TPA polyesters. TMCD-modified poly (1,4-cyclohexylenedimethylene terephthalate) (PCTT) has been used to manufacture consumer products with good toughness, heat resistance and clarity. However, the suitability of PCTT in 3D printing had not been evaluated. Therefore, consumer plasticware was used as the starting material to investigate the suitability of this copolyester for fused deposition modeling (FDM). Here, chemical structure, mechanical properties, thermal behavior and viscoelastic properties of this copolyester were studied. NMR spectroscopy found that the copolyester had cyclohexanedimethanol (CHDM) and TMCD contents at 76.5 mol% and 20 mol% of total diol, respectively. 280 °C printing temperature and 110 °C bed temperature were suitable conditions for printing. T g of PCTT was 103 °C (25 °C higher than PETG). Young's modulus and impact strength of printed PCTT were at least 100% and 65% higher than printed PETG, respectively. The ease of printing, superior mechanical properties and T g (103 °C) make the PCTT random copolyester highly applicable in additive manufacturing.

36 MATERIALS SCIENCE↗
DOE OSTI2026

Investigating property-porosity relationships for micro-architected lattice structures

Micro-architected structures are increasingly valued for their light weight and tunable mechanical properties; this class of material includes sheet structures like the Schöen gyroid and beam lattices like the octet. For design purposes, it is critical to understand how to tune the relative density (RD) to obtain desired mechanical properties. This study investigates the mechanical response of Ti-6Al-4V gyroid structures, spanning a broad range of RDs (0.03–0.90), unit cell sizes (1–4 cm), and sheet thicknesses (0.2–7.8 mm). Results demonstrate that the classical Gibson-Ashby power law scaling between RD and modulus and yield stress does not adequately capture the response over a wide range of RDs, nor does it extrapolate correctly to the fully dense solid. Analytical models, in concert with experimental results and high-fidelity finite element calculations, show that the deviation from Gibson-Ashby reflects a transition from structure-dominated to material-dominated behavior. Distinctions are drawn between scaling relationships and property-porosity models, and an analytical model is proposed to better capture the evolution of mechanical properties with RD. These observations are mirrored in other architected topologies, like the octet, and highlight the importance of understanding the relationship between mechanical properties and geometry for design purposes.

Materials science↗
DOE OSTI2021

Ab initio anharmonic thermodynamic properties of cubic Ca Si O 3 perovskite

We present an ab initio study of the thermodynamic properties of cubic CaSiO 3 perovskite (CaPv) over the pressure and temperature range of the Earth's lower mantle. We compute the anharmonic phonon dispersions throughout the Brillouin zone by utilizing the phonon quasiparticle approach, which characterizes the intrinsic temperature dependence of phonon frequencies and, in principle, captures full anharmonicity. Such temperature-dependent phonon dispersions are used to calculate ab initio free energy in the thermodynamic limit (N → ∞) within the framework of the phonon gas model. Accurate free energy calculations enable us to investigate cubic CaPv's thermodynamic properties, e.g., thermal expansivity, Grüneisen parameter, bulk modulus, heat capacity and thermal equation of state, where anharmonic effects are demonstrated. Furthermore, the present methodology provides an important theoretical approach for exploring phase boundaries, thermodynamic, and thermoelastic properties of strongly anharmonic materials at high pressures and temperatures.

75 CONDENSED MATTER PHYSICS, SUPERCONDUCTIVITY AND↗
DOE OSTI2022

Characterization of Properties of Laser Powder Bed Fusion 3D-Printed Inconel 718 for Centrifugal Turbomachinery Applications

Here, this paper presents the results of a comprehensive effort to characterize the properties of Inconel 718 produced by a form of laser powder bed fusion (LPBF) additive manufacturing (AM) or 3D-printing, subsequently subjected to hot isostatic pressing (HIP) and heat treatment according to standards F3055-14a and AMS 5663, respectively. Material property data, while broadly available for traditional Inconel 718 presentations (e.g. forgings or castings), is currently lacking for the 3D-printed material. It is expected that while limited in size, the experimental data sets presented provide sufficient information to glean the capability of LPBF Inconel 718. These include: 1) Chemical composition, electron backscatter diffraction (EBSD), and x-ray energy dispersive spectroscopy (XEDS) characterization of 3D-printed material structure; 2) Tensile properties — 0.2% yield stress, ultimate stress, modulus of elasticity, and elongation to failure — based on 108 samples, as functions of temperature and sample print orientation; 3) Creep rupture data including the Larson-Miller parameter, based on 21 samples; and 4) High cycle fatigue data based on 21 samples as a function of temperature. Results are compared to available standards and/or data for forged, cast, and other AM Inconel 718. A key observation of this study, based on the EBSD results, is that while the material appears to approach full recrystallization following heat treatment, there is a detectable fraction of the material that does not fully recrystallize, resulting in a material with mechanical properties (e.g. yield stress, creep rupture) measurably lower than those of forgings, but higher than those of castings.

30 DIRECT ENERGY CONVERSION↗
NASA NTRS1995

A study of the relationship between mineral content and mechanical properties of turkey gastrocnemius tendon

The vertebrate skeletal system undergoes adaptation in response to external forces, but the relation between the skeletal changes and such forces is not understood. In this context, the variation in the amount and location of calcification has been compared with changes in mechanical properties of the normally mineralizing turkey gastrocnemius tendon using ash weight measurements, X-ray radiography, and mechanical testing. Radiographic evidence from 12- to 17-week-old birds showed calcification in only portions of gastrocnemius tendons proximal to the tarsometatarsal joint. Mechanical testing of these dissected proximal regions demonstrated an increased ultimate stress and modulus and a decreased maximum strain that appeared to parallel calcification. Further, stress-strain curves of portions of uncalcified turkey gastrocnemius tendon were shaped similar to those of other typical unmineralized tendon curves while highly calcified tendons yielded curves resembling those of bone. The proximal portions of the gastrocnemius where mineralization begins were observed to have a decreased tendon cross-sectional area compared with distal portions which do not mineralize. Based on the resultant measures of mineral content and location and mechanical properties, it is hypothesized that increased calcification is a result of increased stresses at certain locations of the tendon, perhaps the consequence of the natural forces exerted by the large leg muscles of the bird into which the gastrocnemius inserts. More specifically, tendon calcification may be the result of stress-induced exposure of charged sites on the surfaces of collagen molecules, fibrils, or fibers so that deposition of mineral and subsequent mechanical reinforcement occur in the tissue.(ABSTRACT TRUNCATED AT 250 WORDS).

Non-NASA Center↗
NASA NTRS1994

Tribological evaluation of an Al2O3-SiO2 ceramic fiber candidate for high temperature sliding seals

A test program to determine the relative sliding durability of an alumina-silica candidate ceramic fiber for high temperature sliding seal applications is described. Pin-on-disk tests were used to evaluate the potential seal material by sliding a tow or bundle of the candidate ceramic fiber against a superalloy test disk. Friction was measured during the tests and fiber wear, indicated by the extent of fibers broken in the tow or bundle, was measured at the end of each test. Test variables studied included ambient temperatures from 25 to 900 C, loads from 1.3 to 21.2 N, and sliding velocities from 0.025 to 0.25 m/sec. In addition, the effects of fiber diameter and elastic modulus on friction and wear were measured. Thin gold films deposited on the superalloy disk surface were evaluated in an effort to reduce friction and wear of the fibers. In most cases, wear increased with test temperature. Friction ranged from 0.36 at 500 C and low velocity (0.025 m/sec) to over 1.1 at 900 C and high velocity (0.25 m/sec). The gold films resulted in satisfactory lubrication of the fibers at 25 C. At elevated temperatures diffusion of substrate elements degraded the films. These results indicate that the alumina-silica (Al2O3-SiO2) fiber is a good candidate material system for high temperature sliding seal applications. More work is needed to reduce friction.

Dellacorte, Christopher↗
DOE OSTI2020

Stability of Tin-Lead Halide Perovskite Solar Cells

Tin-lead perovskites have low band gaps (1.2 eV - 1.4 eV) that offer complementary absorption spectra to mixed halide perovskites with band gaps in the range of 1.6 eV - 1.85 eV. In combination, tin-lead and mixed halide perovskites can be used to make efficient all-perovskite tandem solar cells. While these can achieve high efficiency, they are hampered by the unproven longterm stability of tin-containing perovskites. We make the first demonstration of tin-lead perovskite solar cells that pass benchmark 1000-hour tests of stability under stressors of heat, light, and atmospheric exposure. We identify that mixed tin-lead perovskites oxidise by a different chemical pathway, one that is much less favourable, than the oxidation pathway followed by pure tin perovskites, making them significantly more stable. Fortuitously, mixed tin-lead perovskites also have band gaps that are close to ideal for the rear cell of an all-perovskite monolithic two-junction tandem. Beyond selecting the composition of the perovskite to be one that has inherently suppressed tendency to oxidise, we also fabricate a novel heterojunction-based architecture that eliminates the commonly used acidic PEDOT:PSS layer, which leads to enhanced stability. By packaging the resulting solar cell in a glass-on-glass package with a pliable low-elastic-modulus polyolefin encapsulant and a butyl rubber edge seal, we also demonstrate that the low band gap perovskite solar cell that passes the IEC damp heat test for thin film solar cells - a milestone that demonstrates the removal of a significant impediment to the commercialization of high efficiency perovskite tandem solar cells.

14 SOLAR ENERGY↗
DOE OSTI2020

Dimensional interpolation for metallic hydrogen

In this work, we employ a simple and mostly accurate dimensional interpolation formula using dimensional limits D = 1 and D = ∞ to obtain D = 3 ground-state energy of metallic hydrogen. We also present results describing the phase transitions for different symmetries of three-dimensional structure lattices. The interpolation formula not only predicts fairly accurate energies but also predicts a correct functional form of the energy as a function of the lattice parameters. That allows us to calculate different physical quantities such as the bulk modulus, Debye temperature, and critical transition temperature, from the gradient and the curvature of the energy curve as a function of the lattice parameters. These theoretical calculations suggest that metallic hydrogen is a likely candidate for high temperature superconductivity. The dimensional interpolation formula is robust and might be useful to obtain the energies of complex many-body systems.

37 INORGANIC, ORGANIC, PHYSICAL, AND ANALYTICAL CH↗
DOE OSTI2024

Manufacturing Cathodes via Dry-Processing for Lithium-Ion Batteries

Conventional lithium-ion battery (LIB) electrodes are prepared through a wet slurry process with n-methyl pyrrolidone solvent, especially for cathodes. The wet slurry process encounters several disadvantages such as binder migration, electrode cracking in thick electrodes, energy intense heat-dry NMP solvent removal, and costly NMP recovery. The cost and energy consumption of coating and drying of electrode are about 11.5 % and > 46 % in LIB manufacturing, respectively. Thereby, it is essential to develop a facile roll-to-roll solvent-free LIB electrode processing for reducing the cost and energy consumption. Recently, the Maxwell-type dry processing (DP) shines new lights on LIB manufacturing, which mainly bases on dry mixing (DM) of electrode component powder followed by calendering into electrode films and laminating onto current collectors, realizing the rapid manufacturing of LIB electrodes in a powder-to-film manner for industries. This report shares some recent progress on the DP from our group. We aim to further advance the manufacturing science of DP by correlating the processing conditions with electrode properties and performance. Particularly, we investigate the effect of DM, and compression on the polytetrafluoroethylene (PTFE) binder fiberization, porosity, mechanical properties, electrical conductivity and electrochemical behaviors of electrodes. The DM study suggests that PTFE fiberization heavily relies on the degree of DM. Insufficient DM results in poor PTFE fiberization while outrageous DM damages the formed PTFE fibers. Both negatively affect the mechanical behaviors of the electrodes and their rate capability. However, moderate DM is highly beneficial. In addition, our study of the porosity impact reveals that LiNi0.8Mn0.1Co0.1O2 (NMC) secondary particles can be broken into primary particles due to compression, especially at low porosity. Those fractured NMC secondary particles exhibit lower modulus. We propose that a moderate porosity of around 32% favors the electronic conductivity, charge transfer impedance and rate capability. The study of the cathodic electrolyte interphase layer of PTFE-based DPed electrode confirms that side reactions of PTFE binder due to the formation of LiF in LiClO4-based electrolyte.

Tao, Runming↗
NASA NTRS2003

Determination of Significant Composite Processing Factors by Designed Experiment (MSFC Center Director's Discretionary Fund)

To determie composite material properties' effects from porcessing variables, a 3 factorial designed experiment with two replicates was conducted. The factors were cure method (oven versus autoclave), layup (hand versus tape-laying machine), and thickness (8 versus 52 ply). Four material systems were tested: AS4/3501-6, IM7/8551-7, IM7/F655 bismaleimide (BMI), and shear tests on IM7/F584. Material properties were G(sub 12), v(sub 12), E(sub 1c) and E(sub 2c). Since the samples were necessarily nonstandard, strengths, though recorded, cannot be considered valid. Void content was also compared. Autoclave curing helped material properties for the low modulus fiber material but showed little benefit for higher stiffness fibers. The number of plies was very important for epoxy composites but not for the BMI. E(sub 1) was generally unaffected by any factor. Particularly high void content did correlate to reduced properties. Autoclave curing reduced void content over oven curiing but a moderate amount of voids, less than 1 percent void content, didnot correlate with material properties. Oven cures and hand layups can produce high-quality parts. Part thickness of epoxy composites is important, though cure optimization may improve performance. Significant variations can be caused by processing and it is important that test coupons always reflect the layup and processes of the final part.

Finckenor, J. L.↗
NASA NTRS2015

Use of a Tantalum Liner to Reduce Bore Erosion and Increase Muzzle Velocity in Two-Stage Light Gas Guns

Muzzle velocities and gun erosion predicted by earlier numerical simulations of two stage light gas guns with steel gun tubes were in good agreement with experimental values. In a subsequent study, simulations of high performance shots were repeated with rhenium (Re) gun tubes. Large increases in muzzle velocity (2 - 4 km/sec) were predicted for Re tubes. In addition, the hydrogen-produced gun tube erosion was, in general, predicted to be zero with Re tubes. Tantalum (Ta) has some mechanical properties superior to those of Re. Tantalum has a lower modulus of elasticity than Re for better force transmission from the refractory metal liner to an underlying thick wall steel tube. Tantalum also has greater ductility than Re for better survivability during severe stress/strain cycles. Also, tantalum has been used as a coating or liner in military powder guns with encouraging results. Tantalum has, however, somewhat inferior thermal properties to those of rhenium, with a lower melting point and lower density and thermal conductivity. The present study was undertaken to see to what degree the muzzle velocity gains of rhenium gun tubes (over steel tubes) could be achieved with tantalum gun tubes. Nine high performance shots were modeled with a new version of our CFD gun code for steel, rhenium and tantalum gun tubes. For all except the highest velocity shot, the results with Ta tubes were nearly identical with those for Re tubes. Even for the highest velocity shot, the muzzle velocity gain over a steel tube using Ta was 82% of the gain obtained using Re. Thus, the somewhat inferior thermal properties of Ta (when compared to those of Re) translate into only very slightly poorer overall muzzle velocity performance. When this fact is combined with the superior mechanical properties of Ta and the encouraging performance of Ta liners/coatings in military powder guns, tantalum is to be preferred over Re as a liner/coating material for two stage light gas guns to increase muzzle velocity and reduce bore erosion.

Launchers↗
DOE OSTI2026

Dynamic Interfacial Design in Adaptive Hybrid Materials Enables Reversible and Tunable Mechano-Optic Smart Responses

Next-generation polymeric materials are shifting toward adaptive and interactive behaviors of living systems; however, designing materials that can reversibly modulate optical properties under mechanical deformation while maintaining mechanical robustness remains a key challenge. Here, we report a mechanically robust vitrimer-based adaptive hybrid material (AHM) that exhibits a stretch-induced reversible transparency-to-opacity transition, enabled by the integration of dynamic interactions at the polymer–silica nanoparticle interface and controlled nanoparticle self-assembly. The AHM combines boronic ester–functionalized polystyrene-b-poly(ethylene-co-butylene)-b-polystyrene (S-Bpin) with diol-functionalized silica nanoparticles (diol-SiNPs) to form a hybrid network hosting both dynamic boronic ester and hydrogen-bonding interactions. These reversible linkages facilitate controlled nanoparticle self-assembly and enable strain-induced nanoparticle alignment/aggregation. Upon stretching, SiNP-rich domains align and aggregate within the polymer matrix, while local modulus mismatch between stiff aggregated SiNP/borylated-styrene-rich regions and the softer elastomeric midblock induces surface microwrinkle formation. These internal aggregates and surface wrinkles cooperatively enhance light scattering, producing the opaque state under strain. Furthermore, the tailored AHM exhibits high toughness, thermomechanical stability, reprocessability, and programmable shape-memory behavior. This work presents a dynamic interfacial design strategy for mechanically robust, optically reconfigurable, and reusable soft materials for adaptive optics, smart windows, sensing, soft robotics, and circular smart-material platforms.

adaptive hybrid materials↗